Planar ND1950, ND1750 User Manual

Contents
Preface ................................................................................................................2
Installation ...........................................................................................................4
Unpacking ...............................................................................................................................................................................4
Desktop Installation.............................................................................................................................................................4
Connecting the Network Display and Base................................................................................................................4
Viewing Angle Adjustment...............................................................................................................................................4
Alternate Mounting Solutions.........................................................................................................................................5
Detaching Network Display from Its Stand ................................................................................................................5
Interface for Arm/ Wall Mount Applications ..............................................................................................................5
Connecting the Display to Your Network ...................................................................................................................5
Connecting User Devices...................................................................................................................................................6
Connecting the AC Power.................................................................................................................................................6
Setting Up the Network Display .....................................................................................................................................6
Display Controls ..................................................................................................7
User Controls..........................................................................................................................................................................7
Power Modes..........................................................................................................................................................................8
Adjusting the Display.......................................................................................................................................................... 8
Function Description...........................................................................................................................................................8
Technical Information ..........................................................................................9
Specifications .........................................................................................................................................................................9
Supported Display Resolutions.................................................................................................................................... 10
Troubleshooting.................................................................................................11
End User License Agreement (“License”).........................................................12
1
Preface
This manual is designed to assist users in setting up and using the Integrated Thin Client Network Display (Network Display). Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic or other means, in any form, without prior permission of the manufacturer.
FCC Statement Warning
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reposition or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced monitor technician for help.
Warning
Use only shielded signal cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
This device complies with part 15 FCC Rules. Operation is subject to the following two conditions (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.
Canadian DOC Notice
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
2
Important Safety Instructions
Please read the following instructions carefully. This manual should be retained for future use.
1. To clean the Network Display screen;
-- Power off the Network Display and unplug the AC Cord.
-- Spray a non-solvent cleaning solution onto a soft cloth.
-- Gently clean the screen with dampened cloth.
2. Do not place the Network Display near a window. Exposing the display to rain water, moisture or sunlight can severely damage it.
3. Do not apply pressure to the LCD screen. Excess pressure may cause permanent damage to the display.
4. Do not remove the cover or attempt to service this unit yourself. Servicing of any nature should be
performed by an authorized technician.
5. Store (not connected to the AC power source) the Network Display in a room with a room temperature of
-20° ~ 60°C (or -4° ~ 140°F). Storing the Network Display outside this range could result in permanent damage.
6. If any of the following occurs, immediately unplug your monitor and call an authorized technician.
AC Power cable is frayed or damaged.
Liquid is spilled into the Network Display or it has been exposed to rain.
LCD display or the Network Display case is damaged.
7. Only use the supplied main lead (AC Power Cord) to connect the monitor. For a nominal current up to 6A and a device weight above 3 kg, a line not lighter than H05VV-F, 3G, 0.75 mm
Important Recycle Instruction:
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. FOR MORE INFORMATION, CONTACT THE ELECTRONIC INDUSTRIES ALLIANCE AT WWW.EIAE.ORG. WWW.LAMPRECYCLE.ORG.
FOR LAMP SPECIFIC DISPOSAL INFORMATION CHECK
2
must be used.
Contains Mercury, Dispose of Properly
3
Installation
Unpacking
Before unpacking the Network Display, prepare a suitable workspace for your Monitor and computer. You need a stable and clean surface near a wall power outlet. Make sure that Network Display has enough space around it for sufficient airflow. Though the Network Display uses very little power, some ventilation is needed to ensure that the Monitor does not become too hot. After you unpack the Network Display, make sure that the following items were included in the box:
Network Display ● User's Guide ● Desk Stand Base
Power Cord ● USB Keyboard ● PS2 Mouse
If you find that any of these items are missing or appear damaged, contact Planar immediately.
Register Your Planar Products Today Thank you for choosing Planar. To assure you receive all the benefits of your Planar product and services, register your Planar product today. Visit our website to register your product at
http://www.planar.com/support/product_registration.html
Cables, Replacement Lamps and Accessories To find cables, replacement lamps and accessories for your Planar projector, LCD monitor, touchscreen or other Planar products visit our online store at www.PlanarOnline.com or find other stores who carry Planar products at http://www.planar.com/howtobuy
Desktop Installation
Connecting the Network Display and Base
When you open the box to take the base and put on the desk first. Then connect the Network Display and base please.(See fig.1-1 )
Figure 1-1
Viewing Angle Adjustment
The Network Display is designed to allow users to have a comfortable viewing angle. The viewing angle can be adjusted from -5°to +20°.(See fig. 1-2)
Figure 1-2
Warning
Do not force the Network Display over its maximum viewing angle settings as stated above. Attempting to do so will result in damaging the Network Display and Display Stand.
4
Alternate Mounting Solutions
Detaching Network Display from Its Stand
Unscrew screws n the swivel base support column and pull downo the hinge to release.
Interface for Arm/ Wall Mount Applications
Before installing to mounting device, please refer to Fig.1-3. The rear of this LCD display has four integrated 4 mm, 0.7 pitch threaded nuts, as well as four 5 mm access holes in the plastic covering as illustrated in Figure 1-4. These specifications meet the VESA Flat Panel Monitor Physical Mounting Interface Standard (paragraphs 2.1 and 2.1.3, version 1, dated 13 November 1997).
Note: M4mm x 11mm (L) screws should be used for a 3mm thick mounting plate application. Thicker plates should use appropriately longer screws. The screw threads should extend between 8 and 10 mm beyond the display surface of the mounting plate. Follow the mounting device manufacturer’s reccomendations.
Connecting the Display to Your Network
1. Make sure the AC Power Cord is disconnected
2. Connect one end of the Ethernet cable to the Network Display’s
Ethernet (ENET) port. (See Fig 1-5)
3. Verify that the other end of the Ethernet cable is connected to
your LAN/WAN network.
4. Make sure connections are secure and that the Ethernet
connectors have “clicked” into place.
Figure 1-3
Figure 1-4
Figure1-5
5
Connecting User Devices
1. USB devices such as the Keyboard can be connected to ports on
the side or bottom (See Fig. 1-6 and Figure 1-7)
2. The unit may be secured through the use of Kensington locking
devices. (See Figure 1-6)
3. The Headset/Handset port (RJ22) is reserved for future
use with VOIP software support tools. It is designed for connection to analog telephone headsets or handsets. We recommend only the use of a UL or other safety agency approved device.
Caution: This is not a telephone modem connection and should not be connected to a telephone line. Damage to the unit might occur.
4. The PS2 Mouse connects to the PS2 connector on the right end
of the keyboard.
Figure 1-6
5. A stereo headphone may be connected to the front of the
Network Display
Figure 1-7
Connecting the AC Power
1. Connect the power cord to the AC adapter (See Fig. 1-8)
2. Connect the AC adapter’s DC output connector to the DC
Power Jack of the display.
3. Connect the power cord to a 100-240 VAC, 50/60Hz power
source.
Figure 1-8
Setting Up the Network Display
1. Make sure the AC power cord is connected to the Power Adapter.
2. Press the Network Display's power switch, located on the bezel of the monitor. (See Figure 2-1)
3. After power-on, the thin client will boot and commence a series of tests and communication checks which
will be shown in the System Information Event Log.
4. For the Network Display to properly connect to your network and applications servers, the Network Display
and your network environment must be appropriately configured. Please contact your Information Technology specialist for further details.
5. A detailed User Guide and Administrators Guide for the Wyse Thin Client Operating System (WTOS) may be
obtained at http://www.planar.com/support/
for this product model number.
6
Display Controls
User Controls
A brief description and the location of all Network Display functions controls and indicators:
54
Power Control - LED
1
2
3
4
5
Modes are changed by pressing the Power Control Button (Please refer to Figure 2-2)
Brightness Function / Adjust increase
Brightness Function / Adjust decrease
Audio Volume Function / Adjust increase
Audio Volume Function / Adjust decrease
1
Figure 2-1
32
7
Power Modes
The Network Display has three modes of operation.
Figure 2-2
The following assumes the AC Power Adapter is connected to the display and an AC power source.
Power Mode LED Operation Description
Power button is pressed for 3 Sec while in Standby mode (Thin client is switched off)
1
2
Off
Run
Power button is pressed for 3 Sec while in Run mode (Thin client
Dark
Green
and display are switched off)
Caution: Be very careful to not turn off the Display while the operating system is downloading a software update!
If the Power button is momentarily pressed when in the Off mode the display is powered and the thin client will boot.
If the Power button is momentarily pressed while in Standby mode, the display returns to Run mode.
3
Standby
Yellow
If the Power button is momentarily pressed while in Run mode the display is turned off while the Thin Client continues to operate. This mode can be used for privacy or to conserve power.
Adjusting the Display
The monitor has four function control buttons designed for comfortable viewing and listening.
Function Description
Icon Function Function Description
Brightness
Audio Volume
The brightness of the display may be varied.
The volume of the speakers and headphone may be varied.
8
Technical Information
Specifications
LCD Panel ND1750 ND1950 Size 17" SXGA 19” SXGA Display Type Active matrix color TFT LCD Active matrix color TFT LCD Resolution 1280 x 1024 1280 x 1024 Display Dot 1280 x (RGB) x 1024 1280 x (RGB) x 1024 Aspect Ratio 5:4
Display Area , mm (H x V) 337.92 mm (H) x 270.34 mm (V) 376.32 mm (H) x 301.6 mm (V) Displayed Colo rs Up to16. 2M with FRC or Dithering Up to 16. 2M with FRC or Dithering Brightness 300 cd/m2 (typical) 300 cd/m2 (typical Contrast Ratio 800:1 (typical) 800:1 (typical) Response Time 5ms (typical) 5ms (typical) Color Temperature 6500°K, Factory Calibrated 6500°K, Factory Calibrated
Controls
Power Switch (Momentary) Power Mode control with LED indicator Brightness 2 buttons Audio 2 buttons
Audio
Input Microphone Level, Monophonic Speaker Output 0.5W + 0.5W
OSD
Brightness Digital Volume
Digital
Power Management
Power Mode Power Consumption* Power LED Color
Run 60 W maximum
(DC output, 12V/5A) ND1750: 36 W, typical ND1950: 40 W, typical
Standby 12 W maximum
10 W typical
Off 1 W maximum Dark
Green
Yellow
5:4
9
External Connections
Power Input (DC input) DC Socket, 12V, 5A (Center Positive) GigaBit Ethernet port RJ45 USB ports 4 x USB connectors, Type A Receptacles Headphone 3.5mm Stereo Jack Microphone 3.5mm Mono Jack, Pink Headset RJ22 (4P4C, Reserved for Future VOIP Software Support)
Environment
Operating Condition:
Storage Condition:
Temperature Relative Humidity Temperature Relative Humidity
5°C to 40°C/41°F to 104°F 20% to 80%
-20°C to 60° C/-4°F to140° F 5% to 85%
Power Supply (AC Input)
Input Voltage Single phase, 100 ~ 240VAC, 50 / 60 Hz Input Current 1.5 A maximum
Size and Weight ND1750 ND1950
Dimensions 367 (W) x 384 (H) x 199 (D) mm 413 (W) x 418 (H) x 222 (D) mm Net Weight 4.5 kg 4.6 kg Gross Weight 7.7 kg 8.0 kg
Supported Display Resolutions
If the selected timing is NOT included in table below, the Network Display will use the most suitable available timing.
Mode Resolution
(Horizontal X Vertical)
SXGA 1280 X 1024
XGA 1024 X 768
SVGA 800 X 600
VGA 640 X 480
10
Troubleshooting
This Network Display has been pre-adjusted using factory standards.
PROBLEM There is no image on Network Display
If there’s no image on the Network Display, please perform the following steps:
1. Verify that the power cord is connected to a proper source of power.
2. Verify that the power cord is fully connected to the Power Adapter and that the Power Adapter cord is fully connected to the DC connector on the rear of the Display. The LED on the Power Adapter should be green.
3. Verify that the Power Indicator on the Network Display is green.
4. Turn off the Network Display and then turn it back on again.
PROBLEM The displayed image is dim.
If the displayed image on the Display appears too dim:
1. Press the Brightness Control
PROBLEM The Network Display will not connect to your network.
If the Network Display will not connect to your network, please perform the following steps:
1. Verify that the Ethernet connector is properly connected to your network and to the Display.
2. Verify that your network is live and properly configured for use with the network display.
to increase the brightness.
11
End User License Agreement (“License”)
IMPORTANT – READ CAREFULLY.
THIS LICENSE IS A LEGAL DOCUMENT setting forth the terms under which Planar Systems, Inc. (“Licensor”) and
its licensors and suppliers (collectively referred to as “Third Party Suppliers”) are willing to license to you
software which is owned by Licensor and/or its Third Party Suppliers, who are intended third party beneficiaries
under this License.
Acceptance
described in the manual or other document containing this License, whichever is applicable, (“Software”),
together with any supplied documentation, only if you accept all of the terms contained in this License. Please
read this Agreement carefully before unpacking, downloading, installing or using the Software or the Device
(defined below). By downloading or installing the Software, or unpacking or using the Software or Device, you
agree to be bound by the terms of this License. If you do not agree to these terms, Licensor and its Third Party
Suppliers are unwilling to license the Software to you, and you should not and may not download or install the
Software or unpack or use the Software or the Device. In such case, you should promptly contact Licensor for
information on return of the unused product and all accompanying materials for a refund of your money. ANY
USE OF THE SOFTWARE, INCLUDING BUT NOT LIMITED TO USE ON THE DEVICE, WILL CONSISTUTE YOUR
ACCEPTANCE OF THIS LICENSE (OR RATIFICATION OF ANY PREVIOUS CONSENT).
Grant
Software, in object code only, solely in conjunction with your Planar-manufactured hardware (“Device”). You
have the right to use this Software by loading it onto a computer containing the capability of transferring the
Software (in whole or in part) to the Device. You may use the Software in this fashion as many times as
necessary, so long as such use is always in conjunction with the Device.
Copyright
and intellectual property. All title and copyrights in and to the Software (including but not limited to any
images, photographs, animations, video, audio, music, text and “applets” incorporated into the Software) and
any copies of the Software are owned and retained by Licensor and/or its Third Party Suppliers. You may copy
and use the Software and related documentation only as expressly permitted in this License. You must
reproduce and maintain all proprietary marks, legends, and copyright notices that appear in or on the Software
and related materials, or any portion thereof, on any copies of the Software or related materials that you make
or use. Third Party Suppliers named in such copyright notices shall each have the right to enforce provisions of
this License or use. Third Party Suppliers named in such copyright notices shall each have the right to enforce
provisions of this License.
Patents
following U.S. patents: 6,836,885 and 5,918,039.
Restrictions
whole or in part, except as expressly provided for in this License. You may not sell, rent, lend or lease the
. Licensor is willing to license to you the enclosed software, downloaded software, or software
. Licensor grants to you a non-exclusive right, during the term of this License, to install and/or use the
. The Software and all related documentation are protected under the laws and treaties of copyright
. The Software and/or Device are protected by international treaties and various patents, including the
. You may not use, copy, modify, translate or transfer the Software, or any modification thereof, in
12
Software. You may not decompile, reverse engineer or otherwise decode or alter the Software, or attempt to do
any of the same, except and only to the extent that applicable law notwithstanding this limitation expressly
permits such activity.
Software Transfer
including all of your rights under this License to use the Software, provided you retain no copies, you transfer
the entire product (including the Device and Software, all component parts, the media and printed materials,
any upgrades, these license terms, and, if applicable, the Certificate(s) of Authority), and the recipient accepts
and agrees to the terms and conditions of this License. You may not otherwise sublicense, assign or transfer the
Software or ownership of the Device and equipment. If the Software is an upgrade, any transfer must also
include all previous versions of the Software.
Termination
including any attempt to modify the Software. Upon termination for any reason, you agree to promptly destroy
all copies of the Software and related material or return all such copies to Licensor.
Disclaimer of Warranty
whether express, implied or statutory. LICENSOR SPECIFICALLY DISCLAIMS ALL WARRANTIES,
REPRESENTATIONS, OR CONDITIONS, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR
CONDITION OF MERCHANTABILITY, NONINFRINGEMENT, AND CORRESPONDENCE TO DESCRIPTION OR FITNESS
FOR A PARTICULAR PURPOSE. LICENSOR DOES NOT WARRANT THAT THE FUNCTIONS CONTAINED IN THE
SOFTWARE WILL MEET YOUR REQUIREMENTS OR THAT THE OPERATION WILL BE UNINTERRUPTED OR ERROR
FREE. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES, SO THE ABOVE
EXCLUSION MAY NOT APPLY TO YOU.
LIMITATION OF LIABILITY
DIRECT, CONSEQUENTIAL, INCIDENTAL, INDIRECT, OR SPECIAL DAMAGES, INCLUDING WITHOUT LIMITATION
COST OF COVER, LOST PROFITS, OR LOSSES RESULTING FROM BUSINESS INTERRUPTION OR LOSS OF DATA,
REGARDLESS OF THE FORM OF ACTION OR LEGAL THEORY UNDER WHICH THE LIABILITY MAY BE ASSERTED,
EVEN IF ADVISED OF THE POSSIBILITY OR LIKELIHOOD OF SUCH DAMAGES. SOME JURISDICTIONS DO NOT
ALLOW THE LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, SO THE ABOVE
LIMITATION MAY NOT APPLY TO YOU.
REMEDIES. NOTWITHSTANDING ANY DAMAGES THAT YOU MIGHT INCUR FOR ANY REASON WHATSOEVER (INCLUDING, WITHOUT LIMITATION, ALL DAMAGES REFERENCED ABOVE AND ALL DIRECT OR GENERAL DAMAGES), THE ENTIRE LIABILITY OF LICENSOR AND ANY THIRD PARTY SUPPLIERS UNDER ANY PROVISION
. You may permanently transfer to another party ownership of the Device and equipment,
. This License will terminate automatically if you fail to comply with any of its terms or conditions,
. The Software is provided “AS IS” with all faults and with no warranties of any kind,
. IN NO EVENT SHALL LICENSOR OR ANY THIRD PARTY SUPPLIER BE LIABLE FOR ANY
13
Loading...