Wireless-AC|1200M Repeater/Router/AP
Applicable Model:LV-AC09
LED Explanation
Signal
(Repeater Mode)
The AC MiNi Router is connected to the router or AP, but is
too far away from the router or AP.
The AC MiNi Router is connected to the router or AP, and is
in a good location.
The AC MiNi Router is connected to the router or AP, but is
too far near from the router or AP.
Button and Port Explanation
WPS Button: If your Wireless Adapter supports WPS function, you can press the WPS button and then press
the WPS button to establish a secure connection between the Wireless terminal devices and the AC MiNi Router.
Reset Button: This button is used to restore the AC MiNi Router’s factory default settings. There are two ways to reset the AC MiNi Router:
Option One: With the AC MiNi Router powered on, use a pin press the Reset Button for less than 8 seconds , then release the button and wait the AC MiNi Router to reboot to its factory default settings.
Option Two: Restore the default setting from “Advanced->System->Load default->Load default ” of the AC MiNi Router’s Web-based Management page.
Power on/o Button: This button is used to power on or o the AC MiNi Router.
WAN Port: One 10/100Mbps RJ45 Ethernet port.
In Router mode, it’s used for connecting to the DSL/cable Modem or Internet.
In Repeater/WISP mode, it’s used for connecting to Ethernet-enabled device, working the same as the Ethernet port.
In Access Point mode, it’s used for connecting to front router or Internet.
LAN Port: One 10/100Mbps RJ45 Ethernet port used to add wireless connectivity to an Ethernet-enabled device such as Internet TV, DVR, Gaming console and so on. Please note that this port is not allowed to be connected with router.
Quick Installation Guide
1Power on
Plug the AC MiNi Router into an electrical outlet.
2Connect the AC MiNi Router
via Ethernet Cable
Disable the Wi-Fi on your computer. Connect the AC MiNi Router to your computer via an Ethernet cable.
via Wireless
Disconnect the Ethernet (wired) connec on to your computer. Click the Wi-Fi icon on the taskbar and connect to the AC MiNi Router's network (Wireless-AC_2G/5G).
Not connected
Connections are available
Wireless Network Connection
Wireless-AC_2G
Wireless-AC_5G
Connect automatically Connect
3Configure the AC MiNi Router
1.Open a web-browser and type http://mywifi.net in the address field. After a moment, a login window will appear. Select the language for the installation, and then enter admin for the Password, Then click the Submit button or press the Enter key to log in.
Language |
English |
Password |
|
Submit |
|
Language - Select the Language from the drop-down list. The default setting is English.
Password - Enter the password for Login. The default password is admin.
2.After successful log in, you can click the Wizard to quickly configure your router. Select the Operation Mode you need and click Next go on configuring.
Opera on Mode
Gate Way
Wireless AP Mode
Wireless Repeater Mode
WISP
Next
Gateway Mode(Default)
Stand Wireless Router Mode:This router connect to Internet by WAN port, and then other terminal devices can connect to this router by wireless connection or connect to this router’s LAN port by wired.
If GateWay is selected, Click drop-down menu of WAN Mode, and then WAN Connection Type will appear, Select the very type go on configuring.
|
|
|
b.If the connection type is Static IP Address, |
c.If the connection type is |
|||
|
|
|
the next screen will appear as shown below. |
PPPoE, the next screen will |
|||
|
|
|
Configure the following parameters and then |
appear as shown below. |
|||
|
|
|
click Next to continue. |
Configure the following |
|||
|
|
|
|
|
parameters and then click |
||
a.If the connection type is |
|
|
Next to continue. |
||||
Dynamic IP Address,Please |
|
|
|
|
|
||
click Next to continue. |
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
IP Address - This is the WAN IP address as seen by external users on the Internet (including your ISP). Enter the IP address into the field.
Subnet Mask - The Subnet Mask is used for the WAN IP address, it is usually 255.255.255.0.
Gateway - Enter the gateway IP address into the box if required.
Primary DNS - Enter the DNS Server IP address into the box if required.
Secondary DNS(option) - If your ISP provides another DNS server, enter it into this field.
PPPoE User Name - Enter the User Name provided by your ISP.
PPPoE Password - Enter the Password provided by your ISP.
SSID(2G)/SSID(5G)- Enter a value of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. The default SSID is set to be Wireless-AC_2G and Wireless-AC_5G.
Security - you can choose the security type on the drop-down list. The default setting is OPEN .
Security key - Wireless Password, When WPA/WPA2PSK is set as the Security
Type, You can enter ASCII characters between 8 and 63 characters or 8 to 64
Hexadecimal characters.
Enter SSID and Security, then click Apply to complete setup.
Note:Do not close this window,the window will automatically close when setup is complete.
Wireless AP Mode
Raditional wired router realize wireless function:This router can connect to uplink router’s LAN port by wired connection,user terminal can connect to this router by wireless connection.
If Wireless AP Mode is selected,The Wireless settings page will appear as shown below.
SSID(2G)/SSID(5G)- Enter a value of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. The default SSID is set to be Wireless-AC_2G and Wireless-AC_5G.
Security - you can choose the security type on the drop-down list. The default setting is OPEN .
Security key - Wireless Password, When WPA/WPA2PSK is set as the Security
Type, You can enter ASCII characters between 8 and 63 characters or 8 to 64
Hexadecimal characters.
Enter SSID and Security,then click Apply to complete setup.
Loading...