Pioneer PRO-1120HD, PRO-920HD User Manual
PLASMA DISPLAY SYSTEM
PRO-1120HD
PRO-920HD
Register Your Product on
www.pioneerelectronics.com
Operating Instructions
11)
1)
Read these instructions.
2)
Keep these instructions.
3)
Heed all warnings.
4)
Follow all instructions.
5)
Do not use this apparatus near water.
6)
Clean only with dry cloth.
7)
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8)
Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9)
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10)
Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
Only use attachments/accessories specified by the
manufacturer.
12)
Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
13)
Unplug this apparatus during lightning storms or
when unused for long periods of time.
14)
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
Note to CATV system installer.
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particular, specifies that the cable ground–shall be connected to the
grounding system of the building, as close to the point of cable entry as practical.
WARNING: THE APPARATUS IS NOT WATER-
PROOFS, TO PREVENT FIRE OR SHOCK HAZARD, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE
AND DO NOT PUT ANY WATER SOURCE NEAR THIS
APPARATUS, SUCH AS VASE, FLOWER POT, COSMETICS CONTAINER AND MEDICINE BOTTLE ETC.
WARNING: Handling the cord on this product or
cords associated with accessories sold with the product will expose you to lead, a chemical known to the
State of California and other governmental entities to
cause cancer and birth defects or other reproductive
harm. Wash hands after handling.
NOTE: This equipment has been tested and found to
comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and
receiver.
— Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV tech-
nician for help.
Information to User
Alteration or modifications carried out without appropriate authorization may invalidate the user’s right to
operate the equipment.
CAUTION:
This product satisfies FCC regulations when shielded
cables and connectors are used to connect the unit to
other equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded cables and connectors for connections.
FEDERAL COMMUNICATIONS COMMISSION
DECLARATION OF CONFORMITY
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
Product Name: Plasma Display System
(Plasma Display)
(Media Receiver)
Model Number: PRO-1120HD PRO-920HD
(PRO-505PU) (PRO-435PU)
(PRO-R05U) (PRO-R05U)
Product Category: Class B Personal Computers & Peripherals
Responsible Party Name: PIONEER ELECTRONICS
(USA), INC., Customer Support Div.
Address: P.O. BOX 1760, LONG BEACH, CA., 90801-1760
U.S.A.
Phone: (800) 421-1625
For Business Customer URL
http://www.PioneerUSA.com
IMPORTANT NOTICE: The serial number for this
equipment is located on the rear panel. Please write this
serial number on your enclosed warranty card and keep
it in a secure area. This is for your security.
WARNING: Be sure to plug this equipment into a
grounding-type AC outlet.
English
[For Canadian model]
This Class B digital apparatus complies with Canadian
ICES-003.
Contents
Thank you for buying this Pioneer product.
Please read through these operating instructions so you will know how to operate your model properly. After you have finished
reading the instructions, put them away in a safe place for future reference.
In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown in the explanatory drawings. However the method of connecting and operating the unit is the same.
01 Important User Guidance Information
02 Safety Precautions
03 Operational Precautions
04 Supplied Accessories
Plasma Display ................................................................... 11
Media Receiver.................................................................... 11
05 Part Names
Plasma Display ................................................................... 12
Media Receiver.................................................................... 12
Remote control unit ............................................................ 14
06 Preparation
Installing the Plasma Display ............................................ 15
Installing the Media Receiver ............................................ 16
Installing the Media Receiver vertically ...................... 16
Connecting the system cable ............................................ 18
Routing cables .................................................................... 19
Preparing the remote control unit ..................................... 20
Inserting batteries ......................................................... 20
Cautions regarding batteries ....................................... 20
Allowed operation range of the remote
control unit .................................................................... 20
Cautions regarding the remote control unit .............. 20
Cable connections for watching digital and/or
conventional TV channels .................................................. 21
Connecting VHF/UHF antennas and a Cable
Converter ....................................................................... 21
Cable connections for watching digital
TV channels over air (VHF/UHF) ........................................ 21
Connecting VHF/UHF antennas .................................. 21
Switching between antenna A and B ............................... 22
Inserting the cable card ..................................................... 22
Connecting the power cord ............................................... 23
07 Basic Operations
Turning on the power (Standby) ........................................ 24
Turning off the power (Standby) ........................................ 24
Watching TV channels........................................................ 25
Selecting the antenna .................................................. 25
Changing channels ...................................................... 25
Changing the volume and sound ................................ 26
Viewing a channel banner ........................................... 26
Using the POD service ................................................. 27
Changing the language................................................ 27
Setting MTS/SAP mode ............................................... 27
Using the multiscreen functions ....................................... 28
Splitting the screen ...................................................... 28
Freezing images ............................................................ 29
08 Menu Setup
Menu configuration ............................................................ 30
AV mode menus ............................................................ 30
PC mode menus ........................................................... 30
Menu operations .................................................................30
09 Tuner Setup
Setting up TV channels ...................................................... 31
Using Auto Channel Preset ......................................... 31
Setting for skipping unwanted channels.................... 31
Setting up TV channels manually ............................... 31
Naming TV channels .................................................... 32
Checking signal strength ............................................. 32
Checking the Cable Card ID ........................................ 32
Enabling data acquisition ............................................ 32
Parental Control .................................................................. 33
Changing the password ............................................... 33
Clearing the password ................................................. 34
Activating the Parental Control ................................... 34
Setting the voluntary movie rating system
(MPAA) .......................................................................... 34
Setting the TV ratings ................................................... 35
Setting the TV Parental Guidelines (TV Guidelines) ... 35
Blocking Not Rated TV programs ................................ 35
Canadian rating systems ............................................. 36
Setting Canadian English ratings ............................... 36
Setting Canadian French ratings ................................ 37
Temporarily deactivating the Parental Control ........... 37
Setting your favorite channels ........................................... 37
Setting up closed captions ................................................ 37
Activating the closed caption ...................................... 38
Selecting the type of conventional closed captions .. 38
Selecting digital closed captions ................................ 38
Selecting digital closed caption parameters ............. 38
Clock Setting ....................................................................... 39
4
En
Contents
10 Adjustments and Settings
Sleep Timer .......................................................................... 40
AV Selection ........................................................................ 40
Picture adjustments ........................................................... 41
Pro Adjust ...................................................................... 41
Color Management ....................................................... 42
Sound adjustments ............................................................ 43
FOCUS ........................................................................... 43
Front Surround .............................................................. 43
Power Control ...................................................................... 44
Energy Save ................................................................... 44
No Signal off (AV mode only) ....................................... 44
No Operation off (AV mode only)................................. 44
Power Management (PC mode only) .......................... 44
Adjusting image positions (AV mode only) ...................... 45
Adjusting image positions and clock automatically
(PC mode only) .................................................................... 45
Adjusting image positions and clock manually
(PC mode only) .................................................................... 45
Selecting a screen size ....................................................... 46
Changing the brightness at both sides of the screen
(Side Mask) .......................................................................... 47
Language setting ................................................................ 47
11 Timer Presetting
Presetting TV programs using the timer ........................... 48
Priority rules for overlapped presettings ........................... 49
12 Enjoying through External Equipment
Watching a DVD image ...................................................... 50
Connecting a DVD player ............................................. 50
Displaying a DVD image .............................................. 50
Watching a VCR image ...................................................... 50
Connecting a VCR ........................................................ 50
Displaying a VCR image ............................................... 50
Using HDMI Input ............................................................... 51
Connecting HDMI equipment ..................................... 51
Enjoying a game console or watching camcorder
images ................................................................................. 52
Connecting a game console or camcorder ................ 52
Displaying an image of the game console or
camcorder ..................................................................... 52
Recording digital TV programs using a VCR or
DVD recorder ....................................................................... 52
Avoiding unwanted feedback ...................................... 52
Connecting a recorder ................................................. 53
Connecting other audio equipment .................................. 53
Connecting an AV receiver .......................................... 53
Watching a D-VHS image ................................................... 54
What is i.LINK? .............................................................. 54
Which i.LINK devices are connectable? ..................... 54
What can be recorded through i.LINK? ...................... 54
Connecting D-VHS recorders ...................................... 54
When connecting a single D-VHS recorder ............... 54
When connecting two D-VHS recorders..................... 54
Displaying a D-VHS image ................................................. 55
Useful and important notification ............................... 55
Setting up for controlling a D-VHS recorder .............. 56
Editing the i.LINK list .................................................... 56
Setting up for i.LINK standby....................................... 57
Operating the control panel screen ............................ 57
Watching an image from a personal computer ............... 58
Connecting a personal computer ............................... 58
Displaying an image from a personal computer ....... 58
Computer compatibility chart ............................................ 58
Connecting the VCR controller .......................................... 59
The lists of controllable recording
equipment manufactures ............................................ 60
Connecting control cords .................................................. 61
About SR+ .................................................................... 61
13 Useful Remote Control Features
Learning function of the remote control unit ................... 62
Using the learning function ......................................... 62
Presetting manufacture codes .................................... 62
Manufacture codes ...................................................... 63
Using the remote control unit to control other
devices ................................................................................. 64
Receiver control buttons .............................................. 64
Cable control buttons ................................................... 65
SAT control buttons ...................................................... 66
VCR control buttons ..................................................... 67
DVD/DVR control buttons ............................................ 68
14 Appendix
Troubleshooting .................................................................. 69
Specifications ...................................................................... 79
English
En
5
01 Important User Guidance Information
In order to obtain maximum enjoyment from this Pioneer
PureVision PRO-1120HD/PRO-920HD Plasma Display System,
please first read this information carefully.
With the Pioneer PureVision PRO-1120HD/PRO-920HD, you can
be assured of a high quality Plasma Display System with longlife and high reliability. To achieve images of exceptional quality,
this Pioneer Plasma Display System incorporates state-of-theart design and construction, as well as very precise and highly
advanced technology.
The Pioneer PureVision PRO-1120HD/PRO-920HD incorporates
the latest in color filter technology – 1
Filter. This improves the color / picture reproduction of these
models as compared to previous models. It also eliminates the
need for a physical glass panel to be placed in front of the
plasma panel, which furthers Pioneer’s continued goal of
reducing environmental waste in consumer electronics, now
during the manufacturing process and in the future during the
recycling process.
Over the course of its lifetime, the luminosity of the Pioneer
PRO-1120HD/PRO-920HD Plasma Display System will diminish
very slowly, such as with all phosphor-based screens (for
example, a traditional tube-type television). To enjoy beautiful
and bright images on your Pioneer Plasma Display System for
many years to come, please carefully read and follow the usage
guidelines below.
st
Surface Pure Color
Usage guidelines
All phosphor-based screens (including conventional tube-type
televisions) can be affected by displaying static images for a
prolonged period. Plasma Display Systems are no exception to
this rule. After-image and permanent effects on the screen can
be avoided by taking some basic precautions. By following the
recommendations listed below, you can ensure longer and
satisfactory results from your plasma:
• Whenever possible, avoid frequently displaying the same
image or virtually still moving pictures (e.g. closed-captioned
images or video game images which have static portions).
• Avoid viewing the On Screen Display for extended periods,
from a DVD player, VCR, and all other components.
• Do not leave the same picture freeze-framed or paused
continuously over a long period of time, when using the still
picture mode from a TV, VCR, DVD player or any other
component.
• Images which have both very bright areas and very dark
areas side by side should not be displayed for a prolonged
period of time.
• When playing a game, the “GAME” mode setting within “AV
Selection” is strongly recommended. However, please limit its
use to less than 2 hours at a time.
•After playing a game, or displaying a PC image or any still
image, it is best to view a normal moving picture in the
“WIDE” or “FULL” screen setting for over 3 times longer than
the previous still/moving image.
•After using the Plasma Display System, always switch the
display to “STANDBY” mode.
Installation guidelines
The Pioneer PureVision PRO-1120HD/PRO-920HD Plasma
Display System incorporates a very thin design. To ensure
safety, please take the proper measures to mount or install the
Plasma Display, in order to prevent the unit from tipping over in
the event of vibration or accidental movement.
This product should be installed by using only parts and
accessories designed by PIONEER. Use of accessories other
than the PIONEER stand or installation bracket may result in
instability, and could cause injury. For custom installation,
please consult the dealer where the unit was purchased. To
ensure correct installation, experienced and qualified experts
must install the unit. PIONEER will not be held responsible for
accident or damage caused by the use of parts and accessories
manufactured by other companies.
To avoid malfunction and overheating when installing, make
sure that the vents on the main unit are not blocked. To ensure
proper heat emission:
• Distance the unit slightly from other equipment, walls, etc.
For the minimum space required around the unit, see pages
15 to 16.
• Do not fit the unit inside narrow spaces where ventilation is
poor.
• Do not cover with a cloth, etc.
• Clean the vents on the sides and rear of the unit to remove
dust build-up by using a vacuum cleaner set to its lowest
suction setting.
• Do not place the product on a carpet or blanket.
• Do not leave the product tilted over except the case of vertical
installation of the Media Receiver.
• Do not reverse the product.
Using the unit without proper ventilation may cause the
internal temperature to rise, and could result in possible
malfunction. When the surrounding or internal temperature
exceeds a certain degree, the display will automatically power
off in order to cool the internal electronics and prevent a
hazardous occurrence.
Malfunction can be caused by many factors: inappropriate
installation site, improper assembly/installation/mounting,
improper operation of or modifications made to this product.
However, PIONEER cannot be held responsible for accidents or
malfunction caused by the above.
The following are typical effects and characteristics of a
phosphor-based matrix display and as such, are not covered by
the manufacturer’s limited warranties:
•Permanent residual images upon the phosphors of the panel.
• The existence of a minute number of inactive light cells.
•Panel generated sounds, examples: Fan motor noise, and
electrical circuit humming / glass panel buzzing
6
En
Panel sticking and after-image lag
• Displaying the same images such as still images for a long
time may cause after-image lagging. This may occur in the
following two cases.
1. After-image lagging due to remaining electric
load
When image patterns with very high peak luminance are
displayed more than 1 minute, after-image lagging may occur
due to the remaining electric load. The after-images remaining
on the screen will disappear when moving images are
displayed. The time for the after-images to disappear depends
on the luminance of the still images and the time they had
been displayed.
2. After-image (lag image) due to burning
Avoid displaying the same image on the Plasma Display
continuously over a long period of time. If the same image is
displayed continuously for several hours, or for shorter periods
of time over several days, a permanent after-image may remain
on the screen due to burning of the fluorescent materials. Such
images may become less noticeable if moving images are later
displayed, but they will not disappear completely.
• The Energy save function can be set to help prevent damage
from screen burning (see page 44).
01Important User Guidance Information
English
About operations through i.LINK
PIONEER shall not always assure normal video/audio recording
or playback when a D-VHS is operated through i.LINK.
DO NOT PLACE THIS PRODUCT ON AN UNSTABLE CART,
STAND, TRIPOD, BRACKET, OR TABLE. THE PRODUCT MAY
FALL, CAUSING SERIOUS PERSONAL INJURY AND SERIOUS
DAMAGE TO THE PRODUCT. USE ONLY WITH A CART, STAND,
TRIPOD, BRACKET, OR TABLE RECOMMENDED BY THE
MANUFACTURER, OR SOLD WITH THE PRODUCT. FOLLOW
THE MANUFACTURE’S INSTRUCTIONS WHEN INSTALLING
THE PRODUCT AND USE MOUNTING ACCESSORIES
RECOMMENDED BY THE MANUFACTURER.
A PRODUCT AND CART COMBINATION SHOULD BE MOVED
WITH THE CARE. QUICK STOPS, EXCESSIVE FORCE, AND
UNEVEN SURFACES MAY CAUSE THE PRODUCT AND CART
COMBINATION TO OVERTURN.
En
7
02
Safety Precautions
Electricity is used to perform many useful functions, but it can
also cause personal injuries and property damage if improperly
handled. This product has been engineered and manufactured
with the highest priority on safety. However, improper use can
result in electric shock and/or fire. In order to prevent potential
danger, please observe the following instructions when installing, operating and cleaning the product. To ensure your safety
and prolong the service life of your product, please read the
following precautions carefully before using the product.
1. Read instructions—All operating instructions must be read
and understood before the product is operated.
2. Keep this manual in a safe place—These safety and
operating instructions must be kept in a safe place for
future reference.
3. Observe warnings—All warnings on the product and in the
instructions must be observed closely.
4. Follow instructions—All operating instructions must be
followed.
5. Cleaning—Unplug the power cord from the AC outlet before
cleaning the product. Use a damp cloth to clean the
product. Do not use liquid cleaners or aerosol cleaners.
6. Attachments—Do not use attachments not recommended
by the manufacturer. Use of inadequate attachments can
result in accidents.
7. Water and moisture—Do not use the product near water,
such as bathtub, washbasin, kitchen sink and laundry tub,
swimming pool and in a wet basement.
8. Stand—Do not place the product on an unstable cart,
stand, tripod or table. Placing the product on an unstable
base can cause the product to fall, resulting in serious
personal injuries as well as damage to the product. Use
only a cart, stand, tripod, bracket or table recommended by
the manufacturer or sold with the product. When mounting
the product on a wall, be sure to follow the manufacturer’s
instructions. Use only the mounting hardware
recommended by the manufacturer.
9. When relocating the product placed on a cart, it must be
moved with utmost care. Sudden stops, excessive force and
uneven floor surface can cause the product to fall from the
cart.
10. Ventilation—The vents and other openings in the cabinet
are designed for ventilation. Do not cover or block these
vents and openings since insufficient ventilation can cause
overheating and/or shorten the life of the product. Do not
place the product on a bed, sofa, rug or other similar
surface, since they can block ventilation openings. This
product is not designed for built-in installation; do not place
the product in an enclosed place such as a bookcase or
rack, unless proper ventilation is provided or the
manufacturer’s instructions are followed.
11. Power source—This product must operate on a power
source specified on the specification label. If you are not
sure of the type of power supply used in your home, consult
your dealer or local power company.
12. Power cord protection—The power cords must be routed
properly to prevent people from stepping on them or objects
from resting on them. Check the cords at the plugs and
product.
13. The plasma Display used in this product is made of glass.
Therefore, it can break when the product is dropped or
applied with impact. Be careful not to be injured by broken
glass pieces in case the plasma Display breaks.
14. Overloading—Do not overload AC outlets or extension
cords. Overloading can cause fire or electric shock.
15. Entering of objects and liquids—Never insert an object into
the product through vents or openings. High voltage flows
in the product, and inserting an object can cause electric
shock and/or short internal parts. For the same reason, do
not spill water or liquid on the product.
16. Servicing—Do not attempt to service the product yourself.
Removing covers can expose you to high voltage and other
dangerous conditions. Request a qualified service person to
perform servicing.
17. Repair—If any of the following conditions occurs, unplug
the power cord from the AC outlet, and request a qualified
service person to perform repairs.
a. When the power cord or plug is damaged.
b. When a liquid was spilled on the product or when
objects have fallen into the product.
c. When the product has been exposed to rain or water.
d. When the product does not operate properly as de-
scribed in the operating instructions.
Do not touch the controls other than those described in
the operating instructions. Improper adjustment of
controls not described in the instructions can cause
damage, which often requires extensive adjustment work
by a qualified technician.
e. When the product has been dropped or damaged.
f. When the product displays an abnormal condition. Any
noticeable abnormality in the product indicates that the
product needs servicing.
18. Replacement parts—In case the product needs replacement parts, make sure that the service person uses
replacement parts specified by the manufacturer, or those
with the same characteristics and performance as the
original parts. Use of unauthorized parts can result in fire,
electric shock and/or other danger.
19. Safety checks—Upon completion of service or repair work,
request the service technician to perform safety checks to
ensure that the product is in proper operating condition.
20. Wall or ceiling mounting—When mounting the product on
a wall or ceiling, be sure to install the product according to
the method recommended by the manufacturer.
21. Heat sources—Keep the product away from heat sources
such as radiators, heaters, stoves and other heat- generating products (including amplifiers).
22. Unplug the power cord from the AC outlet before installing
the speakers.
23. Never expose the screen of the Plasma Display to a strong
impact, for example, by hitting it. The screen may be
broken, resulting in fire or personal injury.
24. Do not expose the Plasma Display to direct sunlight for a
long period of time. The optical characteristics of the front
protection panel changes, resulting in discoloration or
warp.
25. The Plasma Display weighs about 32.8 kg (72.3 lbs.) for the
PRO-505PU and about 26.8 kg (59.1 lbs.) for the PRO435PU. Because it has small depth and is unstable, unpack,
carry, and install the product with one more person at least
and use the handles.
8
En
Safety Precautions
Installation Precautions
Observe the following precautions when installing with any items such as the optional stand.
When using the optional stand, brackets, or equivalent items
• Ask your dealer to perform the installation.
• Be sure to use the supplied bolts.
•For details, see the instruction manual that comes with the optional stand (or equivalent items).
When using other items
• Consult your dealer.
• The following six mounting holes can be used for the installation:
02
English
Rear view
Mounting hole Mounting hole
Median line
Median line
• Be sure to use four or more mounting holes symmetrical to the vertical and horizontal median lines.
• Use M8 screws, which go 12 to 18 mm (0.5 to 0.7 inches) in depth from the mounting surface of the Plasma Display. See the side
view above.
• Be careful not to block the ventilation opening at the rear of the Plasma Display.
• Be sure to install the Plasma Display on a flat surface because it contains glass.
• The screw holes other than the above are to be used only for the specified products. Never use them for mounting non-specified
products.
• Do not mount or remove the Plasma Display to or from the stand, with speakers attached.
Side view
Plasma
Display
Mounting surface
Mounting
bracket (or
equivalent item)
M8 screw
12 to 18 mm
(0.5 to 0.7 inches)
• It is strongly recommended to use the optional PIONEER mounting products.
• PIONEER shall not be liable for any personal injury or product damage that results from the use of mounting items other than the
optional PIONEER products.
9
En
03
Operational Precautions
PIONEER bears no responsibility for any damages arising from
incorrect use of the product by you or other people,
malfunctions when in use, other product related problems, and
use of the product except in cases where the company must be
liable.
Plasma Display protection function
When still images (such as photos and computer images) stay
on the screen for an extended period of time, the screen will be
slightly dimmed. This is because the protection function of the
Plasma Display automatically adjusts the brightness to protect
the screen when detecting still images; so this does not
designate malfunction. The screen is dimmed when a still
image is detected for about three minutes.
Infrared rays
The Plasma Display releases infrared rays because of its
characteristics. Depending on how the Plasma Display is in
use, the remote controls of nearby equipment may be adversely
affected or wireless headphones using infrared rays are
interfered by noise. If this is the case, place that equipment at a
location where its remote control sensor is not affected.
Radio interference
While this product meets the required specifications, it emits a
small amount of noise. If you place such equipment as an AM
radio, personal computer, and VCR close to this product, that
equipment may be interfered. If this happens, place that
equipment far enough from this product.
Fan motor noise
When ambient temperature of the Media Receiver becomes
high, the rotation speed of the cooling fan motor increases.
This may make you feel that the fan motor is noisy at such an
occasion.
The fan motor keeps running until the power cord of the Media
Receiver is removed from a wall outlet.
Do not attach such items as labels and tape to the
product.
• This may result in the discoloration or scratch of the cabinet.
When not using the product for a long period of time
• If you do not use the product for a long period of time, the
functions of the product may be adversely affected. Switch on
and run the product occasionally.
Condensation
• Condensation may take place on the surface or inside of the
product when the product is rapidly moved from a cold place
to a warm place or just after a heater is switched on in winter
morning, for example. When condensation takes place, do
not switch on the product and wait until condensation
disappears. Using the product with condensation may result
in malfunction.
Cleaning the screen
• When cleaning the screen of this product, gently wipe it with
a soft dry cloth; the supplied cleaning cloth or other similar
cloths (e.g., cotton and flannel). If you use a hard cloth or rub
the screen hard, the surface of the screen will be scratched.
• If you clean the surface of the screen with a wet cloth, water
droplets on the surface may enter into the product, resulting
in malfunction.
Cleaning the cabinet
• When cleaning the cabinet of this product, gently wipe it with
a soft dry cloth; the supplied cleaning cloth or other similar
cloths (e.g., cotton and flannel). If you use a hard cloth or rub
the cabinet hard, the surface of the cabinet will be scratched.
• The cabinet of this product is mostly composed of plastic. Do
not use chemicals such as benzine or thinner to clean the
cabinet. Using these chemicals may result in quality deterioration or coating removal.
• Do not expose the product to volatile gas or fluid such as
pesticide. Do not make the product contact with rubber or
vinyl products for a long period of time. The effect of
plasticizer in the plastic may result in quality deterioration or
coating removal.
• If you clean the surface of the cabinet with a wet cloth, water
droplets on the surface may enter into the product, resulting
in malfunction.
Handles at the rear of the Plasma Display
• Do not remove the handles from the rear of the Plasma
Display.
• When moving the Plasma Display, ask another person for
help and use the handles attached to the rear of the Plasma
Display. Do not move the Plasma Display by holding only a
single handle. Use the handles as shown.
• Do not use the handles to hang the product when installing
or carrying the product, for example. Do not use the handles
for the purpose of preventing the product from tilting over.
10
En
Supplied Accessories
04
Plasma Display
Power cord (2 m/6.6 feet)
Bead band × 3
Media Receiver
English
Cleaning cloth Speed clamp × 3
Warranty card
Power cord (2 m/6.6 feet)
AA size battery × 2
(Alkaline battery)
Screw hole cap × 4
• Always use the power cord supplied with the Plasma Display and the
one supplied with the Media Receiver for each respective unit.
VCR controller
(1.8 m/5.9 feet)
Remote control unit System cable (3 m/9.8 feet)
Stand
Operating Instructions
Screw × 4
(for stand)
Instruction guide
11
En
05 Part Names
Plasma Display
Front view
Rear view
(right view)
4
1 button
2 STANDBY indicator
5
6
7
Lights red when the unit is standby mode.
(page 24)
3 POWER ON indicator
Lights green when the Plasma Display is
operating. (page 24)
8
4 Remote control sensor
5STANDBY/ON button
6 INPUT button
7 VOLUME +/– buttons
8 CHANNEL +/– buttons
9 SYSTEM CABLE terminal (BLACK)
10 SYSTEM CABLE terminal (WHITE)
11 SPEAKER (right/left) terminals
12 AC INLET terminal
9
10
Media Receiver
Front view
POWER
1
ON STANDBY
2
REC
TIMER
ACQUISITION
3 4 5
DATA
The terminals have faced downward.
Pull this section to open the door.
PCINPUT 4
COMPONENT VIDEO
B/PBCR/PR
Y
6 7
-
VIDEO VIDEO AUDIO
S
AUDIO
ANALOG RGB
(
)
STEREO
LRC
8 9 10 11
11
12
1 POWER button
2 POWER ON indicator
3 STANDBY indicator
4 REC TIMER indicator
5 DATA ACQUISITION indicator
6 INPUT 4 terminals
(COMPONENT VIDEO: Y, C
B/PB, CR/PR)
7 INPUT 4 terminal (S-VIDEO)
8 INPUT 4 terminal (VIDEO)
9 INPUT 4 terminals (AUDIO)
10 PC INPUT terminal (AUDIO)
11 PC INPUT terminal (ANALOG RGB)
12
En
Rear view
1 2 3 4 5 6 7 9 10 11 13
IN OUT
CONTROL
SERVICE ONLY
ANTENNA B
VCR CONTROL
IN
OUT
MONITOR OUT
S-VIDEO
S-VIDEO
ANTENNA/
CABLE A IN
INPUT 2
VIDEO
VIDEO
INPUT 2
R-AUDIO-L
R-AUDIO-L
Cable
Cable
CARD
CARD
(TS)
VIDEO
S-VIDEO
S400
R-AUDIO-L
R-AUDIO-L
INPUT 1
INPUT 3
INPUT 3
DIGITAL OUT
OPTICAL
INPUT 1
COMPONENT VIDEO
CB/P
B
YYC
B/PB
CR/P
CR/P
R
R
128
INPUT 1 INPUT 3
HDMI
AC IN
BLACK
WHITE
SYSTEM CABLE
05Part Names
English
14
15 16 17 18 19 20 21 22 23
1 CONTROL IN terminal
2 CONTROL OUT terminal
3 VCR CONTROL terminal
4 ANTENNA B IN terminal
5 ANTENNA/CABLE A IN terminal
6 INPUT 2 terminal (VIDEO)
7 INPUT 2 terminals (AUDIO)
8 i.LINK terminals
9 Cable CARD slot
10 INPUT 1 terminals (AUDIO)
11 DIGITAL OUT terminal (OPTICAL)
12 INPUT 1 terminals
(COMPONENT VIDEO: Y, C
B/PB, CR/PR)
13 AC IN terminal
25 2624
14 RS-232C terminal (used for factory setup)
15 ANTENNA B OUT terminal
16 INPUT 2 terminal (S-VIDEO)
17 MONITOR OUT terminal (S-VIDEO)
18 MONITOR OUT terminal (VIDEO)
19 MONITOR OUT terminals (AUDIO)
20 INPUT 1 terminal (VIDEO)
21 INPUT 1 terminal (S-VIDEO)
22 INPUT 3 terminals (AUDIO)
23 INPUT 3 terminals
(COMPONENT VIDEO: Y, C
B/PB, CR/PR)
24 HDMI terminals (INPUT1/INPUT3)
25 SYSTEM CABLE terminal (WHITE)
26 SYSTEM CABLE terminal (BLACK)
13
En
05 Part Names
Remote control unit
Mode switch (with
1 2
3
4
5
6
7
8
9
10
11
12
13
With the mode switch set to TV
1 TV : Turns on the power to the Plasma
Display or places it into standby mode.
2 Transmission confirmation LED
3 INPUT: Selects an input source of the Plasma
Display. (INPUT 1, INPUT 2, INPUT 3, INPUT 4,
PC, i.LINK)
4 •(dot): Enters a dot.
5 CH RETURN: Returns to the previous chan-
nel.
“TV” selected)
14
15
16
17
18
19
20
21
22
23
24
25
26
27
6 CH +/–: Selects the channel.
7 RETURN: Returns to the previous menu
screen.
/ / / : Selects a desired item on the menu
8
screen.
9 DTV INFO: Shows more information on DTV
programs.
10 SPLIT: Switches the screen mode among 2-
screen, picture-in-picture, and single-screen.
11 FREEZE: Freezes a frame from a moving
image. Press again to cancel the function.
12 SWAP: Switches between the two screens
when in the 2-screen or picture-in-picture
mode.
13 SHIFT: Moves the location of the small screen
when in the picture-in-picture mode.
:When pressed, all buttons on the remote
14
control unit will light. The lighting will turn
off if no operations are performed within
about 5 seconds. This button is used for
performing operations in dark places.
15 ANT: Selects the antenna (A, B). See pages 21
and 22 for details.
16 MTS: Selects the MTS/SAP.
17 0 – 9: Selects the channel.
18 CH ENTER: Executes a channel number.
19 VOL
20
+/–: Sets the volume.
MUTING: Mutes the sound.
21 HOME MENU: Displays the menu screen.
22 ENTER: Executes a command.
23 FAVORITE CH (A, B, C, D):
Selects any of the four preset channels. See
page 37 for details to set the FAVORITE CH.
While watching, you can toggle the set channels by pressing A, B, C and D.
24 SCREEN SIZE: Selects the screen size.
25 DISPLAY: Displays the channel information.
26 AV SELECTION: Selects audio and video
settings. (AV mode: STANDARD, DYNAMIC,
MOVIE, GAME, USER. PC mode: STANDARD,
USER.)
27 SLEEP: Sets the sleep timer.
• When using the remote control unit, point it at the Plasma Display.
• See pages 62 to 68 for operating buttons not listed on this page.
14
En
06Preparation
Installing the Plasma Display
Over 50 cm (19 11/16 inches)
Over 10
15
cm (3
/
16
inches )
Using the optional PIONEER stand
For details on installation, refer to the instruction manual
supplied with the stand.
• This product may be used only with model PDK-1012 stand.
Use with other stands may result in instability causing
possible injury.
Using the optional PIONEER speakers
For details on installation, refer to the instruction manual
supplied with the speaker.
Operating Environment
Operating environment temperature and humidity: +0°C to
+40°C (+32°F to +104°F); less than 85% RH (cooling vents not
blocked)
Avoid installing at the following locations:
• Under direct exposure to sunlight
• Under strong artificial light
• In high humidity
•Poorly ventilated
English
Locating
• Avoid direct sunlight. Maintain adequate ventilation.
• The length of the system cable used to connect the Plasma
Display and the Media Receiver is about 3 m (9.8
• Because the Plasma Display is heavy, be sure to have
someone help you when moving it.
• If you place anything on the top of the Media Receiver it will
not receive enough ventilation and will not operate properly.
• Allow enough space around the upper and back parts when
installing to ensure ventilation around the backside.
feet).
15
En
06 Preparation
Installing the Media Receiver
Plasma Display
POWER
ON STANDBY
TIMER
REC
ACQUISITION
DATA
Media Receiver
(vertical installation)
(horizontal installation)
POWER
REC
DATA
ON STANDBY
TIMER
ACQUISITION
System cable (approx. 3 m/9.8
• Do not place a VCR or any other device on the top of the
Media Receiver.
• When installing, allow enough space on the sides and
above the Media Receiver.
• Do not block the side cooling vents or the rear ventilation fan opening of the Media Receiver.
POWER
REC
DATA
ON STANDBY
TIMER
ACQUISITION
feet)
Over 5 cm
(2 inches)
Installing the Media Receiver vertically
You can use the supplied stand to install the Media Receiver
vertically.
1. Insert the stand into the side of the Media
Receiver.
Right side
2. Secure the stand with the supplied screws.
Screws
16
En
Over 5 cm
(2
inches)
Over 5 cm
(2 inches)
POWER
ON STANDBY
TIMER
REC
ACQUISITION
DATA
Over 5 cm
(2 inches)
Over 10 cm
15
/16 inches)
(3
Over 5 cm
(2
inches)
Over 5 cm
(2 inches)
Over 10 cm
15
/16 inches)
(3
3. Remove the shock absorbing pads.
Shock absorbing pad
Keep the shock absorbing pads and screws. They are required
when you place the Media Receiver in the horizontal position.
06Preparation
English
4. Plug the screw holes using the supplied caps.
Remove the separation sheet.
Align with the
hole and attach.
Screw hole cap
• When you have installed the Media Receiver vertically,
be sure to use the supplied stand. If you place the unit
directly on the floor, the cooling vents will be blocked,
resulting in mechanical failure.
17
En
06 Preparation
Connecting the system cable
Connecting the system cable to the Plasma Display
Plasma Display (rear view)
(WHITE)
(BLACK)
Connecting the system cable to the Media Receiver
Media Receiver (rear view)
DIGITAL OUT
INPUT 1
INPUT 3
INPUT 3
OPTICAL
COMPONENT VIDEO
CB/P
B
YYC
B/PB
CR/P
R
CR/P
R
IN OUT
CONTROL
ANTENNA B
SERVICE ONLY
VCR CONTROL
IN
OUT
MONITOR OUT
S-VIDEO INPUT 2
S-VIDEO
ANTENNA/
CABLE A IN
VIDEO
VIDEO
R-AUDIO-L
R-AUDIO-L
Cable
Cable
CARD
CARD
(TS)
VIDEO
S-VIDEO
S400
R-AUDIO-L
R-AUDIO-L
For details on optional PIONEER speaker
installation, refer to the instruction manual
that came with the speaker.
System cable
AC IN
BLACK
INPUT 1 INPUT 3
HDMI
WHITE
SYSTEM CABLE
(BLACK)
(WHITE)
• THESE SPEAKER TERMINALS CAN BE APPLIED WITH HAZARDOUS VOLTAGE WHEN YOU CONNECT OR DIS-
CONNECT THE SPEAKER CABLES. TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT TOUCH
UNINSULATED PARTS BEFORE DISCONNECTING THE POWER CORD.
18
En
06Preparation
Routing cables
Speed clamps and bead bands are supplied for bunching cables. Once properly bunched, follow the steps below to route the
cables.
When the speakers are installed on the sides
Speaker cable Speed clampsCable binders (supplied
with the stand)*
Attaching speed clamps to the main unit
Attach the speed clamps using the 4 holes marked with
below, depending on your routing system.
* Cable binder
Using the cable binders supplied with the stand, put the
speaker and system cables together so that the cables are
invisible from the front. At that time be careful not to apply
any force to the connection sections of the cables.
Attaching and removing speed clamps
Insert [1] into an appropriate hole on the rear of the Plasma
Display and snap [2] into the back of [1] to lock the clamp.
Speed clamps are designed to be difficult to undo once in
place. Please attach them carefully.
Use pliers to twist the clamp 90°, pulling outward. The clamp
may deteriorate over time and become damaged if removed.
(rear view)
Speaker cable
English
2
1
19
En
06 Preparation
Preparing the remote control unit
Inserting batteries
Open the battery cover.
1
Insert the supplied two AA size batteries.
2
• The battery polarities must correspond with the (+) and
(–) indicators in the battery compartment.
Close the battery cover.
3
Allowed operation range of the remote control
unit
Operate the remote control unit while pointing it toward the
remote control sensor located at the bottom right of the front
panel of the Plasma Display. The distance from the remote
control sensor must be within 7 m (23 feet) and the angle
relative to the sensor must be within 30 degrees in the right or
left direction.
30°
7 m (23 feet)
30°
Remote control
sensor
Cautions regarding batteries
• The remote control unit cannot operate the system if the
batteries in the unit are empty. When this happens, replace
the batteries with new ones.
• Do not use manganese batteries. When you replace the
batteries, use alkaline ones.
• Do not mix batteries of different types. Different types of
batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new
batteries can shorten the life of new batteries or cause
chemical leakage in old batteries.
• Do not leave dead batteries in the remote control unit;
chemical leakage will occur. If you find any chemical leakage,
wipe thoroughly with a cloth.
• The batteries supplied with this product may have a shorter
life expectancy due to storage conditions.
• If you will not use the remote control unit for an extended
period of time, remove the batteries from it.
• WHEN DISPOSING OF USED BATTERIES, BE SURE
TO COMPLY WITH GOVERNMENT REGULATIONS
AND ENVIRONMENTAL PROTECTION GUIDELINES
THAT APPLY IN YOUR COUNTRY OR AREA.
Cautions regarding the remote control unit
• Do not expose the remote control unit to shock, liquid, or
high humidity.
• Do not place the remote control unit under direct sunlight;
the unit may deform.
• The remote control unit may not work properly if the remote
sensor window of the Plasma Display is under direct sunlight
or strong lighting. In such case, change the angle of the
lighting or Plasma Display, or operate the remote control unit
closer to the remote sensor window.
• When any obstacle exists between the remote control unit
and the remote control sensor, the remote control unit may
not function.
• As the batteries become empty, the remote control unit can
function within a shorter distance from the remote control
sensor. Replace the batteries with new ones if necessary.
• The Plasma Display emits very weak infrared rays from its
screen. If you place such equipment operated through
infrared remote control as a VCR nearby, that equipment may
not receive commands from its remote control unit properly
or entirely. If this is the case, place that equipment at a
location far enough from the Plasma Display.
• Depending on the installation environment, infrared rays
from the Plasma Display may not allow this system to
properly receive commands from the remote control unit or
may shorten allowable distances between the remote control
unit and the remote control sensor. The strength of infrared
rays emitted from the screen differs, depending on images
displayed on the screen.
20
En
06Preparation
Cable connections for watching digital
and/or conventional TV channels
This system is equipped with two terminals for inputting TV
broadcasting signals: ANTENNA/CABLE A IN and ANTENNA B.
The ANTENNA/CABLE A IN terminal accepts both digital and
conventional TV broadcasting signals while the ANTENNA B
terminal accepts only conventional TV broadcasting signals.
When using a cable TV to watch digital and/or conventional TV
channels, connect to the ANTENNA/CABLE A IN terminal as
shown. In addition, you may connect an antenna to the
ANTENNA B terminal as shown; use an outdoor antenna to
enjoy clearer pictures. If your outdoor uses a 75-ohm coaxial
cable with an F-type connector, plug it into the antenna
terminal at the rear of the Media Receiver.
Connecting VHF/UHF antennas and a Cable
Converter
Media Receiver (rear)
ANTENNA/
CABLE A IN
Cable connections for watching digital
TV channels over air (VHF/UHF)
If using VHF and UHF antennas to watch digital TV channels,
connect the coaxial cables as shown.
Connecting VHF/UHF antennas
VHF antenna
U/V mixer
Splitter
UHF antenna
English
Cable TV
Cable Converter
Media Receiver (rear)
Splitter
ANTENNA B
IN
OUT
ANTENNA B
IN
ANTENNA/
CABLE A IN
Media Receiver
(rear)
OUT
• Be sure to connect coaxial cables as shown above. Signal reception
may fail if not properly connected.
• Be sure to connect coaxial cables as shown above. Signal reception
may fail if not properly connected.
21
En
06 Preparation
H
Switching between antenna A and B
To watch broadcasts via the two antennas, you can select it by
pressing ANT on the remote control unit.
• While watching a broadcast, press ANT to view the image
received from the other antenna.
•Pressing ANT while watching in the 2-screen mode (TV
image and video image) with TV selected will display the TV
image of the other antenna.
•Pressing ANT while watching in the 2-screen mode with two
TV images displayed will not have any effect.
•Pressing ANT while watching in the 2-screen mode with two
video images displayed will switch the selected screen to a
TV image.
Inserting the cable card
The Media Receiver is equipped with a slot for inserting a cable
card. When you are watching digital and/or High Definition TV
channels over cable, the card allows you to use the POD
service provided by the cable TV company; the POD stands for
Point of Deployment. This service presents various types of
useful information, using HTML text.
Confirm that the ANTENNA/CABLE A IN terminal has
1
been connected with the coaxial cable from the Cable
Converter. See page 21.
Hold the tab of the slot cover on the rear of the Media
2
Receiver, and remove the cover while releasing the tab’s
latch.
Insert the specified cable card into the Cable CARD slot
3
as far as it goes.
DIGITAL OUT
OPTICAL
ANTENNA/
CABLE A IN
PUT 2
VIDEO
DEO
R-AUDIO-L
R-AUDIO-L
Cable
CARD
(TS)
VIDEO
S-VIDEO
S400
R-AUDIO-L
R-AUDIO-L
INPUT 3
COMPONENT VIDEO
Y
Y
• Be sure to insert only the specified cable card.
• Do not insert a PCMCIA card.
R
/P
R
C
B
/P
B
C
R
/P
R
C
B
/P
B
C
INPUT 1
Cable
CARD
UDIO-L
(TS)
VIDEO
S400
R-AUDIO-L
INPUT 1
Tab
DIGITAL OUT
OPTICAL
B
COMPONENT VIDEO
/P
B
C
Y
R
/P
R
C
INPUT 1
R
P
22
En
06Preparation
Connecting the power cord
Connect the power cord after all component connections have been completed.
Plasma Display (rear view)
Noise filter
Partially eliminates noise
caused by the power source.
English
Power cord
Media Receiver (rear view)
DIGITAL OUT
IN OUT
CONTROL
SERVICE ONLY
ANTENNA B
MONITOR OUT
VCR CONTROL
IN
OUT
ANTENNA/
Cable
Cable
CARD
CABLE A IN
CARD
INPUT 2
S-VIDEO
INPUT 2
VIDEO
R-AUDIO-L
R-AUDIO-L
VIDEO
S-VIDEO
• Use only the supplied power cord.
• Be sure to use the specified power supply voltage;
neglecting this can result in fire or electric shock.
•For the Plasma Display System, a three-core power cord
with a ground terminal is used for efficiency protection.
Always connect the power cord to a three-pronged
outlet and make sure that the cord is properly grounded.
OPTICAL
S400
(TS)
INPUT 1
COMPONENT VIDEO
VIDEO
R-AUDIO-L
CB/PB
CR/PR
INPUT 1 INPUT 3
R-AUDIO-L
INPUT 3
S-VIDEO
INPUT 3
INPUT 3
HDMI
YYC
B/PB
CR/PR
AC INLET
AC IN
BLACK
WHITE
SYSTEM CABLE
AC IN
Noise filter
Partially eliminates noise
caused by the power source.
Power cord
• Always turn off the power of the Plasma Display and Media Receiver
when connecting the power cords.
• Disconnect the power cord from the power outlet when the Plasma
Display System is not going to be used for a long period of time.
23
En
07 Basic Operations
Turning on the power (Standby)
1
Press on the Plasma Display if the STANDBY indicator
is off.
• The STANDBY indicator on the Plasma Display lights
up red.
Confirm that the STANDBY indicators light up red, and
2
then press TV
on the remote control unit or
STANDBY/ON on the Plasma Display or POWER on the
Media Receiver to turn the system on.
• The POWER ON indicators on the Plasma Display and
Media Receiver light up green.
• In this manual, “system” means the Plasma Display Panel and Media
Receiver.
Turning off the power (Standby)
1
Press TV on the remote control unit or STANDBY/ON
on the Plasma Display or POWER on the Media Receiver.
• The system enters the standby mode and the image on
the screen disappears.
• Both STANDBY indicators light up red.
• It is recommended to place the system into the standby
mode by pressing TV
This allows the system to automatically receive digital
TV program information in the standby mode.
on the remote control unit.
Plasma Display
STANDBY indicator
POWER ON indicator
button
(right view)
STANDBY/
ON button
Media Receiver
• If you are not going to use this system for a long period of time, press
on the Plasma Display and remove the power cord from the power
outlet.
Plasma Display/Media Receiver status indicators
Indicator Status System Status
Plasma Display Media Receiver
POWER ON STANDBY POWER ON STANDBY
Power to the Plasma Display and Media Receiver is off. Or the power cords
have been disconnected.
Power to the system is on.
The system is in the standby mode.
The power cord has been disconnected from the Media Receiver.
Flashing
Power to the Plasma Display is off. Or the power cord has been disconnected
Flashing
from the Plasma Display.
POWER
ON STANDBY
REC
TIMER
POWER ON indicator
POWER button
DATA
ACQUISITION
STANDBY indicator
For other than the above, see “Troubleshooting” on page 69.
24
En
07Basic Operations
Watching TV channels
Unless you set up TV channels that you can watch under the
current conditions, you cannot tune in those channels. For the
procedure, see “Setting up TV channels” on page 31.
• When watching a digital TV program, you may see emergency alert
messages scrolling at the top of the screen. Those messages are
broadcasted by TV stations as necessary when in emergency
situations.
Selecting the antenna
After confirming that the Mode switch on the remote control
unit has been set to “TV”, press ANT on the remote control unit
to select antenna A or B.
• Make this selection depending on the connections to the
antenna input terminals on the Media Receiver (page 21).
Changing channels
To increase the channel number, press CH + on the remote
control unit. To decrease the channel number, press CH –.
• CHANNEL +/– on the Plasma Display operates the same as
CH +/– on the remote control unit.
•Press CH RETURN to switch the currently tuned channel to
the previously tuned channel.
Press CH RETURN again to restore the currently tuned
channel.
CHANNEL +/–
Plasma Display
(right view)
English
Using 0 – 9 and • (dot) on the remote control unit
Select channels directly by pressing buttons 0 to 9. To select
subchannels, also use the • (dot) button.
EXAMPLE
•To select channel 5 (1-digit channel), press 5.
•To select channel 25 (2-digit channel), press 2 then 5.
•To select channel 125 (3-digit channel), press 1, 2, then 5.
•To select subchannel 10.01, press 1, 0, • (dot), 0, then 1.
•To select subchannel 10.001 (for the cable TV), press 1, 0,
• (dot), 0, 0, then 1.
•After entering a channel or subchannel number, you may press
CH ENTER to tune in the channel more quickly.
• Each time you change a channel, such a channel banner appears
that shows information about the currently selected channel. To clear
the channel banner, press DTV INFO. For more information about
the channel banner, see “Viewing a channel banner” on page 26.
Channel banner
12:33pm
DTV 2 • 1002.102 A
XXXXXXXXXX
12:30pm — 2:00pm
25
En
Loading...