Planet VIP-100T Quick Installation Manual

Trademarks

Copyright  PLANET Technology Corp. 2003.
Contents subject to revise without prior notice.
PLANET is a registered trademark of PLANET Technology

Corp. All other trademarks belong to their respective
owners.

FCC Warning

This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the Instruction manual, may cause
harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause
harmful interference in which case the You will be required
to correct the interference at his own expense.

CE-mark Warning

This is a Class A product. In a domestic environment, this
product may cause radio interference, in which case the
You may be required to take adequate measures.

Revision

PLANET IP Phone VIP-100T
QUICK INSTALLATION GUIDE

For model: VIP-100T
Part No.: EMQ-VIP100TV1

PLANET VoIP

TABLE OF CONTENTS

1. OVERVIEW........................................................................5

1.1 BEFORE STARTUP ...........................................................6

1.2 P

2. BASIC CONFIGURATION..............................................10

2.1 INITIALIZE VIP-100T......................................................10

3. MAKING CALLS.............................................................18

HYSICAL DETAILS

1.2.1 Front view and keypad function:.............................7

1.2.2 Rear view................................................................9

2.1.1 Start up..................................................................10

2.1.2 LCD configuration.................................................11

2.1.2.1 System Configuration..............................................11

(i) Connect Configuration.................................................12

(ii) User Line Number.......................................................16

(iii) Firmware Update........................................................16

(iv) Hardware Test...........................................................17

(v) Reboot........................................................................17

..........................................................6

3.1 IP

3.1.1 P2P mode Operation Steps:.................................19

3.2 GK MODE OPERATION STEPS:.......................................22

3.3 QUICK DIAL EXAMPLE.....................................................25

3.3.1 Dial to local in peer to peer (P2P) mode...............25

3.3.2 Phone Book web configuration sample.................26

4. QUICK REFERENCE IN CD-ROM GUIDE.....................27

ADDRESS CALL

(P2P

MODE

):......................................18

VIP-100T Quick Installation Guide

1. OVERVIEW

Thank you for purchasing PLANET IP Phone VIP-100T
(VIP-100T, in the following terms). You can now ease the cost of
long distance call yet still enjoy the toll voice quality via Internet.

This Guide contains the following information:
Product Overview:

This chapter brings you brief introduction to VIP-100T, and
illustrates machine physical view, operation and
functionality.

Network Configuration:

This chapter illustrates how to setup the Gateway through
console interface and Web interface to your network.

Basic Configuration:

With console command, you will learn how to have the
command to the VIP and get the information from it as
well.

Configuration Example:

This chapter shows you how to use the default settings
start up your first call. And some examples show you how
to cooperate with other devices.

Quick Reference:

Since there are lots of commands in the Gateway, we also
recommend you to learn more from the bundled CD-ROM
manual.

VIP-100T Quick Installation Guide

Function

1.1 Before Startup

Before your first time start up, please check if the package
comes with following items:

l VIP-100T
l Your manual CD
l Quick Installation Guide
l RJ-45 cable

And later, you are required to familiar your environment, your
TCP/IP network and your phone systems.

1.2 Physical Details

LCD

Display

Speed

Dial

Key pad

Key

PLANET VoIP

1.2.1 Front view and keypad function:

♦ C

: Cancel and Clear

♦ çè : Move to left /previous and right/next.
♦ OK

: Press OK to confirm the modification.

♦ Direct Line (DL) Button 1 – 10: Speed dialing according

to phone book data 1-10.

(Please refer to LCD configuration [Phone Address Book] )

♦ “+” and “- “ key: Adjust voice volume in communication.
♦ SPEAKER: Speaking without picking up handset.

♦ MUTE

: Mute the voice of MIC and let others can’t hear

from You in communication.

♦ HOLD

: To hold a call with H.450 function.

♦ SPEED: Press SPEED and number (Phone book index) to

do speed dial according to phone book data.

♦ FORWARD: Forward an incoming call to another IP

device by H.450 forward function. (Please
refer to LCD configuration [Indicate
Forward Type])

♦ MESSAGE and its indicated LED light: When missing

the incoming calls, the message LED will be flashing. You
can know the information of miss call by pressing the
message button.

VIP-100T Quick Installation Guide

2

♦ TRANSFER:

1. Transfer a call by H.450 transfer function. Press
TRANSFER button in communication and press

phone No. which You want to transferred to can
transfer this call .

2. Change characters to be capital or lowercase:
when press TRANSFER before press letters can
switch type of letters.

♦ REDIAL: Redial the last outgoing call.
♦

♦

Number 1 –10, * and #: The function is as the same as
the general phone set.

Corresponding list of keypad and symbol:

1 “Space” ; “,” ; “.” ; “!” ; “1”

“A” ; “ B” ; “C” ; “2”
3 “D” ; “E” ; “F” ; “3”
4 “G” ; “H” ; “I” ; “4”
5 “J” ; “K” ; “L” ; “5”
6 “M” ; “N” ; “O” ; “6”
7 “P” ; “Q” ; “R” ; “S” ; “7”
8 “T” ; “U” ; “V” ; “8”

9 “W” ; “X” ; “Y” ; “Z” ; “9”
* “-“ ; “?” ; “*”
0 “0”
# “_” ; “@” ; “#”

PLANET VoIP

through

Two LED indicated lights; LNK/ACT and 10/100 for

status is in

normal, LED of LINK/ACT will be flashing; when

will

1.2.2 Rear view

9V DC

9V DC Power input outlet

LAN RJ-45 connector, connected directly to Switch/Hub

through straight CAT-5 cable.

RJ-45 connector, connected directly to the

PC

straight

CAT-5 cable

PC

LED
Display

LAN port and PC port. When network
transmit rate is in 10 Mbps/100Mbps, LED of 100

light off/on.

VIP-100T Quick Installation Guide