Planet FSD-1008HP User Manual

8-Port 10/100TX 802.3at PoE +

2-Port 10/100TX Desktop Switch

FSD-1008HP

User’s Manual

Copyright

Copyright © 2017 by PLANET Technology Corp. All rights reserved. No part of
this publication may be re-produced, transmitted, transcribed, stored in a retrieval
system, or translated into any language or computer language, in any form or by
any means, electronic, mechanical, magnetic, optical, chemical, manual or oth­erwise, without the prior written permission of PLANET.

PLANET makes no representations or warranties, either expressed or implied,

with respect to the contents hereof and specically disclaims any warranties,
merchantability or tness for any particular purpose. Any software described

in this manual is sold or licensed "as is". Should the programs prove defective
following their purchase, the buyer (and not PLANET, its distributor, or its dealer)
assumes the entire cost of all nec-essary servicing, repair, and any incidental or
consequential damages resulting from any defect in the software. Further, PLANET
reserves the right to revise this publication and to make changes from time to time
in the contents hereof without obligation to notify any person of such revision or
changes.

All brand and product names mentioned in this manual are trademarks and/or
registered trademarks of their respective holders.

Trademarks

PLANET is a registered trademark of PLANET Technology Corp.

All other trademarks belong to their respective owners.

Disclaimer

PLANET Technology does not warrant that the hardware will work properly in all
environments and applica-tions, and makes no warranty and representation, either
implied or expressed, with respect to the quality, performance, merchantability, or

tness for a particular purpose.

PLANET has made every effort to ensure that this User’s Manual is accurate;
PLANET disclaims liability for any inaccuracies or omissions that may have
occurred. Information in this User’s Manual is subject to change without notice
and does not represent a commitment on the part of PLANET. PLANET assumes
no respon-sibility for any inaccuracies that may be contained in this User’s Manual.
PLANET makes no commitment to update or keep current the information in this
User’s Manual, and reserves the right to make improvements to this User’s Manual
and/or to the products described in this User’s Manual, at any time without notice.

If you nd information in this manual that is incorrect, misleading, or incomplete,

we would appreciate your com-ments and suggestions.

FCC Warning

This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful inter-ference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the Instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.

CE Mark Warning

This is a Class A product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.

WEEE Warning

To avoid the potential effects on the environment and human health as a
result of the presence of hazardous substances in electrical and electronic
equipment, end users of electrical and electronic equipment should

understand the meaning of the crossed-out wheeled bin symbol. Do not
dispose of WEEE as unsorted mu-nicipal waste and have to collect such WEEE
separately.

Revision

PLANET 8-Port 10/100TX 802.3at PoE + 2-Port 10/100TX Desktop Switch User's
Manual

For Model: FSD-1008HP

Revision: 1.0 (September 2017)

Part No.: EM-FSD-1008HP_v1.0

Table Of Contents

1. Introduction ............................................................................................... 5

1.1 Checklist ............................................................................................. 5

1.2 Product Description .............................................................................. 5

1.3 Features ............................................................................................. 6

1.4 Specications ...................................................................................... 7

2. Hardware Description .................................................................................. 9

2.1 Front Panel ......................................................................................... 9

2.1.1 LED Indicators ..........................................................................11

2.2 Rear Panel .........................................................................................11

3. Hardware Installation .................................................................................12

3.1 Desktop Installation ............................................................................ 13

3.2 Rack Mounting ...................................................................................14

3.3 Wall Mounting Installation ...................................................................15

4. Troubleshooting .........................................................................................17

Appendix A - 10/100Mbps, 10/100BASE-TX ......................................................18

1. Introduction

1.1 Checklist

Check the contents of your package for the following parts

FSD-1008HP x 1 User’s Manual x 1

Power Cord x 1 Rubber Feet x 4

Rack-mounting Brackets Screws Package x 8

If any of these pieces are missing or damaged, please contact your dealer
immediately; if possible, retain the carton including the original packing material,
and use them again to repack the product in case there is a need to return it to us
for repair.

1.2 Product Description

To fulll the demand of sufcient PoE power for network applications, PLANET

FSD-1008HP 8-Port 10/100TX 802.3at PoE + 2-Port 10/100TX Desktop Switch, a
new member of the 802.3at PoE Fast Ethernet Switch family, features up to 30

5

watts of power output for each port and a total PoE budget of 120 watts for eight
10/100Mbps TP ports, and two 10/100Mbps uplink ports. The eight 802.3at PoE+
ports provide PoE power injector function which is able to drive 8 IEEE 802.3at
compliant powered devices. The FSD-1008HP also provides a simple, cost-effective,
and non-blocking wire-speed performance with 9-inch metal housing suitable for
desktop deployment for SOHO and department network applications.

All RJ45 copper interfaces in the FSD-1008HP support 10/100Mbps auto­negotiation for optimal speed de-tection through RJ45 Category5, 5e or 6 cables. It
also supports standard auto-MDI/MDI-X that can detect the type of connection to
any Ethernet device without requiring special straight-through or crossover cables.

1.3 Features

 Physical Port

z 10-port 10/100BASE-TX Fast Ethernet RJ45 copper

z 8-port IEEE 802.3at/af PoE Injector (Port-1 to Port-8)

 Power over Ethernet

z Complies with IEEE 802.3af/at Power over Ethernet end-span PSE

z Up to 8 ports of IEEE 802.3af/802.3at devices powered

z Supports PoE Power up to 30.8 watts for each PoE port

z Each port supports 55V DC power to PoE powered device

z 120-watt PoE budget

z Auto detects powered device (PD)

z Circuit protection prevents power interference between ports

z Remote power feeding up to 100m in standard mode with 250m in extended

mode

 Switching

z Hardware-based 10/100Mbps auto-negotiation and auto MDI/MDI-X

z Flow control for full duplex operation and back pressure for half duplex opera-

tion

z IEEE 802.1Q VLAN transparency

z Hardware DIP switch for Standard, VLAN and Extend mode selection; the

Extend mode features 30-watt PoE transmit distance of 250m at speed of
10Mbps and VLAN isolation (Only for Port-1 to Port-8)

z Solid DIP switch to isolate ports to prevent broadcast storm and defend DHCP

spoong

6

 Hardware

z 9-inch desktop size, 1U height, rack mountable

z LED indicators for system power, per port PoE ready and PoE activity, speed,

Link/Act

z Fanless design

z Supports Energy-Efcient Ethernet (EEE) function (IEEE 802.3az)

1.4 Specications

Model FSD-1008HP

Hardware Specications

Copper Port 10 10/100/BASE-TX MDI/MDIX Ports

PoE Injector Port

Switch Architecture Store-and-Forward

Switch Fabric 2Gbps/non-blocking

Switch Throughput@64 bytes 1.48Mpps@64 bytes

MAC Address Table

Maximum Frame Size 1522 bytes

Flow Control

LED

DIP Switch

Dimensions (W x D x H) 220 x 150 x 43 mm (1U height)

8-port with 802.3at/af PoE injector function with
Port-1 to Port-8

8K entries, automatic source address learning
and aging

IEEE 802.3x pause frame for full-duplex
Back pressure for half-duplex

System:

 Power (Green)

10/100BASE-TX RJ45 interfaces:

 10/100Mbps LNK/ACT (Green)

PoE interfaces:

 PoE-in-Use (Orange)

Selectable operation mode

 Standard
 VLAN
 Extend

Enclosure Metal

7

Weight 1230 g

Power Requirements AC 100~240V, 50/60Hz, 2.5A max

Power Consumption/Dissipation Max. 120 watts/409.4 BTU

Thermal Fan Fanless

Power over Ethernet

PoE Standard

PoE Power Supply Type End-span

PoE Power Output Per port 55V DC, 540mA. max. 30 watts

Power Pin Assignment 1/2(+), 3/6(-)

PoE Power Budget 120 watts

Max. Number of Class 2 PDs 8

Max. Number of Class 3 PDs 8

Max. Number of Class 4 PDs 8

Standards Conformance

Regulatory Compliance FCC Part 15 Class A, CE

Standards Compliance

Environment

Operating

IEEE 802.3af Power over Ethernet/PSE
IEEE 802.3at Power over Ethernet Plus/PSE

IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3x Flow control and back pressure
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet Plus

IEEE 802.3az Energy Efcient Ethernet (EEE)

Temperature: 0 ~ 50 degrees C
Relative Humidity: 5 ~ 95% (non-condensing)

Storage

8

Temperature: -10 ~ 70 degrees C
Relative Humidity: 5 ~ 95% (non-condensing)

2. Hardware Description

The switch provides two different running speeds – 10Mbps and 100Mbps, and
automatically distinguishes the speed of the incoming connection.

This section describes the hardware features of the FSD-1008HP. For easier
management and control of the FSD-1008HP, familiarize yourself with its display
indicators and ports. Front panel illustrations in this chapter display the unit LED
indicators. Before connecting any network device to the FSD-1008HP, please read
this chapter carefully.

2.1 Front Panel

The Front Panel of the FSD-1008HP PoE+ Ethernet Switch consists of 10 Auto­Sensing 10/100Mbps Ethernet RJ45 Ports. The LED Indicators are also located on
the front panel of the FSD-1008HP.

FSD-1008HP

4 6 82

4 8

2 6

PWR

1

53 7

ACTLNK

PoE In-Use

PoE

9 10

PoE

Standard

Extend

VLAN

1 3 5 7 9

8-Port 10/100TX 802.3at PoE +
2-Port 10/100TX Desktop Switch

Uplink

10

Figure 2-1: FSD-1008HP Switch Front Panel

The front panel of FSD-1008HP provides one DIP switch for Standard, VLAN
and Extend mode selections. The detailed descriptions are shown in the following
table.

DIP Switch Mode Function

This mode makes the FSD-1008HP operate as a general

Standard

VLAN

Extend

switch and all PoE ports operate at 10/100Mbps auto­negotiation.

This mode makes the FSD-1008HP operate as a VLAN
isolation switch and

Standard

VLAN

Extend

1. Port 1 to port 8 will isolate respectively.

2. Port 1 to port 8 can only communicate with port 9 and
port 10 (uplink port).

9

Standard

Standard

VLAN

Extend

Standard

VLAN

Extend

Standard

VLAN

Extend

VLAN

Extend

Note

Power

This mode makes the FSD-1008HP operate as a VLAN
isolation switch and

1. Port 1 to port 8 will isolate respectively.

2. Port 1 to port 8 can only communicate with port 9 and
port 10 (uplink port).

3. 30-watt PoE transmit distance of 250m at speed of 10Mbps.

Please reboot the FSD-1008HP after adjusting the DIP switch.

Default PoE Mode

PoE IP Camera

PoE

FSD-1008HP

100 meters (328 feet)

VLAN Isolation Mode

NVR

Port 9 and Port 10
Access Permitted

PoE

PoE

PoE

IP Camera

IP Camera

IP Camera

Ports 1 to 8

Access Denied

10

FSD-1008HP

Power

FSD-1008HP

Extended PoE Mode

PoE

250 meters (820 feet)

PC

PoE IP Camera

PoE

PoE

10BASE-T UTP with PoE

100BASE-TX UTP

100BASE-TX UTP with PoE

2.1.1 LED Indicators

System

LED Color Function

PWR Green Lights to indicate that the Switch has power.

Per 10/100Mbps Port

LED Color Function

PoE-in-use Orange

Lights to indicate the port is providing 55V DC in-line
power. (1-8 ports)

Lights to indicate the Switch is successfully connecting to

Speed/

LNK/ACT

Green

the network at 10/100Mbps.
Blinks to indicate that the Switch is actively sending or
receiving data over that port.

2.2 Rear Panel

The rear panel of the FSD-1008HP has an AC inlet power socket, which accepts
input power of 100 to 240V AC, 50-60Hz.

100-240V AC

50/60Hz

Figure 2-2: FSD-1008HP Switch Rear Panel

1. The device is a power-required device which means it will not
work till it is powered. If your networks should be active all the
time, please consider using UPS (Uninterrupted Power Supply)
for your device. It will prevent you from network data loss or

Power

Note

network downtime.

2. In some areas, installing a surge suppression device may also
help to protect your FSD-1008HP from being damaged by
unregulated surge or current to the FSD-1008HP.

11

3. Hardware Installation

Start up

Please refer to the following for your cabling:

 10/100BASE-TX

All 10/100BASE-TX ports come with Auto-Negotiation capability. They automatically
support 100BASE-TX and 10BASE-T networks. Users only need to plug a working
network device into one of the 10/100 BASE-TX ports, and then turn on the FSD­1008HP. The port will automatically run in 10Mbps, 20Mbps, 100Mbps or 200Mbps
after the negotiation with the connected device.

 Cabling

Each of the 10/100BASE-TX ports uses RJ45 sockets -- similar to the phone jacks

-- for connection of un-shielded twisted-pair cable (UTP). The IEEE 802.3/802.3u
Fast Ethernet standard requires Category 5 UTP for 100Mbps 100BASE-TX.
10BASE-T networks can use Cat.3, 4, 5 or 6 UTP (see table below). Maximum
distance is 100 meters (328 feet).

Port Type Cable Type Connector

10BASE-T Cat.3, 4, 5, 2-pair RJ45

100BASE-TX Cat.5, 5e UTP, 4-pair RJ45

Any Ethernet devices like hubs/PCs can be connected to the FSD-1008HP by using
straight-through wires. The whole 10/100Mbps ports are auto-MDI/MDI-X that can
be used on straight-through or crossover cable.

12

3.1 Desktop Installation

To install the FSD-1008HP on desktop, simply follow the following steps:

Step 1: Attach the rubber feet to the recessed areas on the bottom of the FSD-

1008HP, as shown in Figure 3-1.

FSD-1008HP

2 6

4 8

PoE In-Use

PoE

PWR

1

53 7

9 10

PoE

Standard

ACTLNK

VLAN

Extend

4 6 82

1 3 5 7 9

8-Port 10/100TX 802.3at PoE +
2-Port 10/100TX Desktop Switch

Uplink

10

Figure 3-1: Attaching the Rubber Feet to the FSD-1008HP

Step 2: Place the FSD-1008HP on desktop near an AC power source.

Step 3: Keep enough ventilation space between the FSD-1008HP and the

surrounding objects.

When choosing a location, please keep in mind the environmental
restrictions discussed in Chapter 1, Section 4, under Specifications.

Note

Step 4: Connect your FSD-1008HP to 802.3af/802.3at complied power devices

(PD) and other network devices

A. Connect one end of a standard network cable to the 10/100BASE-TX RJ45

ports on the front panel of the FSD-1008HP.

B. Connect the other end of the cable to the network devices such as printer

servers, workstations, routers, etc.

Note

Connection to the Switch requires UTP Category 5, 5e, 6 network
cabling with RJ45 tips.

13

Step 5: Supply power to the FSD-1008HP.

A. Connect one end of the power cable to the FSD-1008HP.

B. Connect the power plug of the power cable to a standard wall outlet.

When the FSD-1008HP receives power, the Power LED should remain solid Green.

3.2 Rack Mounting

To install the FSD-1008HP in a 19-inch standard rack, follow the instructions
described below.

Step 1: Place your FSD-1008HP on a hard at surface, with the front panel

positioned towards your front side.

Step 2: Attach a rack-mount bracket to each side of the FSD-1008HP with

supplied screws attached to the package. Figure 3-2 shows how to attach
brackets to one side of the FSD-1008HP.

FSD-1008HP

2 6

PWR

1

4 6 82

4 8

ACTLNK

PoE In-Use

PoE

53 7

9 10

PoE

Standard

VLAN
Extend

1 3 5 7 9

8-Port 10/100TX 802.3at PoE +
2-Port 10/100TX Desktop Switch

Uplink

10

Figure 3-2: Attaching the Brackets to the FSD-1008HP.

You must use the screws supplied with the mounting brackets.
Damage caused to the parts by using incorrect screws would invali­date the warranty.

Step 3: Secure the brackets tightly.

Step 4: Follow the same steps to attach the second bracket to the opposite side.

14

Step 5: After the brackets are attached to the FSD-1008HP, use suitable screws to

securely attach the brackets to the rack, as shown in Figure 3-3.

4 6 82

2 6

4 8

ACTLNK

PoE In-Use

PoE

PWR

1

53 7

FSD-1008HP

9 10

PoE

Standard

VLAN
Extend

1 3 5 7 9

8-Port 10/100TX 802.3at PoE +
2-Port 10/100TX Desktop Switch

Uplink

10

Figure 3-3: Mounting the FSD-1008HP in a Rack

Step 6: Proceed with Steps 4 and 5 of session 3.1 Desktop Installation to connect

the network cabling and supply power to your Switch.

3.3 Wall Mounting Installation

Step 1: Please nd the wall that can mount the FSD-1008HP.

Step 2: Install two screws on the wall.

Step 3: Hang the FSD-1008HP on the screws from the wall.

Step 4: Repeat step 5 of Desktop Installation for power supply to the FSD-

1008HP.

Before mounting the device to the wall, please check the location

Note

of the electrical outlet and the length of the Ethernet cable.

15

150mm

FSD-1008HP Switch Bottom Side

50/60Hz, 1.5A

100-240V AC

RJ45
UTP Cable

16

4. Troubleshooting

This chapter contains information to help you solve issues. If the FSD-1008HP
is not functioning properly, make sure the FSD-1008HP was set up according to
instructions in this manual.

Q1: The Link LED is not lit.

Solution:

Check the cable connection and also try to swap one new cable.

Q2:100BASE-TXportlinkLED islit,butthetrafcisirregular.

Solution:

Make sure the attached device is not set to full duplex. Some devices use a
physical or software switch to change duplex modes. Auto-negotiation may not
recognize this type of full-duplex setting.

Q3: Why the Switch isn’t connected to the network.

Solution:

Check the LNK/ACT LED on the FSD-1008HP. Try another port on the FSD-1008HP.
Make sure the cable is installed properly. Make sure the cable is the right type.
Turn off the power. After a while, turn on the power again

Q4: Why the FSD-1008HP, connected to PoE device, cannot be

powered on.

Solution:

Please check the cable type of the connection from the FSD-1008HP to the other
end. The cable should be an 8-wire UTP, Category 5 or above and EIA568 cable
within 100 meters. A cable with only 4-wire, short loop or over 100 meters will
affect the power supply.

Please make sure the device is fully complied with IEEE 802.3af/IEEE 802.3at
standard.

Q5: What is the power output of each PoE port?

Solution:

1. Each PoE port supports 53-55V DC, 540mA and a maximum of 30 watts of
power output. Detect and inject by the standard of IEEE 802.3at.

2. Each PoE port supports 53-55V DC, 290mA and a maximum of 15.4 watts of
power output. Detect and inject by the standard of IEEE 802.3af.

17

Appendix A - 10/100Mbps, 10/100BASE-TX

When connecting Switch to another Fast Ethernet switch, a straight-through or
crossover cable might be necessary. Each port of the Switch supports auto-MDI/
MDI-X detection, meaning you can directly connect the Switch to any Ethernet
devices without making a crossover cable. The following table and diagram show
the standard RJ45 receptacle/connector and their pin assignments:

RJ45 Connector Pin Assignment

Contact

1 Tx + (transmit) Rx + (receive)

2 Tx - (transmit) Rx - (receive)

3 Rx + (receive) Tx + (transmit)

4, 5 Not used

6 Rx - (receive) Tx - (transmit)

7, 8 Not used

The standard cable, RJ45 pin assignment

Media Dependent Interface

MDI

Media Dependent Interface-Cross

The standard RJ45 receptacle/connector

MDI-X

18

There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The
following shows the pin allocation and color of straight-through cable and crossover
cable connection:

Straight Cable

12345678

12345678

SIDE 1

SIDE 2

SIDE 1

1 = White/Orange
2 = Orange
3 = White/Green
4 = Blue
5 = White/Blue
6 = Green
7 = White/Brown
8 = Brown

SIDE 2

1 = White/Orange
2 = Orange
3 = White/Green
4 = Blue
5 = White/Blue
6 = Green
7 = White/Brown
8 = Brown

Cross Over Cable

12345678

12345678

SIDE 1

SIDE 2

SIDE 1 SIDE 2

1 = White/Orange
2 = Orange
3 = White/Green
4 = Blue
5 = White/Blue
6 = Green
7 = White/Brown
8 = Brown

1 = White/Green
2 = Green
3 = White/Orange
4 = Blue
5 = White/Blue
6 = Orange
7 = White/Brown
8 = Brown

Figure A-1: Straight-through and Crossover Cable

Please make sure your connected cables are with the same pin assignment and
color as the above description before deploying the cables into your network.

19