Planet POE-150-95 User Manual

1. Package Contents

3.ProductSpecications

4. Product Outlook

5. Hardware Installation

Thank you for purchasing PLANET POE-175-95 Single-port
10/100/1000Mbps 802.3bt PoE++ Injector.

Please unpack the box of the device carefully, and the box should
contain the following items:

802.3bt PoE injector x 1 User’s manual x 1

AC power cord x 1

If any item is found missing or damaged, please contact your local
reseller for replacement.

Product POE-175-95

Hardware Specications

Input Port 1 x RJ45 STP Data In

Interface

Output Port 1 x RJ45 STP PoE (Data + Power) Out

AC Socket 1 x AC input socket

Twisted-pair cable up to 100 meters
(328ft)*

Network Cable

10BASE-T: 4-pair UTP Cat. 3, 4, 5, 5e, 6
100BASE-TX: 4-pair UTP Cat. 5, 5e, 6
1000BASE-T: 4-pair UTP Cat. 5e, 6

PWR x 1 (Green)

LED Indicators

PoE-in-Use x 1 (Green)
PoE Usage x 3 (Green)

Data Rate 10/100/1000Mbps

Dimensions
(W x D x H)

170 x 100 x 40 mm

Weight 480g

Unit Output Voltage DC 54V

Power Requirements AC 100-240V, 1.2A max.

Power Consumption 120 watts max.

No. of devices that can
be powered

1

Power over Ethernet

PoE Standard IEEE 802.3at/bt PSE

Front View

in-Use

PoE-

PWR 90W

60W

30W

EthernetEthernet+DC

10/100/1000T

802.3bt PoE++ Injector

POE-175-95

100.00

40.00

Side View

Top View

170.00

Side View

Bottom View

90.8

Figure 1: Dimensions

The following section describes the hardware features of the
POE-175-95. Before connecting any network device to it, please
read this chapter carefully.

Rear View

5.1 Before Installation

Before your installation, it is recommended to check your network
environment. If there is any IEEE 802.3bt device that needs to be
powered on and works normally, the POE-175-95 provides you with
a way out to supply power to this Ethernet device conveniently and
easily.

It is equipped with an AC power cord with 100-240V AC input and
injects DC 54V power into the pin of the twisted-pair cable (pair
1/2 [-], 3/6 [+] and pair 4/5 [+], 7/8 [-]).

5.2 POE-175-95 Installation

1. Connect the AC power cord to the “AC slot” of the POE-175-95;
the “PWR” LED will be steadily on.

2. Connect a standard Ethernet cable from an Ethernet switch or
PC workstation to the “Ethernet” port of the POE-175-95.

3. Connect the long cable to the “Ethernet+DC” port.

Unit : mm

- 1 -

2. Product Features

 Interface

 2 RJ45 interfaces

 1-port Data input

 1-port Data + Power output

 1 AC 100-240V input power socket

 Power over Ethernet

 Complies with IEEE 802.3at/bt PoE end-span/mid-span PSE

 Supports PoE power up to 95 watts for PoE port

 Auto-detection of PoE IEEE 802.3at/bt devices that may be

damaged by incorrect installation

 Monitor the status of the total PoE usage in real time

 Remote power feeding up to 100m

 Hardware

 All-in-one compact size design

 Internal power supply

 LED indicators for Power LED, PoE Usage LED and PoE-in-Use

- 3 -

PoE Power Output
Budget

PoE Power Output

DC 54V / 95-watt PoE via 4-pair

Max. 90W@1 m cable
Max. 73W@100 m cable

PoE Power Supply Type End-span + Mid-span

Power Pin Assignment

Pair 1 End-span: 1/2 (-), 3/6 (+)
Pair 2 Mid-span: 4/5 (+), 7/8 (-)

Standards Conformance

IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast Ethernet
IEEE 802.3ab 1000BASE-T Gigabit

Standards Compliance

Ethernet
IEEE 802.3bt 4-pair Power over Ethernet
Type 4
IEEE 802.3at Power over Ethernet Plus

Regulatory Compliance FCC Part 15 Class A, CE

Environment

Operating Temperature 0 ~ 50 degrees C

Storage Temperature -10 ~ 70 degrees C

Operating Humidity

Storage Humidity

5 ~ 90%, relative humidity,
non-condensing

5 ~ 90%, relative humidity,
non-condensing

1. As IEEE 802.3bt device provides high power, please
use high-quality network cable and RJ45 connector.

Caution

2. The maximum PoE output power depends on the
cable length and the quality of cable.

- 5 -

LED Indicators:

LED Color Function

PWR Green

PoE-in-Use Green

PoE Usage Green

Lights to indicate the 802.3bt PoE injector
has power.

Lights to indicate the device is providing PoE
power.
Blinks to indicate that the system is
abnormal.

PoE Usage LED can monitor the status of
the power usage.

30W:

1. O to indicate the PoE usage is less than

14W.

2. Blinks to indicate that the PoE usage is
around 15W to 29W.

3. Lights to indicate the PoE usage is around
30W to 44W.

60W:

1. Blinks to indicate that the PoE usage is
around 45W to 59W.

2. Lights to indicate the PoE usage is around
60W to 74W.

90W:

1. Blinks to indicate that the PoE usage is
around 75W to 89W.

2. Lights to indicate the PoE usage is at the
maximum.

- 7 -

4. Due to the capability of IEEE 802.3at/bt Power over Ethernet,
the POE-175-95 can directly connect with any IEEE 802.3at/
bt-compliant end-nodes, such as PTZ (pan, tilt, zoom) network
cameras, color touch screen Voice over IP (VoIP) telephones and
multi-channel wireless LAN access points

100 meters

Ethernet Switch

95 watts

Power

Data

Power

POE-175-95

802.3bt PoE Injector

Data

PoE

PoE PTZ

IP Camera

1000BASE- T UTP

PoE

1000BASE- T UTP with PoE

Figure 2: Architecture of connected IEEE 802.3at/bt device

Once POE-175-95 detects the existence of an IEEE 802.3at/bt
device, the PoE-in-Use LED indicator will be steadily on to show it
is providing power.

1. According to IEEE 802.3at/bt Power over Ethernet,
the IPOE-175-95 will not inject power to the cable if
not connected to IEEE 802.3at/bt-compliant device.

Note

2. Depending on the length of cable, the PoE power
received by a PD is different.

- 2 -

- 4 -

- 6 -

- 8 -

5.3 POE-175-95 and POE-172S Installation

Taiwan

8

Jan., 2019

.

Place

Date

Legal Signature

1. Connect DC plug from “DC Out” of the POE-172S to a remote
device.

2. Connect the AC power cord to the “AC slot” of the POE-175-95;
the “PWR” LED will be steadily on.

3. Connect a standard Ethernet cable from an Ethernet switch or
PC workstation to the “Ethernet” port of the POE-175-95.

4. Connect a standard Ethernet cable from “Ethernet+DC” port
of the POE-175-95 to the “PoE In” port of the POE-172S. The

“30W” and “60W+” LED of the POE-172S and the “PoE-in­Use” LED of the POE-175-95 will light up continuously.

5. Connect a standard Ethernet cable from the “Ethernet” port of
the POE-172S to the remote Ethernet device.

6. The remote device will be turned on and connected.

100 meters

Ethernet Switch

95 watts

Data

Power

POE-175-95

802.3bt PoE Injector

Power

Data

PoE

POE-172S

Ultra PoE Splitter

PoE

DC

Data

DC

Power

12V/19V/24V

1000BASE- T UTP

1000BASE- T UTP with PoE

Power Line (DC)

Digital

Signage

100 meters 100 meters

Ethernet Switch

95 watts

Power

Data

Power

POE-175-95

802.3bt PoE Injector

Data

PoE

IPOE-E172

Gigabit PoE Extender

Power

PoE

Data

PoE

1000BASE- T UTP

1000BASE- T UTP with PoE

Figure 4: Architecture of connected POE-175-95 and IPOE-E172

Depending on the length of cable, the PoE power

Note

received by a PD is different.

PoE PTZ

IP Camera

Figure 3: Architecture of connected POE-175-95 and POE-172S

- 9 -

Please ensure the POE-172S output voltage is correct

Note

before applying power to the remote device.

5.4 POE-175-95 and IPOE-E172 Installation

1. Connect the AC power cord to the “AC slot” of the POE-175-95;
the “PWR” LED will be steadily on.

2. Connect a standard Ethernet cable from an Ethernet switch or
PC workstation to the “Ethernet" port of the POE-175-95.

3. Connect a standard Ethernet cable from the “Ethernet+DC”
port of the POE-175-95 to the “PoE IN” port of the IPOE-E172.

4. The POE-175-95 delivers both Ethernet Data and PoE power over
UTP cable to the IPOE-E172 and the “PoE-in-Use” LED of the
POE-175-95 and the “PWR” LED of the IPOE-E172 will light up
continuously.

5. Connect the additional standard Ethernet cable that will be used
for connecting to the remote PD to the “PoE Out” port of IPOE­E172.

6. Once the IPOE-E172 detects the existence of an IEEE 802.3af/
at/bt device, the “PoE-in-Use” LED indicator will be steadily ON
to show it is providing power.

7. The “PoE Out" port of the IPOE-E172 is then transmitting data
and power simultaneously to the PD.

- 10 -

- 11 -

Customer Support

Thank you for purchasing PLANET products. You can browse

our online FAQ resource at the PLANET Web site rst to check if

it could solve your issue. If you need more support information,
please contact PLANET support team.

PLANET online FAQs:
http://www.planet.com.tw/en/support/faq?method=category&c1=2

Support team mail address:
[e-mail]

Copyright © PLANET Technology Corp. 2020
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.

- 12 - - 13 -

For the following equipment:

*Type of Product : Single-Port 10/100/1000Mbps 802.3bt PoE Injector

*Model Number : POE-175-95

* Produced by:

Manufacturer‘s Name : Planet Technology Corp.
Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan

is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive on
2014/30/EU and Low Voltage Directive 2014/35/EU.
For the evaluation regarding the EMC, the following standards were applied:

EN 55032 2015+AC:2016, CLASS A

EN 55024 2010+A1:2015
EN 62368-1 2014

Responsible for marking this declaration if the:

 Manufacturer  Authorized representative established within the EU

Authorized representative established within the EU (if applicable):

Company Name: Planet Technology Co rp.

Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan

Person responsible for making this declaration

Name, Surname Jonas Yang

Position / Title : Director

EC Declaration of Conformity

EN 61000-3-2 2014
EN 61000-3-3 2013

th

PLANET TECHNOLOGY CORPORATION

10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan Tel:[phone] Fax:[phone]

e-mail: [e-mail] http://www.planet.com.tw