Pitco Frialator HERITAGE I12 User Manual

Heritage I12 Computer, Single Vat (PP11370) and Dual Vat (PP11372)

Quick Reference Card

HERITAGE I12 COMPUTER QUICK PROGRAMMING CARD

TURN ON and OFF

12 Product 12 Product

Keys Key Indicators

Thermometer ClockProgram

Key KeyKey

To Turn the Appliance ON : (See Note 1)

Press Rocker Switch to on. Display will show:[HEATING], [MELTING] or [READY].

To Turn the Appliance OFF :

(See Note 1) Press Rocker Switch

Off., Display will show: The Software number and then [OFF] [OFF] on single vat or a dual vat if both sides are off.

Note 1: Use Left Rocker Switch for left side and Right Rocker Switch for the right of dual vat control.

OPERATIONS

To Check Actual Temp : Press , Display shows actual temp and then returns to normal mode.

To Check Set Temp : Press

To Check Cook, Shake and Hold Time : Press then the Product Key desired. See example below:

Typical displays using key 4 as an example:

Key 4 set for 3 minutes and 28 seconds cook time.

Key 4 Shake Time is set for 2 minutes and :00 seconds before the end of the Cook.

, Display shows set temp and then returns to normal mode.

Key 4 Hold Time in set for 10:00 minutes.

In a few moments, the display will return to [READY] or last mode of operation.

To Check Time Remaining on a Non-Displayed Product Key when Multiple Timers are in Use :

Press then the Product Key of the Non – Displaying timer key, The display will switch from showing the lowest time remaining over to the time remaining for the key that was pressed. Repeat for other keys.

To Start a Cook : When display shows [READY] Press any [L,1,2,3,4,5,6,7,8,9,0,R] Product Key to start cook timer. The indicator light above will flash to indicate the timer is running:

To End a Cook : When the audible alarm is beeping, press the appropriate Product Key

(i.e. Key 4) with the

flashing indicator light, all other indicator lights are off until the key is pressed.

To Cancel a Cook : Press and Hold the Product Key you want to cancel until its indicator light is off.

Boil Out Mode : After filling empty vat with water, turn appliance on.

Automatic Entry : When the water temperature reaches just below 212oF (100oC) the

computer will display.

1 22

, press Product Key to continue heating,

display then shows .

Manual Entry : Press then enter Product Key [2] [1] [2] for Fahrenheit or [1] [0] [0]

0 0

for Celsius display unit. When last digit is entered, boil mode will start automatically. On Dual Vat computers both sides will enter boil mode. You must turn off both sides of the fryer to exit Boil mode.

L20-320 Rev 0 10/07

Heritage I12 Computer, Single Vat (PP11370) and Dual Vat (PP11372)

Func ti on K e y s P r o g r a m m i n g

Quick Reference Card

FIRST LEVEL PROGRAMMING

ENTER PROGRAM Press key, display show [PROGRAM], If PASSWORD IS REQUIRED, and you are unable

to remember the set password use (6684).

SET TEMPERATURE Single or Dual Vat (left side ) - Press Enter Desired Temperature.

Dual Vat (right side) - Press

To SAVE and CONTINUE Press , to EXIT First Level Programming Press Again.

SET TIME(s) .. Press , display shows [SELECT] [PRODUCT] ,Press any Product Key [L,1,2,3,4,5,6,7,8,9,0,R].

COOK TIME (CKn mm:ss] Enter Time and Press to proceed to SHAKE TIME (SHn mm:ss] Enter Time and

Press to proceed to HOLD TIME (HDn mm:ss] Enter Time and Press to proceed to HOLD PRE-ALARM

(PAn mm:ss] Enter Time and Press to return to [SELECT] [TIME] , repeat for other product keys.

To SAVE and CONTINUE Press , to EXIT First Level Programming Press Again.

Enter Desired Temperature.

SECOND LEVEL PROGRAMMING

ENTER PROGRAM Press key, display shows [PROGRAM], If PASSWORD IS REQUIRED, and you are

unable to remember the set password use (6684). Then press you have now entered the upper level programming, all the useable function keys will be lighted and the display will show [SELECT OPTIONS].

NOTE: Any time is used to save a setting, must be pressed to return to [SELECT OPTIONS].

FAHRENHEIT / CELCIUS – Toggle between Fahrenheit and Celcius scale by pressing the key

Change is saved by pressing the key to set

SET PASSWORD – Press to choose [PASS REQ] or [NO PASS]. If password is chosen then

press , current password displays. Use the number keys to enter new password and press to set.

BEEPER VOLUME & TONE – Press to toggle between levels 1,2,3 & Tone(1,2,3) and press to set.

LANGUAGE – Press to toggle between different languages and press to set.

MELT CYCLE – Press to toggle [NO MELT], [SOLID], or [LIQUID] and press to set.

RECOVERY TIME – Press to display [F065 LXXX], “F” is Factory time and lastest time is “LXXX”

CONTROL/TIMER (Single or Dual-left side) – Press to switch control to timer mode,press to set.

CONTROL/ TIMER (Dual Tank-right side) – Press to switch control to timer mode , press to set.

To SAVE and CONTINUE Press , to EXIT SECOND Level Programming Press Again.

OTHER DISPLAYS:

[PROBE OP] [OPEN] If probe is detected open, normal heating and cooking activities are suspended.

[HIGH TMP] [HIGH TMP] If vat temperature has exceeded set temperature by 40°F (22°C), or an absolute of 410°F (210°C) max. [DRAINING] [TURN OFF] Drain valve has been opened, Heat control is turned off. To restore to normal operation, close the drain

valve. Display will show [TURN OFF] [TURN OFF]. Turn controller off, and refill the vat. [HEAT] [FAILURE] OR [IGNITION] [FAILURE] Heating system failed to respond due to a tripped high temperature limit switch and

is in need of resetting. For gas models, the pilot failed to light, flame ignition detection is marginal or draft protector tripped on SCB. [SYSTEM] [FAILURE] If probe is detected as a short circuit, normal heating and cooking activities are suspended.

L20-320 Rev 0 10/07