1. Overview
Thank you for purchasing PLANET MFB family SFP
100Base-FX Fast Ethernet module. The MFB family SFP
Fast Ethernet module can install into PLANET Switch
products with 100Base-FX SFP interface. The distance
can be extended from 2km (MM) up to 60 kilometers
(Single-mode, LC).
3. Check List
Your MFB carton should contain the following items:
The MFB family SFP Fast Ethernet module
l
This user’s manual
l
If any item is missing or damaged, please consult the
dealer from whom you purchased you MFB family SFP
Fast Ethernet module.
4-2 1-Port 100Base-BX WDM SFP Modules
– MFB-FA20 / MFB-FB20
Features:
l
Comply with IEEE 802.3u Fast Ethernet standard
1 x 100Mbps ber port (Single LC ber connectors)
l
Plug and Play Installation
l
MFB-FA20 provides distance up to 20km over
l
9/125μm single mode ber cable
MFB-FB20 provides distance up to 20km over
l
9/125μm single mode ber cable
The MFB series single mode SFP transceivers provide the optical power budget
from 15 dB to 30dB. When shorter
distance of single-mode fiber cables is
used, you might need to insert an inline optical attenuator in the link to avoid
overloading the receiver:
5. Installing SFP Modules
5.1 Installing the SFP transceiver
The sections describe how to insert an SFP transceiver
into an SFP slot.
The SFP transceivers are hot-pluggable and hotswappable. You can plug-in and out the transceiver to/
from any SFP port without having to power down the
Switch/Media Converter. As the Figure -1 appears.
Figure 1 Plug-in the SFP transceiver
- 1 -
2. Model List
Your MFB family SFP Fast Ethernet module comes with
one of the following models.
Fast Ethernet SFP module List
Model Interface Fiber connector and distance
MFB-FX
MFB-F20
MFB-F40
MFB-F60
MFB-FA20
MFB-FB20
* Models with last two numbered characters indicate the
maximum distance in km.
SFP-Port
100Base-FX
Module
SFP-Port
100Base-FX
Module
SFP-Port
100Base-FX
Module
SFP-Port
100Base-FX
Module
SFP-Port
100Base-BX
Module
SFP-Port
100Base-BX
Module
LC, Multi-Mode (1310nm)
-2km
LC, Single Mode (1310nm)
– 20km
LC, Single Mode (1310nm)
– 40km
LC, Single Mode (1310nm)
– 60km
LC WDM, Single Mode
(TX:1310nm, RX:1550nm)
-20km
LC WDM, Single Mode
(TX:1550nm, RX:1310nm)
-20km
- 3 -
4. Introduction
4-1 1-Port 100Base-FX SFP Modules – MFBFX / MFB-F20 / MFB-F40 / MFB-F60
Features:
Comply with IEEE 802.3u Fast Ethernet standard
l
1 x 100Mbps ber port
l
Plug and Play Installation
l
MFB-FX provides distance up to 2km over 62.5/125μm
l
multi-mode ber cable
MFB-F20 provides distance up to 20km over 9/125μm
l
single mode ber cable
MFB-F40 provides distance up to 40km over 9/125μm
l
single mode ber cable
MFB-F60 provides distance up to 60km over 9/125μm
l
single mode ber cable
SFP Model
In-line
Optical
Attenuator
Optical power
budget
Fiber Cable Length
= 10 Km
15Km ≤ Fiber
Cable Length <
60Km
- 5 -
MFB-F20 MFB-F40 MFB-F60 MFB-FA20 MFB-FB20
15 dB 24 dB 30 dB 20 dB 20 dB
5 dB 10 dB 15 dB 5 dB 5 dB
2 dB 10 dB -- 2 dB 2 dB
- 7 -
Before connect the other switches, workstation or Media
Converter.
1. Make sure both side of the SFP transceiver are with
the same media type or WDM pair, for example:
100Base-FX to 100Base-FX, 100Base-BX20-U to
100Base-BX20-D.
2. Check the ber-optic cable type match the SFP trans
ceiver model.
To connect to MFB-FX SFP transceiver, use the
l
multi-mode ber cable- with one side must be male
duplex LC connector type.
To connect to MFB-F20/F40/F60/FA20/FB20 SFP
l
transceiver, use the single-mode ber cable-with
one side must be male duplex LC connector type.
Connect the ber cable
1. Attach the duplex LC connector on the network cable
into the SFP transceiver.
2. Connect the other end of the cable to a device –
switches with SFP installed, ber NIC on a workstation or a Media Converter.
3. Check the LNK/ACT LED of the SFP slot of the switch
/ converter. Ensure that the SFP transceiver is operating correctly.
4. Check the Link mode of the SFP port if the link failed.
Co works with some ber-NICs or Media Converters,
set the Link mode to “100 Force” is needed.
-
- 2 -
- 4 -
- 6 -
- 8 -
5.2 Remove the module
1. Make sure there is no network activity by consult
or check with the network administrator. Or through
the management interface of the switch/converter (if
available) to disable the port in advance.
2. Remove the Fiber Optic Cable gently.
3. Turn the handle of the MFB module to horizontal.
4. Pull out the module gently through the handle.
Figure-2 Pull Out the SFP transceiver
Never pull out the module without pull the
handle or the push bolts on the module.
Direct pull out the module with violent could
damage the module and SFP module slot of
the device.
- 9 -
APPENDIX A
A.1 Fiber Optical Cable Connection
Parameters
The wiring details are as below:
Fiber Optical patch Cables:
Standard Fiber Type Cable Specication
100Base-FX
(1310nm)
100Base-FX
(1310nm)
100Base-BX-U
(TX:1310/RX:1550)
100Base-BX-D
(TX:1550/RX:1310)
Multi-mode
Multi-mode
Single-mode 9/125μm
Single-mode 9/125μm
50/125μm or
62.5/125μm
50/125μm or
62.5/125μm
- 10 -