VIP-450 SIP command Reference Guide
The VIP-450 is a SIP version 2.0 compliant voice gateway, which integrates a
web-based graphical user interface, and command line administration that can cover
most configurations and application demands.
Command Reference Guide
PLANET VIP-450 SIP Reference Guide
TABLE OF CONTENTS
1. ABOUT THIS GUIDE………………………………………………………………3
2. SIP COMMAND REFERENCE.………………….………………………………..3
3. DIAL PLAN SETUP..…..……………………………………………………………5
4. CALL TRANSFER…………………………………………………………………..5
5. CONFIGURATION EXAMPLE…...……………………………………………….6
2
PLANET VIP-450 SIP Reference Guide
ABOUT THIS GUIDE
This VIP-450 SIP (Session Initiation Protocol) Reference Guide provides SIP configuration commands.
Before starting configurations, it is suggested to check the SIP connection requirement carefully, then
configure the required value in machine. If you’re not sure which parameters should be inserted, please
check this guide for corresponding parameters to establish the voice connection on your side. In the
meantime, more VOIP concept and machine design algorithm can be referred in the user’s manual CD for
more understandings.
This Guide contains the following information:
SIP Command Reference: This chapter illustrates how to use the sip command for the Internet
Telephony Gateway (ITG), to register with the SIP proxy server.
Dial Plan Set Up: Shows the difference between the H.323 and SIP protocol.
Call Transfer: This chapter illustrates the operations of call transfer.
Configuration Example: This chapter shows you how to set up the ITG to start up your call.
Before reading this guide, it is best that you are familiar with the “QUICK INSTALLATION GUIDE” and
you know the network configurations, as well as the dial plan set up.
3
PLANET VIP-450 SIP Reference Guide
1. SIP COMMAND REFERENCE
show sip reg
- displays the information of registration
show sip cfg
- displays the configuration of registration
show sip proxy
- displays the configuration of proxy server
show sip dns_ip
- displays the configuration of DNS server
show sip info_sw
-
displays the information switch
show sip auto_reg
- displays auto-registration on/off when reboot
show sip nat_call
- displays nat_call switch
show sip outboundproxy
- displays the outbound proxy
set sip reg add
- used to add registration information
set sip reg add [reg_num] [expires] [#registrar] [ip] [port] {name | 0} {passwd |
4
0} {ip port …}
PLANET VIP-450 SIP Reference Guide
Syntax description
reg_num
expires how long the reg_num is to re-register
#registrar
ip
port port of the registrar
name
passwd
the phone number to be registered
the number of registrar
IP of the registrar
[the name for authentication | 0 for no authentication]
[the password for authentication | 0 for no authentication]
set sip reg del
- used to delete registration information
set sip reg del [reg_num]
Syntax description
reg_num
the phone number to be deleted
set sip cfg
- used to set the configuration of sip
set sip cfg
Syntax description
[udp_ctl_port] [rtp_data_port]
udp_ctl_port
rtp_data_port <rtp data port>|( 0 : default port will be used)
<udp control port>|( 0 : default port will be used)
set sip proxy
- used to set the configuration of sip
set sip proxy
[#proxy_svr] [ proxy svr-1 nwa ] { proxy svr-2 nwa }…
Syntax description
#proxy_svr
proxy svr nwa <ip> <port>
number of proxy server | 0 to remove existing server
set sip actreg
5
PLANET VIP-450 SIP Reference Guide
- used to send out the registration
set sip actreg
set sip dns_ip
- used to set the domain name server. The IP domain should be in
numerical format
set sip dns_ip [ip]
Syntax description
ip
<x.x.x.x> | 0 to remove dns ip
set sip info_sw
- used to set the sip process information switch
set sip info_sw [on/off]
set sip auto_reg
- used to set registration auto start when reboot in the condition of registration
server is set
set sip auto_reg [on/off]
set sip nat_call
- used to set nat_call switch on/off whether the gateway in public IP is to receive
calls from the private IP or not. The default is on
set sip nat_call [on/off]
set sip outboundproxy add
- used to add outbound proxy
set sip outboundproxy add [ip/hostname] [port]
set sip outboundproxy del
- used to delete outbound proxy
set sip outboundproxy del
6
PLANET VIP-450 SIP Reference Guide
2. DIAL PLAN SETUP
Here, we list the differences between the H.323 and SIP dialplan configurations. If you are not familiar
with machine dialplan setup, please refer to the VIP Quick Installation Guide and the User’s manual
for more understandings of the dialplan operations in machine.
Calling destination in PLANET H.323 voice gateways can be added via following commands:
atpm dadd [dest_id] h323 [dest ip addr] [port]
atpm dadd [dest_id] dns [dest host name] [port]
In VIP-450 the “h323” part in the command is replaced by “sip”:
atpm dadd [dest_id] sip [dest ip addr] [port]
atpm dadd [dest_id] dns [dest host name] [port]
3. CALL TRANSFER
VIP-450 supports unattended call transfer.
3-1 The Operations
When a remote session is established, both ends of the parties can transfer a call to another location
by pressing the Flash/Transfer keypad on the phone set.
3-2 Operation Recovery
When the user is transferring a call to a destination that does not exist on the dial plan, an
out-of-service tone will be generated. Pressing the Flash/Transfer keypad can bring users back to
the original session.
4. CONFIGURATION EXAMPLE
Now, it is assumed that you are registering to a proxy server (referred to registrar). The information for
registration is as follows:
ITG IP: 211.20.1.5
Registered ID: 2001
7
PLANET VIP-450 SIP Reference Guide
Expired Time: 500
Proxy Server IP: 211.20.1.1
Proxy Server Port: 5060
Set the information of registration.
ITG>set sip reg 2001 500 1 211.20.1.5 5060 0 0
Then you need set up the server.
ITG>set sip cfg 0 0
Then you need set up the server.
ITG>set sip proxy 1 211.20.1.1 5060
In order to support the complete function, you need to set a port cid number. We assume port 0 is used.
ITG>set port 0 cid number 2001
Next, you need to save the information and send out the registration.
ITG>config activate
ITG>config store
ITG>set sip actreg
*Note: Before starting the first call, you need to set up the dial plan. Don’t forget to use “sip” when you
type “atpm dadd”.
8
Loading...