PLANET VF-402-KIT User Manual

4-Channel Video over Fiber Bundle Kit

VF-402-KIT

Manual

Copyright © 2013 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET.

PLANET makes no representations or warranties, either expressed or implied,

with respect to the contents hereof and specically disclaims any warranties, merchantability or tness for any particular purpose. Any software described in this

manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not PLANET, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further, PLANET reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.

All brand and product names mentioned in this manual are trademarks and/or registered trademarks of their respective holders.

Federal Communication Commission Interference Statement

This device has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the device and receiver.

3. Connect the device into an outlet on a circuit different from that to which the

receiver is connected.

4. Consult the dealer or an experienced radio technician for help.

FCC Caution

To assure continued compliance. (example-use only shielded interface cables when

connecting to computer or peripheral devices). Any changes or modications not

expressly approved by the party responsible for compliance could void the user’s authority to operate the device.

This device complies with Part 15 of the FCC Rules. Operation is subject to the Following two conditions: (1) This device may not cause harmful interference, and (2) this Device must accept any interference received, including interference that may cause undesired operation.

Federal Communication Commission (FCC) Radiation Exposure Statement

This device complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation.

Safety

This device is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical device. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the device.

CE Mark Warning

This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

CE in which Countries where the product may be used freely:

Germany, UK, Italy, Spain, Belgium, Netherlands, Portugal, Greece, Ireland, Denmark, Luxembourg, Austria, Finland, Sweden, Norway and Iceland.

France: except the channel 10 through 13, law prohibits the use of other channels.

Safety

This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment.

National Restrictions

This device is intended for home and ofce use in all EU countries (and other

countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:

WEEE Regulation

To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic

device, end users of electrical and electronic device should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.

Revision

User’s Manual for 4-Channel Video over Fiber Bundle Kit (VF-402- T + VF-402-R) Model: VF-402-KIT Rev: 1.1 (January 2013) Part No. EM-VF-402-KIT

Table of Contents

Chapter 1. Product Introduction ........................................................................ 6

1.1 Package Contents ................................................................................ 6

1.2 Product Description .............................................................................. 6

1.3 Application .......................................................................................... 9

1.4 Product Features ................................................................................10

1.5 Product Specication ...........................................................................10

1.6 Dimension of Installing .......................................................................12

Chapter 2. Hardware Description

2.1 Panel Overview ..................................................................................13

Chapter 3. Installation

3.1 Limitation ..........................................................................................15

3.2 Preparation before Installing ................................................................15

3.3 Order for installation ...........................................................................16

3.4 Stand-alone Installation ......................................................................17

3.5 Rack Mounting and Wall mount ............................................................18

Appendix A: Precautions Appendix B: Troubleshooting

.....................................................................................15

..................................................................................19

......................................................................13

............................................................................20

Chapter 1. Product Introduction

Note

1.1 Package Contents

Check the contents of your package for following parts:

VF-402-T – Video over Fiber Media Converter / Transmitter x 1 VF-402-R – Video over Fiber Media Converter / Receiver x 1

5V / 2A Power Adapter x 2

User’s Manual x 1

If any of these pieces are missing or damaged, please contact your dealer immediately, if possible, retain the carton including the original packing material, and use them against to repack the product in case there is a need to return it to us for repair.

1.2 Product Description

Long Distances Analog Surveillance Transmission System

The analog cameras and DVRs are still applied mostly in traditional surveillance systems while the main stream turns to IP-Based surveillance gradually. To help the analog camera deployment in long distances to provide high video transmission quality and reliable signal, PLANET develops the Video over Fiber media converter

which successfully integrates the video signal and ber optic transmission in a

compact size mini box. The CCTV over Fiber media converter enables the videos to be delivered in high quality up to 20km long distance by the intelligent encoding / decoding technology. It is ideal for extending the distance and signal conversion by

transmitting the Video and data over the ber-optic cable.

Fiber Optic Communication for VIDEO and SERIAL DATA

This Video over Fiber Converter kit consists of a Video Transmitter and a Video Receiver:

VF-402-T: l 4-channel Video over Fiber Transmitter VF-402-R: l 4-channel Video over Fiber Receiver

Fiber-optic transmission system

This Video over Fiber Converter kit consists of a Video Tr ansmitter, VF-402- T, and a Video Receiver, VF-402-R (Figure 1).

It is a digital ber-optic transmission system which brings customer a cost-effective

solution for transmission of 4 channel uncompressed digital video and 1 reverse

RS-485 async-data over one single ber cable (Figure 2). It is an adjustment

free device while providing high quality and real-time video transmission. Support 20 KM long distance data rate. The system can be widely used in Intelligent

Transportation Systems (ITS), Trafc Surveillance, security monitoring, automation

control, intelligent residential districts and so on.

VF-402-T

Transmitter

Analog Camera

VF-402-R

Receiver

DVR / Monitor

Up to 20km

Fiber-optic Wire

Video Line

Video

Video Video

Figure 1 Standard Connection

Speed Dome

DVR / Monitor

Control Keyboard

|O|O|

Up to 20km

VF-402-T

Transmitter

VF-402-R

Receiver

Serial Line (RS-485)

|O|O|

Fiber-optic Wire

Video Line

Video

Data

Video

Figure 2 Data Control

Industrial monitoring systems

Industrial level super wide temperature range -25 to 75 Degree C, applicable to lots kinds of environment, also support hot plug, VF-402-KIT, 4 channel video adopts

advanced international no compression full digital error correction and gigabit ber optical transmission technology to fulll VF-402-KIT without distortion from longdistance in high quality through one ber. This series of optical transceiver is of

stable performance and clear graphics. This product is of high stability, can observe working condition visually with LED, support independent type and rack-mounted

structure, simple to operate, no eld adjustment need, applicable to different

working environment.

Control Center

VF-402-T

Transmitter

VF-402-R

Receiver

Fiber-optic Wire

VGA

VGA Line

Video Line

Video

DVR

Video

VGA

Up to 20km

1.3 Application

The VF-402-KIT consists of 4 channel video over ber optical transceiver and

receiver to transmit video and RS-485 signal through a reliable single mode

/ single ber link. It is an ideal cost-effective solution for surveillance system

that requires high display quality and high performance signal transmission over long distances. The VF-402-KIT can be installed easily and plug and play; that

means the operator does not need to congure the pair of the video over ber

transmission in advance.

FactoryTrain Station

Control Center

Residential

Analog Camera

Video Video

Analog Camera

DVR Control Keyboard

Speed DomeLong Distance IR

Analog Camera

Video

Video Video

Analog Camera

Video Video Video

Video

Video Video

Fiber-optic Wire

RS-485

Video Line

Video

RS-485

VF-402-R

Receiver

VF-402-T

Transmitter

VF-402-T

Transmitter

VF-402-T

Transmitter

IR Dome

Mini Dome

Analog Camera

RS-485

T ypical Applications

Intelligent Transportation Systems (ITS) l

Toll Collection

Trafc Surveillance

Air Trafc Management (ATM)

Rail Signaling

Perimeter Alarms and Area Monitors

Telemedicine and Teleconference Industrial Surveillance

Intelligent Building CCTV network

1.4 Product Features

20km long distance data transmission l

Fiber optic transmission of four video signals on one ber with RS485 data

signals which may be one way with the video or optionally duplex

Status indication for power supply, optical signal and video

High-Speed synchronous digital transmission technology No electromagnetic interference, radio frequency interference and ground current

Safe transmission guaranteed under poor electromagnetic environment

Maximum tolerable link loss for single mode single ber is 18db

Video bandwidth of 6.5 MHz, SNR>63dB

Industrial level super wide temperature range -25 to 75 Degree C

1.5 ProductSpecication

Model VF-402-T VF-402-R

Video Characteristic Video Channel 4 channel Bi-direction Video Connector BNC Video Input/Output Impedance 75ohm / unbalanced interface Video Input/Output Voltage 1.0 Vpp / Typical peak-peak value Video Bandwidth 5Hz to 6.5MHz

Video Digital Bit Width 8/10 bit Differential Gain (DG) <1.3% (Typical Value) Differential Phase (DP) <1.3° (Typical Value) SNR Weighted >63dB (Typical Value) Data Interface Data Channel 4 channel Physical Protocol RS-485 Operation Mode Simplex Data Connector 4 Pin terminal block with screw clamps Data Rate DC-150Kbps Data Distance RS-485: 0-20km BPS 0-115.2Kbps Bit Error Rate (BER) <10

-9

Optical Interface Optical Connector FC Fiber Type Single-mode, single ber Distance 20km for single mode

Optical Wav elength

T r ansmitter couple power

TX: 1310nm RX: 1550nm

Max. : 4dBm Min.

: -4dBm

TX: 1550nm RX: 1310nm

Receive Sensitivity -26dBm Link budget From 22dB to 30dB at 1310nm or 1550nm Cable 9/125μm single-mode cable

Hardware Specication

• One Power

LED Indicators

• One for Video - Green, Link

• One for Fiber Optic - Green, Link

Dimension (W x D x H) 110 x 174 x 47 mm Weight 560g

Power Requirement

Chassis Current Consumption

DC 5V / 2A AC 90~264V, 50~60HZ

0.75Amp for 4 channel video and 1 channel

data Mechanical Metal Standards Conformance Regulation Compliance FCC Part 15 Class A, CE

Environment

POWER

GND

LNKPWR

OPT

V2 V3 V4

110mm

47mm

110mm

133mm

174mm

27mm102mm

14mm

122mm

Operating

Storage

1.6 Dimension of Installing

Temperature: -25 ~ 75 Degree C

Relative Humidity: 0 ~ 95% (non-condensing)

Temperature: -40 ~ 85 Degree C

Relative Humidity: 5 ~ 95% (non-condensing)

Chapter 2. Hardware Description

LNKPWR

OPT

V2 V3 V4

2.1 Panel Overview

■ Front Panel:

■ Video interface

Item Description

VIDEO/V1…V4 Video input interface

■ Fiber interface

Item Description

Fiber interface (Warning: In case of damage to eyesight, Do not

FIBER/OPT

look directly into interface on electrify state). For Optical transceiver B type, this interface is empty, wiring out from the rear panel.

■LED denition

PWR: Power indicators. When power on, both PWR in “UP” and “DOWN” are ON. LNK: Optical link Indicator(After connecting ber, the indicator is green when

optical signal is detected; Unplug ber or no optical detected, light is out.)

V1~V4:

Video indicator (the indicator is green when video signal is detected; light

is out when there is no video signal).

■ Rear Panel:

POWER

GND

Power Notice

There is a power interface and power indicator on the rear panel, both PWR is ON

when power on. FIBER is ber interface; the description of each is as follows:

■ Power Supply

Power supply…

Input AC 90~264V, 50~60HZ Output 5V / 2A

1. The device is a power-required device, it means, it will not work till it is powered. If your networks should active all the time, please consider using UPS (Uninterrupted Power Supply) for your device. It will prevent you from network data loss or network downtime.

2. In some area, installing a surge suppression device may also help to protect your converter from being damaged by unregulated surge or current to the converter or the power adapter.

Chapter 3. Installation

This section describes how to install your VF-402-KIT Video over Fiber and make connections to the converter. Please read the following topics and perform the procedures in the order being presented. The hardware installation of PLANET

VF-402-KIT Video over Fiber Converter do not need software conguration. To

install your VF-402-KIT on a desktop or shelf, simply complete the following steps.

3.1 Limitation

The Video over Fiber Converter does not require any software conguration. Users

can immediately use any feature of this product simply by attached the cables

and plug power on. There is some key limitation on the video over ber converter.

Please check the following items: The device is used for Point-to-Point connection only (transmitter to receiver) and

allows video and data work on the same optical ber patch cord.

The BNC connector and supports 75 ohm cable. The distance will change by the quality of coaxial cables.

3.2 Preparation before Installing

In order to ensure your normal use, please make sure that you are using the right optical path, right signal, power grounding is good, and the environment meets the requirement. We guarantee all of our products are subject to strict test and aging,

and we simulate eld environment operation tests. Please contact us if there is any

problem. (1) Please carefully read the user manual of the product before installing. (2) Please carefully read the safety instructions. (3) Optical transceiver equipment shall not be disassembled by anyone without

authorization.

(4) Check the product model tag stuck outside the cabinet (T for transmitter, R for

receiver) to prevent incorrect installation.

(5) Optical transmitter is the transmitting part, its function is converting the video,

audio and data, switching value, Ethernet, etc into optical signals and then

transmitting through ber. Therefore, the device connect this type of optical

transmitter can be cradle head with cameras.

(6) Optical receiver is the receiving part, its function is converting the video, audio

and data, switching value, Ethernet, etc into electrical signals. Therefore, the device connect this type of optical receiver can be displayer or matrix.

(7) The relation of the video of optical transmitter and optical receiver is

one-to-one, which means V1~V4 of optical transmitter is one-to-one to V1~V4 of optical receiver.

3.3 Order for installation

(1) Connect the interface of optical transmitter with camera or speed dome. Then

connect the optical ber and the power supply.

(2) Connect the interface of optical receiver with video interface, monitor, video

matrix and displayer. Then connect the optical ber and the power supply.

(3) Insert the power supply according to the conguration of device, correctly

access peripheral attachment. Check optical ber, data cable, video cable,

and etc. on the basis of wiring diagram (accompanied with each set of optical transceiver) of optical transceiver.

(4) After all the connection and passing inspection, power on to see if device run

normally .

(5) Please install the lightning protection facilities and make sure the ground

connection is good when installing this device in the open air.

3.4 Stand-alone Installation

To install a VF-402-T / VF-402-R stand-alone, on a desktop or shelf, simply complete the following steps:

Step 1: Turn off the power of the analog camera / monitor to which the VF-402-T

/ VF-402-R will be attached.

Step 2: VF-402-T (Transmitter): Connect coaxial cable from analog camera to

Video BNC port of the VF-402-T.

Step 3: Attach FC single mode ber cable from the VF-402-T to VF-402-R in the

remote side.

Step 4: VF-402-R (Receiver): Connect coaxial cable from monitor / DVR to Video

BNC port of the VF-402-R.

Step 5: Connect the 5V DC power adapter to the VF-402-T / VF-402-R and verify

that the Power LED lights up.

Step 6: Turn on the power of the analog camera / monitor; the VIDEO LED

(Green) should light when all cables are attached.

Speed Dome

DVR / Monitor

Control Keyboard

|O|O|

Up to 20km

VF-402-T

Transmitter

VF-402-R

Receiver

Serial Line (RS-485)

|O|O|

Fiber-optic Wire

Video Line

Video

Figure 3-2 VF-402-T / VF-402-R stand alone installation

3.5 Rack Mounting and Wall mount

Rack Mount: Check device is tightly on the track

Wall Mount: Easier to put device on the wall with screws

Appendix A: Precautions

(1) Insert ber rightly into the ber interface; avoid breaking off ber because of

applying too much force. The rolling diameter shall not be too short (not less

than 20CM). (2) Fasten the retaining screw after connecting terminal blocks. (3) Do not remove the dust cap before installation, in order to avoid dirt and other

things getting into port, increasing the loss of optical signal and affecting the

transmission quality. (4) Notice optical transceiver matching when installing device to avoid cannot work

because of different optical power, data interface and transmission distance.

Pay attention to the differences of transmitter and receiver. (5) Data interface is terminal block. To ensure good contact, it requires inserting

interface after tinning. Please adopt stranded and shielded copper core of good

quality , such as Belden, etc.

Appendix B: Troubleshooting

Question Answer or Resolution

Power supply indicator is OFF

Abnormal video data

Irregular horizontal grain or beating video images

All indicators are off

Video indicator of

optical receiver ashes

Video indicator of optical transmitter OFF

Snowakes emerge

in output video of receiver

Check if the power plug is loose and the fuse wire of chassis.

Check if optical output power is normal and in the range of receiving sensitivity.

Incorrect video input synchronization, check if the grounding electrical level is equal, especially the grounding electrical level of the power of optical transceiver and input & output device; check the connection of video lines and if the input signal complies with standard.

Check if the power adapter works normally, if modules completed, insert the right slots.

Receiver not receiving the right optical signal; check if the link loss rate is normal. The rolling diameter is too short(less than 20CM); impurities on ceramic interface (gently clean it with alcoholic cotton).

Optical transceiver not receiving video signal, need to check the video input.

Bit error in transmission; check if the link loss is too much, The rolling diameter shall not be too short (not less than 20CM), unstable transmission because of operating the temperature of environment is too high.

Abnormal data

Check is data protocol is right (if using 232 transmitting 485, etc.), if the transmitting direction is right (forward, backward or bidirectional), if connecting right (data is positive or negative, transmitting or receiving), if the data input is right.

PLANET VF-402-KIT User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual