Page 1
Industrial 1-Port Coax/UTP Long Reach PoE+ 4-Port
10/100TX PoE Extender
LRP-104CET
User’s Manual
Page 2
Table of Contents
1. Package Contents ................................................................................. 3
2. Application Diagram .............................................................................. 4
2.1 Point to Multi-point ........................................................................ 4
2.1.1 LRP-101CH to LRP-104CET .................................................... 4
2.1.2 LRP-101UH to LRP-104CET ................................................... 5
2.2 Multi-Point to Multi-Point ................................................................ 6
2.2.1 LRP-822CS/LRP-1622CS to LRP-104CET ................................. 6
3. Hardware Introduction .......................................................................... 7
3.1 Physical Dimensions ....................................................................... 7
3.2 Front Panel ................................................................................... 8
3.3 The Upper Panel ............................................................................ 8
3.4 LED Indicators ............................................................................... 9
3.5 PoE DIP Switch Indication ..............................................................10
4. HardwareSpecications .......................................................................11
5. Installation Precautions ........................................................................15
5.1 Installation Precautions of Remote Power by Coaxial Cable ...............15
5.2. Installation Precautions of Remote Power by UTP Cable....................15
5.3 Installation Precautions of Local Power ...........................................16
5.4 Wiring the Fault Alarm Contact ......................................................17
6. Installation .........................................................................................18
6.1 Applications of LRP-101CH or LRP Switch with coaxial cable .............18
6.2 Applications of LRP-101U-KIT with UTP/Twisted-pair Cable ...............21
6.3 Applications of LRP Injector or LRP Switch powered
by External DC power supply .........................................................24
Appendix A: Networking Connection ...........................................................27
A.1 Switch’s RJ45 Pin Assignments .......................................................27
A.2 RJ45 Cable Pin Assignments ..........................................................27
Page 3
1. Package Contents
Thank you for purchasing PLANET Industrial 1-Port Long Reach PoE+
4-Port 10/100TX PoE Extender, LRP-104CET. In the following section, the
term “LRP Extender” means the LRP-104CET.
Open the box of the LRP Extender and carefully unpack it. The box should
contain the following items:
LRP Extender x 1 User’s Manual x 1
DIN Rail Kit x 1 Wall-mount Kit x 1
If any of these are missing or damaged, please contact your dealer
immediately; if possible, retain the carton including the original packing
material, and use them again to repack the product in case there is a need to
return it to us for repair.
3
Page 4
2. Application Diagram
PLANET Long Reach PoE solution is designed to extend IP Ethernet
transmission and inject power simultaneously into a remote 802.3af/at PoE
compliant powered device (PD) beyond the 100 meters distance limit of
Ethernet. The solution works in pairs for point to point and point to multipoint
connectivity.
The LRP-104CET supports two ways as power source to inject 802.3af/at PoE
to remote standard PDs (Powered Devices).
z Remote LRP Power from LRP Injector/switch over coaxial cable
z Local DC power from power supply through LRP-104CET’s terminal
block
In the following application topologies, users can nd the suitable way to
extend the distance and power on the remote PDs.
2.1 Point to Multi-point
Remote LRP Power through BNC/RJ45 with DC 56V input or Local Power with
External DC input (DC 24V~48V)
2.1.1 LRP-101CH to LRP-104CET
Remote LRP Power over Coaxial
110-240V AC
AC-to-DC Adapter
60W~120W/48~56V DC IN
Ethernet Switch
Cat5e/6
Long Reach Power over Ethernet
LRP-101CH
Long Reach PoE Injector
Power over Coaxial
LRP-104CET
Long Reach PoE Extender
Ext.
PWR
P1 P2 Fault
PoE
Power
Usage
10W 20W 30W 40W
OFF
Port PoE
12 3 4
ON
OFF
1
ON
OFF
2
ON
OFF
3
ON
OFF
4
PWR
LRP IN
LNK
Long Reach PoE
802.3af/802.3at PoE
1
2
Extender
3
4
ACTLNK
PoE In-use
LRP-104CET
PoE Power Budget
60 watts~120 watts (max.)
PoE
PoE
PoE
PoE
PoE IP Camera
4
Page 5
Local Power
110-240V AC
AC-to-DC Adapter
60W/48~56V DC IN
Long Reach Power over Ethernet
LRP-101CH
Long Reach PoE Injector
Ethernet Switch
Cat5e/6
2.1.2 LRP-101UH to LRP-104CET
Remote LRP Power over UTP
110-240V AC
AC-to-DC Adapter
60W~120W/48~56V DC IN
Ethernet Switch
Cat5e/6
Long Reach Power over Ethernet
LRP-101UH
Long Reach PoE Injector
Power over UTP
LRP-104CET
Long Reach PoE Extender
Ext.
PWR
P1 P2 Fault
PoE
Power
Usage
10W 20W 30W 40W
OFF
Port PoE
12 3 4
ON
OFF
1
ON
OFF
2
ON
OFF
3
ON
OFF
4
PWR
LRP IN
LNK
Long Reach PoE
802.3af/802.3at PoE
1
2
Extender
3
4
ACTLNK
PoE In-use
LRP-104CET
PoE Power Budget
120 watts (max.)
LRP-104CET
Long Reach PoE Extender
Ext.
P1 P2 Fault
PWR
PoE
Power
Usage
10W 20W 30W 40W
OFF
Port PoE
12 3 4
ON
OFF
1
ON
OFF
2
ON
OFF
3
ON
OFF
4
PWR
LRP IN
LNK
Long Reach PoE
1
2
Extender
3
4
ACTLNK
PoE In-use
LRP-104CET
PoE Power Budget
60 watts~120 watts (max.)
DC
PoE
PoE
PoE
PoE
802.3af/802.3at PoE
PoE
PoE
PoE
PoE
120W/24-48V DC
Power Supply
PoE IP Camera
PoE IP Camera
Local Power
110-240V AC
AC-to-DC Adapter
60W/48~56V DC IN
Ethernet Switch
Cat5e/6
Long Reach Power over Ethernet
LRP-101UH
Long Reach PoE Injector
LRP-104CET
Long Reach PoE Extender
Ext.
P1 P2 Fault
PWR
PoE
Power
Usage
10W 20W 30W 40W
OFF
Port PoE
12 3 4
ON
OFF
1
ON
OFF
2
ON
OFF
3
ON
OFF
4
PWR
LRP IN
LNK
Long Reach PoE
1
2
Extender
3
4
ACTLNK
PoE In-use
LRP-104CET
PoE Power Budget
DC
802.3af/802.3at PoE
PoE
PoE
PoE
PoE
120 watts (max.)
120W/24-48V DC
Power Supply
PoE IP Camera
5
Page 6
2.2 Multi-Point to Multi-Point
Remote power LRP Power through BNC with DC 56V input or Local Power with
External DC input (DC 24V~48V)
2.2.1 LRP-822CS/LRP-1622CS to LRP-104CET
Remote LRP Power
LRP-822CS
110-240V AC
Local Power
LRP-822CS
110-240V AC
6
Power over Coaxial
Power over Coaxial
Up to 400m
Up to 400m
Coaxial
Up to 400m
Coaxial
Up to 400m
LRP-104CET
Long Reach PoE Extender
Ext.
PWR
P1 P2 Fault
PoE
Power
Usage
10W 20W 30W 40W
OFF
Port PoE
1 2 3 4
ON
OFF
1
ON
OFF
2
ON
OFF
3
ON
OFF
4
PWR
LRP IN
LNK
Long Reach PoE
1
2
Extender
3
4
ACTLNK
PoE In-use
LRP-104CET
Ext.
PWR
P1 P2 Fault
PoE
Power
Usage
10W 20W 30W 40W
OFF
Port PoE
1 2 3 4
ON
OFF
1
ON
OFF
2
ON
OFF
3
ON
OFF
4
PWR
LRP IN
LNK
Long Reach PoE
1
2
Extender
3
4
ACTLNK
PoE In-use
LRP-104CET
LRP-104CET
Long Reach PoE Extender
Ext.
PWR
P1 P2 Fault
PoE
Power
Usage
10W 20W 30W 40W
OFF
Port PoE
1 2 3 4
ON
OFF
1
ON
OFF
2
ON
OFF
3
ON
OFF
4
PWR
LRP IN
LNK
Long Reach PoE
1
2
Extender
3
4
ACTLNK
PoE In-use
LRP-104CET
Ext.
PWR
P1 P2 Fault
PoE
Power
Usage
10W 20W 30W 40W
OFF
Port PoE
1 2 3 4
ON
OFF
1
ON
OFF
2
ON
OFF
3
ON
OFF
4
PWR
LRP IN
LNK
Long Reach PoE
1
2
Extender
3
4
ACTLNK
PoE In-use
LRP-104CET
802.3at PoE+
UTP
PoE
PoE
PoE
PoE
UTP
PoE
PoE
PoE
PoE
802.3at PoE+
DC
UTP
PoE
PoE
PoE
PoE
DC
UTP
PoE
PoE
PoE
PoE
PoE
IP Camera
PoE Power Budget
20 watts (max.)
PoE
IP Camera
120W/24-48V DC
Power Supply
PoE Power Budget
120 watts (max.)
120W/24-48V DC
Power Supply
PoE Power Budget
120 watts (max.)
Page 7
3. Hardware Introduction
3.1 Physical Dimensions
LRP-104CET LRP Extender dimensions (W x D x H): 135 x 87.8 x 56mm
Top View
DC1 DC2Fault
+
+
Input DC 24-4 8V
DIN-Rail Kit
Side View
Rear View
Front View
P1 P2 Fault
10W 20W 30W 40W
OFF
1 2 3 4
PWR
LNK
Ext.
PWR
Port PoE
OFF
1
OFF
2
OFF
3
OFF
4
LRP IN
1
2
3
4
PoE In-use
LRP-104CET
Power
Usage
PoE
ON
ON
ON
ON
Long Reach PoE
Extender
ACTLNK
Mounting Kit
Mounting Kit
Side View
Dimensions ( unit = mm )
Figure 3-1: shows the front panel of LRP Extender
7
Page 8
3.2 Front Panel
The front panel of the LRP Extender consists of 1BNC female/RJ45 connector
and 4 10/100BASE-TX RJ45 ports. The LED Indicators are also located on the
RJ45 ports of LRP-104CET
Ext.
P1 P2 Fault
PWR
PoE
Power
Port PoE
OFF
1
2
OFF
3
OFF
4
OFF
Usage
ON
ON
ON
ON
10W 20W 30W 40W
OFF
1 2 3 4
PWR
LNK
LRP IN
Long Reach PoE
1
2
Extender
3
4
ACTLNK
PoE In-use
LRP-104CET
Figure 3-2: LRP-104CET Front Panel
3.3 The Upper Panel
The upper panel of the LRP Extender consists of one terminal block connector
within two DC power inputs.
1 2 3 4 5 6
+
DC1 DC2Fault
+
Input DC 24-48V
Figure 3-3: LRP Extender Upper Panel
8
Page 9
3.4 LED Indicators
External Power Supply
LED Color Function
P1 Green Lights to indicate power 1 has power.
P2 Green Lights to indicate power 2 has power.
FAULT Red
PoE Usage
LED Color Function
10W Green Lights to indicate thepowerusageis ≥ 10W.
20W Green Lights to indicate thepowerusageis ≥ 20W.
30W Green Lights to indicate thepowerusageis ≥ 30W.
40W Green Lights to indicate thepowerusageis ≥ 40W.
LRP Interface
LED Color Function
PWR Green Lights to indicate the power is on.
LNK Green
Lights to indicate either power 1 or power 2 has no
power.
Lights to indicate that the Coaxial/UTP link is
established.
Off: indicates that the Coaxial/UTP link is down.
RJ45 10/100 BASE-TX Interface
LED Color Function
PoE
In-Use
10/100
LNK/ACT
Orange
Green
Lights to indicate the RJ45 port is providing PoE power.
Lights to indicate the link through that port is success-
fully established at 10/100Mbps.
Blinks to indicate that the port is actively sending or
receiving data.
Off: indicates that the port is link down.
9
Page 10
3.5 PoE DIP Switch Indication
The LRP Extender provides an adjustable switch that can be used to control
the operation of the PoE output.
Port 1
Port 2
Port 3
Port 4
Note
Caution
OFF
1 2 3 4
ON (default) Port-1 PoE Enable
OFF Port-1 PoE Disable
ON (default) Port-2 PoE Enable
OFF Port-2 PoE Disable
ON (default) Port-3 PoE Enable
OFF Port-3 PoE Disable
ON (default) Port-4 PoE Enable
OFF Port-4 PoE Disable
For example, if administrator wants to stop remote Powered
device of port1, simply turn the switch OFF to stop the output
power.
When you turn off the PoE function of any ports, per port output
will not enhance the output capacity.
Port PoE
OFF
1
2
OFF
3
OFF
4
OFF
ON
ON
ON
ON
10
Page 11
4.HardwareSpecications
Model LRP-104CET
HardwareSpecications
Four 10/100BASE-TX RJ45 auto-MDI/
MDI-X
Four ports with 802.3at/af PoE injector
function with Port-1 to Port-4
Four DIP switches to control PoE output
on or off with Port-1 to Port-4
IEEE 802.3at Power over Ethernet Plus/
PSE
52V DC, PoE output depends on LRP
Injector or LRP Switch
52V DC, 25-watt per port
(External DC input)
Ethernet : 10BASE-T: 2-pair UTP Cat.3, 4
and 5
Ethernet : 100BASE-TX: 2-pair UTP Cat.5,
5e and 6
1522 bytes
One BNC female
Long Reach PoE
over Coaxial PD
(Powered Device)
BNC center pole:
DC+
BNC shield: DC-
Ethernet
Interface
Long Reach
PoE Interface
Copper Ports
PoE Injector Ports
Functionality
PoE Standards
Compliance
PoE Type End-span
PoE Power output
Cabling
Maximum Distance 100m
Maximum Frame
size
Connectivity
Power Input 44~56V DC
Power Pin
Assignment
One RJ45 connector
Long Reach PoE
over UTP PD
(Powered Device)
RJ45 Pin 1, 3, 5, 7:
VCC+
RJ45 Pin 2, 4, 6, 8:
VCC-
11
Page 12
Cabling
Coaxial cable: 75
ohm
RG-6/U cable, less
than12Ω/1000ft
RG-59/U cable, less
than30Ω/1000ft.
Cat. 3, 4, 5, 5e UTP
cable (100 meters,
max.)
EIA/TIA-568
100-ohm STP (100
meters, max.)
Long Reach
PoE Interface
Max. 200m with
PoE+ output (656ft.)
Max. 400m
Maximum Distance
Long Reach Ethernet
Standard
Modulation Type Wavelet-OFDM
Security 128-bit AES encryption
Frequency Band 2~28 MHz
Encryption AES 128-bit
LRP Compatibility
with PoE output
(1,312ft.)
Max. 1000m
without PoE output
(3,280ft.)
IEEE 1901
With power over
coaxial input:
• LRP-101CH –
1-Port LRP
Injector
• LRP-822CS –
8-Port LRP over
Coax Switch
• LRP-1622CS –
16-Port LRP over
Coax Switch
Max. 100m with
PoE+ output
(328ft.)
Max. 400m with PoE
output (1,312ft.)
With power over
UTP input:
• LRP-101UH –
1-Port LRP
Injector
12
Page 13
3 x LED for External
power supply:
4 x LED for PoE
LED Indicator
Installation DIN rail kit and wall mount kit
Dimensions
(W x D x H)
Weight 644g
Power
Requirements
Power
Consumption/
Dissipation
Alarm
Enclosure Aluminum metal case
Standards Conformance
Standards
Compliance
Regulatory
Compliance
Stability
Testing
Usage:
2 x LED for Long
Reach PoE In:
2 x LED for each
RJ45 interface
(Port-1 and Port-4)
135 x 87.8 x 56 mm
44~56V DC power over coaxial input
DC 24~48V, redundant power with polarity reverses protection
function
130watts/446BTU (Ethernet with PoE Full Loading)
One relay output for power failure. Alarm relay current carry
ability: 1A @ 24V DC
IEEE 802.3 Ethernet/10BASE-T
IEEE 802.3u Fast Ethernet/100BASE-TX
IEEE 802.3x Full-Duplex Flow Control
IEEE 802.3at Power over Ethernet Plus
FCC Part 15 Class A, CE
IEC60068-2-32 (free fall)
IEC60068-2-27 (anti-shock)
IEC60068-2-6 (anti-vibration)
Green: DC Power 1
Green: DC Power 2
Red: Power Fault
Green: 10W/20W/30W/40W
Green: PWR
Green: LNK
Green: 10/100Mbps LNK/ACT
Orange: PoE-in-use
13
Page 14
Environment
Temperature
Humidity
Performance
Coaxial
Performance
UTP
Performance
* As there are various resistance values in the category of RG-59/U or RG-6/U
cable, the actual data rate will vary on the quality of the copper wire and
environment factors.
** Depending on what the DC/PoE Power Input and the length of coaxial
cable are.
Operating: -20~70 degrees C
Storage: -20~70 degrees C
Operating: 5~95% (non-condensing)
Storage: 5~95% (non-condensing)
802.3af/at PoE Total Output Capability
Data
Distance
200m 88/88 Mbps 21.5W 18W/19W 120W
400m 85/86 Mbps 20W 14W/16W 120W
600m 66/67 Mbps 19W 10W/12W 120W
800m 48/57 Mbps 11W 7W/8W 120W
1000m 44/57 Mbps 5W 120W
Distance
100m 80/85Mbps 21.2W 120W
200m 63/75Mbps 21W 120W
300m 33/60Mbps 20W 120W
400m 5/10Mbps 14W 120W
rate(Upload/
Download)
Data rate
(Upload/
Download)
Remote
LRP power
through
BNC
W/56VDC
IN
802.3af/at PoEtotal Output Capability
Remote LRP power
through RJ45
W/56VDC IN
Remote LRP
power by
LRP-822CS/
LRP-1622CS
Local DC power
through terminal
block
Local DC
power
through
terminal
block
14
Page 15
5. Installation Precautions
The LRP-104CET supports two ways as power source to inject 802.3af/at PoE
to remote standard PDs.
z Remote LRP Power from LRP Injector/switch over coaxial/UTP cable
z Local DC power from power supply through LRP-104CET’s terminal block
5.1 Installation Precautions of Remote Power by Coaxial Cable
When installing LRP PoE over coaxial injector, it only can work with PLANET
LRP Extender, the LRP-104CET or LRP-101CE. Please conrm that other
non-PoE equipment is not connected with the coaxial cable. When you connect
the coaxial cable with coax-LAN converter, CCTV camera, etc, it might cause
other equipment to damage.
After the power over coaxial injector is enabled, the center pin
of the coaxial cable is with electricity. Please do not touch the
center pin.
the device.
careful before plugging into
Please be reminded that the cable con
contains electric power. Please be
Caution
Warning:
This side of connector
Do Not Touch
the Center Pin
All PLANET power over coaxial injectors or switches have the
Warning Sticker, including LRP-101CH, LRP-822CS and LRP-
Note
1622CS.
5.2. Installation Precautions of Remote Power by UTP Cable
When installing LRP PoE over UTP injector, it only can work with PLANET LRP
Extender, the LRP-104CET or LRP-101UE. Please conrm that other non-PoE
equipment is not connected with the UTP cable. If connected with standard
Ethernet equipment, it might cause damage to the equipment.
15
Page 16
5.3 Installation Precautions of Local Power
Caution
Installation of LRP injector or LRP switch. If you need to increase the PoE
power budget of the LRP-104CET, you must use an external DC power supply.
The 6-contact terminal block connector on the upper panel of LRP Extender
is used for two DC redundant power inputs. Please follow the steps below to
insert the power wire.
When the user is connected with an external power supply,
the LRP-104CET will give priority to external power supply, LRP
Note
1. Insert positive and negative DC power wires into contacts 1 and 2 for
POWER 1, or 5 and 6 for POWER 2.
Injector or LRP Switch where data is transmitted to the LRP104CET.
When performing any of the procedures like inserting the wires
or tightening the wire-clamp screws, make sure the power is
OFF to prevent from getting an electric shock.
1 2 3 4 5 6
+
DC1 DC2Fault
+
Input DC 24-48V
2. Tighten the wire-clamp screws for preventing the wires from loosening.
1 2 3 4 5 6
Power 1 Fault Power 2
- + - +
16
Page 17
1. The wire gauge for the terminal block should be in the range
between 12 and 24 AWG.
Note
2. The DC power input range is 24V ~ 48V DC.
5.4 Wiring the Fault Alarm Contact
The fault alarm contacts are in the middle of the terminal block connector as
the picture shows below. Inserting the wires, the LRP Extender will detect the
fault status of the power failure and then forms an open circuit. The following
illustration shows an application example for wiring the fault alarm contacts.
1 2 3 4 5 6
The Fault Alarm Contacts are
energized (CLOSE) for normal
Fault Alarm Contacts
1. The wire gauge for the terminal block should be in the range
between 12 and 24 AWG.
Note
2. Alarm relay circuit accepts up to 24V, max. 1A currents.
Fault
Insert the wires into the fault alarm contacts
operation and will OPEN when
failure occurs
17
Page 18
6. Installation
This section describes the functionalities of the LRP Extender’s components and
guides you to how to install it. Basic knowledge of networking is expected.
Please read this chapter completely before continuing.
Before installation, please consider the distance and watts
value demand for PD devices. The LRP-104CET output capacity
Note
Note
6.1 Applications of LRP-101CH or LRP Switch with coaxial cable
Type 1 One LRP-101CH with PoE power input and one LRP-104CET with PoE
The LRP Injector is powered via IEEE 802.3at/af PoE. An IEEE 802.3at/af
compliant PoE PD will automatically be powered by the LRP Extender via UTP.
and upload / download performance depends on the length of
coaxial cable and UTP cable.
When the remote PD’s total power consumption is higher than
LRP-104CET PoE power budget, the device will reboot and the
LED Indicators will flash continuously. Please remove UTP cables
of RJ45 ports to avoid the LRP-104CET to malfunction.
power output
Remote LRP Power
802.3af / 802.3at
PoE Switch
Functions
Power Input
Power Output
18
PoE
Long Reach Power over Ethernet
PoE
Cat5e/6
LRP-101CH
Long Reach PoE Injector
Power over Coaxial
LRP Injector LRP Extender
LRP-101CH LRP-104CET
RJ45 with 802.3at/af PoE
input
BNC with DC power over
coaxial output
LRP-104CET
Long Reach PoE Extender
Ext.
P1 P2 Fault
PWR
PoE
Power
Usage
10W 20W 30W 40W
OFF
Port PoE
12 3 4
ON
OFF
1
ON
OFF
2
ON
OFF
3
ON
OFF
4
PWR
LRP IN
LNK
Long Reach PoE
802.3af/802.3at PoE
1
2
3
4
LRP-104CET
PoE In-use
PoE
PoE
Extender
PoE
PoE
ACTLNK
PoE Power Budget
20 watts (max.)
PoE IP Camera
BNC with DC power over
coaxial input
RJ45 with 802.3at/af PoE
output
Page 19
Installation Instructions
Step 1. Connect the LRP Injector (LRP-101CH) and LRP Extender
(LRP-104CET) to ends of BNC terminated coaxial cable.
Stick the “Warning Sticker” on the coaxial cable.
Step 2. Connect Cat5/6 UTP cable to LRP-101CH and IEEE 802.3at compliant
PoE Switch or PoE Injector. If the PoE switch or PoE injector
is powered on already, then the PWR LED of LRP-101CH and
LRP-104CET should be lit up immediately.
Step 3. Connect Cat5/6 UTP cable to LRP-104CET and IEEE 802.3at/af
complied PoE IP camera or PoE Wireless AP.
The LRP-101CH accepts IEEE 802.3at equipment for optimal
power injection. The other non-standard PoE power devices may
Warning
Type 2 One LRP-101CH with 48~56V power adapter and one LRP-104CET
The LRP Injector is powered via the external power adapter. The IEEE 802.3at/
af compliant PoE PD will automatically be powered by the LRP Extender via
UTP.
cause the LRP-101CH to malfunction.
with PoE power output
Remote LRP Power over Coaxial
110-240V AC
AC-to-DC Adapter
60W~120W/48~56V DC IN
Ethernet Switch
Cat5e/6
Long Reach Power over Ethernet
LRP-101CH
Long Reach PoE Injector
Power over Coaxial
LRP-104CET
Long Reach PoE Extender
Ext.
PWR
P1 P2 Fault
PoE
Power
Usage
10W 20W 30W 40W
OFF
Port PoE
12 3 4
ON
OFF
1
ON
OFF
2
ON
OFF
3
ON
OFF
4
PWR
LRP IN
LNK
Long Reach PoE
802.3af/802.3at PoE
1
2
Extender
3
4
ACTLNK
PoE In-use
LRP-104CET
PoE Power Budget
60 watts~120 watts (max.)
PoE
PoE
PoE
PoE
PoE IP Camera
Functions
Power Input
Power Output
LRP Injector LRP Extender
LRP-101CH LRP-104CET
Power adapter with 48~56V DC in
The LRP-101CH accepts up to 120W
external power input
BNC with DC power over coaxial
output
BNC with DC power
over coaxial input
RJ45 with 802.3at/af
PoE output
19
Page 20
Installation Instructions
Step 1. Connect the LRP Injector (LRP-101CH) and LRP Extender
(LRP-104CET) to ends of BNC terminated coaxial cable.
Stick the “Warning Sticker” on the coaxial cable.
Step 2. Connect Cat5/6 UTP cable to LRP-101CH and non-PoE switch or
workstation.
Step 3. Connect 48~56V DC power adapter to LRP-101CH power socket,
then the PWR LED of LRP-101CH and LRP-104CET should be lit up
immediately.
Step 4. Connect Cat5/6 UTP cable to LRP-104CET and IEEE 802.3at/af
complied PoE IP camera or PoE Wireless AP.
1. PoE output capacity is based on different DC Power Input /
PoE Input.
2. The LRP-101CH has two power input options; only one mode
Note
Type 3 One LRP-822CS/LRP-1622CS with AC power input and one
The LRP Switch is powered via the AC power. The IEEE 802.3at/af compliant
PoE PD will automatically be powered by the LRP Extender via UTP.
is available at one time. PoE power input cannot be used if
power input of DC 52V or 56V is selected.
LRP-104CET with PoE power output
Remote LRP Power
110-240V AC
20
LRP-822CS
Power over Coaxial
Up to 400m
Up to 400m
LRP-104CET
Long Reach PoE Extender
Ext.
PWR
P1 P2 Fault
PoE
Power
Usage
10W 20W 30W 40W
OFF
Port PoE
1 2 3 4
ON
OFF
1
ON
OFF
2
ON
OFF
3
ON
OFF
4
PWR
LRP IN
LNK
Long Reach PoE
1
2
Extender
3
4
ACTLNK
PoE In-use
LRP-104CET
Ext.
PWR
P1 P2 Fault
PoE
Power
Usage
10W 20W 30W 40W
OFF
Port PoE
1 2 3 4
ON
OFF
1
ON
OFF
2
ON
OFF
3
ON
OFF
4
PWR
LRP IN
LNK
Long Reach PoE
1
2
Extender
3
4
ACTLNK
PoE In-use
LRP-104CET
802.3at PoE+
UTP
PoE
PoE
PoE
PoE
UTP
PoE
PoE
PoE
PoE
PoE
IP Camera
PoE Power Budget
20 watts (max.)
Page 21
Functions
Power Input
Power Output
Power cord with AC 100~240V,
50/60Hz, auto-sensing
BNC with DC power over coaxial
output
LRP Switch LRP Extender
LRP-822CS/LRP-1622CS LRP-104CET
BNC with DC power over
coaxial input
RJ45 with 802.3at/af PoE
output
Installation Instructions
Step 1. Connect the LRP Switch (LRP-822CS/LRP-1622CS) and LRP Extender
(LRP-104CET) to ends of BNC terminated coaxial cable.
Step 2. Connect 100~240V AC power cord to LRP Switch (LRP-822CS/
LRP-1622CS) power socket, then the PWR LED of LRP Switch
(LRP-822CS/LRP-1622CS) should be lit up immediately.
The LRP Managed Switch is congured DISABLED Long Reach PoE
function as default. So you must Enable Long Reach PoE function for
all LRP ports from WebUI.
Step 3. After enabling the LRP function of LRP Switch (LRP-822CS/
LRP-1622CS) from WebUI, the PWR LED of LRP-104CET should be lit
up immediately.
Step 4. Connect Cat5/6 UTP cable to LRP-104CET and IEEE 802.3at/af
complied PoE IP camera or PoE Wireless AP.
Additional advanced settings for the LRP Switch (LRP-822CS /
LRP-1622CS) can be downloaded from the PLANET website or
Note
contact the PLANET support team.
6.2 Applications of LRP-101U-KIT with UTP/Twisted-pair Cable
Type 1 LRP-101UH with PoE power input and LRP-104CET with PoE power
output
Remote LRP Power over UTP
PoE
Long Reach Power over Ethernet
PoE
Cat5e/6
LRP-101UH
802.3af / 802.3at
PoE Switch
Long Reach PoE Injector
Power over UTP
LRP-104CET
Long Reach PoE Extender
Ext.
P1 P2 Fault
PWR
PoE
Power
Usage
10W 20W 30W 40W
OFF
Port PoE
12 3 4
ON
OFF
1
ON
OFF
2
ON
OFF
3
ON
OFF
4
PWR
LRP IN
LNK
Long Reach PoE
1
2
Extender
3
4
ACTLNK
PoE In-use
LRP-104CET
PoE Power Budget
802.3af/802.3at PoE
PoE
PoE
PoE
PoE
20 watts (max.)
PoE IP Camera
21
Page 22
Functions
Power Input
Power Output
RJ45 with 802.3at/af PoE
input
UTP with DC power over UTP
output
LRP Injector LRP Extender
LRP-101UH LRP-104CET
UTP with DC power over UTP
input
RJ45 with 802.3at/af PoE
output
Installation Instructions
Step 1. Remove the “Danger – No Ethernet” label stuck on the RJ45 LRP
port of LRP-101UH.
Step 2. Connect the LRP Injector (LRP-101UH) and LRP Extender
(LRP-104CET) to ends of RJ45 terminated long UTP/twisted-pair
cable.
1. Please do not connect any Ethernet equipment to LRP
OUT Port of the LRP-101UH; otherwise, it will damage the
Ethernet equipment.
Warning
Step 3. Connect Cat5/6 UTP cable to LRP-101UH and IEEE 802.3at
Step 4. Connect Cat5/6 UTP cable to LRP-104CET and IEEE 802.3at/af
2. Please do not connect any Ethernet equipment to LRP IN Port
of the LRP-104CET; otherwise, it will damage the Ethernet
equipment.
compliant PoE Switch or PoE Injector. If the PoE switch or PoE
injector is powered on already, then the PWR LED of LRP-101UH and
LRP-104CET should be lit up accordingly.
complied PoE IP camera or PoE Wireless AP.
Warning
Note
22
The LRP-101UH accepts IEEE 802.3at equipment for optimal
power injection. The other non-standard PoE Power devices may
cause the LRP-101UH to malfunction.
As there are various resistance values in the category 5/5e
cable, the actual data rate will vary on the quality of the copper
wire and environmental factors.
Page 23
Type 2 LRP-101UH with 48~56V power adapter and LRP-104CET with PoE
power output
Remote LRP Power over UTP
110-240V AC
60W~120W/48~56V DC IN
Ethernet Switch
Functions
Power Input
AC-to-DC Adapter
Cat5e/6
Long Reach Power over Ethernet
LRP-101UH
Long Reach PoE Injector
Power over UTP
LRP Injector LRP Extender
LRP-101UH LRP-104CET
Power adapter with 48~56V DC in
The LRP-101UH accepts up to 120W
LRP-104CET
Long Reach PoE Extender
Ext.
P1 P2 Fault
PWR
PoE
Power
Usage
10W 20W 30W 40W
OFF
Port PoE
12 3 4
ON
OFF
1
ON
OFF
2
ON
OFF
3
ON
OFF
4
PWR
LRP IN
LNK
Long Reach PoE
802.3af/802.3at PoE
1
2
Extender
3
4
ACTLNK
PoE In-use
LRP-104CET
PoE Power Budget
60 watts~120 watts (max.)
UTP with DC power
over UTP input
PoE
PoE
PoE
PoE
PoE IP Camera
external power input
Power Output UTP with DC power over UTP output
RJ45 with 802.3at/af
PoE output
Installation Instructions
Step 1. Remove the “Danger – No Ethernet” label stuck on the RJ45 LRP
ports of LRP-101UH.
Step 2. Connect the LRP Injector (LRP-101UH) and LRP Extender
(LRP-104CET) to ends of RJ45 terminated long UTP/twisted-pair
cable.
1. Please do not connect any Ethernet equipment to LRP
OUT Port of the LRP-101UH; otherwise, it will damage the
Ethernet equipment.
Warning
2. Please do not connect any Ethernet equipment to LRP IN Port
of the LRP-104CET; otherwise, it will damage the Ethernet
equipment.
Step 3. Connect Cat5/6 UTP cable to LRP-101UH and non-PoE switch or
workstation.
Step 4. Connect 48~56V DC power adapter to LRP-101UH power socket, and
then the PWR LED of LRP-101UH and LRP-104CET should be lit up
immediately.
Step 5. Connect Cat5/6 UTP cable to LRP-104CET and IEEE 802.3at/af
complied PoE IP camera or PoE Wireless AP.
23
Page 24
1. PoE output capacity is based on different DC Power Input /
PoE Input.
2. The LRP-101UH has two power input options; only one mode
Note
is available at one time. PoE power input cannot be used if
power input of DC 52V or 56V is selected.
6.3 Applications of LRP Injector or LRP Switch powered by
External DC power supply
The LRP-104CET can be powered via External DC 24~48V input. You can
refer to Section 5.3 for Installation Precautions of Local Power. This
section describes its applications and precautions.
When the External DC power in is used, the LRP-104CET can
provide each port up to 25 watts of PoE output. The PoE power
Note
Type 1 One LRP-101CH and one LRP-104CET with PoE power output
budget can be increased to 120 watts.
Local Power
802.3af / 802.3at
PoE Switch
Local Power
110-240V AC
Ethernet Switch
24
Cat5e/6
AC-to-DC Adapter
60W/48~56V DC IN
Cat5e/6
PoE
PoE
Long Reach Power over Ethernet
LRP-101CH
Long Reach PoE Injector
Long Reach Power over Ethernet
LRP-101CH
Long Reach PoE Injector
LRP-104CET
Long Reach PoE Extender
Ext.
P1 P2 Fault
PWR
PoE
Power
Usage
10W 20W 30W 40W
OFF
Port PoE
12 3 4
ON
OFF
1
ON
OFF
2
ON
OFF
3
ON
OFF
4
PWR
LRP IN
LNK
Long Reach PoE
1
2
Extender
3
4
ACTLNK
PoE In-use
LRP-104CET
PoE Power Budget
LRP-104CET
Long Reach PoE Extender
Ext.
PWR
P1 P2 Fault
PoE
Power
Usage
10W 20W 30W 40W
OFF
Port PoE
12 3 4
ON
OFF
1
ON
OFF
2
ON
OFF
3
ON
OFF
4
PWR
LRP IN
LNK
Long Reach PoE
1
2
Extender
3
4
ACTLNK
PoE In-use
LRP-104CET
PoE Power Budget
DC
802.3af/802.3at PoE
PoE
PoE
PoE
PoE
120 watts (max.)
DC
802.3af/802.3at PoE
PoE
PoE
PoE
PoE
120 watts (max.)
120W/24-48V DC
Power Supply
PoE IP Camera
120W/24-48V DC
Power Supply
PoE IP Camera
Page 25
Functions
Power Input
Power Output
RJ45 with 802.3at/af PoE input
Power adapter with 48~56V DC in
BNC with DC power over coaxial
output
LRP Injector LRP Extender
LRP-101CH LRP-104CET
External DC 24~48V
power input
RJ45 with 802.3at/af
PoE output
After the power over coaxial injector is enabled, the center
pin of the coaxial cable has electricity. Please do not touch the
Warning
center pin.
Type 2 One LRP-822CS/LRP-1622CS and one LRP-104CET with PoE power
output
Local Power
LRP-822CS
110-240V AC
Power over Coaxial
Coaxial
Up to 400m
Coaxial
Up to 400m
LRP-104CET
Long Reach PoE Extender
Ext.
PWR
P1 P2 Fault
PoE
Power
Usage
10W 20W 30W 40W
OFF
Port PoE
1 2 3 4
ON
OFF
1
ON
OFF
2
ON
OFF
3
ON
OFF
4
PWR
LRP IN
LNK
Long Reach PoE
1
2
Extender
3
4
ACTLNK
PoE In-use
LRP-104CET
Ext.
PWR
P1 P2 Fault
PoE
Power
Usage
10W 20W 30W 40W
OFF
Port PoE
1 2 3 4
ON
OFF
1
ON
OFF
2
ON
OFF
3
ON
OFF
4
PWR
LRP IN
LNK
Long Reach PoE
1
2
Extender
3
4
ACTLNK
PoE In-use
LRP-104CET
802.3at PoE+
DC
UTP
PoE
PoE
PoE
PoE
DC
UTP
PoE
PoE
PoE
PoE
PoE
IP Camera
120W/24-48V DC
Power Supply
PoE Power Budget
120 watts (max.)
120W/24-48V DC
Power Supply
PoE Power Budget
120 watts (max.)
Functions
Power Input
Power Output
LRP Switch LRP Extender
LRP-822CS/LRP-1622CS LRP-104CET
Power cord with AC 100~240V,
50/60Hz, auto-sensing
BNC with DC power over coaxial
output
External DC 24~48V
power input
RJ45 with 802.3at/af PoE
output
25
Page 26
After the power over coaxial injector is enabled, the center
pin of the coaxial cable has electricity. Please do not touch the
Warning
center pin.
Type 3 LRP-101UH and LRP-104CET with PoE power output
Local Power
PoE
Long Reach Power over Ethernet
PoE
802.3af / 802.3at
PoE Switch
Cat5e/6
LRP-101UH
Long Reach PoE Injector
Local Power
110-240V AC
AC-to-DC Adapter
60W/48~56V DC IN
Long Reach Power over Ethernet
LRP-101UH
Long Reach PoE Injector
LRP Injector LRP Extender
LRP-101UH LRP-104CET
Ethernet Switch
Functions
Power Input
Cat5e/6
RJ45 with 802.3at/af PoE input
Power adapter with 48~56V DC in
Power Output UTP with DC power over UTP output
LRP-104CET
Long Reach PoE Extender
Ext.
PWR
P1 P2 Fault
PoE
Power
Usage
10W 20W 30W 40W
OFF
Port PoE
12 3 4
ON
OFF
1
ON
OFF
2
ON
OFF
3
ON
OFF
4
PWR
LRP IN
LNK
Long Reach PoE
1
2
Extender
3
4
ACTLNK
PoE In-use
LRP-104CET
PoE Power Budget
LRP-104CET
Long Reach PoE Extender
Ext.
P1 P2 Fault
PWR
PoE
Power
Usage
10W 20W 30W 40W
OFF
Port PoE
12 3 4
ON
OFF
1
ON
OFF
2
ON
OFF
3
ON
OFF
4
PWR
LRP IN
LNK
Long Reach PoE
1
2
Extender
3
4
ACTLNK
PoE In-use
LRP-104CET
PoE Power Budget
DC
802.3af/802.3at PoE
PoE
PoE
PoE
PoE
120 watts (max.)
DC
802.3af/802.3at PoE
PoE
PoE
PoE
PoE
120 watts (max.)
External DC 24~48V
power input
RJ45 with 802.3at/af
PoE output
120W/24-48V DC
Power Supply
PoE IP Camera
120W/24-48V DC
Power Supply
PoE IP Camera
Warning
26
1. Please do not connect any Ethernet equipment to LRP
OUT Port of the LRP-101UH; otherwise, it will damage the
Ethernet equipment.
2. Please do not connect any Ethernet equipment to LRP IN Port
of the LRP-104CET; otherwise, it will damage the Ethernet
equipment.
Page 27
Appendix A: Networking Connection
A.1 Switch’s RJ45 Pin Assignments
10/100Mbps, 10/100BASE-TX
RJ45 Connector pin assignment
MDI
Contact
1 Tx + (transmit) Rx + (receive) Positive (VCC+)
2 Tx - (transmit) Rx - (receive) Positive (VCC+)
3 Rx + (receive) Tx + (transmit) Negative (VCC-)
4, 5 Not used Not used
6 Rx - (receive) Tx - (transmit) Negative (VCC-)
7, 8 Not used Not used
Media Dependent
Interface
A.2 RJ45 Cable Pin Assignments
MDI-X
Media Dependent
Interface-Cross
PoE
The standard RJ45 receptacle/connector
27
Page 28
There are 8 wires on a standard UTP/STP cable and each wire is color-coded.
The following shows the pin allocation and color of straight cable and crossover
cable connection:
Straight Cable
12345678
12345678
Cross Over Cable
12345678
12345678
SIDE 1
SIDE 2
SIDE 1
SIDE 2
SIDE 1
1 = White/Orange
2 = Orange
3 = White/Green
4 = Blue
5 = White/Blue
6 = Green
7 = White/Brown
8 = Brown
SIDE 1 SIDE 2
1 = White/Orange
2 = Orange
3 = White/Green
4 = Blue
5 = White/Blue
6 = Green
7 = White/Brown
8 = Brown
SIDE 2
1 = White/Orange
2 = Orange
3 = White/Green
4 = Blue
5 = White/Blue
6 = Green
7 = White/Brown
8 = Brown
1 = White/Green
2 = Green
3 = White/Orange
4 = Blue
5 = White/Blue
6 = Orange
7 = White/Brown
8 = Brown
Figure A-1: Straight-through and Crossover Cable
Please make sure your connected cables are with the same pin assignment
and color as the above picture before deploying the cables into your network.
28
Loading...