Pioneer SIW-691, SIW-891 Service manual
IN-WALL SPEAKER
ORDER NO.
RRV4041
S-IW891
S-IW891
S-IW691
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Model Type Power Requirement Serial No. Remarks
S-IW891 XTWUM -------------- J
S-IW691 XTWUM -------------- J
The cabinet of the base model (S-IW891/XTW/UC, S-IW691/XTW/UC) of this product has been modified to
comply with the Airborne Toxic Control Measure, the environmental protection regulation of the state of
California.
The description on compliance with the regulation (Complies with CCR 93120.2[a] Phase 1) has been
added on the packaging of this product.
This service manual is intended for qualified service technicians; it is not meant for the casual
do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been
trained to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely,
you should not risk trying to do so and refer the repair to a qualified service technician.
/XTWUM
***
***
XXXXXX
XXXXXX
/XTWUM
**
**
WARNING
This product contains certain electrical parts contain chemicals which are known to the State of California to cause cancer,
birth defects or other reproductive harm.
Health & Safety Code Section 25249.6 - Proposition 65
PIONEER CORPORATION 1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2010
K-ZZZ JAN. 2010 Printerd in Japan
1
23
1. REASSEMBLY AND DISASSEMBLY PRECAUTIONS
• The grille is inserted into the baffle. To detach it, insert a grille
A
B
removal tool into each of the 4 corner holes of the grille net and
push up carefully.
• The Speaker frame is attached to the wall by 6 external screws.
To detach it, unfasten those screws.
• The LPF network is attached to the speaker frame by 2 external
screws. To detach it, first disconnect the cord to speaker.
Next remove the frame. Then unfasten those screws and
disconnect the cord to the HPF.
• The HPF network is attached to the CST chamber inside of
speaker frame by 5 screws.
To detach it, first detach CST and disconnect the cord to speaker
& LPF network. After removing the CST, disconnect the cords
to the speakers and the connector to the Level Control Assy.
After then, remove the baffle from the frame and disconnect the
cord to WF. And then, unfasten 5 screws tightened to the HPF
network.
Caution ; When re-attaching the HPF network, apply DIABOND
(black) (DB-1600WB) to the contact area to the
wooden bar and the through hole for cord again.
4
C
• The CST speaker is attached to the baffle by 4 external screws.
To detach it, unfasten those screws and then, disconnect the wire
connection. When reattaching it, face Mid terminal (bigger)
rightward.
• The woofers are attached to the baffle by 6 external screws.
To detach them, unfasten those screws and then, disconnect the
wire connection. When re-attaching them, face its terminal lower
right.
• Atta ch th e spe ake r fra me to the wall /ceiling, and
D
E
tighten the screws lightly (temporary attachment).
At this point the rotating clamp will rotate so that the rotating
clamp and frame are clamped on to the wall/ceiling.
Gently try pulling the speaker forward and check that all of the
rotating clamps have rotated outwards and are lightly clamping
to the wall/ceiling.
Speaker frame
Screw
Rotating clamp
• Tighten the screws firmly using no more than the
maximum torque specified.
F
Allowable maximum torque: 1.0 N.m
2
1234
S-IW891
5
67
2. EXPLODED VIEWS AND PARTS LIST
8
NOTES:
Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
The mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
2.1 PACKING
A
B
C
PACKING Parts List
Speaker
System
Mark No. Description Part No.
1 Carton Spacer SHB1188
NSP 2 1..Accessories Set (for Manual) SME3892
2..Polyethylene Bag S2 SHL1295
2..Operating Instruction SRD1385
(En/Frca)
NSP 2..Warranty Card SRY1048
3 1..Grille Ass'y SMG1912
NSP 2..Scrim SER1367
NSP 2..Punching Net SNC1213
4 Polyethylene Bag S7 (for Grille) SHL1393
5 Top Protector SHA2615
NSP 6 1..Accessories Set SME3856
(for Adhesive Tape)
2..Adhesive Tape SEH1134
2..Adhesive Tape SEH6026
2..Polyethylene Bag SHL1246
NSP 7 1..Accessories Set SME3858
(for Removal Tool)
2..Polyethylene Bag SHL1246
2..Grille Removal Tool SLH1096
8 Install Template SRK1036
9 Protection Sheet SHB1199
10 Paint Mask SHC1870
11 • • • • • • • •
12 Bottom Protector SHA2616
13 Polyethylene Bag SX SHL1479
14 Packing Case
(for S-IW891) SHG2858
(for S-IW691) SHG2857
NSP 15 Label Serial SRW1112
16 Caution Label SRN1017
D
E
F
S-IW891
5
6
7
8
3
Loading...