The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
1)
Read these instructions.
2)
Keep these instructions.
3)
Heed all warnings.
4)
Follow all instructions.
5)
Do not use this apparatus near water.
6)
Clean only with dry cloth.
7)
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8)
Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9)
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10)
Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
CAUTION:
TO PREVENT THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
11)
Only use attachments/accessories specified by the
manufacturer.
12)
Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
13)
Unplug this apparatus during lightning storms or
when unused for long periods of time.
14)
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
D3-4-2-1-1_En-A
WARNING: This equipment is not waterproof.
To prevent a fire or shock hazard, do not place any
container filed with liquid near this equipment
(such as a vase or flower pot) or expose it to
dripping, splashing, rain or moisture.
D3-4-2-1-3_A_En
NOTE TO CATV SYSTEM INSTALLER
THIS REMINDER IS PROVIDED TO CALL THE CATV
SYSTEM INSTALLER’S ATTENTION TO ARTICLE
820-40 OF THE NEC THAT PROVIDES GUIDELINES
FOR PROPER GROUNDING AND, IN PARTICULAR,
SPECIFIES THAT THE CABLE GROUND SHALL BE
CONNECTED TO THE GROUNDING SYSTEM OF
THE BUILDING, AS CLOSE TO THE POINT OF
CABLE ENTRY AS PRACTICAL.
D1-4-2-8_En
WARNING: This product equipped with a three-
wire grounding (earthed) plug - a plug that has a third
(grounding) pin. This plug only fits a grounding-type
power outlet. If you are unable to insert the plug into an
outlet, contact a licensed electrician to replace the
outlet with a properly grounded one. Do not defeat the
safety purpose of the grounding plug
D3-4-2-1-6_A_En
WARNING: To prevent a fire hazard, do not place
any naked flame sources (such as a lighted candle) on
the equipment.
D3-4-2-1-7a_A_En
This digital television is capable of receiving analog
basic, digital basic and digital premium cable
television programming by direct connection to a cable
system providing such programming. A security card
provided by your cable operator is required to view
encrypted digital programming. Certain advanced and
interactive digital cable services such as video-ondemand, a cable operator’s enhanced program guide
and data-enhanced television services may require the
use of a set-top box. For more information call your
local cable operator.
VENTILATION CAUTION:
When installing this unit, make sure to leave space
around the unit for ventilation to improve heat
radiation. For the minimum space required, see page
16.
WARNING: Slots and openings in the cabinet are
provided for ventilation to ensure reliable operation of
the product, and to protect it from overheating. To
prevent fire hazard, the openings should never be
blocked or covered with items (such as newspapers,
table-cloths, curtains) or by operating the equipment
on thick carpet or a bed.
WARNING: Handling the cord on this product or
cords associated with accessories sold with the
product will expose you to chemicals listed on
proposition 65 known to the State of California and
other governmental entities to cause cancer and birth
defect or other reproductive harm.
Wash hands after handling.
D36-P4_A_En
FEDERAL COMMUNICATIONS
COMMISSION DECLARATION OF
CONFORMITY
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
Information to User
Alteration or modifications carried out without
appropriate authorization may invalidate the user’s
right to operate the equipment.
operation.
Product Name: Plasma Display System
Model Number: PRO-1150HD/PRO-950HD
Product Category: Class B Personal Computers &
Peripherals
[For Canadian model]
This Class B digital apparatus complies with Canadian
ICES-003.
Responsible Party Name: PIONEER ELECTRONICS
SERVICE, INC.
Address: 1925 E. DOMINGUEZ ST., LONG BEACH, CA
90801-1760, U.S.A.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
D8-10-1-2_En
CAUTION: This product satisfies FCC regulations when shielded cables and connectors are used to connect the
unit to other equipment. To prevent electromagnetic interference with electric appliances such as radios and
televisions, use shielded cables and connectors for connections.
D8-10-3a_En
IMPORTANT NOTICE – THE SERIAL NUMBER FOR THIS EQUIPMENT IS LOCATED IN THE REAR.
PLEASE WRITE THIS SERIAL NUMBER ON YOUR ENCLOSED WARRANTY CARD AND
KEEP IN A SECURE AREA. THIS IS FOR YOUR SECURITY.
CAUTION:
disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power. Therefore, make sure the unit has been
installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord
should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation)
The switch on this unit will not completely shut off all power from the AC outlet. Since the power cord serves as the main
D1-4-2-6-1_En
D3-4-2-2-2a_A_En
STANDBY:When placed into the standby mode, the main power flow is cut and the unit is no longer
fully operational.
STANDBY/ON Indicator: The indicator is lit red when the unit is in the standby mode and lit blue when it is in the
power-on mode. No operation can be performed when the indicator is off. However, the
Plasma Display system will still consume some power as long as the power cord is
inserted into the power outlet.
Operating Environment
Operating environment temperature and humidity:
+0 ˚C to +40 ˚C (+32 ˚F to +104 ˚F); less than 85 %RH (cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light)
D3-4-2-1-7c_A_En
Contents
Thank you for buying this Pioneer product.
Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading
the instructions, put them away in a safe place for future reference.
In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown in the explanatory
drawings. However the method of connecting and operating the unit is the same.
Illustrations shown in this manual are for the PRO-1150HD unless otherwise specified.
Contents
01 Important User Guidance
Information ........................................... 7
In order to obtain maximum enjoyment from this Pioneer PRO1150HD/PRO-950HD plasma display, please first read this
information carefully.
With the Pioneer PRO-1150HD/PRO-950HD, you can be assured
of a high quality plasma display with long-life and high reliability.
To achieve images of exceptional quality, this Pioneer plasma
display incorporates state-of-the-art design and construction, as
well as very precise and highly advanced technology.
The Pioneer PRO-1150HD/PRO-950HD incorporates the latest in
color filter technology – Direct Color Filter. This improves the
color / picture reproduction of these models as compared to
previous models. It also eliminates the need for a physical glass
panel to be placed in front of the plasma panel, which furthers
Pioneer’s continued goal of reducing environmental waste in
consumer electronics, now during the manufacturing process
and in the future during the recycling process.
Over the course of its lifetime, the luminosity of the Pioneer PRO1150HD/PRO-950HD plasma display will diminish very slowly,
such as with all phosphor-based screens (for example, a
traditional tube-type television). To enjoy beautiful and bright
images on your Pioneer plasma display for many years to come,
please carefully read and follow the usage guidelines below.
Usage guidelines
All phosphor-based screens (including conventional tube-type
televisions) can be affected by displaying static images for a
prolonged period. Plasma displays are no exception to this rule.
After-image and permanent effects on the screen can be avoided
by taking some basic precautions. By following the
recommendations listed below, you can ensure longer and
satisfactory results from your plasma:
• Whenever possible, avoid frequently displaying the same
image or virtually still moving pictures (e.g. closed-captioned
images or video game images which have static portions).
• Avoid viewing the On Screen Display for extended periods,
from a DVD player, VCR, and all other components.
• Do not leave the same picture freeze-framed or paused
continuously over a long period of time, when using the still
picture mode from a TV, VCR, DVD player or any other
component.
• Images which have both very bright areas and very dark areas
side by side should not be displayed for a prolonged period of
time.
• When playing a game, the “GAME” mode setting within “AV
Selection” is strongly recommended. However, please limit its
use to less than two hours at a time.
• After playing a game, or displaying a PC image or any still
image, it is best to view a normal moving picture in the “WIDE”
or “FULL” screen setting for over three times longer than the
previous still/moving image.
• After using the plasma display, always switch the display to
“STANDBY” mode.
• Extensive viewing of content with top, bottom, or side masks
may cause uneven wear. After viewing masked content, it is
recommended to view full screen motion video for an equal or
greater amount of time.
Installation guidelines
The Pioneer PRO-1150HD/PRO-950HD plasma display
incorporates a very thin design. To ensure safety, please take the
proper measures to mount or install the plasma display, in order
to prevent the unit from tipping over in the event of vibration or
accidental movement.
This product should be installed by using only parts and
accessories designed by Pioneer. Use of accessories other than
the Pioneer stand or installation bracket may result in instability,
and could cause injury. For custom installation, please consult
the dealer where the unit was purchased. To ensure correct
installation, experienced and qualified experts must install the
unit.
Pioneer will not be held responsible for accident or damage
caused by the use of parts and accessories manufactured by
other companies, inadequate installation or stabilization,
erroneous operation, remodeling or natural disasters.
To avoid malfunction and overheating when installing, make sure
that the vents on the main unit are not blocked. To ensure proper
heat emission:
• Distance the unit slightly from other equipment, walls, etc. For
the minimum space required around the unit, see page 16.
• Do not fit the unit inside narrow spaces where ventilation is
poor.
• Do not cover with a cloth, etc.
• Clean the vents on the sides and rear of the unit to remove dust
build-up by using a vacuum cleaner set to its lowest suction
setting.
• Do not place the product on a carpet or blanket.
• Do not leave the product tilted over.
• Do not invert the product.
Using the unit without proper ventilation may cause the internal
temperature to rise, and could result in possible malfunction.
When the surrounding or internal temperature exceeds a certain
degree, the display will automatically power off in order to cool
the internal electronics and prevent a hazardous occurrence.
Malfunction can be caused by many factors: inappropriate
installation site, improper assembly/installation/mounting,
improper operation of or modifications made to this product.
However, Pioneer cannot be held responsible for accidents or
malfunction caused by the above.
Note
The following are typical effects and characteristics of a
phosphor-based matrix display and as such, are not covered by
the manufacturer’s limited warranties:
• Permanent residual images upon the phosphors of the panel.
• The existence of a minute number of inactive light cells.
• Panel generated sounds, examples: Fan motor noise, and
electrical circuit humming / glass panel buzzing
En
7
01
Important User Guidance Information
Caution
Pioneer bears no responsibility for any damage arising from
incorrect use of the product by you or other people, malfunctions
when in use, other product related problems, and use of the
product except in cases where the company must be liable.
Plasma display protection function
When still images (such as photos and computer images) stay on
the screen for an extended period of time, the screen will be
slightly dimmed. This is because the protection function of the
plasma display automatically adjusts the brightness to protect
the screen when detecting still images; so this does not
designate malfunction. The screen is dimmed when a still image
is detected for about three minutes.
Information of pixel defect
Plasma screens display information using pixels. Pioneer plasma
display panels contain a very large number of pixels. (Depending
on the panel size; over 2.3 million pixels in case of a 42 inch
display, over 3.1 million pixels in case of a 50 inch display). All
Pioneer display panels are manufactured using a very high level
of ultra-precision technology and undergo individual quality
control.
In rare cases, some pixels can be permanently switched off, or
on, resulting in either a black or colored pixel permanently fixed
on the screen.
This effect is common to all plasma displays because it is a
consequence of the technology.
If the defective pixels are visible at a normal viewing distance of
between 2.5 and 3.5 meters (8.2 and 11.5 feet) while viewing a
normal broadcast (i.e. not a test card, still image or single color
display) please contact Pioneer Customer Support Div. (USA) or
Customer Satisfaction Dept. (CANADA). See back cover.
If, however, they can only be seen close up or during single color
displays then this is considered normal for this technology.
Infrared rays
The plasma display releases infrared rays because of its
characteristics. Depending on how the plasma display is in use,
the remote controls of nearby equipment may be adversely
affected or wireless headphones using infrared rays are
interfered with by noise. If this is the case, place that equipment
at a location where its remote control sensor is not affected.
Radio interference
While this product meets the required specifications, it emits a
small amount of noise. If you place such equipment as an AM
radio, personal computer, and VCR close to this product, that
equipment may be interfered. If this happens, place that
equipment far enough from this product.
Plasma display driving sound
The screen of the plasma display is composed of extremely fine
pixels and these pixels emit light according to received video
signals. This principle may cause you to hear a buzz or electrical
hum coming from the plasma display.
Do not attach such items as labels and tape to the
product.
• This may result in the discoloration or scratch of the cabinet.
When not using the product for a long period of time
• If you do not use the product for a long period of time, the
functions of the product may be adversely affected. Switch on
and run the product occasionally.
Condensation
• Condensation may take place on the surface or inside of the
product when the product is rapidly moved from a cold place
to a warm place or just after a heater i s switched o n on a winter
morning, for example. When condensation takes place, do not
switch on the product until condensation disappears. Using
the product with condensation may result in malfunction.
Cleaning the surface of the screen and the glossy
surface of the front cabinet
• When cleaning the surface of the screen or the glossy surface
of the front cabinet, gently wipe it with a dry soft cloth; the
supplied cleaning cloth or other similar cloths (e.g., cotton and
flannel). If you use a dusty or hard cloth or if you rub the screen
hard, the surface of the product will be scratched.
• If you clean the surface of the screen with a wet cloth, water
droplets on the surface may enter into the product, resulting in
malfunction.
Cleaning the cabinet
• When cleaning the cabinet of this product, gently wipe it with
a clean soft cloth (e.g., cotton and flannel). If you use a dusty or
hard cloth or if you rub the cabinet hard, the surface of the
cabinet will be scratched.
• The cabinet of this product is mostly composed of plastic. Do
not use chemicals such as benzene or thinner to clean the
cabinet. Using these chemicals may result in quality
deterioration or coating removal.
• Do not expose the product to volatile gas or fluid such as
pesticide. Do not bring the product in contact with rubber or
vinyl products for a long period of time. The effect of plasticizer
in the plastic may result in quality deterioration or coating
removal.
• If you clean the surface of the cabinet with a wet cloth, water
droplets on the surface may enter into the product, resulting in
malfunction.
Handles at the rear of the plasma display
• Do not remove the handles from the rear of the plasma display.
• When moving the plasma display, ask another person for help
and use the handles attached to the rear of the plasma display.
Do not move the plasma display by holding only a single
handle. Use the handles as shown on page 16.
• Do not use the handles to hang the product when installing or
carrying the product, for example. Do not use the handles for
the purpose of preventing the product from tilting over.
8
En
Important User Guidance Information
01
Fan motor noise
The rotation speed of the cooling fan motor increases when the
ambient temperature of the plasma display becomes high. You
may hear the sound of the fan motor at that time.
To use this product for a long period of time
• Energy Save maintains efficiency of the screen for a long
period of time by decreasing picture brightness and lowering
power consumption. Setting Energy Save to “Mode 1” is
recommended for increased efficiency.
About the menu window size following video format
switch
The video program that you watch may be high definition (HD) or
standard definition (SD). This plasma display is designed to scale
to each type of definition properly. If the video program’s
definition type changes while a menu window is displayed on the
screen (for example: HD → SD or SD → HD), the menu size may
temporarily shrink or enlarge until the scaling is completed. This
may happen, for example, when you switch between television
and an external digital video recorder
(D-VHS), or when your recorded program switches between
different definition types, while the on-screen menu is being
shown.
If this happens, the menu will return to its normal size after two
to three seconds. This action is normal, and does not indicate a
problem with your plasma display.
Image Retention
When a static image is left frozen on a display for several hours,
a faint imprint of the image, known as image retention, can
remain. This image retention may be temporary or permanent.
Although caused by different things, image retention can occur
on all display technologies, including plasma and LCD. On
today’s plasma displays, permanent image retention is less of a
worry. Most image retention can be improved simply by watching
moving video.
Image retention, also known as burn-in, can occur in all
phosphor-based display systems (including CRT television
systems–both direct view and projection–as well as plasma
displays). Displaying the same still images for long periods
should be avoided as permanent image retention or burn-in may
occur. Recommended guidelines are as follows:
Do not display static images for long periods (such as still
images, fixed images from PC or TV game equipment, and/or
fixed images such as time of day indicator or channel logo
display).
Do not display content in the 4:3 aspect ratio (black or gray bars
on left and right side of content) or letter-box content (black bars
above and below content) for extended periods of time, or use
either of these viewing modes repeatedly within a short period of
time. This plasma display is equipped with multiple wide-screen
viewing modes; use one of these screen modes to fill the entire
screen with content.
Displaying dark images after displaying still images for a period
of time may cause image retention. In most cases, the image
retention can be corrected by displaying bright images for a
similar period of time.
If you display still images on your plasma display for long periods
of time, image retention may be irreparable.
Caution
Panel sticking and after-image lag
• Displaying the same images such as still images for a long
time may cause after-image lagging. This may occur in the
following two cases.
1After-image lagging due to remaining electric load
When image patterns with very high peak luminance are
displayed more than one minute, after-image lagging may occur
due to the remaining electric load. The after-images remaining
on the screen will disappear when moving images are displayed.
The time for the after-images to disappear depends on the
luminance of the still images and the time they had been
displayed.
2After-image (lag image) due to burning
Avoid displaying the same image on the plasma display
continuously over a long period of time. If the same image is
displayed continuously for several hours, or for shorter periods of
time over several days, a permanent after-image may remain on
the screen due to burning of the fluorescent materials. Such
images may become less noticeable if moving images are later
displayed, but they will not disappear completely.
Note
• When a program menu, TV Guide screen or frozen image is
displayed for 5 to 10 minutes, the system automatically turns
the image off to prevent damage from screen burning.
• To minimize image retention, the display position is
automatically changed imperceptibly when watching plasma
display.
Some parts of the picture may not be visible (see Orbiter on
page 64).
Minimizing damage from screen burning
• Set the Side Mask detection function to “On”. The High
Definition 16:9 aspect ratio images containing side masks will
be detected automatically and side masks will be added or the
image displayed in full screen.
• We recommend that you enjoy watching images displayed in full
screen, except when doing so may result in copyright
infringement. The use of images displayed in screen sizes
different from the original video for financial gain or in
broadcasting for public viewing may result in infringement of the
legally enforceable rights of the copyright holder (see page 62).
Caution
DO NOT PLACE THIS PRODUCT ON AN UNSTABLE CART,
STAND, TRIPOD, BRACKET, OR TABLE. THE PRODUCT MAY
FALL, CAUSING SERIOUS PERSONAL INJURY AND SERIOUS
DAMAGE TO THE PRODUCT. USE ONLY WITH A CART, STAND,
TRIPOD, BRACKET, OR TABLE RECOMMENDED BY THE
MANUFACTURER, OR SOLD WITH THE PRODUCT. FOLLOW
THE MANUFACTURER’S INSTRUCTIONS WHEN INSTALLING
THE PRODUCT AND USE MOUNTING ACCESSORIES
RECOMMENDED BY THE MANUFACTURER.
A PRODUCT AND CART COMBINATION SHOULD BE MOVED
WITH THE CARE. QUICK STOPS, EXCESSIVE FORCE, AND
UNEVEN SURFACES MAY CAUSE THE PRODUCT AND CART
COMBINATION TO OVERTURN.
En
9
02
Safety Precautions
Chapter 2
Safety Precautions
Electricity is used to perform many useful functions, but it can
also cause personal injuries and property damage if improperly
handled. This product has been engineered and manufactured
with the highest priority on safety. However, improper use can
result in electric shock and/or fire. In order to prevent potential
danger, please observe the following instructions when
installing, operating and cleaning the product. To ensure your
safety and prolong the service life of your product, please read
the following precautions carefully before using the product.
1. Read instructions—All operating instructions must be read
and understood before the product is operated.
2. Keep this manual in a safe place—These safety and operating
instructions must be kept in a safe place for future reference.
3. Observe warnings—All warnings on the product and in the
instructions must be observed closely.
4. Follow instructions—All operating instructions must be
followed.
5. Cleaning—Unplug the power cord from the AC outlet before
cleaning the product. To clean the product, use the supplied
cleaning cloth or other soft cloth (e.g., cotton, flannel). Do not
use liquid cleaners or aerosol cleaners.
6. Attachments—Do not use attachments not recommended by
the manufacturer. Use of inadequate attachments can result
in accidents.
7. Water and moisture—Do not use the product near water,
such as bathtub, washbasin, kitchen sink and laundry tub,
swimming pool and in a wet basement.
8. Stand—Do not place the product on an unstable cart, stand,
tripod or table. Placing the product on an unstable base can
cause the product to fall, resulting in serious personal
injuries as well as damage to the product. Use only a cart,
stand, tripod, bracket or table recommended by the
manufacturer or sold with the product. When mounting the
product on a wall, be sure to follow the manufacturer’s
instructions. Use only the mounting hardware recommended
by the manufacturer.
9. When relocating the product placed on a cart, it must be
moved with utmost care. Sudden stops, excessive force and
uneven floor surface can cause the product to fall from the
cart.
10. Ventilation—The vents and other openings in the cabinet are
designed for ventilation. Do not cover or block these vents
and openings since insufficient ventilation can cause
overheating and/or shorten the life of the product. Do not
place the product on a bed, sofa, rug or other similar surface,
since they can block ventilation openings. This product is not
designed for built-in installation; do not place the product in
an enclosed place such as a bookcase or rack, unless proper
ventilation is provided or the manufacturer’s instructions are
followed.
11. Power source—This product must operate on a power source
specified on the specification label. If you are not sure of the
type of power supply used in your home, consult your dealer
or local power company.
10
En
12. Power cord protection—The power cords must be routed
properly to prevent people from stepping on them or objects
from resting on them. Check the cords at the plugs and
product.
13. The plasma display used in this product is made of glass.
Therefore, it can break when the product is dropped or
applied with impact. Be careful not to be injured by broken
glass pieces in case the plasma display breaks.
14. Overloading—Do not overload AC outlets or extension cords.
Overloading can cause fire or electric shock.
15. Entering of objects and liquids—Never insert an object into
the product through vents or openings. High voltage flows in
the product, and inserting an object can cause electric shock
and/or short internal parts. For the same reason, do not spill
water or liquid on the product.
16. Servicing—Do not attempt to service the product yourself.
Removing covers can expose you to high voltage and other
dangerous conditions. Request a qualified service person to
perform servicing.
17. Repair—If any of the following conditions occurs, unplug the
power cord from the AC outlet, and request a qualified service
person to perform repairs.
a. When the power cord or plug is damaged.
b. When a liquid was spilled on the product or when objects
have fallen into the product.
c. When the product has been exposed to rain or water.
d. When the product has been dropped or damaged.
e. When the product displays an abnormal condition. Any
noticeable abnormality in the product indicates that the
product needs servicing.
18. Replacement parts—In case the product needs replacement
parts, make sure that the service person uses replacement
parts specified by the manufacturer, or those with the same
characteristics and performance as the original parts. Use of
unauthorized parts can result in fire, electric shock and/or
other danger.
19. Safety checks—Upon completion of service or repair work,
request the service technician to perform safety checks to
ensure that the product is in proper operating condition.
20. Wall or ceiling mounting—When mounting the product on a
wall or ceiling, be sure to install the product according to the
method recommended by the manufacturer.
21. Heat sources—Keep the product away from heat sources
such as radiators, heaters, stoves and other heat- generating
products (including amplifiers).
22. Unplug the power cord from the AC outlet before installing
the speakers (for PRO-1150HD only).
23. Never expose the screen of the plasma display to a strong
impact, for example, by hitting it. The screen may be broken,
resulting in fire or personal injury.
24. Do not expose the plasma display to direct sunlight for a long
period of time. The optical characteristics of the front
protection panel changes, resulting in discoloration or warp.
25. The plasma display weighs about 40.8 kg (89.9 lbs.) for the
PRO-1150HD (including the stand and speaker) and about
31.8 kg (70.1 lbs.) for the PRO-950HD (including the stand).
Because it has small depth and is unstable, unpack, carry,
and install the product with one more person at least and use
the handles.
Safety Precautions
Installation Precautions
Observe the following precautions when installing with any items such as the optional bracket.
When using the optional brackets or equivalent items
• Ask your dealer to perform the installation.
• Be sure to use the supplied bolts.
• For details, see the instruction manual that comes with the optional bracket (or equivalent items).
When using other items
• Consult your dealer.
• The following six mounting holes can be used for the installation:
Rear view (PRO-1150HD)
Side view
02
Mounting surface
Mounting holeMounting hole
4 5
Median line
Rear view (PRO-950HD)
Mounting
hole
45
Mounting hole
Median line
Median line
Plasma
display
Mounting
bracket (or
equivalent item)
M8 screw
12 mm to 18 mm
(0.5 inches to 0.7 inches)
Median line
Caution
• Be sure to use four or more mounting holes symmetrical to the vertical and horizontal median lines.
• Use M8 screws, which go 12 mm to 18 mm (0.5 inches to 0.7 inches) in depth from the mounting surface of the plasma display. See
the side view above.
• Be careful not to block the ventilation opening at the rear of the plasma display.
• Be sure to install the plasma display on a flat surface because it contains glass.
• The screw holes other than the above are to be used only for the specified products. Never use them for mounting non-specified
products.
Note
• It is strongly recommended to use the optional Pioneer mounting products.
• Pioneer shall not be liable for any personal injury or product damage that results from the use of mounting items other than the
optional Pioneer products.
11
En
03
Supplied Accessories
Chapter 3
Supplied Accessories
Screws (M4 x 10 mm) x 2
(for plastic bands)
Remote control unit
AA size batteries × 2
(Alkaline batteries for
remote control unit)
Speed clamps
Bead bands
Cleaning cloth
Plastic bands x 2
Power cord (2 m/6.6 feet)
Speaker accessories
×
3
×
3
(for PRO-1150HD only)
Speaker cables × 2
Speaker Mounting Fittings
12
En
Warranty card
Operating instructions
Bracket for BOTTOM-LEFT
Bracket for BOTTOM-RIGHT
Bracket for TOP-LEFT
Bracket for TOP-RIGHT
Speaker mounting screws
(M5
×
10 mm: Black) × 16
Part Names
Chapter 4
Part Names
Plasma display
(Front)
04
SidePRO-1150HDPRO-950HD
12
13
14
15
16
2
3
1
5
4
6
Viewed from below of the display
The terminals on side panels are common to the PRO-1150HD
and PRO-950HD.
1
Side
7
8
9
10
11
2
3
4
56
Viewed from the front side of the display
1a
button
(See page 26.)
2
POWER ON indicator
(See page 26.)
3
STANDBY indicator
(See page 26.)
4
SLEEP indicator
5
Room Light Sensor
6
Remote control sensor
7STANDBY/ON
8INPUT
9VOLUME UP/DOWN
buttons*)
10 CHANNEL UP/DOWN
buttons*)
button (
button
ENTER
button*)
buttons (
buttons (
UP/DOWN
LEFT/RIGHT
11 TV GUIDE
12
USB port
13
PHONES output terminal
14
INPUT 3 terminals (COMPONENT VIDEO: Y, PB,
R
)
P
15
INPUT 3 terminal (VIDEO)
16
INPUT 3 terminals (AUDIO)
The buttons with asterisks (*) can operate the TV Guide On
Screen™ system.
button*
13
En
04
Part Names
(Rear)
27
13
14
15
16
17
18
PRO-1150HDPRO-950HD
45
45
28
19
20
45
2625
21
22
567
23
24
*For exact terminal positions, refer to
the terminal position sheet located
near the terminal compartment.
213
9
10
8
11
12
4
45
13
14
15
16
17
18
45
1920
45
22
21
23
24
25
14
En
1
Ethernet cable port
2
CableCARD™ slot
3
ANT/CABLE A IN terminal
4
AC IN terminal
5
INPUT 4 terminal (HDMI)
6
INPUT 5 terminal (HDMI)
7
INPUT 6 terminal (HDMI)
8
INPUT 7 terminal (HDMI)
9
PC INPUT terminal (ANALOG RGB)
10
CONTROL OUT terminal (supports
11
RS-232C terminal (used for factory setup)
12
ANT B IN terminal
13
INPUT 1 terminal (S-VIDEO)
14
INPUT 1 terminal (VIDEO)
15
SUB WOOFER terminal
16
AUDIO OUT terminals (AUDIO)
SR+
The terminals from 1 to 12 are the same as the
PRO-1150HD.
17
INPUT 1 terminals (AUDIO)
18
INPUT 2 terminals (AUDIO)
19
INPUT 4 terminals (AUDIO)
20
INPUT 5 terminals (AUDIO)
21
INPUT 2 terminal (VIDEO)
22
IR REPEATER OUT terminal
23
DIGITAL OUT terminal (OPTICAL)
24
PC INPUT terminal (AUDIO)
25
INPUT 2 terminals (COMPONENT VIDEO: Y, PB,
R
)
)
P
26
SPEAKERS (R/L) terminals
27
SPEAKERS (R) terminal (Speaker side)
28
SPEAKERS (L) terminal (Speaker side)
Part Names
Remote control unit
This section describes the functions of the buttons available
when the mode switch has been set to TV. For the buttons for
controlling other equipment, see Using the remote control unit to control other devices starting from page 99.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Mode switch
(with “TV” selected)
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
1TV
a:
Turns on the power to the plasma display or places it
into standby mode.
2
Transmission confirmation LED
3INPUT
4SCREEN SIZE
5AV SELECTION
6INFO
7HOME MENU
8DAY +/–
9
10 HDMI CONTROL
11 FAVORITE CH (A, B, C, D)
12 0 to 9
13 •(dot)
14 CH +/–
15 SPLIT
16 FREEZE
17 MTS
18 D
19 ANT
20 PC
21 DISPLAY
22 TV GUIDE
23 ENTER
24 PAGE +/–
25 RETURN
26 HOME MEDIA GALLERY
27 CH ENTER
28 CH RETURN
29 VOL +/–
30 M MUTING
31 SHIFT
32 SWAP
: Selects an input source of the plasma display.
(“INPUT 1”, “INPUT 2”, “INPUT 3”, “INPUT 4”, “INPUT 5”,
“INPUT 6” and “INPUT 7”)
: Displays a channel banner when a TV program is being
watched.
When the TV Guide On Screen™ system is in operation, displays
information about the currently highlighted channel (if available).
MENU
system is in operation.
in the TV Guide On Screen™ Listing service.
///: Selects a desired item on the menu screen.
Selects any of the four preset channels. See page 42 for details
to set the FAVORITE CH.
While watching, you can toggle the set channels by pressing
B, C
and D.
: Switches the screen mode among 2-screen, picture-in-
picture, and single-screen.
cancel the function.
: Selects MTS/SAP or language depending on the program
being watched.
: Lights up all buttons
Lights turn off if no operations are performed within five
seconds. This is used for remote control use in dark locations.
: Selects the antenna (A, B). See page 23 for details.
: Selects the PC terminal as an input source.
program listing screen vertically.
screen.
disabled while the TV Guide On Screen™ system is displayed.
picture-in-picture mode.
or picture-in-picture mode.
: Selects the screen size.
: Selects audio and video settings.
: Displays the HOME MENU screen.
: Displays a panel menu when the TV Guide On Screen™
: Jumps to the next or previous day of program listings
: Displays the HDMI Control menu.
:
: Selects the channel.
: Enters a dot.
: Selects the channel.
: Freezes a frame from a moving image. Press again to
: Displays the channel information.
: Displays the TV Guide On Screen™ system.
: Executes a command.
(for the TV Guide On Screen™ system): Scrolls the
: Returns to the previous menu screen.
: Displays the Home Media Gallery
: Executes a channel number.
: Returns to the previous channel. This button is
: Sets the volume.
: Mutes the sound.
: Moves the location of the small screen when in the
: Switches between the two screens when in the 2-screen
(AV source:
04
A
,
Note
• When using the remote control unit, point it at the plasma
display.
• See pages 92 to 102 for operating buttons not listed on this
page.
15
En
05
Preparation
Chapter 5
Preparation
Installing the plasma display
Over 50 cm
(19 11/16 inches)
Over 10
cm
(3 15/16
inches)
Location
• Avoid direct sunlight. Maintain adequate ventilation.
Note
• Allow enough space around the upper and back parts when
installing to ensure adequate ventilation of the rear of the unit.
Moving the plasma display
Because the plasma display is heavy, be sure to have someone
help you when moving it.
(PRO-1150HD)
(PRO-950HD)
Caution
When installing on a rack, etc., hold the plasma display.
Installing the Pioneer speaker
(PRO-1150HD)
Caution
• Do not move the display holding on to the mounting fittings.
This can result in injury or damage to the unit.
About the speaker
• In order to prevent damage to the speaker system resulting
from input overload, please observe the following precautions:
• Do not use the speaker with anything other than the plasma
display. Doing so may result in damage or fire.
• Be sure to turn the connected devices off and remove the
power cord from the power outlet beforehand when changing
the connection or installation method.
• When using a tone control function to greatly emphasize treble
sounds, do not use excessive amplifier volume.
• Please handle the speaker with sufficient care, as the grille net
and the cabinet can become damaged or broken when they are
subjected to strong external impacts.
• Placing a CRT computer screen or CRT monitor near to the
speaker may result in interference or color distortion. If this
happens, distance the monitor from the speaker.
Installation
• When installing the speaker, do not use any screws other than
those supplied, otherwise the speaker may come off from the
main unit and fall over.
• When installing the speaker, tighten the screws firmly.
16
En
Preparation
PRO-1150HD with the speaker installed
(with the Pioneer table top stand)
Speaker mounting fitting
(for TOP-RIGHT)
Speaker mounting
screw (M5 x 10 mm)
Speaker mounting
screw (M5 x 10 mm)
05
Speaker mounting fitting
(for TOP-LEFT)
Speaker mounting screw
(M5 x 10 mm)
SpeakerSpeaker
Bead band
(Accessories of the
Speaker mounting fitting
(for BOTTOM-RIGHT)
Speaker mounting screw
(M5 x 10 mm)
Speaker mounting
screw (M5 x 10 mm)
Speed clampSpeed clamp
plasma display)
Speaker cable
Note
• Before installing the speaker, make sure that the Pioneer
table top stand is attached to the plasma display.
• When using the hang on wall unit, first lay the plasma
display on top of a soft sheet, etc., remove the stand, then
attach the speaker.
1. Attach the speaker mounting fittings to the
speakers.
• There is a left speaker and a right speaker. When you are
mounting them, check the label on the back to get them
right.
• There are top and bottom speaker mounting fittings for
both the left and the right speaker. Attach the appropriate
fittings to the top and the bottom on the back of the
speakers using the supplied screws.
(It shows the attachment of the fitting on the right side. It
is attached on the left side by the same procedure.)
Speaker mounting
screw (M5 x 10 mm)
Speed clamp
Speaker mounting fitting (For TOP-RIGHT)
(The skinny slot is used for mounting to the top.)
Speaker mounting fitting
(For BOTTOM-RIGHT)
Screw holes
Speaker mounting screw
(M5 x 10 mm)
Speaker mounting fitting
(for BOTTOM-LEFT)
Speaker mounting screw
(M5 x 10 mm)
Screw holes
Speaker mounting fitting
(For BOTTOM-RIGHT)
Place the speaker so its terminals
(bottom) are facing you.
Speaker mounting fitting
(For TOP-RIGHT)
17
En
05
Preparation
2. Screw a supplied screw into the speaker
mounting hole (lower of the two) at the top,
rear of the display.
• Do not tighten it all the way yet. Leave it loose, with about
5 mm left to tighten.
Speaker
mounting
hole
Top of display
Leave a space of about 5 mm
Top, back of
display
5 mm
3. Hang the speaker mounting fitting on the
screw you installed at the top by passing the
wide part over it and lowering into the slot;
screw in the lower screw temporarily.
After passing the wide part of the hole of the speaker
mounting fitting (top) over the screw, lower the speaker onto
it.
After passing the
wide part of hole
over the screw, lower
the speaker.
4. Adjust the position of the speaker and then
tighten the upper and lower screws firmly.
5. Tighten the two screws, at the top and
bottom for each speaker (total of four
screws), thus fixing the speakers to the
display.
6. Pass the supplied speaker cable between the
speaker and the plasma display (below the
speaker mounting fitting) from below.
7. Connect the speaker cables to the speaker
(see next page).
8. Insert the cable in the groove on the speaker.
Speaker cable
Speaker terminal
Insertion in
groove
18
En
Tighten with the
provided screw the
bottom speaker
mounting fitting to the
display temporarily
(one place bottom).
9. Connect the other end of the speaker cables
to the rear of plasma display (see next page).
Preparation
speaker cables
05
Connecting the speaker cables
to the rear of plasma display.
GrayGray
Connect the cables correctly with respect to
the polarity of the plasma display speaker
terminals, that is, cable (Gray) to
terminals (Red) and cable (Black) to
terminals (Black).
Black
BlackRedRed
Speaker terminal
Connecting the speaker cables
to the speaker.
Black
Black
Connect the cables correctly with respect to
the polarity of the speaker terminals, that is,
cable (Gray) to terminals (Red) and
cable (Black) to terminals (Black).
Red
Gray
Speaker terminalSpeaker cableSpeaker terminal
Note
• Press the lever and insert the end of the cable.
• When you release the lever, it
clamps onto the speaker cable.·
Caution
• Be sure to turn the connected
devices off and remove the power
cord from the wall outlet beforehand when changing the
connection or installation method.
• If you insert the speaker cable too far so that
the insulation is touching the speaker
terminal, you may not get any sound.
Lever
• Check if the end of the speaker cables are securely connected
to the terminals by slightly tugging on the cable after making
connections. Loose connections may result in sound dropouts
or noise.
• If there is a short in the and cables caused by an exposed
lead wire, excessive load may be applied to the plasma display,
resulting in interrupted operation or malfunction.
• Incorrect connections of the speaker cable to the right or left of
the plasma display terminals with respect to the polarity may
result in insufficient stereo sound effects, delivering poor bass
sounds or unstable sound image.
• Bundle the cable without pulling.
19
En
05
Wood screw
Supplied screw
Supplied screwSupplied screw
Preparation
Preventing the plasma display from
falling over
After installing the stand, be sure to take special care to ensure
that the plasma display will not fall over and is stabilized to both
the wall and rack.
Stabilizing on a table or rack
Stabilize the plasma display as shown in the diagram using the
supplied plastic bands and screws.
Note
• To stabilize the plasma display on a table or rack, also use
commercially available wood screws that have a nominal
diameter of 4 mm (5/32 inch) and that are at least 20 mm
(13/16 inch) long.
4 mm
(5/32 inch)
(3/8 inch to 5/8 inch)
20 mm min.
(13/16 inch)
4 5
Wood screw
(commercially available,
4 mm x 20 mm min.)
(5/32 inch x 13/16 inch)
8 mm to 15 mm
Supplied screw
(M4 x 10 mm)
Note
• Use hooks, cords and fittings that are available on the market.
Recommended hook: Nominal diameter 8 mm, length 12 mm
to 18 mm (0.5 inches to 0.7 inches)
M8
12 mm to 18 mm
(0.5 inches to 0.7 inches)
1. Hook
2. Cord
Fitting
4
5
Caution
• A table or rack with adequate strength should always be used
to support the plasma display. Failure to do so could result in
personal injury and physical damage.
• When installing the plasma display, please take the necessary
safety measures to prevent it from falling or overturning in case
of emergencies, such as earthquakes, or of accidents.
• If you do not take these precautions, the plasma display could
fall down and cause injury.
• The screws, hooks, cords and other fittings that you use to
secure the plasma display to prevent it from overturning will
vary according to the composition and thickness of the surface
to which it will be attached.
• Select the appropriate screws, hooks, cords, and other fittings
after first inspecting the surface carefully to determine its
thickness and composition and after consulting a professional
installer if necessary.
Drill a hole in the middle at the rear of the tabletop panel before
using a wood screw. Perform this work the same way on the left
and right sides.
Using a wall for stabilization
1Attach falling prevention bolts (hooks) to the plasma
display.
2Use strong cords to stabilize it appropriately and
firmly to a wall, pillar, or other sturdy element.
Perform this work in the same way on the left and right sides.
20
En
Preparation
05
Attaching/detaching the Pioneer stand
The plasma display comes with the Pioneer table top stand
attached. You can also install the display on a rack by detaching
the stand. The method for attaching/detaching the stand varies
depending on the product.
Caution
• This product can be used only with the attached stand. Using
other stands can result in instability, possibly causing injury.
• The weight of a 50 inch plasma display is about 34.8 kg (76.7
lbs.) and a 42 inch about 29.9 kg (65.9 lbs.), it has no depth, and
is unstable. Therefore, at least two people must assemble and
install it.
Detaching the stand
• Steps for detaching the stand are the same for PRO1150HD and PRO-950HD. Illustrations shown are for PRO1150HD.
1With the plasma display lying flat, loosen and remove
the two installation bolts (1) and (2) using a
screwdriver.
Installation bolts (1): M8 x 23 mm (black) for PRO-950HD
M8 x 23 mm (black) for PRO-1150HD
Installation bolts (2): M8 x 60 mm (black) for PRO-950HD
M8 x 40 mm (black) for PRO-1150HD
Note
• Make sure to keep the installation bolts (1) and (2) that have
been removed as they are re-used when attaching the stand to
the plasma display.
• Place a sheet or protective cover to protect the display from
scratches or damage.
• Work only with the plasma display lying flat on a table or similar
surface.
• When lying the plasma display down, be careful not to scratch
or damage it.
• If the speaker has been installed, it is recommended to detach
the speaker before removing the stand (for PRO-1150HD only).
Attaching the stand again
• Steps for attaching the stand are the same for PRO1150HD and PRO-950HD (use the screw holes with “T”
inscribed). Illustrations shown are for PRO-1150HD.
1With the plasma display lying flat, fit the stand’s
support columns to the bottom of the plasma display as
indicated by the arrows, then slowly insert them.
• Be extremely careful not to insert the support columns of
the stand into any part of the plasma display other than the
stand insertion slots. Doing so might damage the plasma
display panel or its ports or result in warping of the stand.
Line up the column supports
with the bottom of the
plasma display, as indicated
in the accompanying
diagram.
Installation bolts (1)
Installation bolts (2)
Table top stand
Sheet
2Remove the stand from the plasma display.
(Step 1)
(Step 2)
Plasma
display
Insert the stand into the
plasma display so that an
arrow with “FRONT/FACE
AVANT” mark inscribed at
the bottom of the stand
indicates downward.
Sheet
21
En
05
Preparation
2Attach the stand at the points indicated by the arrows
and tighten the installation bolts (2) and (1) firmly using
a screwdriver.
Installation bolts (1): M8 x 23 mm (black) for PRO-950HD
M8 x 23 mm (black) for PRO-1150HD
Installation bolts (2): M8 x 60 mm (black) for PRO-950HD
M8 x 40 mm (black) for PRO-1150HD
Screw hole with “T” inscribed
Installation bolts (1)
Installation bolts (2)
(Step 2)
(Step 1)
3Replace the plasma display to stand upright.
For speaker installation, see Installing the Pioneer speaker on pages 16 (PRO-1150HD only).
Note
• Be sure to install the plasma display in a flat, stable location.
• Insert the screws into the holes vertically and tighten them.
• Place a sheet or protective cover to protect the display from
scratches or damage.
• Work only with the plasma display lying flat on a table or similar
surface.
• When lying the plasma display down, be careful not to scratch
or damage it.
• If the speaker has been installed, it is recommended to detach
the speaker before attaching the stand (for PRO-1150HD only).
22
En
Preparation
05
Cable connections for watching digital
and/or conventional TV channels
This system is equipped with two terminals for inputting TV
broadcasting signals: ANT/CABLE A IN and ANT B IN. The ANT/
CABLE A IN terminal accepts both digital and conventional TV
broadcasting signals while the ANT B IN terminal accepts only
conventional TV broadcasting signals. When using cable TV to
watch digital and/or conventional TV channels, connect to the
ANT/CABLE A IN terminal as shown. In addition, you may
connect an antenna to the ANT B IN terminal as shown; use an
outdoor antenna to enjoy clearer pictures. If your outdoor
antenna uses a 75-ohm coaxial cable with an F-type connector,
plug it into the antenna terminal at the rear of the plasma display.
Connecting VHF/UHF antennas and a Cable
VHF antenna
U/Vmixer
4 5
UHF antenna
Inserting the CableCARD™
The plasma display is equipped with a slot for inserting a
CableCARD™. When you are watching digital and/or High
Definition TV channels over cable, the card allows you to use the
POD service provided by the cable TV company; the POD stands
for Point of Deployment. This service presents various types of
useful information, using HTML text.
1Confirm that the ANT/CABLE A IN terminal has been
connected with the coaxial cable from the Cable
Converter.
2Hold and push the tab of the slot cover on the rear of
the plasma display leftward, and remove the cover
while pulling the tab’s latch downward.
(Viewed from below of the
plasma display)
1
Tab
2
Rear view
Coaxial
Coaxial
Cable TV
Note
• Be sure to connect coaxial cables as shown above. Signal
reception may fail if not properly connected.
• In order to watch cable TV channels, be sure to connect the
cable to the ANT/CABLE A IN terminal.
• The ANT/CABLE A IN and ANT B IN terminals must not receive
the same signals. For example, do not connect a cable from a
cable TV to both the ANT/CABLE A IN and ANT B IN terminals.
Similarly, do not connect a cable from an antenna to both the
ANT/CABLE A IN and ANT B IN terminals.
• TV Guide may not be available in all areas and is not available
with satellite systems. In addition, as content providers move to
digital programming and broadcasting, TV Guide Data may be
unavailable or become unavailable.
3Insert the specified CableCARD™ into the Cable CARD
slot as far as it goes.
Note
• Be sure to insert only the specified CableCARD™.
• Do not insert a PC card.
• When you use a CableCARD™, you need not execute Auto
Channel Preset; the CableCARD™ automatically generates a
cable channel list.
23
En
05
Preparation
Routing cables
When the speaker is installed under the plasma display panel
(for PRO-1150HD only)
Rear view
Speaker cable
Bead band
Speed clampSpeed clamp
Bead band
Speed clamp
Attaching speed clamps to the main unit
Attach the speed clamps using the three holes (42 inches: two
holes) marked with below, depending on your routing system.
for PRO-1150HD
Attaching and removing speed clamps
Insert [1] into an appropriate hole on the rear of the plasma
display and snap [2] into the back of [1] to lock the clamp. Speed
clamps are designed to be difficult to undo once in place. Please
attach them carefully.
Use pliers to twist the clamp 90º, pulling outward. The clamp may
deteriorate over time and become damaged if removed.
5
45
1
for PRO-950HD
Note
45
• Use the supplied bead bands and speed clamps as necessary.
• When tidying up your speaker cables, make sure to bundle
them so that they are not subjected to any pressure.
Connecting the power cord
Connect the power cord after all component connections have been completed.
Plasma display (rear view)
4 5
2
AC IN terminal is located
on the upper edge of the
compartment.
Caution
• Use only the supplied power cord.
• Be sure to use the specified power supply voltage;
neglecting this can result in fire or electric shock.
• For the plasma display, a three-core power cord
with a ground terminal is used for efficient
protection. Always connect the power cord to a
three-pronged outlet and make sure that the cord
is properly grounded.
24
En
Power cord
Partially eliminates noise
caused by the power source.
Note
• Always turn off the power of the plasma display when
connecting or disconnecting power cords.
• Disconnect the power cord from the power outlet when the
plasma display is not going to be used for a long period of time.
Noise filter
Preparation
05
Preparing the remote control unit
Inserting batteries
1Open the battery cover.
2Load the supplied two AA size batteries while inserting
their respective negative polarity (–) ends first.
• The battery polarities must correspond with the (+) and (–)
indicators in the battery compartment.
3Close the battery cover.
Allowed operation range of the remote control
unit
Operate the remote control unit while pointing it toward the
remote control sensor located at the bottom right of the front
panel of the plasma display. The distance from the remote control
sensor must be within 7 m (23 feet) and the angle relative to the
sensor must be within 30 degrees in the right or left direction.
7 m
30º
(23 feet)
30º
Remote control
sensor
Cautions regarding batteries
• The remote control unit cannot operate the system if the
batteries in the unit are weak. When this happens, replace the
batteries with new ones.
• When you replace the batteries, use alkaline batteries for the
remote control unit.
• Do not mix batteries of different types. Different types of
batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries
can shorten the life of new batteries or cause chemical leakage
in old batteries.
• Do not leave dead batteries in the remote control unit;
chemical leakage will occur. If you find any chemical leakage,
wipe thoroughly with a cloth.
• The batteries supplied with this product may have a shorter life
expectancy due to storage conditions.
• If you will not use the remote control unit for an extended
period of time, remove the batteries from it.
Battery disposal
When disposing of used batteries, please comply with
governmental regulations or environmental public
institution’s rules that apply in your country/area.
Note
• For the remote control sensor located on the PRO-950HD, see
Part Names on page 13
Cautions regarding the remote control unit
• Do not expose the remote control unit to shock, liquid, or high
humidity.
• Do not place the remote control unit under direct sunlight; the
unit may deform.
• The remote control unit may not work properly if the remote
sensor window of the plasma display is under direct sunlight or
strong lighting. In such case, change the angle of the lighting
or plasma display, or operate the remote control unit closer to
the remote sensor window.
• When any obstacle exists between the remote control unit and
the remote control sensor, the remote control unit may not
function.
• As the batteries become weak, the remote control unit can
function within a shorter distance from the remote control
sensor. Replace the batteries with new ones if necessary.
• The plasma display emits very weak infrared rays from its
screen. If you place such equipment operated through infrared
remote control as a VCR nearby, that equipment may not
receive commands from its remote control unit properly or
entirely. If this is the case, place that equipment at a location
far enough from the plasma display.
• Depending on the installation environment, infrared rays from
the plasma display may not allow this system to properly
receive commands from the remote control unit or may
shorten allowable distances between the remote control unit
and the remote control sensor. The strength of infrared rays
emitted from the screen differs, depending on images
displayed on the screen.
25
En
06
Basic Operations
Chapter 6
Basic Operations
Turning on the power
•Press a on the plasma display when the POWER ON and
STANDBY indicators are off.
• The POWER ON indicator on the plasma display lights up
blue.
•Press TV a on the remote control unit or STANDBY/ON
on the plasma display if the STANDBY indicator lights up
red.
• The POWER ON indicator on the plasma display lights up
blue.
Turning off the power
(to standby mode)
1Press TV a on the remote control unit or STANDBY/ON
on the plasma display.
• The system enters the standby mode and the image on the
screen disappears.
•The STANDBY indicator lights up red.
• This will allow the system to automatically receive digital
TV program information while in the standby mode.
Note
• If you are not going to use this system for a long period of time,
remove the power cord from the power outlet.
Plasma display status indicators
The table below shows the operational status of the plasma
display. You can check the current status of the system with the
indicators on the plasma display.
Indicator StatusSystem Status
POWER ONSTANDBY
The power cord of the plasma display has
been disconnected. Or, the power cord of
the plasma display has been connected but
the a button of the plasma display is off.
Power to the system is on.
The system is in the standby mode.
Caution
• While the POWER ON and STANDBY indicators are off, the
system cannot be placed into the power-on mode even when
TVa or STANDBY/ON button is pressed. Press a on the
plasma display.
• The plasma display will still consume some power as long as
the power cord is inserted into the power outlet.
Plasma display
(PRO-1150HD)
a
button
POWER ON indicator
STANDBY indicator
(PRO-950HD)
POWER ON
indicator
STANDBY
indicator
a
button
Viewed from below of the display (left).
STANDBY/ON
button
For other than the above, see Troubleshooting on page 103.
Note
• You can select “Auto”, “High”, “Mid” or “Low” for the brightness
of the POWER ON indicator. When “Auto” is selected, the
brightness of the indicator changes to “High”, “Mid” or “Low”
to match the brightness level of the viewing area. For details,
see Blue LED Dimmer on page 64.
26
En
(Right side view)
Basic Operations
06
Watching TV channels
Unless you set up TV channels that you can watch under the
current conditions, you cannot tune in those channels. For the
procedure, see Setting up TV channels on page 36.
Note
• When watching a digital TV program, you may see emergency
alert messages scrolling at the top of the screen. Those
messages are broadcasted by TV stations as necessary when
in emergency situations.
Selecting the antenna
After confirming that the Mode switch on the remote control unit
has been set to “TV”, press ANT on the remote control unit to
select antenna A or B.
• Make this selection depending on the connections to the
antenna input terminals at the rear of the plasma display (page
23).
• While watching a broadcast, press ANT to view the image
received from the other antenna.
•Pressing ANT while watching in the multiscreen mode (TV
image and video image) with TV selected will display the TV
image of the other antenna.
•Pressing ANT while watching in the multiscreen mode with
two TV images displayed will not have any effect.
Plasma display (right side view)
CHANNEL +/–
Changing channels
To increase the channel number, press CH + on the remote
control unit. To decrease the channel number, press CH –.
• CHANNEL +/– on the plasma display operates the same as CH
+/– on the remote control unit.
•Press CH RETURN to switch the currently tuned channel to the
previously tuned channel.
Press CH RETURN again to restore the currently tuned
channel.
Using 0 to 9 and • (dot) on the remote control unit
Select channels directly by pressing buttons 0 to 9. To select
subchannels, also use the • (dot) button.
EXAMPLE
• To select channel 5 (one-digit channel), press 5.
• To select channel 25 (two-digit channel), press 2 then 5.
• To select channel 125 (three-digit channel), press 1, 2, then 5.
• To select subchannel 10.01, press 1, 0, • (dot), 0, then 1.
• After entering a channel or subchannel number, you may
press CH ENTER to tune in the channel more quickly.
• Each time you change a channel, a channel banner appears
that shows information about the currently selected channel.
To clear the channel banner, press INFO.
• If you do not setup the TV Guide On Screen™ system, the
channel banner may not display certain types of program
information.
Channel banner
12:33pm
DTV 2 • 1002.102 A
XXXXXXXXXX
12:30pm — 2:00pm
XXX
27
En
06
Basic Operations
Changing the volume and sound
• VOLUME +/– on the plasma display operates the same as VOL
+/– on the remote control unit.
Plasma display (right side view)
VOLUME +/–
To increase the volume, press VOL + on the remote control unit.
To decrease the volume, press VOL –.
Changing the language
If you have selected a digital TV program that provides multilanguage services, you can switch among the languages by
pressing MTS on the remote control unit.
Each time you press MTS, the language switches.
Note
• Switchable languages differ depending on the current
broadcast.
• If the language selected through language setting is available
when the channel or program is changed, you will hear that
language.
• If you are watching a digital TV program without sound or
language information, “N/A” appears on the screen. With a
language other than English, French, and Spanish are
selected, “Others” will appear.
Volume adjustment display
• To mute the sound output, press MUTING. “” appears on
the screen. To quit muting, press MUTING again. Pressing
VOL + also quits muting.
Muting display
28
En
Basic Operations
06
Setting MTS/SAP mode
When watching conventional TV programs, you may enjoy stereo
sound and/or Secondary Audio Programs (SAP), using the Multichannel Television Sound (MTS) function.
• Stereo broadcasts
You can enjoy, for example, sports, shows, and concerts in
dynamic stereo sound.
• SAP broadcasts
MAIN sound: The normal program soundtrack (either in mono
or stereo).
SAP sound: Listen to second language, supplementary
commentary and other information. (SAP is mono sound.)
Note
• Conventional TV channels in this manual designate TV
channels that are received through the conventional VHF/UHF
frequencies or conventional cable TV channels.
• When stereo sound is difficult to hear, you may manually
switch to the MONO mode to obtain clearer sound.
• Once the MONO mode is selected, the plasma display sound
remains mono even if the system receives a stereo broadcast.
You must reselect the STEREO mode if you want to hear stereo
sound again.
• Selecting MTS while the input source is INPUT 1 to INPUT 7 or
PC does not change the type of sound. In this case, sound is
determined by the video source.
•The MTS button is disabled while the TV Guide On Screen™
system is displayed.
• In each of the MTS/SAP modes selected, the display changes
depend on broadcast signals being received.
When receiving STEREO sound signals
A 125
STEREO
A 125
STEREO
A 125
MONO
In STEREO mode
In SAP mode
In MONO mode
When receiving MONO + SAP sound signals
A 125
MONO (SAP)
A 125
SAP (MAIN)
A 125
MONO (SAP)
In STEREO mode
In SAP mode
In MONO mode
When receiving STEREO + SAP sound signals
A 125
STEREO (SAP)
In STEREO mode
Each time you press MTS, MTS toggles as shown below.
STEREO mode
STEREO
SAP mode
SAP
MONO mode
MONO
A 125
SAP (STEREO)
A 125
MONO (SAP)
In SAP mode
In MONO mode
When receiving MONO sound signals
A 125
MONO
A 125
MAIN
A 125
MONO
In STEREO mode
In SAP mode
In MONO mode
29
En
06
Basic Operations
Viewing a channel banner
While watching a TV program, pressing INFO causes the
following banner to appear. Pressing INFO again causes the
banner to disappear.
2
1
12:33pm
DTV 2 • 1002.102 A
XXXXXXXXXX
12:30pm — 2:00pm
5
678
3
XXX
4
1Station name
2Current time
3Channel number
4Input (Ant. A or Ant. B)
5Program title
6Program time schedule
7Channel logo
8TV rating name or icon
Using the multiscreen functions
Splitting the screen
Use the following procedure to select the 2-screen or picture-inpicture mode.
2-screen
Picture-in-picture
Note
• The above information is not displayed if not included in
broadcast signals.
• If you do not setup the TV Guide On Screen™ system, the
channel banner may not display certain types of program
information.
Using the POD service
If you have watched digital and/or High Definition TV channels
over cable, you can use the POD service provided by the cable TV
company. This service presents various types of useful
information, using HTML text.
1Press SPLIT to select the display mode.
• Each time you press SPLIT, the display mode is switched
among 2-screen, picture-in-picture, and single-screen.
Press HOME MENU, 9, 9, then 9 to view the POD display.
30
En
Loading...
+ 90 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.