MII Module
FS3-MTX / FS3-MSC
10Base-T/100Base-TX / 100BASE-FX MII Module
Quick Installation Guide
FS3-MTX/FS3-MSC
FCC Information
The Federal Communication Commission Radio Frequency Interference Statement includes the
following paragraph:
This equipment has been tested and found to comply with the limits for a Class B Digital Device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communication. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
♦ Reorient or relocate the receiving antenna.
♦ Increase the separation between the equipment and receiver.
♦ Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
♦ Consult the dealer or an experienced radio / TV technician for help.
The user should not modify or change this equipment without written approval from company
name. Modification could void authority to use this equipment.
For the safety reason, people should not work in a situation which RF Exposure limits be
exceeded. To prevent the situation happening, people who work with the antenna should be
aware of the following rules:
1. Install the antenna in a location where a distance of 6.5 cm from the antenna may be
maintained.
2. While installing the antenna in the location, please do not turn on the power of wireless
card.
While the device is working, please do not contact the antenna.
Copyright
Copyright © 1999 Planet Technology Corp., all rights reserved. No part of this publication may be
reproduced, adapted, stored in a retrieval system, translated into any language, or transmitted in any
form or by any means without the written permission of Planet Technology Corp.
Contents subject to revision without prior notice.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
About This Manual
MII Module FS3-MTX / FS3-MSC Quick Installation Guide is first published by Planet Technology
Corp. in 1999. This Revision is issued in August , 1999. The purpose of this manual is for the setup
of the product MII Module FS3-MTX / FS3-MSC.
Revision
MII Module FS3-MTX / FS3-MSC Quick Installation Guide
Part No. EMQ-FS3MTX
Quick Installation
Module Overview
Model No. FS3-MTX FS3-MSC
Network Protocols IEEE 802.3u
Cable Category 5 cable multi-mode fiber optic (MMF)
Connector RJ-45 Duplex SC
Duplex Mode support Half / Full Half / Full
Other Auto-negotiation
10BASE-T/
100BASE-TX
Specification
u FS3-MTX
MEDIA 10BASE-T/100BASE-TX
PHY
ADDRESS
SWITCH
PHY address is 5-bit number. Bit 0 is LSB and bit 4 is MSB.
See the following figure. The left side represents 0 and the
right side represents 1. The figure shows the default value
00000 in binary.
0 1
0
1
2 PHY Address
3
4
IEEE 802.3u
100BASE-FX
cable
MDI/MDI-X
BUTTON
100 100BASE-TX Port Status LED:
10 10BASE-T Port Status LED:
FDX/COL Duplex Mode and Collision LED:
ACT Port Activity LED:
MDI-X : Button up. It represents normal port of switches or
repeaters.
MDI : Button down. It represents crossover port of switches
or repeaters and normal port of NIC cards.
MDI-X MDI
Green: 100M Link successfully.
Green: 10M Link successfully.
Green blinking: happen collision in half duplex.
Continuously on(green): full duplex.
Green blinking: network traffic.
1
u FSp3-MSC
0
1
2
PHY Address
HALF
MEDIA 100BASE-FX, wavelength is 1300nm
PHY
ADDRESS
SWITCH
PHY address is 5-bit number. Bit 0 is LSB and bit 4 is MSB.
See the following figure. The left side represents 0 and the
right side represents 1. The figure shows the default value
00000 in binary.
0 1
3
4
FS3-MTX/FS3-MSC
FULL
HALF/FULL
SWITCH
100 100BASE-TX Port Status LED:
FDX/COL Duplex Mode and Collision LED:
ACT Port Activity LED:
CABLE 62.5/125 microns multi-mode fiber optic cable with duplex
The duplex switch locates below bit 4 of PHY address as the
previous figure. Switching to left side represents full duplex
and switching to right side represents half duplex. Default is
full duplex mode. 200Mbps full duplex can reach maximum
distance 2km (6562 ft.).
Green: 100M Link successfully.
Green blinking: happen collision in half duplex.
Continuously on(green): full duplex.
Green blinking: network traffic.
SC connector.
How to Install
u FS3-MTX
Case 1: If your switch is FS3-1600, then
(1) Keep the PHY Address value on default value (00000). FS3-MTX is a 10BASE-
T/100BASE-TX MII module that complies fully with all IEEE 802.3u specifications.
FS3-MTX can provide half duplex, full duplex and auto-negotiation modes over
Category 5 cable with RJ-45 connector.
(2) Insert FS3-MTX module into the MII interface and make sure it’ s connection is solid.
Then it can work normally via Planet unique hot-swappable technique.
2
Case 2: If you use other switch or repeater with MII interface, then
(1) Please turn off the power of the switch or repeater HUB.
(2) Set up the desired PHY address by manually setting the PHY address switch
mentioned above.
(3) Insert FS3-MTX module into the MII interface and make sure it’ s connection is solid.
(4) Turn on the power of the switch or repeater HUB, and it can work normally.
Connection Devices and Required Cable
Connection Device Required Cable Distance
Normal Port of Hubs and
Switches
Crossover Port of Hubs
Crossover Category 5 Cable
Normal Category 5 Cable
100 meters
maximum
and Switches
NIC Cards Normal Category 5 Cable
u FS3-MSC
Case 1: If your switch is FS3-1600, then
(5) Keep the PHY Address value on default value (00000).
(6) Set up the duplex mode in full duplex.
(7) Insert FS3-MSC module into the MII interface and make sure it’ s connection is solid.
Then it can work normally via Planet unique hot-swappable technique.
Case 2: If you use other switch or repeater with MII interface, then
(8) Please turn off the power of the switch or repeater HUB.
(9) Set up the desired PHY address by manually setting the PHY address switch
mentioned above.
(10) Set up the duplex mode. If the module is connected to a repeater, please switch to half
duplex mode. Otherwise, please keep the default mode (full duplex).
(11) Insert FS3-MSC module into the MII interface and make sure it’ s connection is solid.
(12) Check the duplex mode of the other port that will be connected to FS3-MSC. Make sure
3
FS3-MTX/FS3-MSC
that duplex modes of both sides are the same.
(13) Turn on the power of the switch or repeater HUB, and it can work normally.
Duplex SC MMF Connection
RX TX
TX RX
Duplex SC MMF Cable
FS3-MSC FS3-MSC
Connection Devices and Required Cable
Connection Device Required Cable Distance
SC fiber port of FS3MSC
62.5um/125um,
Multi-mode optic
fiber cable
Full duplex: 2Km maximum
Half duplex: 412 meters
maximum
Part No. EMQ-FS3MTX
4
Loading...