PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS SERVICE, INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
c
PIONEER CORPORATION 2001
T – ZZR JUNE 2001 Printed in Japan
Page 2
S-DV88SW
1. SAFETY INFORMATION
This service manual is intended for qualified service technicians ; it is not meant for the casual do-ityourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained
to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely, you
should not risk trying to do so and refer the repair to a qualified service technician.
WARNING
This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to cause
cancer, birth defects or other reproductive harm.
Health & Safety Code Section 25249.6 – Proposition 65
NOTICE
(FOR CANADIAN MODEL ONLY)
Fuse symbols (fast operating fuse) and/or (slow operating fuse) on PCB indicate that replacement parts must
be of identical designation.
REMARQUE
(POUR MODÈLE CANADIEN SEULEMENT)
Les symboles de fusible (fusible de type rapide) et/ou (fusible de type lent) sur CCI indiquent que les pièces
de remplacement doivent avoir la même désignation.
(FOR USA MODEL ONLY)
1. SAFETY PRECAUTIONS
The following check should be performed for the
continued protection of the customer and service
technician.
LEAKAGE CURRENT CHECK
Measure leakage current to a known earth ground (water
pipe, conduit, etc.) by connecting a leakage current tester
such as Simpson Model 229-2 or equivalent between the
earth ground and all exposed metal parts of the appliance
(input/output terminals, screwheads, metal overlays, control
shaft, etc.). Plug the AC line cord of the appliance directly
into a 120V AC 60Hz outlet and turn the AC power switch
on. Any current measured must not exceed 0.5mA.
Reading should
not be above
0.5mA
Earth
ground
Device
under
test
Also test with
plug reversed
(Using AC adapter
plug as required)
Test all
exposed metal
surfaces
Leakage
current
tester
ANY MEASUREMENTS NOT WITHIN THE LIMITS
OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL
SHOCK HAZARD AND MUST BE CORRECTED BEFORE
RETURNING THE APPLIANCE TO THE CUSTOMER.
2. PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in the appliance
have special safety related characteristics. These are
often not evident from visual inspection nor the protection
afforded by them necessarily can be obtained by using
replacement components rated for voltage, wattage, etc.
Replacement parts which have these special safety
characteristics are identified in this Service Manual.
Electrical components having such features are identified
by marking with a
in this Service Manual.
The use of a substitute replacement component which does
not have the same safety characteristics as the PIONEER
recommended replacement one, shown in the parts list in
this Service Manual, may create shock, fire, or other hazards.
Product Safety is continuously under review and new
instructions are issued from time to time. For the latest
information, always consult the current PIONEER Service
Manual. A subscription to, or additional copies of, PIONEER
Service Manual may be obtained at a nominal charge from
PIONEER.
on the schematics and on the parts list
AC Leakage Test
2
Page 3
LITHIUM BATTERY NOTICE
S-DV88SW
WARNING!
Lithium batteries. Danger of explosion. Replacement must be done by
qualified personnel and only by following the instructions given in the
service manual.
warning is stated on the product or in
This
the operating instructions. When replacing the
lithium batteries, follow the note below.
of
Dispose
away from children. Do not disassemble and
do not dispose of in fire.
battery used in this device may present a
The
fire or chemical hazard if mistreated. Do not
recharge, disassemble, heat above 100°C or
incinerate. Replace only with the same Part
Number. Use of another battery may present a
risk of fire or explosion.
Note: The
sition is shown in the exploded views.
the used battery promptly. Keep
lithium battery installation po-
ADVARSEL!
Lithiumbatteri − Eksplosionsfare ved
fejlagtig håndtering. Udskiftning må
kun ske med batteri af samme fabrikat
og type. Levér det brugte batteri tilbage
til leverandøren.
Denne advarsel or angivet på produktet
eller i brugsvejledningen. Ved udskiftning
af lithium batterierne følges nedenstående
anveisning.
Batterierne
er af samme type og mærke.
må
kun udskiftes med batteri-
3
Page 4
S-DV88SW
2. EXPLODED VIEWS AND PARTS LIST
NOTES:• Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
2.1 PACKING
The mark found on some component parts indicates the importance of the safety factor of the part.
•
Therefore, when replacing, be sure to use parts of identical designation.
Screws adjacent to mark on the product are used for disassembly.
•
21
33
19
MYXJI Only
6
NVXJI Only
7
8
9
10
11
12
13
6
7
16
18
3
23
22
20
24
25
26
30
5
1
29
31
15
17
14
32
4(1/2)
27
28
4(2/2)
2
4
Page 5
(1) PACKING PARTS LIST
S-DV88SW
Mark No. Description Part No.
1Poly Bag S6SHL1292
2Packig Case
3Protector (Top)SHA2313
4Protector (Bottom)SHA2314
5ProtectorSHB1097
6Operating InstructionsARE7276
(English/French)
7Operating InstructionsARE7280
(Setting up : English/French)
8Operating Instructions
(Dutch/Spanish)
9Operating Instructions
(Setting up : Dutch/Spanish)
10Operating Instructions
(German/Italian)
11Operating Instructions
(Setting up : German/Italian)
12Operating Instructions
(Portuguese/Swedish)
13Operating Instructions
(Setting up : Portuguese/Swedish)
14FM AntennaADH7005
15AM Loop AntennaATB7009
16Remote ControlAXD7305
NSP 17Lithium Battery (CR2025)VEM1011
18Polyethylene Bag S3SHL1293
19Battery Cover103RRC14701R
20AC Power Cord
S-DV88SW/MYXJI and S-DV88SW/NVXJI are constructed the same except for the following:
Mark
No.
NSP17AMPLIFIER ASSYAXX7106AXX7102 Refer to 2.3 section.
NSP19Serial LabelSME3155SME3205
Symbol and Description
S-DV88SW S-DV88SW
/MYXJI
( DVD AMP : AWM7625)
Part No.
Remarks
/NVXJI
7
Page 8
S-DV88SW
2.3 AMPLIFIER ASSY
23
14
23
10
11
7
A
9
B
17
24
26
23
2
24
12
26
6
23
23
23
23
9
23
24
D
E
3
C
8
21
22
20
23
27
15
23
19
16
18
13
1
A
5
25
A
26
4
8
Page 9
(1) AMPLIFIER ASSY PARTS LIST
Mark No. Description Part No.
1 AF ASSYAWU7829
2 AMP ASSYAWU7827
3 PRI ASSYAWU7824
4 Wood BaseAMM7006
NSP5 ChassisANA7109
6 Power TransformerATS7307
NSP7 Harness LifterAEC7296
8 Wire SaddleAEC7297
9 Heat Sink HolderANG7317
NSP10 Heat SinkANH7130
11 Mica SeatAEE7034
12 IC HolderANG7318
13 Fuse (T3.15A)REK1027
14 TRADE ASSYAWU7828
NSP15 Seriall LabelRRW-168
16 SP LabelAAX7872
17 REG ASSYAWU7826
18 Rear PanelSee Contrast table(2)
19 DC Fan MotorAXM7014
20 Fan CoverAEC7280
S-DV88SW
NSP22 PCB HolderAEC7057
21 Nylon RivetAEC7318
23 ScrewBBZ30P080FMC
24 ScrewBBZ30P140FMC
25 ScrewBBZ30P300FZK
26 ScrewBYC40P140FMC
27 ScrewPSC30P080FNI
(2) CONTRAST TABLE
S-DV88SW /MYXJI and /NVXJI are constructed the same except for the following:
Part No.
Mark
No.
18Rear PanelANC8028ANC8024
Symbol and Description
S-DV88SWS-DV88SW
/MYXJI
/NVXJI
Remarks
9
Page 10
1
A
F
R
A
23
S-DV88SW
3. BLOCKDIAGRAM AND SCHEMATIC DIAGRAM
3.1 BLOCK DIAGRAM AND OVERALL CONNECTION DIAGRAM
A
4
To SIDEL ASSY
CN3703
CN3702
GNDALR
V+B
4
1A
18
13
7,9,10,13
8,15
15
GNDALR
V+B
V–B
V+B
819
91
V–B
6
2
15
7
IC3321
RY3661
RLC1
IC3601
TDA7294V
B
RY3461
RLC2
RY3461
RLC2
RY3361
RY3561
6
IC3401
Peripheral
Circuit
RLC1
C
RY3361
RLC1
FAN DET.
Circuit
GNDF
V+12R
V+12R
FDET
V–12R
Relay Cont.
Circuit
GNDF
AC
RLC2
RYFS
GNDB
RLC2
7
RYFR
XMUTE
14
IC3621
STK402-240
RLC1
1
1110
8
IC3301
10
11
STK402-040
9
V–B
15
Peripheral
Circuit
XMUTE
RYFS
RYRC
SWMUTE
V+12R
V+5A
FDET
AC
V–12R
1
13
1A
V+B
SWMUTE
GND FAN
V–B
AKM7067
IC3151
7
1
IC3161
7
1
IC3171
1
7
5
3
V+5A
FL
31
32
33
34
35
36
37
38
39
40
41
42
IC3001
E-VOL
IC
M62446FP
Q3092
Q3091
FL
17
16
C
11
SL
9
8
S
SW
6
3
2
1
5
FR
C
3
SL
SR
SW
3
V+5D
5
V–12R
AMP ASSY ( AWU7827 )
B
Q61/D61
+5V
Reg.
V+12A
V+12R
IC51
+12V
Reg.
NJM7812FA
IC52
–12V
Reg.
D31
S1WB(
D
V+5A
V+5D
NJM7912FA
V–12A
10
V–12R
1234
Page 11
EL ASSY
R
5
678
Note : When ordering service parts, be sure to refer to "EXPLODED VIEWS
and PAR TS LIST" or "PCB PARTS LIST".
S-DV88SW
To MOTHER ASSY
XV-DV77
A
CN3704
RY51
+
3
1
2
IC3001
FL
31
32
33
34
35
36
37
38
39
40
41
42
E-VOL
IC
M62446FP
R
L
V+5A
R
Q3092
Q3091
17
16
11
9
8
6
3
2
1
–
5
+
7
FL
C
SL
SW
6
–
FR
IC3004
3
+
1
2
–
5
SR
+
6
7
–
IC3005
3
+
1
2
–
5
+
7
6
–
IC3006
CN3705
POWER ON/OFF
CN51
PRI ASSY (AWU7824)
C
B
D51
S1WB(A)60SD
2A
2R
IC51
+12V
Reg.
NJM7812FA
IC52
–12V
Reg.
NJM7912FA
2A
2R
D31
D41
D3SBA20
D3SBA20
D11
IC11
10A
IC12
10A
IC31
S1WB(A)60SD
IC32
AF ASSY ( AWU7829 )
5
IC41
3.0A
5A
IC71
3.0A
A
REG ASSY
D
(AWU7826)
C
TRADE ASSY
E
(AWU7828)
ATS7307
7A
Not used
D
11
6
7
8
Page 12
1
F
S-DV88SW
3.2 AF ASSY(1/2)
23
4
A
To SIDEL ASSY
B
A
AF ASSY(AWU7829)
1/2
(FL)(
(FL)
(SL)
(C)
(SL)
SW
C
D
(C)
SW
12
1/2
A
1234
Page 13
5
678
S-DV88SW
: Audio Signal Route
(FL)
(FL)
(SL)
(FL)
A
(FL)
SW
(SL)
CN3301
B
(SL)
(C)
(C)
B
(C)
SW
SW
CN51
C
C
2/2
A
D
: The power supply is shown with the marked box.
2/2
A
1/2
A
5
6
7
8
13
Page 14
1
23
S-DV88SW
3.3 AF(2/2), REG and TRADE ASSYS
4
A
B
A
AF ASSY (AWU7829)
2/2
C
D
14
1/2
A
1234
DE
REG ASSY
D
(AWU7826)
TRADE ASSY
E
(AWU7828)
Page 15
5
678
S-DV88SW
A
CN3302
B
1/2
A
B
XV-DV77(CN8001)
C
1/2
A
1/2
A
D
2/2
A
5
6
7
8
15
Page 16
1
S-DV88SW
3.4 AMP ASSY
B
23
AMP ASSY(AWU7827)
4
A
B
A
1/2
CN3702CN3052
Front Power Amp
(FL)
(FL)
SW
Rear and Center
Power Amp
(SL)
(C)
(FL)
(SL)
A
(C)
2/2
C
SW Power Amp
D
: Audio Signal Route
16
B
1234
Page 17
5
(FL)(FL)
678
S-DV88SW
A
(SL)
(C)
SW
SW
(SL)
To Satellite Speaker
(C)
B
C
To Subwoofer
To FAN
D
B
5
6
7
8
17
Page 18
S-DV88SW
3.5 PRI ASSY
A
1
A
2/2
CN12
23
PRI ASSY (AWU7824)
C
4
Other model Use
B
A
2/2
This model Use
CN11
C
A
1/2
CN3705
D
18
C
1234
Page 19
5
• NOTE FOR FUSE REPLACEMENT
CAUTION -
C
FOR CONTINUED PROTECTION AGAINST RISK OF FIRE.
REPLACE WITH SAME TYPE AND RATINGS ONLY.
PRI ASSY (AWU7824)
678
S-DV88SW
A
B
REK1027
(T3.15AL250v)
AC POWER CORD
MYXJI : ADG1154
NVXJI : ADG1156
5
6
7
8
C
19
C
D
Page 20
1
23
S-DV88SW
4. PCB CONNECTION DIAGRAM
4.1 AF ASSY
A
NOTE FOR PCB DIAGRAMS :
1. Part numbers in PCB diagrams match those
in the schematic diagrams.
2. A comparison between the main parts of PCB
and schematic diagrams is shown below.
Symbol In PCB
Diagrams
BCE
BCE
D
B
3. The parts mounted on this PCB include all
necessary parts for several destinations.
For further information for respective destinations,
be sure to check with the schematic diagram.
4. View point of PCB diagrams.
Connector
Symbol In Schematic
Diagrams
BCEBCE
BCE
BCE
DGS
DGGSS
Capacitor
Part Name
Transistor
Transistor
with resistor
Field effect
transistor
Resistor array
3-terminal
regulator
AF ASSY
A
To Power Transformer
4
B
CN3302
C
D
P.C.Board
Chip Part
SIDE A
SIDE B
Q61
IC32
IC41
IC11
IC12
E
CN44
20
A
1234
Page 21
5
678
S-DV88SW
A
302
B
CN3301
SIDE A
To
XV-DV77
SIDEL ASSY
CN5081
B
CN44
C
(ANP7408-A)
IC3831
To XV-DV77
MOTHER ASSY
CN8001
D
A
5
6
7
8
21
Page 22
S-DV88SW
A
B
1
AF ASSY
A
23
4
C
IC3004
D
22
A
1234
Q93
IC3005
IC300
Q92
Q95
Q94
Q96
Q97
IC3009
Q91IC3093
IC3001
IC3002
IC3008
IC3003
IC3007
Page 23
5
678
S-DV88SW
A
SIDE B
B
IC3003
IC3007
IC3091
IC3092
5
IC3775
IC12
C
(ANP7408-A)
IC41
6
IC32
Q32
Q61
D
A
7
8
23
Page 24
1
S-DV88SW
4.2 AMP ASSY
23
4
AMP ASSY
B
A
A
CN3052
B
SIDE A
Q3772
IC3301
IC3321
IC3621
Q3714
IC3601
Q3713
A
CN3702
C
IC3401
Q3702
Q3651
Q3701
To FAN
D
(ANP7048-A)
24
To Satellite Speaker
B
1234
To Satellite Speaker
To Subwoofer
Page 25
1
234
S-DV88SW
SIDE B
A
Q3772 Q3774
Q3771
Q3301
IC3301
Q3302
Q3717
Q3716
Q3712
Q3714
B
Q3711
Q3713
IC3601
Q3705
Q3704
Q3701
Q3042
Q3651
Q3451
Q3551
Q3703
Q3706
Q3702
Q3351
Q3352
Q3701
IC3401
Q3041
C
Q3501
D
(ANP7048-A)
B
1
2
3
4
25
Page 26
S-DV88SW
4.3 PRI, REG and TRADE ASSYS
A
B
1
PRI ASSY
C
23
4
SIDE A
C
A
CN3705
(ANP7048-A)
To Power Transformer T1
IC361
D
26
C
1234
Page 27
1
REG ASSY
D
234
S-DV88SW
A
SIDE BSIDE A
B
TRADE ASSY
E
Q41Q43Q43
A
CN41
Q44
(ANP7048-A)
Q42Q41
C
(ANP7048-A)
D
D
1
2
3
E
4
27
Page 28
S-DV88SW
Mark No. Description Part No.
Mark No. Description Part No.
5. PCB PARTS LIST
NOTES:•Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
The mark found on some component parts indicates the importance of the safety factor of the part.
•
Therefore, when replacing, be sure to use parts of identical designation.
When ordering resistors, first convert resistance values into code form as shown in the following examples.
•
Ex.1 When there are 2 effective digits (any digit apart from 0), such as 560 ohm and 47k ohm (tolerance is shown by J=5%,
and K=10%).
1) The Amplifier Assy is attached to the cabinet by 6 external
screws 1. To detach it, pull down the subwoofer toward the
left side.
2) Then unfasten those screws 1 .
3) Then stand up the speaker again. To detach the Amplifier Assy,
first remove the connecting code. Then pull straight the Amplifier
Assy toward back and remove it.
2. Removing the Subwoofer
1) The speaker element is attached to the back board by 4 external
screws 2.To detach it, unfasten those screws.
2) When attaching it,face its terminal downward.
S-DV88SW
Screw1
Screw1
3. Removing the Cosmetic duct
1) The cosmetic duct is attached to the baffle by press-fitting.
To detach it,pry it open by inserting a flat blade screwdriver
into lower side.