Long Reach
PoE over Coaxial / UTP
Extender Kit
LRP-101C-KIT and LRP-101U-KIT
User’s Manual
Trademarks
Copyright © PLANET Technology Corp. 2015.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other
trademarks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work
properly in all environments and applications, and makes no warranty
and representation, either implied or expressed, with respect to
the quality, performance, merchantability, or tness for a particular
purpose.
PLANET has made every effort to ensure that this User’s Manual is
accurate; PLANET disclaims liability for any inaccuracies or omissions
that may have occurred.
Information in this User’s Manual is subject to change without notice
and does not represent a commitment on the part of PLANET. PLANET
assumes no responsibility for any inaccuracies that may be contained in
this User’s Manual. PLANET makes no commitment to update or keep
current the information in this User’s Manual, and reserves the right
to make improvements to this User’s Manual and/or to the products
described in this User’s Manual, at any time without notice.
If you nd information in this manual that is incorrect, misleading, or
incomplete, we would appreciate your comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the Instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may
cause radio interference, in which case the user may be required to
take adequate measures.
WEEE Warning
To avoid the potential effects on the environment and human
health as a result of the presence of hazardous substances
in electrical and electronic equipment, end users of electrical
and electronic equipment should understand the meaning of
the crossed-out wheeled bin symbol. Do not dispose of WEEE as
unsorted municipal waste and have to collect such WEEE separately.
Revision
PLANET Long Reach PoE over Coaxial / UTP Extender Kit User’s Manual
MODELS: LRP-101C-KIT / LRP-101U-KIT
REVISION: 1.0 (January 2015)
Part No: EM-LRP-101x-KIT_v1.0 (2350-AN0100-000)
TABLE OF CONTENTS
1. INTRODUCTION ........................................................................ 6
1.1 Package Contents ............................................................... 6
1.2 Introduction of Long Reach Power over Ethernet ................... 8
1.3 Product Features ................................................................. 9
1.4 Product Specications ........................................................10
1.4.1 LRP-101C-KIT Specications ......................................10
1.4.2 LRP-101U-KIT Specications ......................................13
2. HARDWARE DESCRIPTION ........................................................16
2.1 LRP-101CH ........................................................................16
2.1.1 LRP-101CH Physical Dimensions .................................16
2.1.2 LRP-101CH Front Panel and Rear Panel ......................17
2.1.3 LRP-101CH LED Indicators.........................................17
2.2 LRP-101CE ........................................................................18
2.2.1 LRP-101CE Physical Dimensions .................................18
2.2.2 LRP-101CE Front Panel and Rear Panel .......................19
2.2.3 LRP-101CE LED Indicators .........................................19
2.3 LRP-101UH........................................................................20
2.3.1 LRP-101UH Physical Dimensions ................................20
2.3.2 LRP-101UH Front Panel and Rear Panel ......................21
2.3.3 LRP-101UH LED Indicators ........................................21
2.4 LRP-101UE ........................................................................22
2.4.1 LRP-101UE Physical Dimensions .................................22
2.4.2 LRP-101UE Front Panel and Rear Panel .......................23
2.4.3 LRP-101UE LED Indicators .........................................23
3. INSTALLATION .........................................................................24
3.1 Installation Precautions of LRP-101C-KIT..............................24
3.2 Installation Precautions of LRP-101U-KIT .............................24
3.3 Power options: ..................................................................25
3.4 Applications of LRP-101C-KIT with coaxial cable ...................25
3.5 Applications of LRP-101U-KIT with UTP/Twisted-pair Cable ....28
3.6. Optional - DIN-Rail Mounting ..............................................31
4. TROUBLESHOOTING .................................................................33
APPENDIX A: NETWORKING CONNECTION .......................................34
A.1 Switch’s RJ45 Pin Assignments ............................................34
A.2 RJ45 Cable Pin Assignments ................................................34
1. INTRODUCTION
Thank you for purchasing PLANET Long Reach PoE over Coaxial / UTP
Extender Kit, the LRP-101C-KIT and LRP-101U-KIT. The descriptions of
the four models are as follows:
LRP-101C-KIT
LRP-101CH
LRP-101CE
LRP-101UH
LRP-101UE
“Long Reach PoE over Coaxial / UTP Extender Kit” mentioned in
this Manual represents the above four models.
1.1 Package Contents
Open the box of the Long Reach PoE over Coaxial / UTP Extender Kit
and carefully unpack it. The box should contain the following items:
1-Port 10/100TX PoE PD + 1-Port Coax Long Reach PoE
Injector
1-Port 10/100TX PoE PSE + 1-Port Coax Long Reach
PoE Extender
LRP-101U-KIT
1-Port 10/100TX PoE PD + 1-Port UTP Long Reach PoE
Injector
1-Port 10/100TX PoE PSE + 1-Port UTP Long Reach PoE
Extender
For LRP-101C-KIT
1-Port 10/100TX PoE
PD + 1-Port Coax Long
Reach PoE Injector –
LRP-101CH x 1
6
1-Port 10/100TX PoE PSE + 1-Port Coax
Long Reach PoE Extender – LRP-101CE x
1
User’s Manual x 1 Warning Sticker x 1
For LRP-101U-KIT
1-Port 10/100TX PoE PD + 1-Port
UTP Long Reach PoE Injector –
LRP-101UH x 1
User’s Manual x 1 Warning Sticker x 2
Warning Sticker x 1
1-Port 10/100TX PoE PSE +
1-Port UTP Long Reach PoE
Extender – LRP-101UE x 1
7
If any of these are missing or damaged, please contact
Up to 1000m
your dealer immediately; if possible, retain the carton
including the original packing material, and use them
Note
again to repack the product in case there is a need to
return it to us for repair.
1.2 Introduction of Long Reach Power over Ethernet
PLANET LRP-101C-KIT and LRP-101U-KIT series PoE over Coaxial
Extender and PoE over UTP Extender are designed to extend IP
Ethernet transmission and inject power over an existing coaxial, UTP
or twisted-pair cable or for distance up to 1000m (3280ft) to PoE IP
camera, PoE wireless AP and any 802.3af/at complied powered device
(PD). It is a perfect solution for sending IP video links and power to
remotely-installed PoE IP cameras that are beyond the 100 meters
distance limit of Ethernet.
Power over Coaxial, UTP or Twisted-pair cable
The Long Reach PoE solution allows Ethernet Data and PoE or PoE+ to
be transmitted using coaxial, UTP or twisted-pair cable. Based on IEEE
802.3at Power over Ethernet Plus and up to 25 watts of power output,
PLANET Long Reach PoE extender solution eliminates the need for
additional remote site power while allowing a single PoE source, such
as a PoE network switch, to provide power to both LRP Extenders and
the camera at long range. This feature eliminates the need for local
and remote site power supplies.
PoE IP Cam
PoE
LRP-101CE
Extender
LRP-101CH
Control Center
Injector
Data
Coaxial Cable
Power
8
Stable Operating Performance under Difcult Environments
PLANET Long Reach PoE Extender is the perfect solution for extended
distance data and power transmission for warehouses, parking lots,
campuses, casinos, and many more. They can operate stably under
temperature range from -20 to 70 degrees C which enables the users
to conveniently apply the device in almost any location of the network.
1.3 Product Features
Power over Ethernet
z Eliminates Power cabling with PoE over Coaxial
z Supports Power over Ethernet PSE, PoE Injector
z Power and Ethernet data transmission over coaxial up to 1km
z Power and Ethernet data transmission over UTP up to 500m
z Complies with IEEE 802.3af / IEEE 802.3at Power over Ethernet PD
on RJ45 port
z Supports Long Reach PoE power up to 30.8 watts (Vary on power
source and cable distance)
z Supports PoE Power up to 25 watts (Vary on power source and cable
distance)
z Auto detect remote powered device (PD)
z Plug and Play, no PC required
Industrial Case / Installation
z Supports extensive LED indicators for network diagnostics
z Metal case protection
z Compact size, DIN-rail and wall-mount design
z Supports 2000V DC EFT surge protection for power line
z Supports 2000V DC Ethernet ESD protection
z -20 to 70 degrees C operating temperature
9
1.4 Product Specications
1.4.1 LRP-101C-KIT Specications
Model LRP-101CH LRP-101CE
Functions Long Reach PoE Injector
Hardware Specications
10/100BASE-TX RJ45
Auto-negotiation/ Auto-MDI/MDI-X
IEEE 802.3at/af PoE PD
(Powered Device)
Supports both Mid-Span
and End-Span PSE
Input Range: 48~56V
DC
100 meters
1522bytes
Ethernet
Interface
Copper
Power over
Ethernet
Standard
PoE Input
PoE Output ─
PoE Budget ─ Up to 25 watts
PoE Mode ─
Data Rate 100/100Mbps
Cabling Cat5e or above
Maximum
Distance
Maximum Frame
sizes
Long Reach PoE
Extender
IEEE 802.3at/af PoE
PSE (Power Source
Equipment)
─
48~56V DC, 600mA
max.
End-span, RJ45 Pin
1/2(+), 3/6(-)
Long
Reach
PoE
Interface
10
Connectivity
1 x BNC female
connector
Long Reach PoE over
coaxial PSE
(Power Source
Equipment)
1 x BNC female
Long Reach PoE over
coaxial PD
(Powered Device)
Long
Reach
PoE
Interface
Power Input ─ 37~56V DC
Power Output 41~56V DC ─
Power Pin
Assignment
Cabling
Maximum
Distance
Long Reach
Ethernet
Standard
Modulation Type Wavelet-OFDM
Security 128-bit AES encryption
Frequency Band 2 ~ 28 MHz
Encryption AES 128-bit
Performance**
BNC center pole :
DC+
BNC shield : DC -
Coaxial cable: 75 ohm
RG-6/U cable, less than 12Ω/1000 ft
RG-59/U cable, less than 30Ω/1000 ft.
Max. 200m with PoE+ output (656ft.)
Max. 600m with PoE output (1968ft.)
Max. 1200m without PoE output (3,937ft.)
IEEE 1901
Data Rate*
Distance
200m 93 / 93 Mbps 29W 16W
400m 93 / 93 Mbps 22W 14W
600m 87 / 91 Mbps 13W 10W
800m 75 / 83 Mbps 10W 8W
1000m 55 / 73 Mbps 8W 7W
(Upload /
Download)
BNC center pole :
DC+
BNC shield : DC -
LRP-101CE 802.3af/at
PoE Output Capability**
LRP-101CH
W/56V DC
IN
LRP-101CH
W/30W
PoE+ IN
11
LRP-101CE - 1-Port LRP
Extender
Long
Reach
PoE
Interface
LED Indicators
ESD Protection 2KV DC
EFT Protection 2KV ─
Enclosure Metal case
Installation Wall mount or DIN rail with optional kit
Dimensions (W x D x H) 94 x 70 x 26 mm
Weight 200g 375g
Power Requirements
Standards Conformance
Standards Compliance
Regulation Compliance FCC Part 15 Class A, CE
Environment
Temperature
LRP Compatibility
4 x LEDs
PWR
LRP LNK
PoE IN
LNK/ACT
RJ45 PoE Input:
802.3at/af 48~56V
DC
DC Input: 48~56V DC
IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast Ethernet
IEEE 802.3af Power over Ethernet (802.3at Type 1)
IEEE 802.3at Power over Ethernet (802.3at Type 2)
Operating: -20~70 degrees C
Storage: -40~75 degrees C
With power over coaxial
input
LRP-101CH – 1-Port
LRP Injector
LRP-822CS – 8-Port
LRP over Coax Switch
LRP-1622CS – 16-Port
LRP over Coax Switch
4 x LEDs
PWR
LRP LNK
PoE-in-use
LNK/ACT
BNC Power over Coaxial
Input: 44~56V DC
12
Humidity
Operating: 5~95% (Non-condensing)
Storage: 5~95% (Non-condensing)
* 1. Upload: LRP-101CE to LRP-101CH. Download: LRP-101CH to LRP-
101CE.
2. As there are various resistance values in the category of RG-59/U
or RG-6/U cable, the actual data rate will vary on the quality of
the copper wire and environment factors.
** Depending on what the DC/PoE Power Input and the length of
coaxial cable are.
1.4.2 LRP-101U-KIT Specications
Model LRP-101UH LRP-101UE
Hardware Specications
10/100BASE-TX RJ45
Auto-negotiation/ Auto-MDI/MDI-X
IEEE 802.3at/af PoE PD
(Powered Device)
Supports both Mid-Span
and End-Span PSE
Input Range: 48~56V
DC
100m
1522bytes
IEEE 802.3at/af PoE
PSE (Power Source
Equipment)
48~56V DC, 600mA
max.
End-span, RJ45 Pin
1/2(+), 3/6(-)
Ethernet
Interface
Copper
Power over
Ethernet
Standard
PoE Input
PoE Output ─
PoE Budget ─ Up to 25 watts
PoE Mode ─
Data Rate 100/100Mbps
Cabling Cat5e or above
Maximum
Distance
Maximum Frame
sizes
13
Long
Reach
PoE
Interface
1 x RJ45 connector
Long Reach PoE over
Connectivity
Power Input ─ 37~56V DC
Power Output 41~56V DC
Power Pin
assignment
Cabling UTP cable:
Maximum
distance
Long Reach
Ethernet
Standard
Modulation Type Wavelet-OFDM
Security 128-bit AES encryption
Frequency Band 2 ~ 28 MHz
Encryption AES 128-bit
Performance**
UTP PSE
(Power Source
Equipment)
RJ45 PIN 1,3,5,7: VCC+ RJ45 PIN 1,3,5,7: VCC+
RJ45 PIN 2,4,6,8: VCC- RJ45 PIN 2,4,6,8: VCC-
Max. 100m with PoE+ output (328 ft.)
Max. 400m with PoE output (1,312 ft.)
Max. 500m without PoE output (1,640 ft.)
IEEE 1901
Data Rate*
Distance
100m 94 / 94 Mbps 30W 19W
200m 82 / 82 Mbps 30W 18W
300m 63 / 67 Mbps 30W 17W
400m 44 / 48 Mbps 22W 14W
500m 30 / 30 Mbps 18W 12W
(Upload /
Download)
1 x RJ45 connector
Long Reach PoE over
UTP PD (Powered
Device)
LRP-101UE 802.3af/at
PoE Output Capability**
LRP-101UH
W/56V DC
IN
LRP-101UH
W/30W
PoE+ IN
14
4 x LEDs
PWR
LED Indicators
ESD Protection 2KV DC
EFT Protection 2KV ─
Enclosure Metal case
Installation Wall mount or DIN rail with optional kit
Dimensions (W x D x H) 94 x 70 x 26 mm
Weight 193g 190g
Power Requirements
Standards Conformance
Standards Compliance
Regulation Compliance FCC Part 15 Class A, CE
Environment
Temperature
Humidity
LRP LNK
PoE IN
LNK/ACT
RJ45 PoE Input:
802.3at/af 48~56V
DC
DC Input: 48~56V DC
IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast Ethernet
IEEE 802.3af Power over Ethernet (802.3at Type 1)
IEEE 802.3at Power over Ethernet (802.3at Type 2)
Operating: -20~70 degrees C
Storage: -40~75 degrees C
Operating: 5~95% (non-condensing)
Storage: 5~95% (non-condensing)
4 x LEDs
PWR
LRP LNK
PoE-in-use
LNK/ACT
Power over RJ45 Input:
44~56V DC
* 1. Upload: LRP-101UE to LRP-101UH. Download: LRP-101UH to LRP-
101UE.
2. As there are various resistance values in the category 5/5e cable,
the actual data rate will vary on the quality of the copper wire and
environment factors.
** Depending on what the DC/PoE Power Input and the length of UTP
cable are.
15
2. HARDWARE DESCRIPTION
Rear Panel
Front Panel
2.1 LRP-101CH
2.1.1 LRP-101CH Physical Dimensions
z LRP-101CH dimensions (W x D x H): 94 x 70.3 x 26.2 mm
48~56V DC IN
LRP-101CH
Long Reach PoE Injector - Coax
Top Panel
LRP OUT
LNK/ACTPoE IN
10/100BASE-TX
Long Reach Power over Ethernet
Injector
LNK
CAUTION
The LRP interface is
PWR
allowed to connect to
LRP Extender only.
Bottom
16
2.1.2 LRP-101CH Front Panel and Rear Panel
Figure 2-1 and Figure 2-2 show the front and rear panels of the
LRP-101CH Long Reach PoE over Coaxial Injector.
LRP-101CH
Long Reach PoE Injector - Coax
LRP OUT
LNK
PWR
Injector
CAUTION
The LRP interface is
allowed to connect to
LRP Extender only.
48~56V DC IN
LNK/ACTPoE IN
10/100BASE-TX
Figure 2-1: LRP-101CH Front Panel Figure 2-2: LRP-101CH Rear Panel
2.1.3 LRP-101CH LED Indicators
System
LED Color Function
Power ON: PoE+ / PoE power input from RJ45
PoE PD port
Lit
PWR Green
LRP Coaxial Interface
LED Color Function
LNK Green
RJ45 10/100BASE-TX Interface
LED Color Function
PoE IN Amber
LNK/
ACT
Green
Power ON: 48~56V DC power input from DC
jack
Off Power Off
Lit: indicates that the coaxial link is established.
Off: indicates that the coaxial link is down.
Lit: indicates the RJ45 port is receiving the PoE
Power.
Blink: indicates the extender is actively sending or
receiving data over that port.
17
2.2 LRP-101CE
Rear Panel
Front Panel
2.2.1 LRP-101CE Physical Dimensions
z LRP-101CE dimensions (W x D x H): 94 x 70.3 x 26.2 mm
LNK/ACTPoE In-use
PoE OUT
10/100BASE-TX
Top Panel
Bottom
Long Reach Power over Ethernet
LRP-101CE
Long Reach PoE Extender - Coax
18
LRP IN
Extender
LNK
PWR
2.2.2 LRP-101CE Front Panel and Rear Panel
Figure 2-3 and Figure 2-4 show the front and rear panels of the
LRP-101CE Long Reach PoE over Coaxial Extender.
LRP-101CE
Long Reach PoE Extender - Coax
LRP IN
PWR
Extender
LNK
PoE OUT
LNK/ACTPoE In-use
10/100BASE-TX
Figure 2-3: LRP-101CE Front Panel Figure 2-4: LRP-101CE Rear Panel
2.2.3 LRP-101CE LED Indicators
System
LED Color Function
PWR Green Lit: indicates the power is on.
LRP Coaxial Interface
LED Color Function
LNK Green
RJ45 10/100BASE-TX Interface
LED Color Function
PoE-in-Use Amber
LNK/ACT Green
Lit: indicates that the coaxial link is established.
Off: indicates that the coaxial link is down.
Lit: indicates the RJ45 Port is providing PoE
power.
Blink: indicates the extender is actively
sending or receiving data over that port.
19
2.3 LRP-101UH
Rear Panel
Front Panel
2.3.1 LRP-101UH Physical Dimensions
z LRP-101UH dimensions (W x D x H): 94 x 70.3 x 26.2 mm
48~56V DC IN
LRP-101UH
Injector
Long Reach PoE Injector - UTP
Top Panel
CAUTION
The LRP interface is
allowed to connect to
LRP Extender only.
LNK/ACTPoE IN
10/100BASE-TX
Long Reach Power over Ethernet
LRP OUT
LNK
PWR
Bottom
20
2.3.2 LRP-101UH Front Panel and Rear Panel
Figure 2-5 and Figure 2-6 show the front and rear panels of the
LRP-101UH Long Reach PoE over UTP Injector.
LRP-101UH
CAUTION
The LRP interface is
allowed to connect to
LRP Extender only.
Injector
Long Reach PoE Injector - UTP
PWR
LRP OUT
LNK
48~56V DC IN
LNK/ACTPoE IN
10/100BASE-TX
Figure 2-5: LRP-101UH Front Panel Figure 2-6: LRP-101UH Rear Panel
2.3.3 LRP-101UH LED Indicators
System
LED Color Function
Power ON: PoE+ / PoE power input from RJ45
PoE PD port
Lit
PWR Green
LRP UTP Interface
LED Color Function
LNK Green
RJ45 10/100BASE-TX Interface
LED Color Function
PoE IN Amber
LNK/
ACT
Green
Power ON: 48~56V DC power input from DC
jack
Off Power Off
Lit: indicates that the UTP link is established.
Off: indicates that the UTP link is down.
Lit: indicates the RJ45 port is receiving the PoE
Power.
Blink: indicates the extender is actively sending or
receiving data over that port.
21
2.4 LRP-101UE
Rear Panel
Front Panel
2.4.1 LRP-101UE Physical Dimensions
z LRP-101UE dimensions (W x D x H): 94 x 70.3 x 26.2 mm
LNK/ACTPoE In-use
PoE OUT
10/100BASE-TX
Top Panel
Bottom
Long Reach Power over Ethernet
LRP-101UE
Extender
Long Reach PoE Extender - UTP
22
LRP IN
LNK
PWR
2.4.2 LRP-101UE Front Panel and Rear Panel
Figure 2-7 and Figure 2-8 show the front and rear panels of the
LRP-101UE Long Reach PoE over UTP Extender.
LRP-101UE
Extender
Long Reach PoE Extender - UTP
PWR
LRP IN
LNK
PoE OUT
LNK/ACTPoE In-use
10/100BASE-TX
Figure 2-7: LRP-101UE Front Panel Figure 2-8: LRP-101UE Rear Panel
2.4.3 LRP-101UE LED Indicators
System
LED Color Function
PWR Green Lit: indicates the power is on.
LRP UTP Interface
LED Color Function
LNK Green
RJ45 10/100BASE-TX Interface
LED Color Function
PoE-in-Use Amber
LNK/ACT Green
Lit: indicates that the LRP UTP link is established.
Off: indicates that the LRP UTP link is down.
Lit: indicates the RJ45 Port is providing PoE
power.
Blink: indicates the extender is actively
sending or receiving data over that port.
23
3. INSTALLATION
This section describes the functionalities of the Long Reach PoE over
Coaxial / UTP Extender Kit’s components and guides you to how to
install it on the desktop. Basic knowledge of networking is expected.
Please read this chapter completely before continuing.
3.1 Installation Precautions of LRP-101C-KIT
As the LRP-101CH is power over coaxial injector, it only can work with
PLANET power over coaxial extender, the LRP-101CE. Please conrm
that other non-PoE equipment is not connected with the coaxial cable.
When you connect the coaxial cable with coax-LAN converter, CCTV
camera, etc, it might cause other equipment to damage.
The package contains one Warning Sticker, which should
be stuck on the coaxial cable connector before using
PLANET Long Reach PoE over Coaxial Extender Kit.
Caution
the device.
careful before plugging into
Please be reminded that the cable con
contains electric power. Please be
Warning:
This side of connector
Do Not Touch
the Center Pin
3.2 Installation Precautions of LRP-101U-KIT
The package contains one Warning Sticker and it is stuck on the
PoE IN / LRP OUT RJ45 connector of PLANET Long Reach PoE over
UTP Extender Kit. As the LRP-101UH is power over UTP, it only can
work with PLANET LRP-101UE. If connected with standard Ethernet
equipment, it might cause damage to the equipment.
24
3.3 Power options:
Caution
LRP Injector
There are two ways to power the LRP Injector (LRP-101CH and
LRP-101UH):
z Powered via PoE
z Powered via DC adapter
LRP Extender
The LRP Extender must be powered by the LRP Injector or LRP
Switch
z LRP-101CE must be powered by the LRP-101CH or LRP CS-series
switch over coaxial cable
z LRP-101UE must be powered by the LRP-101UH or LRP US-series
switch over UTP/Twisted-pair cable
Please don’t connect the LRP Extender to any PoE PSE
(Power Sourcing Equipment).
3.4 Applications of LRP-101C-KIT with coaxial cable
Type 1 – One LRP-101CH with PoE power input and one LRP-101CE
with PoE power output
The LRP Injector is powered via IEEE 802.3at/af PoE. An IEEE
802.3at/af compliant PoE PD will automatically be powered by the LRP
Extender via UTP.
802.3af / 802.3at
PoE Switch
PoE
PoE
CAT5e/6
Long Reach Power over Ethernet
LRP-101CH
Long Reach PoE Injector
Power over Coaxial
LRP-101CE
Long Reach PoE Extender
Long Reach Power over Ethernet
802.3af/802.3at
PoE
PoE
CAT5e/6
PoE IP Camera
25
Functions
Note
Power Input
Power
Output
LRP Injector LRP Extender
LRP-101CH LRP-101CE
RJ45 with 802.3at/af
PoE input
BNC with DC power over
coaxial output
Installation Instructions
Connect the LRP Injector (LRP-101CH) and LRP
Step 1
Step 2
Extender (LRP-101CE) to ends of BNC terminated
coaxial cable.
Stick the “Warning Sticker” on the coaxial cable.
Connect Cat5/6 UTP cable to LRP-101CH and IEEE
802.3at compliant PoE Switch or PoE Injector. If the PoE
switch or PoE injector is powered on already, then the
PWR LED of LRP-101CH and LRP-101CE should lit up
immediately.
BNC with DC power over
coaxial input
RJ45 with 802.3at/af
PoE output
Step 3
Warning
26
Connect Cat5/6 UTP cable to LRP-101CE and IEEE
802.3at/af complied PoE IP camera or PoE Wireless AP.
The LRP-101CH accepts IEEE 802.3at equipment for
optimal power injection. The other non-standard PoE
power devices may cause the LRP-101CH to malfunction.
1. Before installation, please consider the distance
and watts value demand for PD devices. The LRP101C-KIT PoE powers output capacity and upload /
download performance depending on the length of
coaxial cable.
2. As there are various resistance values in the category
of RG-59/U or RG-6/U cable, the actual data rate will
vary on the quality of the copper wire and environmental factors.
Type 2 – One LRP-101CH with 48~56V power adapter and one
110-240V AC
LRP-101CE with PoE power output
The LRP Injector is powered via the external power adapter. The
IEEE 802.3at/af compliant PoE PD will automatically be powered by the
LRP Extender via UTP.
AC-to-DC Adapter
60W/48~56V DC IN
Ethernet Switch
CAT5e/6
Functions
Power Input
Power
Output
Long Reach Power over Ethernet
LRP-101CH
Long Reach PoE Injector
LRP Injector LRP Extender
LRP-101CH LRP-101CE
Power adapter with
48~56V DC in
BNC with DC power over
coaxial output
Installation Instructions
Connect the LRP Injector (LRP-101CH) and LRP
Step 1
Step 2
Step 3
Extender (LRP-101CE) to ends of BNC terminated
coaxial cable.
Stick the “Warning Sticker” on the coaxial cable.
Connect Cat5/6 UTP cable to LRP-101CH and non-PoE
switch or workstation.
Connect 48~56V DC power adapter to LRP-101CH power
socket, then the PWR LED of LRP-101CH and LRP-101CE
should lit up immediately.
Power over Coaxial
LRP-101CE
Long Reach PoE Extender
Long Reach Power over Ethernet
802.3af/802.3at
PoE
PoE
CAT5e/6
PoE IP Camera
BNC with DC power over
coaxial input
RJ45 with 802.3at/af
PoE output
Step 4
Connect Cat5/6 UTP cable to LRP-101CE and IEEE
802.3at/af complied PoE IP camera or PoE Wireless AP.
27
Note
1. Before installation, please consider the distance
and watts value demand for PD devices. The LRP101C-KIT PoE powers output capacity and upload /
download performance depending on the length of
coaxial cable.
2. As there are various resistance values in the category
of RG-59/U or RG-6/U cable, the actual data rate will
vary on the quality of the copper wire and environment al factors.
3. PoE output capacity is based on different DC Power
Input / PoE Input.
4. The LRP-101CH has two power input options; only
one mode is available at one time. PoE power input
cannot be used if power input of DC 52V or 56V is
selected.
3.5 Applications of LRP-101U-KIT with UTP/Twisted-pair
Cable
Type 1 – LRP-101UH with PoE power input and LRP-101UE with PoE
power output
802.3af / 802.3at
PoE Switch
Functions
Power Input
Power
Output
28
PoE
PoE
CAT5e/6
Long Reach Power over Ethernet
LRP-101UH
Long Reach PoE Injector
LRP Injector LRP Extender
LRP-101UH LRP-101UE
RJ45 with 802.3at/af
PoE input
UTP with DC power over
UTP output
Power over UTP
LRP-101UE
Long Reach PoE Extender
Long Reach Power over Ethernet
802.3af/802.3at
PoE
PoE
CAT5e/6
PoE IP Camera
UTP with DC power over
UTP input
RJ45 with 802.3at/af
PoE output
Installation Instructions
Note
Step 1
Step 2
Warning
Step 3
Step 4
Warning
Remove the “Danger – No Ethernet” labels stuck on
the RJ45 LRP port of LRP-101UH and LRP-101UE.
Connect the LRP Injector (LRP-101UH) and LRP
Extender (LRP-101UE) to ends of RJ45 terminated long
UTP/twisted-pair cable.
1. Please do not connect any Ethernet equipment to LRP
OUT Port of the LRP-101UH; otherwise, it will damage
the Ethernet equipment.
2. Please do not connect any Ethernet equipment to LRP
IN Port of the LRP-101UE; otherwise, it will damage
the Ethernet equipment.
Connect Cat5/6 UTP cable to LRP-101UH and IEEE
802.3at compliant PoE Switch or PoE Injector. If the PoE
switch or PoE injector is powered on already, then the
PWR LED of LRP-101UH and LRP-101UE should lit up
accordingly.
Connect Cat5/6 UTP cable to LRP-101UE and IEEE
802.3at/af complied PoE IP camera or PoE Wireless AP.
The LRP-101UH accepts IEEE 802.3at equipment for
optimal power injection. The other non-standard PoE
Power devices may cause the LRP-101UH to malfunction.
1. Before installation, please consider the distance
and watts value demand for PD devices. The LRP101U-KIT PoE powers output capacity and upload
/ download performance depending on the length of
UTP cable.
2. As there are various resistance values in the category 5/5e cable, the actual data rate will vary on the
quality of the copper wire and environmental factors.
29
Type 2 – LRP-101UH with 48~56V power adapter and LRP-101UE with
110-240V AC
PoE power output
AC-to-DC Adapter
60W/48~56V DC IN
Ethernet Switch
CAT5e/6
Functions
Power Input
Power
Output
Long Reach Power over Ethernet
LRP-101UH
Long Reach PoE Injector
LRP Injector LRP Extender
LRP-101UH LRP-101UE
Power adapter with
48~56V DC in
UTP with DC power over
UTP output
Installation Instructions
Step 1
Step 2
Warning
Remove the “Danger – No Ethernet” labels stuck on
the RJ45 LRP ports of LRP-101UH and LRP-101UE.
Connect the LRP Injector (LRP-101UH) and LRP
Extender (LRP-101UE) to ends of RJ45 terminated long
UTP/twisted-pair cable.
1. Please do not connect any Ethernet equipment to LRP
OUT Port of the LRP-101UH; otherwise, it will damage
the Ethernet equipment.
2. Please do not connect any Ethernet equipment to LRP
IN Port of the LRP-101UE; otherwise, it will damage
the Ethernet equipment.
Power over UTP
LRP-101UE
Long Reach PoE Extender
Long Reach Power over Ethernet
802.3af/802.3at
PoE
PoE
CAT5e/6
PoE IP Camera
UTP with DC power over
UTP input
RJ45 with 802.3at/af PoE
output
30
Step 3
Note
Step 4
Connect Cat5/6 UTP cable to LRP-101UH and non-PoE
switch or workstation.
Connect 48~56V DC power adapter to LRP-101UH power
socket, and then the PWR LED of LRP-101UH and LRP101UE should lit up immediately.
Step 5
Connect Cat5/6 UTP cable to LRP-101UE and IEEE
802.3at/af complied PoE IP camera or PoE Wireless AP.
1. Before installation, please consider the distance
and watts value demand for PD devices. The LRP101U-KIT PoE powers output capacity and upload
/ download performance depending on the length of
UTP cable.
2. As there are various resistance values in the category 5/5e cable, the actual data rate will vary on the
quality of the copper wire and environmental factors.
3. PoE Output Capacity is based on different DC Power
Input / PoE Input.
4. The LRP-101UH has two power input options; only
one mode is available at one time. PoE power input
cannot be used if power input of DC 52V or 56V is
selected.
3.6. Optional - DIN-Rail Mounting
There are two DIN-Rail holes on the left side of the Long Reach PoE
over Coaxial / UTP Extender Kit that allow the device to be easily
installed with DIN-Rail mounting. The PLANET optional DIN-Rail
mounting Kit – RKE-DIN can be ordered separately. When you need
to replace the wall mount application with DIN-Rail application on
the Long Reach PoE over Coaxial / UTP Extender Kit, please refer to
following gures to screw the DIN-Rail on the Long Reach PoE over
Coaxial/UTP Extender Kit. To hang the Long Reach PoE over Coaxial /
UTP Extender Kit, follow the steps below:
31
Step 1: Screw the DIN-Rail on the Long Reach PoE over Coaxial /
Caution
UTP Extender Kit.
Step 2: Lightly slide the DIN-Rail into the track.
1
2
Step 3: Check whether the DIN-Rail is tightly on the track.
You must use the screws supplied with the mounting
brackets. Damage caused to the parts by using incorrect
screws would invalidate your warranty.
32
4. TROUBLESHOOTING
This chapter contains information to help you solve issues. If the Long
Reach PoE over Coaxial / UTP Extender Kit is not functioning properly,
make sure the Long Reach PoE over Coaxial / UTP Extender Kit is set
up according to instructions in this manual.
What is the maximum distance supported by LRP-101C-KIT
and LRP-101U-KIT?
Solution:
1. The LRP-101C-KIT supports a maximum distance of 1km.
2. The LRP-101U-KIT supports a maximum distance of 500m.
May I know which power source that can be accepted by LRP101C-KIT and LRP-101U-KIT?
Solution:
1. DC 56V power adapter.
2. DC 48V power adapter.
3. IEEE 802.3at High Power over Ethernet Switch.
4. IEEE 802.3af Power over Ethernet Switch.
The LRP-101C-KIT and LRP-101U-KIT Performance is bad.
Solution:
The actual data rate will vary on the quality of the coaxial / UTP cable
and environment factors.
33
APPENDIX A: NETWORKING CONNECTION
A.1 Switch’s RJ45 Pin Assignments
10/100Mbps, 10/100BASE-TX
RJ45 Connector pin assignment
MDI Media
Contact
1 Tx + (transmit) Rx + (receive) Positive (VCC+)
2 Tx - (transmit) Rx - (receive) Positive (VCC+)
3 Rx + (receive) Tx + (transmit) Negative (VCC-)
4, 5 Not used Not used
6 Rx - (receive) Tx - (transmit) Negative (VCC-)
7, 8 Not used Not used
Dependent
Interface
A.2 RJ45 Cable Pin Assignments
MDI-X Media
Dependent
Interface-Cross
PoE
The standard RJ45 receptacle/connector
34
There are 8 wires on a standard UTP/STP cable and each wire is colorcoded. The following shows the pin allocation and color of straight
cable and crossover cable connection:
Straight Cable
12345678
12345678
Crossover Cable
12345678
12345678
SIDE 1
SIDE 2
SIDE 1
SIDE 2
SIDE 1
1 = White/Orange
2 = Orange
3 = White/Green
4 = Blue
5 = White/Blue
6 = Green
7 = White/Brown
8 = Brown
SIDE 1 SIDE 2
1 = White/Orange
2 = Orange
3 = White/Green
4 = Blue
5 = White/Blue
6 = Green
7 = White/Brown
8 = Brown
SIDE 2
1 = White/Orange
2 = Orange
3 = White/Green
4 = Blue
5 = White/Blue
6 = Green
7 = White/Brown
8 = Brown
1 = White/Green
2 = Green
3 = White/Orange
4 = Blue
5 = White/Blue
6 = Orange
7 = White/Brown
8 = Brown
Figure A-1: Straight-through and Crossover Cable
Please make sure your connected cables are with the same pin
assignment and color as the above picture before deploying the cables
into your network.
35
EC Declaration of Conformity
For the following equipment:
*Type of Product: 1-Port 10/100TX PoE PD + 1-Port Coax Long Reach PoE Injector
*Model Number: LRP-101CH, LRP-101CE
* Produced by:
Manufacturer’s Name : Planet Technology Corp.
Manufacturer’s Address: 10F., No.96, Minquan Rd., Xindian Dist.
We hereby confirmed that the products mentioned comply with the requirements set out in
the Council Directive on the Approximation of the Laws of the Member States relating to
Electromagnetic Compatibility (2004/108/EC).
For the evaluation regarding the EMC, the following standards were applied:
Responsible for marking this declaration if the:
Manufacturer Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name: Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan
Person responsible for making this declaration
Name, Surname Kent Kang
Position / Title : Product Manager
1-Port 10/100TX PoE PSE + 1-Port Coax Long Reach PoE Extender
1-Port 10/100TX PoE PD + 1-Port UTP Long Reach PoE Injector
1-Port 10/100TX PoE PSE + 1-Port UTP Long Reach PoE Extender
LRP-101UH, LRP-101UE
New Taipei City 231, Taiwan (R.O.C.).
EN55022 (2010)
EN 61000-3-2 (2006 + A1:2009 + A2:2009)
EN 61000-3-3 (2008)
EN55024 (2010)
IEC 61000-4-2 (2008)
IEC 61000-4-3 (2006 + A1: 2007 + A2: 2010)
IEC 61000-4-4 (2012)
IEC 61000-4-5 (2005)
IEC 61000-4-6 (2008)
IEC 61000-4-11 (2004)
IEC 61000-4-8 (2009)
(R.O.C.)
Taiwan 31st March, 2015
Place Date Legal Signature
PLANET TECHNOLOGY CORPORATION
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:886-2-2219-9518 Fax:886-2-2219-9528
e-mail: sales@planet.com.tw http://www.planet.com.tw
Loading...