Pioneer PRO-111FD, PRO-151FD Operating Instruction

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT

D3-4-2-1-1_En-A

Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

10)

Only use attachments/accessories specified by the manufacturer. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

Unplug this apparatus during lightning storms or when unused for long periods of time. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

P1-4-2-2_En

11)

12)

13)

14)

IMPORTANT NOTICE – THE SERIAL NUMBER FOR THIS EQUIPMENT IS LOCATED IN THE REAR. PLEASE

WRITE THIS SERIAL NUMBER ON YOUR ENCLOSED WARRANTY CARD AND KEEP IN A SECURE AREA. THIS IS FOR YOUR SECURITY.

WARNING: Handling the cord on this product or cords associated with accessories sold with the product will expose you to chemicals listed on proposition 65 known to the State of California and other governmental entities to cause cancer and birth defect or other reproductive harm.

Wash hands after handling

D36-P4-A_En

D1-4-2-6-1_En

TABLE OF CONTENTS

Congratulations on your purchase of a Pioneer KURO flat panel television.

KURO is the future of Pioneer flat-panel displays. It’s a world without boundaries. A place where the senses evolve, colors are felt and sounds can be tasted. An experience that changes not only the way you look at television, but the way you look at the world.

We are proud to incorporate this philosophy of exceptional quality, state-of-the-art design and meticulous engineering to make the KURO undeniably unique and bring you one of the best entertainment experiences possible.

Please take some time to read through this owner’s guide and manual to learn about the many features and benefits that set the KURO apart. We hope you enjoy the experience of owning the KURO and invite you to enter a new world of seeing and hearing like never before.

TABLE OF CONTENTS

1 Introduction to the ELITE Series Flat Panel TVs .....................................................................................6

1.1 Flat Panel TV Shipment Checklist ...................................................................................................................................6

1.2 Control Options: Get to Know Your Flat Panel TV .......................................................................................................... 8

1.2.1 Control Buttons and More on the Flat Panel TV .................................................................................................... 8

1.2.2 Operating the Remote Control.............................................................................................................................. 10

1.2.3 Buttons on the Remote Control ............................................................................................................................ 12

2 Install Your Flat Panel TV ......................................................................................................................14

2.1 Choose a Location and the Mounting Method............................................................................................................. 14

2.1.1 Check the Location for Suitability ......................................................................................................................... 15

2.1.2 Lift and/or Move Your Panel (the How To’s)......................................................................................................... 15

2.2 Install the Panel Using a Stand ..................................................................................................................................... 16

2.2.1 Use or Remove the Included Stand ...................................................................................................................... 16

2.2.2 Connect the Speaker Cables ................................................................................................................................. 22

2.3 Wall/Ceiling Mounting.................................................................................................................................................... 23

2.4 Mount the Flat Panel TV .................................................................................................................................................24

2.5 Attach the Color Sensor ................................................................................................................................................. 26

2.6 Connect to Broadcast TV & Other Devices (DVR, Receiver, BDR, etc.) ..................................................................... 29

2.6.1 Add Analog (conventional) and Digital TV Channels ..........................................................................................29

2.6.2 Connect Your Other Pioneer Equipment.............................................................................................................. 29

2.6.3 Connect the Power Cord to the Panel .................................................................................................................. 32

2.7 Route then Bundle the Power Cord and Cables .......................................................................................................... 32

3 Basic Operations For Television Viewing .............................................................................................34

3.1 Turn the Flat Panel TV ON/OFF...................................................................................................................................... 34

3.2 Program the Flat Panel TV for Television Viewing........................................................................................................ 35

3.2.1 Choose Analog or Digital TV Channels ................................................................................................................ 35

3.2.2 Explore the Home Menu ........................................................................................................................................ 35

3.2.3 Assign a Language................................................................................................................................................. 37

3.2.4 Set the Clock........................................................................................................................................................... 38

3.2.5 Create the List of Channels ................................................................................................................................... 38

3.2.6 Skip or Delete Unwanted Channels...................................................................................................................... 41

3.2.7 Channel List ............................................................................................................................................................ 42

3.3 Quick Start for Watching Television.............................................................................................................................. 44

3.3.1 Change the Channel/Sub-Channel....................................................................................................................... 44

3.3.2 Adjust the Volume/Sound...................................................................................................................................... 44

3.3.3 Turn On the Sleep Timer........................................................................................................................................ 44

3.4 Adjust the Picture and Sound Quality .......................................................................................................................... 45

3.4.1 Adjust the Picture for Your Room Lighting .......................................................................................................... 45

3.4.2 General Picture (Video) Adjustment for an AV Source .......................................................................................46

3.4.3 Compare Images When Adjusting the Picture....................................................................................................47

3.4.4 Display a Graphical Picture/Sound Adjustment Screen..................................................................................... 48

3.4.5 Sound Control......................................................................................................................................................... 49

3.4.6 General Sound (Audio) Adjustment...................................................................................................................... 49

3.5 Block Programs, Channels, or Content ........................................................................................................................ 50

3.5.1 Assign a Parental Control (Block) Password....................................................................................................... 50

TABLE OF CONTENTS

3.5.2 Activate Parental Control .......................................................................................................................................51

3.5.3 Assign a Rating System to Create Blocks ............................................................................................................51

3.5.4 Temporarily Remove a Block .................................................................................................................................54

3.6 Smart Starts for New Owners ........................................................................................................................................55

3.6.1 Use the TOOLS Menu.............................................................................................................................................55

3.6.2 Extend Your Panel Life............................................................................................................................................55

3.6.3 Turn On the Image Orbiter.....................................................................................................................................56

3.6.4 Trigger the Screen-Saving Video Pattern Periodically.........................................................................................56

3.6.5 Activate Energy Save to Reduce Power Usage ....................................................................................................56

4 Additional Picture and Sound Adjustment Options ........................................................................... 57

4.1 Choose an AV Option (Video, Game, etc.).....................................................................................................................57

4.1.1 AV Source through the Remote Control...............................................................................................................57

4.1.2 Choose an AV Source through the Home Menu .................................................................................................58

4.1.3 Choose a PC Source...............................................................................................................................................58

4.1.4 Set the Panel to Recognize a Game Console .......................................................................................................59

4.2 Adjust Specific Picture Elements ..................................................................................................................................59

4.2.1 Choose a Screen Size (Automatically or Manually).............................................................................................59

4.2.2 Correct the Picture for an AV or PC Source .........................................................................................................61

4.3 Assign Advanced Picture Functions .............................................................................................................................62

4.3.1 Adjust for Screen Masking (black bars on sides) ................................................................................................62

4.3.2 Select a PureCinema Level for High Quality Image.............................................................................................63

4.3.3 Select an Intelligent Mode Option.........................................................................................................................64

4.3.4 Select the Picture Detail Options ..........................................................................................................................64

4.3.5 Adjust the Color Temperature ...............................................................................................................................65

4.3.6 Use CTI and Color Space .......................................................................................................................................66

4.3.7 Use the Color Management...................................................................................................................................66

4.3.8 Reduce Noise from the Image...............................................................................................................................67

4.3.9 Adjust Color Signals...............................................................................................................................................68

4.4 View in Multi-Screen .......................................................................................................................................................69

4.4.1 Split/Swap/Shift the Screen...................................................................................................................................69

4.5 Freeze the Picture ...........................................................................................................................................................70

4.6 Use the Banner Feature..................................................................................................................................................71

4.7 Select Alternatives for/to Sound ....................................................................................................................................72

4.7.1 Activate Closed Captioning (CC) ...........................................................................................................................72

4.7.2 Switch Languages Using MTS...............................................................................................................................74

4.7.3 Select SAP...............................................................................................................................................................74

4.7.4 Apply Sound Effect Settings ..................................................................................................................................75

4.7.5 Use Auto Volume Control (AVC)............................................................................................................................75

4.8 Manage the Power ..........................................................................................................................................................76

5 Use Other Equipment With Your Flat Panel TV ................................................................................... 78

5.1 Program the Remote Control to Operate Other Equipment........................................................................................78

5.1.1 Use the Learning Feature.......................................................................................................................................78

5.1.2 Assign a Manufacturing Code to the Remote Control ........................................................................................79

5.1.3 Issue a Library Search for a Manufacturer Code.................................................................................................79

5.1.4 Clear Added Manufacturer Codes from the Remote Control .............................................................................80

5.1.5 Control a Pioneer Receiver ....................................................................................................................................80

5.1.6 Control a Cable (CBL) or Satellite (SAT) System..................................................................................................81

5.1.7 Control a Video Cassette Recorder (VCR) ............................................................................................................82

5.1.8 Control a DVD Player/DVR Recorder/BD Player..................................................................................................83

5.2 Use HDMI Inputs.............................................................................................................................................................84

5.2.1 Specify the HDMI Input Type .................................................................................................................................84

5.2.2 Specify a Digital HDMI Signal Type ......................................................................................................................85

5.2.3 Specify an Audio HDMI Signal Type .....................................................................................................................85

5.3 Control Equipment with the Panel’s Remote Through HDMI .....................................................................................86

5.3.1 Control an AV System.............................................................................................................................................88

5.3.2 Control a Recorder .................................................................................................................................................89

5.3.3 Control a Player.......................................................................................................................................................89

5.3.4 Add an AV Amp or a BD Player.............................................................................................................................90

5.4 Specific HDMI Control Commands ...............................................................................................................................91

5.4.1 Play Source Sound Using an HDMI Command...................................................................................................91

TABLE OF CONTENTS

5.4.2 Turn OFF the Power With an HDMI Command ................................................................................................... 91

5.4.3 Turn ON the Power With an HDMI Command .................................................................................................... 91

5.4.4 Test the Power Control (On/Off)............................................................................................................................ 92

5.5 Connect a Game Console or Camcorder ...................................................................................................................... 92

5.6 Use the IR REPEATER OUT............................................................................................................................................ 92

5.7 Operate the Home Media Gallery .................................................................................................................................. 93

5.7.1 Network Connections............................................................................................................................................. 94

5.7.2 Connect a USB Device........................................................................................................................................... 96

5.8 Run the Home Media Gallery......................................................................................................................................... 98

5.8.1 Show Your Movie Files on the Flat Panel TV ...................................................................................................... 101

5.8.2 Play Your Music Files on the Flat Panel TV ........................................................................................................ 103

5.8.3 Show Your Photo File on the Flat Panel TV ........................................................................................................ 104

5.9 Use the TOOLS Menu ................................................................................................................................................... 106

5.10 HMG Setup .................................................................................................................................................................. 118

5.11 Other useful functions................................................................................................................................................ 119

5.12 Add Other Audio Equipment...................................................................................................................................... 121

5.13 Add a Computer (PC) ................................................................................................................................................. 122

5.13.1 Automatic Image Position and Clock Adjustments ........................................................................................122

5.13.2 Manual Image Position and Clock Adjustments .............................................................................................122

6 Helpful Information .............................................................................................................................123

6.1 Frequently Asked Questions (FAQs) ........................................................................................................................... 123

6.2 Check Your Software/Hardware Version..................................................................................................................... 124

6.3 Cleaning Methods......................................................................................................................................................... 124

6.4 Troubleshooting & Service Information....................................................................................................................... 125

6.4.1 Check the Signal Strength................................................................................................................................... 130

7 Cautions and Warnings........................................................................................................................131

7.1 Installation Details........................................................................................................................................................ 131

7.2 Physical Location & Temperature Considerations..................................................................................................... 131

7.3 Usage Guidelines .......................................................................................................................................................... 131

7.4 Signal Interference or Noise ........................................................................................................................................ 132

7.5 Phosphor Properties..................................................................................................................................................... 132

7.6 Image Information Including Retention & After-Image Lag ......................................................................................132

7.7 Safety Precautions........................................................................................................................................................ 134

7.8 Legal Notices................................................................................................................................................................. 134

7.8.1 Safety..................................................................................................................................................................... 134

7.8.2 Radio Interference................................................................................................................................................135

8 Appendix ..............................................................................................................................................136

8.1 Ratings Charts (for Various Audience Classifications) ............................................................................................. 136

8.1.1 TV Ratings (age-based) ........................................................................................................................................ 136

8.1.2 U.S. TV Parental Guideline Ratings (age/category-based)................................................................................136

8.1.3 MPAA Movie Ratings (age-based)...................................................................................................................... 136

8.1.4 Canadian - English Ratings (age-based) ............................................................................................................ 137

8.1.5 Canadian - French Ratings (age-based)............................................................................................................. 137

8.2 Manufacturer Codes to Program into the Remote Control....................................................................................... 138

8.2.1 Cable...................................................................................................................................................................... 138

8.2.2 Satellite.................................................................................................................................................................. 138

8.2.3 VCR (Brands A - F)................................................................................................................................................139

8.2.4 VCR (Brands G - O)............................................................................................................................................... 140

8.2.5 VCR (Brands P - V) ............................................................................................................................................... 141

8.2.6 VCR (Brands W - Z) .............................................................................................................................................. 141

8.2.7 PVR ........................................................................................................................................................................ 142

8.2.8 BD (HD-DVD)........................................................................................................................................................ 142

8.2.9 DVD-R.................................................................................................................................................................... 142

8.2.10 DVD (Brands A - N) ............................................................................................................................................ 143

8.2.11 DVD (Brands O - Z)............................................................................................................................................. 144

8.2.12 LD......................................................................................................................................................................... 144

8.3 Specifications................................................................................................................................................................ 145

8.4 Glossary ......................................................................................................................................................................... 162

8.5 Index............................................................................................................................................................................... 164

8.6 Trademarks, Licenses, & Patent Information ............................................................................................................. 165

Bracket (for 50”)

Bracket (for 60”)

Introduction to the ELITE Series Flat Panel TVs

1 Introduction to the ELITE Series Flat Panel

TVs

The Pioneer ELITE Series Flat Panel TV models include the 60-inch PRO-151FD and the 50-inch PRO-111FD (screen sizes measured diagonally). Below is a list of all accessories shipped with your panel. If an item is missing, please contact your dealer or our Service organization immediately. Service contact information is listed on the back of this manual.

1.1 Flat Panel TV Shipment Checklist

In addition to the flat panel TV, there are several accessories included to make installation quick and easy. Please check for contents before discarding or allowing your installer to discard any packing material.

The PRO-151FD and PRO-111FD shipments have slightly different pieces. Identify the accessories from the appropriate list below.

You will need a Philips screwdriver when mounting the speaker and attaching the stand.

Shipped with both models

Remote Control Batteries for Remote (2) Cleaning Cloth

Power Cord (2 m/6.6 feet) Cable Clamps (4) Operating Instructions

Color Sensor Screws (x 2) (M5 x 8 mm) Warranty Card

Color Sensor Bracket (when attached to the top right of the rear panel)

Also shipped with the PRO-151FD (60” panel)

Stand kit

Base Cover Stand Pipes (2)

Introduction to the ELITE Series Flat Panel TVs

for BOTTOM-Right

for TOP-Right

for TOP-Left

for BOTTOM-Left

for BOTTOM-Right

for TOP-Right

for TOP-Left

for BOTTOM-Left

Also shipped with the PRO-151FD (60” panel)

Silver Screws (4) (4×10 mm)

Falling Prevention Metal Fittings (2)

Black Screws (4) (M6×20 mm)

Light-Blocking Shield Screws to Metal Fittings (4) (M4×35 mm)

Speaker accessories

Speaker Cables (2)

Speaker Mounting Screws (16) (M5×10 mm)

Speaker

Speaker Brackets

Also shipped with the PRO-111FD (50” panel)

Stand kit

Falling Prevention Metal Fittings (2)

Screws to Metal Fittings(2) (M4×35 mm)

Speaker accessories

Speaker Cables (2) Speaker Brackets

Speaker Mounting Screws (16)

(M5×10 mm)

Speaker

(PRO-111FD)

(PRO-151FD)

Introduction to the ELITE Series Flat Panel TVs

1.2 Control Options: Get to Know Your Flat Panel TV

You can operate your flat panel TV from the panel buttons or with the remote control. The following sections provide button locations/operations for the panel and the remote control.

1.2.1 Control Buttons and More on the Flat Panel TV

Your flat panel TV has buttons, indicators, and sensors on the lower front bezel with more buttons, toggles, and ports on the panel sides. Refer to the drawings below for specific locations and functions. Or, for the back ports and terminals only, check the terminal position sheet located near the panel’s terminal compartment to identify the various options.

ELITE Series Models: Face of Panel

1 3 4 5 72 1 32

1 -Power ON indicator 2 -STANDBY indicator 3 -SLEEP indicator

Command Side of the Panel (left side)

4 -Room Light sensor 5 -Remote Control sensor 6 -Color Sensor 7 -Bezel (some call it the front frame)

8 -USB terminal

9 -INPUT 7 terminal (HDMI) 10 -PHONES terminal 11 -INPUT 3 terminal (Video) 12 -INPUT 3 terminals (Audio) 13 -STANDBY/ON button 14 -INPUT button 15 -VOLUME Up/Down buttons 16 -CHANNEL Up/Down buttons

Introduction to the ELITE Series Flat Panel TVs

1 2 43

(upper bank)

(middle bank)

(PRO-151FD)

(lower bank)

Back of the Panel

1 -ANT terminal 2 -PC Input terminal (Analog RGB) 3 -Color sensor terminal 4 -AC In terminal

13125 14 1516171819 2120 2223

7 8 9

5 -Ethernet cable port 6 -INPUT 4 terminal (HDMI) 7 -INPUT 5 terminal (HDMI) 8 -INPUT 6 terminal (HDMI) 9 -RC-232C terminal (for factory use) 10 - INPUT 4 terminals (Audio) 11 -INPUT 5 terminals (Audio) 12 -SUB WOOFER OUT terminal 13 -AUDIO OUT terminals (Audio) 14 -INPUT 1 terminal (S-Video)

10 11 246

15 -INPUT 1 terminal (Video) 16 -INPUT 1 terminals (Audio) 17 -INPUT 2 terminal (Video) 18 -INPUT 2 terminals (Audio) 19 -INPUT 2 terminals (Component, Y, P 20 -IR REPEATER OUT terminal 21 -PC INPUT terminal (Audio) 22 -CONTROL OUT terminal 23 -DIGITAL OUT terminal (Optical) 24 -SPEAKERS (right/left) terminal

25 282726

25 -Speakers (R) terminal (speaker side) 26 -Color Sensor

Terminals on side and rear panels are common to both ELITE models.

27 -Power On button 28 -Speakers (L) terminal (speaker side)

, PR)

When disposing of used batteries, please comply with governmental regulations or environmental public institution’s rules that apply in your country/area.

Introduction to the ELITE Series Flat Panel TVs

1.2.2 Operating the Remote Control

The remote control for the ELITE Series panels is a powerful tool. This section provides a brief introduction to your remote control while later sections explore more advanced operations.

Insert the Batteries into the Remote Control

To open push and slide the battery cover in the direction of the arrows. Load the supplied two AA size batteries by the negative polarity (–) ends first.

The batteries supplied with this product may have a shorter life expectancy due to storage conditions. If the remote control seems to be failing or is weak, replace the provided batteries with new alkaline batteries.

Never mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical leaks in old batteries. Also, mixing different types or brands of batteries can cause issues as batteries brands have slightly different characteristics.

Note: If the flat panel TV’s remote control is not needed for an extended length of time, remove the batteries.

Remote Control Issues

There are several issues that can affect your remote control but the most common problem is weak batteries. Weak batteries in the remote control can cause communication to fail or only operate sporadically. In this situation, try moving closer to the panel and attempt to control the panel with the remote. If the panel responds then change the batteries. If moving closer has no effect on the panel, check the surroundings for objects that might be blocking the signal. Also consider other equipment with remote controls that are in the area around the panel. Objects and other IR signals can disrupt the remote. For more help with your remote control, refer to “6.1 Frequently Asked Questions (FAQs).”

Introduction to the ELITE Series Flat Panel TVs

30º

Sensor

30º

7 m

(23 feet)

Operating Range for the Remote Control

To control the flat panel TV, point the remote towards the sensor on the panel’s bottom right corner. For easy operation, keep the distance between the remote control and the sensor less than 7 m (23 feet) and at an angle of less than 30 degrees.

The remote control may not work properly if the sensor is in direct sunlight or very bright lighting. If your viewing room is naturally bright, change the position of the panel or physically use the remote control closer to the panel’s sensor.

Note: If the remote control is left sitting in direct sunlight or under a very strong light, the case could warp or

deform.

Introduction to the ELITE Series Flat Panel TVs

1.2.3 Buttons on the Remote Control

Except for a few options, commands available through the buttons on the flat panel TV are duplicated on the remote control. The remote control can be programmed to control other equipment such as a DVD Player, Surround Sound system, etc. A later section entitled “5 Use Other Equipment With Your Flat Panel TV” explains how to use the remote to control other equipment.

This section identifies and describes the buttons on the remote control.

Remote: Left side buttons

Select a source (INPUT 1 thru INPUT 7)

Select the PC terminal as an input source

AV Source: OPTIMUM, PERFORMANCE, MOVIE,

Cycle view thru single-screen, 2-screen,

Freeze a frame from a moving image then

press again to cancel the freeze function

Enter a dot for selecting a sub-channel

Exit the menu to return to the normal screen

Color buttons (Red, Green, Blue, Yellow):

Control a BD player for HDMI Control functions only

(top to bottom, left to right)

TV :

Turn On or place panel in Standby

INPUT:

AV SELECTION:

Select audio/video settings

PURE, GAME, SPORT, Standard

PC Source: STANDARD, USER

SPLIT:

picture-in-picture

FREEZE:

Number buttons 0 thru 9:

Select a channel

•(dot):

VOL +/–:

Set the volume

EXIT:

Arrow buttons:

Navigate the menu screens

HOME MENU:

Display the HOME MENU

HDMI CONTROL:

Select the HDMI Control functions

PC:

SPLIT

EXIT

DVD

TOP MENU

HOME MENU

SAT / DVD MENU

INPUT

DISPLAY

SWAP

TV/DTV

SCREEN

SIZE

SHIFT

6 7

SELECTION

FREEZE

123

456

789

VOL

SAT GUIDE

CH RETURN

MUTING

ENTER

TOOLS

ENTER

RETURN

HDMI

CTRL

SOURCE

SELECT

RECEIVER

INPUT

CBL

RCV VCRSAT

STOP

VOL

DVD

DVR

REC

HMG

EDIT/LEARN

SELECT:

Select for TV/RCV, CBL/SAT, VCR, or DVD/DVR

Introduction to the ELITE Series Flat Panel TVs

Remote: Right side buttons

INPUT

SPLIT

6 7

SELECTION

FREEZE

TV/DTV

SCREEN

DISPLAY

SIZE

18 19

SWAP

SHIFT

20 21

123

456

789

ENTER

CH RETURN

VOL

MUTING

EXIT

DVD

TOP MENU

SAT GUIDE

TOOLS

(top to bottom, left to right)

16 : Lights up all buttons

Lights turn off if no operations are performed within five seconds. This is used for remote control use in dark locations.

17 TV/DTV:

Select analog or digital TV channels

18 DISPLAY:

Display the channel information

19 SCREEN SIZE:

Select the screen size

20 SWAP:

Switch between the two screens when viewing as 2-screen or picture-in-picture

21 SHIFT:

Move the location of the small screen when viewing as picture-in-picture

22 CH ENTER:

Change the channel

23 CH RETURN:

Return to the previous channel

24 MUTING:

Turn off the sound while the video continues to play

HOME MENU

SAT / DVD MENU

HDMI

CTRL

SOURCE

SELECT

RECEIVER

INPUT

CBL

RCV VCRSAT

ENTER

STOP

VOL

DVD

DVR

RETURN

REC

HMG

EDIT/LEARN

25 CH +/–:

Cycle through channels

26 TOOLS:

Display the TOOLS Menu - refer to “3.6 Smart Starts for New Owners”

27 ENTER:

Execute a command

28 RETURN:

Return to the previous menu screen

29 Player/Recorder Control:

Use buttons for control of connected equipment

30 HMG (Home Media Gallery):

Display the Home Media Gallery menu Use this button to start recording (for VCR/DVD recorder only)

Rear view (PRO-151FD)

Side view

Mounting surface

Mounting bracket (or equivalent item)

M8 screw

12 mm to 18 mm (0.5 inches to

0.7 inches)

Rear view (PRO-111FD)

Mounting hole

Install Your Flat Panel TV

2 Install Your Flat Panel TV

There are several installation options for your flat panel TV. This chapter walks you through how to choose an installation site, the best mounting methods, and how to install your panel.

2.1 Choose a Location and the Mounting Method

Your flat panel TV is very thin. The panel needs a solid surface and some sort of support structure (a stand, table, etc.) to protect it from being tipped over or knocked down. Use installation accessories and parts included with the shipment. Pioneer recommends working with a qualified installer whenever possible.

Regardless of the mounting method, anchor or secure your flat panel TV using a combination of the mounting holes and/or supplied bolts.

Note: Some installation options require a different type of bolt. Check with your installer or dealer to purchase the

T W

appropriate bolt(s).

T W

Install Your Flat Panel TV

Over 10 cm (3 15/16 inches)

Over 50 cm (19 11/16 inches)

The distance behind and above the panel

changes depending on your choice of mount.

Consult with your dealer or professional

installer for proper ventilation.

Use the handles to move the panel.

Do not move the panel by holding the

color sensor, speaker or speaker

brackets.

2.1.1 Check the Location for Suitability

When choosing the location for your panel, there are several factors you need to keep in mind. The installation site should be out of direct sunlight and have sufficient ventilation around the flat panel TV to allow cooling. The diagram below is an example of a stand-mounted panel with proper ventilation.

Use the checklist below to judge possible installation sites.

Sufficient ventilation No danger of power overloads Safe from excessive vibrations Separate from other IR equipment Away from air conditioners Protected from hits or shocks Free of moisture or dampness Distance from heat sources No danger of splashing water Out of direct sunlight Route cords and cables safely Away from strong lighting sources

For specific cautions and safety information, refer to “7.2 Physical Location & Temperature Considerations” and “7.7 Safety Precautions.”

2.1.2 Lift and/or Move Your Panel (the How To’s)

This flat panel TV is built for endurance but because of the technology, the panel must be handled with care. Use the handles attached to the rear of the flat panel TV to lift the unit. To avoid flexing or twisting the unit, you need at least two people to lift and move the panel. Do not move the flat panel TV by holding only a single handle or by dragging the panel by its handles.

Note: Do not use the handles to hang the flat panel TV or as anchors to prevent the panel from slipping or tipping

after it is mounted.

(PRO-111FD)

Do not handle the flat panel TV on a wagon or pallet that is smaller than its stand. The stand will bend.

Screws (4 x 10 mm: silver)

Completed stand

Sheet

Screws (4 x 10 mm: silver)

Front

Rear

Base cover

Install Your Flat Panel TV

2.2 Install the Panel Using a Stand

2.2.1 Use or Remove the Included Stand

The PRO-111FD ships with the Pioneer table top stand (stand) attached. Attach the included stand to the panel for the PRO-151FD. For PRO-111FD, attach the falling prevention metal fittings after placing the panel to stand upright.

Installation screws (M4 × 35 mm: black)

Falling prevention metal fitting

Attach the Stand to the Panel

1 ) Detach the speaker if it has already been added.

Refer to “Attach/Detach the Speaker” on page 19 for assistance.

2 ) Lay the flat panel TV down on a raised surface with the stand base hanging over the edge. 3 ) Place all stand parts on a soft cloth to avoid scratching.

If you are mounting the PRO-151FD continue with Steps 4 and 5. If you are mounting the PRO-111FD skip to Step 7.

4 ) Turn the base cover over so that the bottom is facing up. 5 ) Insert the stand supports (legs) into the base cover.

Please carefully install the supports (left and right) so that they are in the correct positions. Misaligned supports can damage the base and/or the supports.

6 ) Tighten the base screws to lock the supports in to place.

Note: Assemble the stand with a soft sheet placed under the base cover. If a sheet is not laid before assembly,

the front surface of the base cover may be scratched.

Install Your Flat Panel TV

Installation screws (M4 x 35 mm: black)

(PRO-151FD)

Falling prevention metal fitting

Line up the column supports with the bottom of the flat panel TV.

Insert the stand supports into the flat panel

TV so that the arrow marked “FRONT/FACE

AVANT” on the bottom of the stand

points down.

Installation bolts (M6 x 20 mm)

7 ) After assembling the stand, attach the falling prevention metal fittings using the installation screws.

8 ) With the flat panel TV still face down, insert the stand’s supports into the bottom of the panel then tighten

the screws.

9 ) With the assistance of at least one other person, lift the panel upright then move it in to position.

Conduct after attaching the flat panel TV onto the stand.

Install Your Flat Panel TV

Attach the Light-Blocking Shield

Light-blocking shield

Front

Rear

Base cover

Note: Attach the light-blocking shield after anchoring the base cover on a flat stable place.

Peel off one side of the double-stick tape on the light-blocking shield and attach the shield onto the base cover.

Front

Note: Be careful that the light-blocking shield does not catch on the pipe insertion holes. Anchor the light-

blocking shield so that there are no gaps. If there is a gap, the light-blocking shield may peel off.

Rear

Install Your Flat Panel TV

• Connecting these speakers to another panel or device can damage the unit or cause a fire.

• When using tone control to increase treble, avoid overamplifying the volume.

Speaker bracket (For BOTTOM-Right)

Speaker bracket (For TOP-Right)

Screw holes

Speaker bracket (For TOP-Right)

Place the speaker so its terminals (bottom) are facing you.

Speaker bracket (For BOTTOM-Right)

Screw holes

(PRO-151FD)

Attach/Detach the Speaker

The flat panel TV’s speaker delivers high-quality, clear sound. Although other devices can be added or removed from the mounted panel, physically attach the speaker last. Disconnect the cables from the Speaker and REMOVE THE SPEAKER before mounting or moving the panel.

Before attaching the speaker to your mounted panel, review the information below.

• Lay the panel face down on a stable surface when attaching speaker brackets.

• Use only the supplied screws and tighten securely before stepping away.

• Handle the speaker carefully to protect the cabinet and grille net from scratches and other damage.

• Placing a CRT monitor near the speaker can cause a blur on the flat panel TV. Keep the distance between the speaker and the monitor.

Note: Use the foam packing materials to protect the equipment from scratches or other damage during

mounting.

Stand-Mounted Panel

1 ) Attach the appropriate speaker brackets (left and right) to the top and bottom on the back of the speakers

using the supplied screws.

Speaker bracket (For BOTTOM-Right)

Speaker bracket (For TOP-Right)

Screw holes

Speaker bracket (For TOP-Right)

Place the speaker so its terminals (bottom) are facing you.

Speaker bracket (For BOTTOM-Right)

Screw holes

(PRO-111FD)

Top, rear of flat panel TV

Top of flat panel TV

5 mm

Leave a space of about 5 mm

Speaker mounting hole

Install Your Flat Panel TV

2 ) Screw a supplied screw into the speaker bracket hole (lower of the two) at the top, rear of the panel.

Do not tighten it all the way yet. Leave it loose, with about 5 mm left to tighten.

Install Your Flat Panel TV

(PRO-111FD)

(PRO-151FD)

After passing the wide part of the hole over the screw, lower the speaker.

Tighten with the provided screw the bottom speaker bracket to the flat panel TV temporarily (one place bottom).

After passing the wide part of the hole over the screw, lower the speaker.

Tighten with the provided screw the bottom speaker bracket to the flat panel TV temporarily (one place bottom).

(PRO-111FD)

(PRO-151FD)

3 ) Hang the speaker bracket on the screw at the top by passing the wide part over it and lowering into the slot;

screw in the lower screw temporarily.

After passing the wide part of the hole of the speaker bracket (top) over the screw, lower the speaker onto it.

4 ) Adjust the position of the speaker then tighten the upper and lower screws firmly. 5 ) Tighten the two screws at the top and bottom for each speaker.

6 ) Pass the supplied speaker cable between the speaker and the panel (below the speaker bracket) from below. 7 ) Connect the speaker cables to the speaker.

Refer to “

2.2.2 Connect the Speaker Cables.”

Speaker cable

(PRO-111FD)

(PRO-151FD)

Speaker terminal

Insertion in groove

Speaker cable

Speaker terminal

Insertion in groove

tab

Gray

Speaker cable

Gray

Black

Speaker terminal

Black

Red

(PRO-151FD)

Install Your Flat Panel TV

8 ) Insert the cable in the groove on the speaker.

9 ) Connect the other end of the speaker cables to the rear of the panel.

Refer to “

2.2.2 Connect the Speaker Cables.”

Note: If the speaker needs to be repositioned (horizontally or vertically) after it is attached, loosen the speaker

mounting screws first. Adjust the position then retighten the screws.

2.2.2 Connect the Speaker Cables

1 ) Press down on the tab. 2 ) Insert the appropriately colored wire into the opening. 3 ) Allow a small percentage of the cable’s bare wire to remain visible. 4 ) Release the tab to clamp the wire.

If the bare wire is hidden when the tab is released, repeat Steps 1 through 4 until the proper amount of cable is showing.

5 ) Repeat this process for each cable, matching the color of the wire to the

appropriate terminal. 6 ) Connect the speaker cables to the speaker. 7 ) Bundle the speaker cables, power cord and other cables in the cable

clamp then insert the clamp into an appropriate hole on the rear of the

flat panel TV.

Refer to “2.7 Route then Bundle the Power Cord and Cables.”

Use the clamps as necessary (see page 33).

Install Your Flat Panel TV

Speaker cable

PRO-151FD

with the speaker installed

Black



Red



Gray

Cable clamp

(

PRO-111FD

)

Cable clamp

• Before connecting the speakers to the flat panel TV, unplug the panel from the power outlet. Connecting the speaker cable with the power cord plugged in can cause malfunction or damage to the panel if the cable’s bare wire touches other equipment. Plug in the power cord after connecting the speakers.

• Do not leave speaker cable wires bare and exposed at the terminals. Exposed wires can result in an electrical short causing malfunction or damage to the system.

• Do not connect any devices to the speaker terminals other than the speakers specified.

Installation bolts (1)

Installation bolts (2)

2.3 Wall/Ceiling Mounting

Lay the 50” panel down on a raised surface then remove the stand.

(PRO-111FD)

Fitting

2. Cord

1. Hook

12 mm to 18 mm (0.5 inches to 0.7 inches)

Install Your Flat Panel TV

A common flat panel TV mounting option is to hang the panel on a sturdy wall or from a reinforced ceiling. When mounting in this way, some preparations must be completed first. Follow the steps below to prepare the panel for mounting.

1 ) Attach the speaker brackets to the speaker (see page 19). 2 ) Attach the speaker to the panel (see page 21).

3 ) Connect the speaker cables to the speakers then to the panel (see page 22). 4 ) Connect cables for any other devices to the panel.

When deciding on a location for your flat panel TV, consider other equipment in the room. Equipment such as a DVR, Receiver, VCR, etc. requires some way to communicate with the panel, either directly or through another device. Review the instructions that came with the other equipment for available ports and terminals. After deciding which ports and terminals are needed, mark the connections on the flat panel TV for easier identification once the panel is mounted.

5 ) Temporarily bundle loose cables with rubber bands (not included). 6 ) Plug the flat panel TV’s power cord in to the panel but do NOT plug in to the power outlet. 7 ) Follow installation directions provided with your selected wall/ceiling mount.

For details, refer to the operating instructions supplied with the wall/ceiling mount unit.

2.4 Mount the Flat Panel TV

Because your flat panel TV is slim but heavy, have at least two people mount and/or position the panel. The following sections provide instructions for the different mounting and anchoring options.

Anchor the Panel When Using a Stand

When using a stand, stabilize the panel to keep it from tipping over. Please use the supplied metal fittings and screws to anchor the panel to a wall or other solid support structure.

Another option is to purchase hooks, cords, and fittings through your installer or from your local hardware store. The hardware size and strength depends on the composition and thickness of the anchoring surface.

Recommended hook: Nominal diameter 8 mm (3/8 inch), length 12 mm to 18 mm (0.5 inches to 0.7 inches)

To anchor the panel when using the provided stand, follow the steps below.

1 ) Attach the hooks to the mounting holes on the

back of the panel. 2 ) Sink the fittings into the wall or support structure. 3 ) Run cords between the hooks and the fittings. 4 ) Tighten the cords until the panel is anchored but

not pulled off balance.

Install Your Flat Panel TV

(PRO-151FD)

(PRO-111FD)

20 mm (13/16 inch) min.

8 mm to 15 mm

(3/8 inch to 5/8 inch)

4 mm (5/32 inch)

Wood screw (commercially available, 4 mm x 20 mm (5/32 inch x 13/16 inch) min.)

Wood screw (commercially available, 4 mm x 20 mm (5/32 inch x 13/ 16 inch) min.)

To stabilize the flat panel TV on a table or platform, use the supplied metal fittings and screws as well as commercially available wood screws. The wood screws are to anchor the metal fittings when mounting on a wooden surface. These screws should have a nominal diameter of 4 mm (5/32 inch) and are at least 20 mm (13/ 16 inch) long.

Notes: Avoid moving the table after the panel is attached.

Do not use bare wires for the cord. If any part of the wire is introduced into the ventilation port on the back of the display panel, fire or electrical shock could result.

Follow the steps below to secure your flat panel TV.

1 ) Mark locations for metal fittings and screws on the back edge of the table using the panel stand to determine

placement.

2 ) Drill holes in the table or platform edge at the marked locations. 3 ) Lift panel into place with the assistance with at least one other person. 4 ) Use wood screws (not included) to secure the metal fittings to the table.

Magnet

(Front)

(Rear)

Flat panel TV

Color sensor

Color sensor cable

Cable clamp

Color sensor

Color sensor terminal (upper bank)

Install Your Flat Panel TV

2.5 Attach the Color Sensor

When attached to your panel, the color sensor analyses the brightness of the environment to automatically optimize the picture quality according to the viewing condition. To activate this function, select OPTIMUM on the AV Selection menu, Mode 1 or Mode 2 on the Room Light Sensor menu (refer to “3.4.1 Adjust the Picture for Your Room Lighting.”

We strongly suggest you attach the color sensor to the bottom right of the front panel. It can be attached to the rear of the panel, but the color sensor may not operate properly depending on the conditions (refer to the Important bullets on page 28). For the actual procedure, follow the directions below.

Note: Do not connect any other external device, such as a keyboard to the color sensor terminal.

Do not connect the color sensor cable to a PC. To clean the sensor window, gently wipe with the supplied cleaning cloth. Do not use extension cables for the color sensor. Do not disassemble or modify the color sensor.

Attach the Color Sensor to the Front Panel (recommended)

This is a simple and easy-to-attach method using a magnet.

1 ) Attach the color sensor at the bottom right of the front panel using a magnet.

2 ) Attach the color sensor along the bottom edge of the front panel flush with the right side. 3 ) Connect the cable to the color sensor terminal on the rear upper bank but do NOT plug in to the power outlet.

Note: Use the cable clamps as necessary.

Install Your Flat Panel TV

(Bracket for PRO-151FD)

The bracket is for PRO-151FD panel but the procedure is the same for PRO-111FD.

Color sensor cable

Cable clamp

Color sensor terminal (upper bank)

Cable clamp

Color sensor

Speaker cable

Attach the Color Sensor to the Rear Panel

Methods of attaching the color sensor to the rear panel differ depending on the panel with or without sidemounted speakers.

(when side-mounted speakers are installed)

1 ) Remove the screws of the color sensor then replace the bracket.

Use the removed screws again.

2 ) Loosen the upper two (2) speaker bracket screws. 3 ) Fit the color sensor bracket’s lower grooves into the screws.

Adjust the color sensor/speaker bracket positions so as to stay in place.

4 ) Fasten the screws. 5 ) Connect the cable to the color sensor terminal on the rear upper bank but do NOT plug in to the power outlet.

Notes: Do not loosen the screws at the bottom of the panel. When attached to the rear panel, the sensor window

points upward. If the color sensor attached to the rear panel does not operate properly, attach it to the front panel. Do not use the supplied screws when attaching the color sensor using the speaker brackets. The color sensor may become hot due to a heat emitted from the panel. When using it in a hightemperature environment, attach the color sensor to the bottom of the front panel.

The bracket is for PRO-151FD panel but the procedure is the same for PRO-111FD.

Install Your Flat Panel TV

(when side-mounted speakers are not installed)

1 ) Remove the screws of the color sensor then replace the bracket.

Use the removed screws again.

2 ) Finger tighten the supplied color sensor screws in the speaker screw holes. 3 ) Fit the color sensor bracket’s lower grooves into the screws.

Adjust the bracket position to stay in place.

4 ) Fasten the screws. 5 ) Connect the cable to the color sensor terminal on the rear upper bank but do NOT plug in to the power outlet.

Important

The color sensor may not operate properly:

• if attached by methods other than specified above

• if anything blocks light falling on the sensor window

• if light falls on only part of the sensor window

• if the light falling on the sensor window and the panel screen differs

Notes: If the color sensor attached to the rear panel does not operate properly, attach it to the front panel.

The color sensor may become hot due to a heat emitted from the panel. When using it in a hightemperature environment, attach the color sensor to the bottom of the front panel. Do not use the screws supplied for the speakers.

Install Your Flat Panel TV

In order to watch both analog and digital broadcasts through your terrestrial antenna or cable connection, you must first connect the antenna cable to a splitter.

Rear view

When using a cable STB or Satellite STB, plug in to the antenna/cable TV wall outlet using the STB cable provided with your STB. If your STB has an HDMI terminal, use any of INPUT 4 through INPUT 6 (HDMI terminal) on the rear or INPUT 7 (HDMI terminal) on the side of the flat panel TV instead of making video connections. If you connect an antenna cable directly to TV, you must first connect the cable to a splitter. For details, refer to the operating manual that came with the STB.

Rear view

Satellite antenna

Cable STB/Satellite STB Cable STB/Satellite STB

2.6 Connect to Broadcast TV & Other Devices (DVR, Receiver, BDR, etc.)

The type of equipment attached to your flat panel TV determines which panel ports are used. The following sections explain how to connect broadcast TV and playback equipment such as a DVD player, Surround Sound system, video recorder, etc. to the panel. If your equipment is not listed, please refer to the operating instructions that came with the device(s) for connection assistance.

2.6.1 Add Analog (conventional) and Digital TV Channels

Whether a TV station broadcasts in Analog or Digital, your flat panel TV shows the programs as long as the panel is programmed to accept the signal. To program your panel for broadcast TV, select terminal ANT.

The ANT terminal accepts both analog and digital broadcasts. Connect a VHF/UHF antenna and/or cable TV to the panel’s rear ANT terminal, then press TV/DTV on the remote control to toggle between analog and digital broadcasts. When watching analog TV channels, you can also use an outdoor antenna for the clearest analog picture.

If your outdoor antenna uses a 75-ohm coaxial cable with an F-type connector, plug it into the panel’s antenna terminal on the back.

T W

2.6.2 Connect Your Other Pioneer Equipment

This section provides cabling information for your other Pioneer equipment when combined with the panel. Each diagram can also be used as a reference tool for non-Pioneer devices but port locations may differ or be unavailable.

Connect cable or Satellite using STB (Set Top Box):

SAT IN

COMPONENT

AUDIO

VIDEO OUTPUT

OUT

HDMI OUT

OUT

HDMI OUT

AUDIO

OUT

COMPONENT

VIDEO OUTPUT

T W

OUT

HDMI equipment

HDMI compliant cable (HDMI cable having the HDMI mark)

Rear view

INPUT 4 through INPUT 6 are HDMI terminals. Use INPUT 4 or INPUT 5 (HDMI) terminal when you also input analog audio signals. For details, refer to “5.2 Use HDMI Inputs.”

Audio cable (commercially available) Make this connection when inputting analog audio signals.

HDMI compliant cable (HDMI cable having the HDMI mark)

Also use INPUT 7 (HDMI terminal) on the side of the panel when connecting HDMI equipment. For details, refer to “5.2 Use HDMI Inputs.”

Left side view

HDMI equipment

Use INPUT 2 terminals when connecting a DVD player or other audiovisual equipment. If your DVD player has an HDMI terminal, use this connection instead of making video connections. For details, refer to the operation manual that came with the DVD player.

DVD player

Component video cable (commercially available)

AV cable

(commercially available)

Rear view

Use an optical digital cable to connect an AV receiver to DIGITAL OUT terminal (optical). If your AV receiver does not have a DIGITAL IN terminal (optical), you may connect the panel’s AUDIO OUT terminal (audio) to the audio input terminal on the AV receiver. For details, refer to the operation manual that came with the AV receiver.

This connection is not required when connecting an AV amp equipped with the surround function to a subwoofer.

Optical digital cable (commercially available)

Subwoofer

AV cable (commercially available)

Rear view

AV receiver

Install Your Flat Panel TV

Connect HDMI equipment (INPUT 4 through INPUT 6):

T W

Connect HDMI equipment (INPUT 7):

Connect a DVD player: Connect an AV receiver:

T W

Install Your Flat Panel TV

Use INPUT 1 terminals when connecting a VCR or other equipment. For details, refer to the operation manual that came with the VCR.

VCR

S-Video cable (commercially available)

AV cable (commercially available)

Rear view

Use INPUT 3 terminals when connecting a game console, camcorder or other audiovisual equipment. For details, refer to the operation manual that came with the game console or camcorder.

Left side view

AV cable (commercially available)

Camcorder/Game console

Rear view

Connect control cords between the panel’s CONTROL (OUT) terminal and other Pioneer equipment having the SR logo. Use a mono sound cable with a mini plug (not provided).

Personal computer

Rear view

Use the PC INPUT terminal (Analog RGB) when connecting a PC. If you also connect PC audio, use PC INPUT (Audio) with a stereo sound cable with a mini plug (not provided). For details, refer to the operation manual that came with the PC.

Stereo sound cable with a mini plug (commercially available) (When PC audio is connected)

RGB cable (commercially available)

Connect a VCR: Connect a game console or camcorder:

T W

Connect control cords: Connect a PC:

T W

CONTROL

OUT

T W

Speaker cable

Cable clamp

(PRO-151FD)

(PRO-111FD)

Speaker cable

Cable clamp

Bundle cables in small

groups when possible for

easier separation later,

if necessary.

PRO-151FD

PRO-111FD

Install Your Flat Panel TV

2.6.3 Connect the Power Cord to the Panel

The final connection is the power cord. Always connect the panel’s power cord to a three-pronged outlet, verifying that the cord is properly grounded. The cord includes a noise filter that reduces electrical interference from the wall outlet.

As long as the flat panel TV is plugged in to an outlet, some power is drawn through the panel. When the flat panel TV is not going to be used for a long period, unplug the panel from the power outlet. Unplugging the panel extends the life of the plasma as well as saves energy.

Plug the cord in to the panel but do NOT plug it in to a power outlet yet.

2.7 Route then Bundle the Power Cord and Cables

Once the flat panel TV is mounted and the speaker is attached, place additional equipment in the final position(s). Lay out the power cord, panel cables and any other device cables in a logical pattern that works for the location. Please consider the following points when routing cables:

• Access to a 3-prong (grounded) power outlet

• Space for the noise filter between the panel and outlet

• Placement of cables under carpets or across walking paths

T W

Usually the cord/cables have slack or are too long. Although rubber bands are a good temporary solution to bundle cables, they tend to break down too quickly. To keep cables organized and neat, use the included cable clamps to bundle cables. The diagram below shows a bundled speaker cable.

T W

A reusable cable clamp is designed to lock the bundled cables in place. Your flat panel TV has a total of four holes to attach cable clamps to the back of the panel. Use the cable clamps as necessary.

Install Your Flat Panel TV

Cable clamp Latch

Lever

Follow the steps below to attach a cable clamp.

1 ) Thread the clamp band through the holder and bundle the cable(s) in the cable clamp. 2 ) Push and hold the levers then insert the hook into an appropriate hole on the rear of the flat panel TV. 3 ) Pull up the clamp band to lock.

4 ) Confirm that the cable clamp is seated firmly in the panel.

Note: Avoid pinching or creating pressure points when routing or bundling cables.

To remove the clamp band, pull and hold the latch to release. To remove the cable clamp, push and hold the levers then pull it out from the hole.

Note: The longer a clamp is in place, the better chance of deterioration. An older clamp is more easily damaged

while being removed and may not be reusable.

Power On indicator

Standby indicator

Sleep indicator

(PRO-111FD)

Basic Operations For Television Viewing

3 Basic Operations For Television Viewing

This chapter explores day-to-day operations such as powering on your flat panel TV, using the Home Menu, and adjusting the panel for the viewing area/room. The final section in this chapter provides hints and suggestions for those new to flat panel TV features.

3.1 Turn the Flat Panel TV ON/OFF

Your flat panel TV has three activity levels: Power On, Standby, and Power Off. Standby saves energy but allows the remote control to turn on the panel. The following instructions use the remote control. To operate the flat panel TV through the side panel buttons, refer to “1.2.1 Control Buttons and More on the Flat Panel TV” for button locations.

Turn ON the Flat Panel TV

To turn on the panel, follow the steps below.

1 ) Plug the flat panel TV’s power cord in to a properly grounded outlet. 2 ) Press any of the following buttons to turn the flat panel TV On.

• Power On button (a) on the panel’s back in lower-left section (see page 9)

• STANDBY/ON button on the side of the panel (see page 8)

• Remote control’s TV (a) button located in the upper left corner (see page 12).

Images appear on the panel screen.

Note: Use the remote control’s

3 ) Confirm that the Power ON indicator lights blue.

Note: While in Standby, pressing the remote control’s

Turn OFF the Flat Panel TV

Turning off the flat panel TV can mean entering Standby so features such as Sleep are still functional or it can mean cutting power to the panel. Unless the flat panel TV is to sit idle for long periods, leave the panel in Standby.

Note: While in Standby or when powered off, the flat panel TV continues to draw some power as long as the panel

is plugged in to an outlet.

Follow the steps below to place the panel in Standby.

1 ) Press the remote control’s TV (a) button or

panel’s STANDBY/ON button.

2 ) Confirm that the Standby indicator lights red.

The table to the right provides samples of how the indicators light. Monitor the indicators On the front of the panel to check the power status.

Note: Select from Auto, High, Mid and Low. Selecting

Auto toggles the brightness of the Power On indicator between High, Mid and Low to match the brightness level of the viewing area. Refer to “Blue LED Dimmer” (page 46).

MUTING

button to reduce any excessive static noise.

TV (a)

button causes the flat panel TV to turn On.

Power On

Indicator

Standby

Indicator

Flat Panel TV Status

Panel’s power cord is disconnected or the power cord is connected but the flat panel TV’s Power On button (a) is off

Power is on but waiting for activation

Panel is in Standby

Basic Operations For Television Viewing

EDIT/LEARN

INPUT

RCV VCRSAT

CBL

DVR

DVD

SELECT

INPUT

TV/DTV

DISPLAY

SCREEN

SIZE

SELECTION

SAT GUIDE

DVD

TOP MENU

SAT / DVD MENU

HOME MENU

RETURN

ENTER

Remote control

Home Menu screen

3.2 Program the Flat Panel TV for Television Viewing

To watch TV and take advantage of some built-in features, choose the channel type or types (Analog, Digital), select a language, set your time zone, and program the channels. The sections below include how to set your channel type and how to use the Home Menu for each programming option.

3.2.1 Choose Analog or Digital TV Channels

To choose a channel setting, note the antenna input terminal connected to the back of the panel. Follow the directions below to select analog or digital TV channels.

1) Confirm that the remote control is set to TV.

Located at the bottom of the remote control.

2) Press TV/DTV on the remote control.

Located at the top of the remote control.

3) Select a channel option, analog or digital.

During operation, press TV signals.

Note:

See

“2.6.1 Add Analog (conventional) and Digital

TV Channels”

setting options.

for more information about channel

TV/DTV

to toggle between

Note: When watching TV and separate video image (multi-screen), pressing the remote control’s

TV/DTV

changes only the TV signal appearing on the left side of the panel.

3.2.2 Explore the Home Menu

The Home Menu is the main menu for the flat panel TV. Most commands and settings are programmed through this menu. The following section describes a typical method for working with the panel’s menus. For actual procedures, see the appropriate page(s) that describe a function.

1) Press HOME MENU on the remote to access the main menu.

2) Use the Up/Down arrows (/ ) to highlight a menu item.

3) Use the Left/Right arrows (/ ) to scroll through options for that menu item.

Channel Favorites Input Home Media Gallery HDMI Control Setup

4) Highlight the selected menu option.

5) Press ENTER to lock in the change.

6) Press RETURN to move back to a previous menu/submenu page when changing more than a single option.

7) Press HOME MENU again to exit the menu screen.

button

Basic Operations For Television Viewing

This chart provides a breakdown of the Home Menu for both AV and PC sources.

AV Source Pg Option

Channel 42 — Favorites 42 — Input 42 — Home Media Gallery 93 — HDMI Control 86 — Setup Picture 57 AV Selection

61 Contrast* 61 Brightness* 61 Color* 61 Tint* 61 Sharpness* 64 Pro Adjust* 63 PureCinema** 49 Sound Control*** 48 OPTIMUM

Performance***

61 Reset

Sound 49 Treble

49 Bass 49 Balance 75 Sound Effect 49 Reset 75 AVC

Power Control 56 Energy Save

76 No Signal off 76 No Operation off

Sleep Timer 44 — Option 47 Position

59 Auto Size 62 Side Mask 84 HDMI Input 91 HDMI Control Setting 46 Blue LED Dimmer 56 Orbiter 56 Video Pattern 59 Game Control Pref 45 Room Light Sensor 55 Screen Protection 43 Label Input

System Setup 38 Auto Installation

39 Analog TV Setup 41 Digital Tuner Setup 50 Parental Control 72 Closed Captions

121 Digital Audio Output

50 Change Password 37 Language

124 Technical Info

Favorites Setup 42 Channel Mode

43 Sort Favorites

* Available when any option other than OPTIMUM is selected from the

AV Selection menu.

** Access this option through the Pro Adjust menu when any option

other than OPTIMUM is selected from the AV Selection menu.

*** Available only when OPTIMUM is selected from the AV Selection

PC Source Pg Option

Channel 42 — Favorites 42 — Input 42 — Home Media Gallery 93 — HDMI Control 86 — Setup Picture 57 AV Selection

61 Contrast 61 Brightness 61 Red 61 Green 61 Blue 61 Reset

Sound 49 Treble

49 Bass 49 Balance 75 Sound Effect 49 Reset 75 AVC

Power Control 56 Energy Save

77 Power Management

Sleep Timer 44 — Option 122 Auto Setup

122 Manual Setup

84 HDMI Input 91 HDMI Control Setting 56 Orbiter 43 Label Input

Favorites Setup 42 Channel Mode

43 Sort Favorites

Basic Operations For Television Viewing

TV Screen Components

Your flat panel TV has easy-to-read menus and graphic symbols that provide quick access to the desired options. Menus appearing in this manual may differ slightly from the actual menus but the functionality remains the same.

Exit

Treble : 0 Bass : 0

4 8

Balance : 0 Sound Effect : Reset AVC : Off

xxxxxxxxxxxxxxxxxxxx

xxxxxxxxxxxxxxxxxxxxxx

HOME MENU Return

5 6 7

1 - Exit button: Close the menu to return to TV

viewing 2 - Menu title: Display the selected menu title 3 - TOOLS button: Display the TOOLS Menu 4 - Menu: Select an option

2 3

Sound

TELEVISION

6 - Operation Guide area: Display the operational

guidelines for the selected option(s)

7 - Return button: Return to the previous menu

screen

8 - Picture preview (in reduced size)

5 - HOME MENU button: Close the menu to return

to TV viewing

3.2.3 Assign a Language

The default menu language is English. To assign a different language for menus and on-screen information, follow the steps below.

1 ) Press HOME MENU.

Setup

2 ) Select

Use the arrow buttons to highlight an option then press

3 ) Select 4 ) Select

from the main menu.

System Setup Language

from the Setup menu.

from the System Setup menu.

ENTER

5 ) Select a language from the submenu.

Menu : English

6 ) Press HOME MENU again to exit the menu.

Basic Operations For Television Viewing

3.2.4 Set the Clock

Set the flat panel TV’s clock to take advantage of many built-in features such as Time Zone and D.S.T. (Daylight Saving Time) activation for digital TV broadcast.

Note: If the panel’s power cord is unplugged or there is a power outage, the time must be reset.

Follow the steps below to set the clock.

1 ) Access the 2 ) Select 3 ) Select 4 ) Select 5 ) Select the time zone for your area.

6 ) Select the menu option 7 ) Select the proper option for your location. 8 ) Press HOME MENU to close the menu and exit.

System Setup Digital Tuner Setup Clock

from the Digital Tuner Setup menu.

Time Zone

from the options.

through the

from the System Setup menu.

Time Zone : Atlantic D.S.T. : On

D.S.T.

to activate/deactivate Daylight Saving Time.

Setup

3.2.5 Create the List of Channels

This section describes how to search for and set up TV channels. There are two ways to add channels to your flat panel TV, Auto Installation for automatic channel selection or manual channel assignments. The Auto Installation adds all available channels from your selected TV provider. Once all channels are added to the list, simply delete any unwanted channels. This section provides steps to add/remove channels.

Auto Installation

Auto Installation searches for and adds TV channels to your list of viewable channels. Using the remote control, follow the steps below to automatically select all available channels.

1 ) Access the 2 ) Select 3 ) Select 4 ) Select an option.

• Signal type: Air or Cable

• Language: English, Français or Español

•Time Zone: Atlantic, Eastern, Central, Mountain, Pacific, Alaska, or Hawaii

System Setup Auto Installation Air/Cable, Language

through the

from the System Setup menu.

, or

Time Zone

Setup

from the Auto Installation menu.

Basic Operations For Television Viewing

5 ) Select Start.

The panel automatically begins creating your list of channels.

Language : English Air/Cable : Cable Time Zone : Atlantic

Start

Note: To quit Auto Installation before it is complete, press

EXIT

Manual Channel Selection

To add channels without using the Auto Installation option, follow the directions below. Also, if a channel is skipped in error, use this method to add the channel to your list.

1 ) Access the 2 ) Select 3 ) Select 4 ) Select 5 ) Select a channel number to be added.

System Setup Analog TV Setup Manual Adjust Program Entry

Use the arrow buttons

6 ) Select 7 ) Select

Store

from the Manual Adjust menu.

Yes

from the submenu.

through the

from the System Setup menu.

from the Analog TV Setup menu.

(/)

to enter a channel number.

Program Entry : 1 Store : Yes Tuner NR : On

Setup

RETURN

to recall the Auto Installation screen then

8 ) Press HOME MENU to exit the menu after all wanted channels have been added.

Note: Analog channels can be added manually but digital channels can only be added using the Add New

Channels button on the Digital Tuner Setup menu.

Add New Channels

To add new channels, follow the steps below.

1 ) Access the 2 ) Select

Digital Tuner Setup

System Setup

through the

from the System Setup menu.

Setup

Basic Operations For Television Viewing

3 ) Select

4 ) Select

Installation

from the Digital Tuner Setup menu.

Add New Channels

Installation Channel management Clock

Channel search starts automatically. If a new channel is found, it is stored automatically in the flat panel TV. To cancel channel search before it finishes, press

RETURN

Software Keyboard

This on-screen keyboard allows labeling manually added TV channels. Channel labels can be up to eight characters long to help channel identification. To use the Software Keyboard for labeling TV channels, follow the steps below.

1 ) Access the 2 ) Select 3 ) Select

Analog TV Setup Label

System Setup

from the Analog TV Setup menu.

through the

Setup

from the System Setup menu.

4 ) Select

Program Entry

from the submenu.

5 ) Select a program number.

• Cable: 1 through 135

• Air: 2 through 69

Label

6 ) Select

The Software Keyboard screen appears.

Label

INPU

1234567890 ABCDEFGH I J KLMNOPQRST UVWXY Z , . : ; &'()+-* /_@

Delete Space

Caps

OK Cancel

7 ) Select the first character.

The cursor moves to the next character space.

8 ) Repeat the previous step to enter up to eight characters.

• To change a character, use  or  to highlight the character then press

ENTER

. The cursor moves to the

previous or next character.

ENTER

• To delete the entered character, highlight the character, select Delete then press

• To put a space after the entered character, highlight the space, select Space then press

ENTER

• To toggle between upper case and lower case, highlight the character, select Caps then press

ENTER

Basic Operations For Television Viewing

9 ) Select OK then press ENTER.

The entry is complete.

10 ) Press HOME MENU to exit the menu.

3.2.6 Skip or Delete Unwanted Channels

The Auto Installation process adds all channels available from your TV service provider. However, there may be some channels that are unwanted or are not age-appropriate for your home. This section explains how to bypass or delete unwanted channels when moving up/down one channel at a time and what programs are available for viewing.

To skip or delete unwanted channels, use the remote’s CH+/CH– buttons to reset the status for those channels. Follow the steps below to change a channel’s status.

1 ) Access the 2 ) Select

System Setup

Digital Tuner Setup

• Digital TV channels: Channel management > Channel Options > (Channel Delete) > (On)

through the

Analog TV Setup

XXXX 00001.000 XXXX 00002.000 XXXX 00003.000 XXXX 00004.000 XXXX 00005.000 XXXX 00006.000 XXXX 00007.000 XXXX 00008.000 XXXX 00009.000

Setup

from the System Setup menu.

3 ) Scroll to or highlight an unwanted channel number. 4 ) Press ENTER to reverse the status for that channel.

When there is a check mark next to the channel, it disappears.

5 ) Press RETURN.

A confirmation screen appears.

6 ) Select

Yes

then press ENTER.

The Channel Delete setting is complete.

7 ) Press HOME MENU to exit the menu.

If you select the (Channel Skip) option in Step 3, the setting is complete when exiting the Channel Options menu (no confirmation screen appears). Skip Steps 5 and 6.

The instructions for restoring a skipped channel are the same as above. In Step 4 a check mark appears next to the added/restored channel.

To skip an analog channel, follow the steps below.

• Analog TV channels: Manual Adjust > Store > No

Radio Skip

This function allows skipping of radio channels at a time. To set this option, follow the steps below.

1 ) Access the 2 ) Select 3 ) Select 4 ) Select

Digital Tuner Setup Channel management Radio Skip

System Setup

from the Channel management menu.

through the

Setup

from the System Setup menu.

from the Digital Tuner Setup menu.

5 ) Select

6 ) Press HOME MENU to exit the menu.

Basic Operations For Television Viewing

3.2.7 Channel List

Your flat panel TV offers three channel lists for quick access to a desired channel: Favorites List, Channel List and Input List.

Favorites List: Display your favorite channel numbers/names up to 20 channels (analog channels, Input 1 through 7, PC), 20 digital channels, and 1 Home Media Gallery (top screen, see page 98)

Store your most frequently viewed channels in the Favorites List. To display the Favorites List, press ENTER while showing a TV channel. For another method to access the Favorites List, follow the directions below.

1 ) Press HOME MENU. 2 ) Select

Favorites

from the main menu. Pressing the / button while showing the Channel List or Input List also causes the Favorites List to appear.

Channel List: Display all analog/digital TV channels in each broadcast network group

To display the Channel List, follow the directions below.

1 ) Press HOME MENU. 2 ) Select

Channel

from the main menu. Pressing the / button while showing the Favorites List or Input List also causes the Channel List to appear.

Input List: Display external input source names from INPUT 1 through INPUT 7 and PC

To display the Input List, follow the directions below.

1 ) Press HOME MENU.

Input

2 ) Select

from the main menu. Pressing the / button while showing the Favorites List or Channel List also causes the Input List to appear.

Note: After selecting the desired channel, pressing

screen appears. Pressing

RETURN

EXIT

ENTER

causes the Channel List to close and the selected

causes the Channel List to close and the screen before

selection returns. Press an arrow button to cycle through the lists when viewing any of the lists.

Favorites

INPUT 6 XXXXXX 00001.000 XXXXXX 00004.000 XXXXXX 00007.000 XXXXXX 00009.000 PC XXXXXX XXXXXX 00013.002 XXXXXX 00015.000 XXXXXX 00024.000 1/2

Set Favorite Channels

Select up to ten (10) channels per list page, up to five pages for a total of 41 favorite channels. To assign channels to your

Favorites

1 ) Access the 2 ) Select 3 ) Select

All

, follow the steps below.

Favorites Setup Channel Mode All

Favorites

through the

Setup.

from the Favorites Setup menu. from the Channel Mode menu.

• To assign all channels, select All. To assign the registered channels, select Favorites.

Basic Operations For Television Viewing

4 ) Select a TV channel to store.

If the screen fails to fit in the window, a scroll bar appears. Pressing

ENTER

Favorites list is empty, “No Favorites List.” appears.

5 ) Press HOME MENU to exit the menu.

Alternate Method to Store your Favorite Channels

Use the TOOLS Menu to store TV channels, external input sources including PC, and Home Media Gallery contents. To store channels, follow the steps below.

1 ) Press TOOLS.

The TOOLS Menu appears on screen.

while watching a TV program also causes the favorite channel list to appear. If the

2 ) Select

Favorites Entry

Use the arrow buttons to highlight an option.

3 ) Select On (/ ).

The channel you are watching is stored in the favorite list. To cancel, use the arrow button to select Off.

Notes:

•Pressing

EXIT, RETURN

, or

TOOLS

again causes the TOOLS Menu to disappear.

• Once the maximum number of channels are stored, a warning screen appears.

• To quit the procedure before it finishes, press

RETURN

on the remote control.

EXIT

Sort Favorite Channels

To sort theough the store channels, follow the steps below.

1 ) Access the 2 ) Select

Sort Favorites

Favorites Setup

through the

Setup

from the Favorites Setup menu. 3 ) Select a channel to move. 4 ) Select a new location then press ENTER.

The selected channel is moved to the new location. To sort another channel(s), repeat Steps 3 and 4.

5 ) Press HOME MENU to exit the menu.

Edit the Input List

To change name of an Input, follow the steps below.

Option

1 ) Access the

through the

Setup

2 ) Select

Label Input

from the Option menu.

3 ) Select an input or PC.

The software keyboard appears.

4 ) Enter the new name.

5 ) Select

To cancel, press

to save the name and exit the menu.

HOME MENU

Label

KIDS

1234567890 ABCDEFGH I J KLMNOPQRST UVWXY Z , . : ; &'()+-* /_@

Delete

Space

Caps

OK Cancel

Basic Operations For Television Viewing

3.3 Quick Start for Watching Television

Your flat panel TV has many functions and features, some of which you may simply lack the time to set when first installing the panel. To begin watching TV quickly, refer to the basic information within this section. However, when it is convenient, we strongly suggest going through the rest of this manual and learning all that your flat panel TV can do.

3.3.1 Change the Channel/Sub-Channel

With the remote control pointed at the panel’s remote sensor, press the CH + button to sequentially change to the next highest available channel. The CH – button sequentially changes down to the next lowest available channel. Each press of CH + or CH – causes the channel to change sequentially from station to station. To return to the previous channel, press CH RETURN. To toggle between the two channels, press CH RETURN again. Each press of this button switches the channel between these two stations.

Another option for changing the channel is to use the number buttons (0 through 9). Simply press the number buttons in the order needed for that channel. For example, enter Channel 231 as 2 number, 4

A recent addition to TV viewing is the Sub-channel. A digital channel can be split in to multiple signals. Each signal, called a sub-channel, can carry a different program. To watch a sub-channel, use a combination of number buttons and the dot (.) button. For example, if Channel 5 is digital and has three active sub-channels, enter 5 . 2 to reach the second sub-channel.

Note: To tune in a program more quickly, enter the channel or sub-channel then press

- 3 - 1 or Channel 4 as the single

CH ENTER

3.3.2 Adjust the Volume/Sound

With the remote control pointed at the panel’s remote sensor, press and hold VOL+ to increase the sound volume gradually. Holding down VOL– decreases the volume at the same rate. A single press of VOL+ or VOL– causes the volume to adjust by minor increments.

To silence all sound, press MUTING. The muting symbol ( previous level, press MUTING again. Pressing VOL+ once also increases the volume one step higher than the current level and cancels the muting mode.

If the panel’s default sound level is too loud or too soft, refer to “3.4.6 General Sound (Audio) Adjustment.”

e ) appears on screen. To return the volume to the

3.3.3 Turn On the Sleep Timer

To save energy and to maximize the life of your flat panel TV, try using the Sleep Timer for occasions when the panel may be left on by accident. The Sleep Timer places the panel in Standby when the selected time elapses. The Sleep Timer provides time periods of 30, 60, 90, or 120 minutes. When the Timer is down to five minutes, a reminder appears on screen each minute until the time has elapsed.

To set the Sleep Timer, follow the steps below.

1 ) Access the

Sleep Timer

through the

Setup.

2 ) Select the desired time period.

Select between 30 minutes and 2 hours (120 minutes).

3 ) Press HOME MENU to exit the menu.

Basic Operations For Television Viewing

The SLEEP indicator on the front of the flat panel TV lights orange when the Sleep Timer is set. To check the remaining time, press TOOLS then select Sleep. “Remain ---min” appears at the top of the menu screen. After checking the time, press EXIT to return to your program without losing the Sleep Timer setting.

Note: When the sleep timer has been set, “Remain ---min” appears at the top of the menu. However, the Video

Pattern timer has priority over the sleep timer. When the Video Pattern timer is on, the sleep timer is deactivated. Video Pattern is explained fully later in this manual.

3.4 Adjust the Picture and Sound Quality

Your flat panel TV has many adjustment options for the picture and the sound to make it just right for you. This section provides basic adjustments but for detailed video/audio modifications, refer to “4 Additional Picture and Sound Adjustment Options” and “4.7 Select Alternatives for/to Sound.”

3.4.1 Adjust the Picture for Your Room Lighting

The flat panel TV senses the amount of light in your room and automatically adjusts the screen brightness for the best picture. Bright rooms require stronger coloring so images appear crisp while dimly lit rooms allow the picture to use more subtle coloring. Set the Color Sensor function to On for best coloring possible for the selected image and viewing environment (refer to “2.5 Attach the Color Sensor” on page 26 for details on how to attach the sensor).

The panel ships with the Room Light Sensor turned Off. The sections below provide directions to turn the room lighting sensor and color sensor On/Off.

Room Lighting Sensor

To deactivate/reactivate the room lighting sensor, follow the steps below.

1 ) Access the 2 ) Select 3 ) Select

Room Light Sensor Mode 1

Off No effect Mode 1 automatically adjusts the picture brightness for the

Mode 2 automatically adjusts the picture brightness and

Option

through the

Mode 2

Option Description

Setup.

from the Option menu.

(or

Off

) from the submenu.

best possible image quality based on the information collected at the Room Light Sensor and Color Sensor

coloring for best image quality possible for the viewing environment based on the information collected at the Room Light Sensor and Color Sensor

Note: If the color sensor is not in use, adjustments are made for Mode 1 and Mode 2 based on the information

collected at the Room Light Sensor.

Game Control Pref : Off Room Light Sensor : Off Screen Protection Label Input

4 ) Press HOME MENU to exit the menu.

Basic Operations For Television Viewing

Blue LED Dimmer

Adjust the brightness of the POWER ON indicator depending on the brightness level of the viewing area. Setting to Auto toggles the brightness of the indicator between High, Mid and Low to match the brightness level of the viewing area. To set the indicator, follow the directions below.

Option

1 ) Access the

through the

Setup.

2 ) Select 3 ) Select

Blue LED Dimmer Auto, High, Mid

from the Option menu.

Low

from the submenu.

4 ) Press HOME MENU to exit the menu.

3.4.2 General Picture (Video) Adjustment for an AV Source

The directions below apply to all AV sources except OPTIMUM. If the viewing option is OPTIMUM, your flat panel TV automatically adjusts the picture to the best possible level.

1 ) Access the

Picture

through the

Setup.

2 ) Select an item to be adjusted.

Contrast is used in the example below.

Picture

AV Selection : PERFORMANCE Contrast : 40 Brightness : 0 Color : 0 Tint : 0 Sharpness : 0 Pro Adjust Reset

3 ) Use the arrow buttons (/) to adjust to the desired level.

Contrast

4 ) Press HOME MENU to exit the menu.

Reduce Noise from Analog TV

Sometimes electronic signal static can cause imperfections in the picture. This static is called Video Noise. Your flat panel TV can reduce video noise from an analog TV channel, depending on the broadcast signal level. Sometimes the broadcast signal has higher interference levels so that some video noise is noticeable.

This function is only selectable for signals from an antenna. Follow the steps below to reduce noise on an analog TV channel.

1 ) Access the 2 ) Select 3 ) Select

Analog TV Setup Manual Adjust

System Setup

through the

Setup.

from the System Setup menu.

from the submenu.

Only analog channels set using Auto Installation are manually adjustable.

4 ) Select

Program Entry.

5 ) Select a channel number to be added.

Use the arrow buttons (

6 ) Select 7 ) Select

Tuner NR. On.

/

) to enter a channel number.

The default setting is On.

8 ) Press HOME MENU to exit the menu.

Basic Operations For Television Viewing

Picture Image Position

Each input source stores the picture adjustment settings for that view. Although repositioning is available in most screen views, when the screen is set to Dot-by-Dot, the Position menu is unavailable. Also, depending on the displayed video, the image position may not change after an adjustment.

To adjust the picture’s horizontal and vertical position, follow the steps below.

Option

1 ) Access the 2 ) Select

Position

through the

from the Option menu.

Setup.

Position Auto Size : Off Side Mask HDMI Input HDMI Control Setting Blue LED Dimmer : Auto Orbiter : Off Video Pattern

3 ) Select

H/V Position Adjust

from the submenu. 4 ) Adjust the vertical and/or horizontal positioning using the arrow buttons. 5 ) Press HOME MENU to exit the menu.

Restore Default Picture

After making multiple adjustments, it may be difficult to reverse improper settings. To restore the factory default video settings, follow the directions below.

Reset

1 ) Highlight

from the Picture menu.

2 ) Press ENTER to continue with the picture reset.

A confirmation screen appears asking if settings should be returned to the factory defaults.

3 ) Use the arrow buttons to highlight

Yes.

4 ) Press ENTER.

All video settings return to the original default values when selecting options other than OPTIMUM or PC. When OPTIMUM is selected, video settings for OPTIMUM. AV Selection menus, and Sound Control

settings return to the original default values.

3.4.3 Compare Images When Adjusting the Picture

When adjusting the picture, look for an overall improvement by adjusting each parameter or option one at a time. Many small adjustments lead to the best picture for your viewing area. As each option changes, refer back to the previously set image for comparison. This section includes adjustment notes and steps to adjust the flat panel TV’s picture.

Each parameter/option must be adjusted separately. For example, if two options under AV Selection, PERFORMANCE and MOVIE need adjustment, change/compare one option then save the preferred setting before moving on to the other option. Below are other guidelines to follow when adjusting the picture.

Before

• Adjustments are available while on the After screen. Trying to make adjustments while on the

causes

a warning message to appear.

• Switch to another parameter/option only from the

Before

another option, the

• Exiting an option from the

data is lost.

Before

screen stores that previous entry in memory and deactivates the button.

After

screen stores the new entry in memory and deactivates the TOOLS button.

screen. If viewing the

Before

screen when selecting

After

• Moving/changing the AV Selection parameter/option stores the option setting in memory (button continues to work).

Basic Operations For Television Viewing

Follow the steps below to adjust options for the preferred picture quality.

1 ) Access the

Picture

2 ) Select an option. 3 ) Use the TOOLS button to toggle between the previous and adjusted images. 4 ) Repeat Steps 2 and 3 to continue adjusting the option as needed. 5 ) Repeat Steps 2 through 4 to adjust other picture options. 6 ) Press HOME MENU to exit the menu.

Note: if no selections are made within 60 seconds, the menu closes automatically and the current settings are

saved to memory.

To exit the menu without saving the changes, switch to the Before screen then press HOME MENU.

3.4.4 Display a Graphical Picture/Sound Adjustment Screen

Selecting

OPTIMUM

submenus. Select Performance provides an on-screen graphic monitor for multiple picture and sound adjustments.

OPTIMUM Performance

OPTIMUM Performance displays on-going picture and sound adjustments using graphical data when selecting OPTIMUM from the AV Selection menu. OPTIMUM Performance provides the following bar graph data:

• Analyzer: Histogram, RGB, Room Light, Color Sensor

• Picture: Contrast, Brightness, Color, Sharpness, Color Temp, Gamma

•Sound: Level

through the

Setup.

from the AV Selection menu causes the Picture menu to display different AV source

for the Sound Control option to automatically adjust the sound quality, and OPTIMUM

OPTIMUM Performance [OPTIMUM] On

OPTIMUM On/Off

[Analyzer]

Histogram RGB Room Light Color Sensor : Disable

[Picture] Contrast Brightness Color Sharpness Color Temp Gamma

[Sound]

60 1k 12k(Hz)

To display OPTIMUM Performance, follow the procedure below.

1 ) Access the 2 ) Select 3 ) Select 4 ) Select

Picture AV Selection OPTIMUM OPTIMUM Performance

The OPTIMUM Performance appears. To cancel the OPTIMUM Performance option, press

Note: When OPTIMUM is selected, press and hold

through the

Setup.

from the Picture menu.

from the AV Selection menu.

from the Picture menu.

DISPLAY

EXIT

on the remote control to show OPTIMUM

Performance.

OPTIMUM Performance compares the picture and sound quality between “Off” (unadjusted) and “On” (adjusted using the

TOOLS

button).

Basic Operations For Television Viewing

3.4.5 Sound Control

Setting the Sound Control option to On automatically adjusts to the highest sound quality possible for the selected image and viewing environment. This option is also available when OPTIMUM is selected in the AV Selection menu. To activate Sound Control, follow the procedure below.

Picture

1 ) Access the

through the

Setup.

2 ) Select 3 ) Select 4 ) Select 5 ) Select 6 ) Press HOME MENU to exit the menu.

AV Selection OPTIMUM

from the AV Selection menu.

Sound Control On.

from the Picture menu.

Note: When Sound Control from the Picture menu is selected, the only Sound menu option available is AVC (Auto

Volume Control).

3.4.6 General Sound (Audio) Adjustment

Many prefer a heavier base when watching movies or music vide os from an AV source or on TV. O the rs li ke a more balanced sound. To adjust the sound to your preference, follow the directions below.

Sound

1 ) Access the 2 ) Select an option for adjustment.

through the

Setup.

Treble : 0 Bass : 0 Balance : 0 Sound Effect Reset AVC : Off

3 ) Use the left/right arrow buttons (/) to adjust the option.

Option Left Button Right Button

Treble weakens tone strengthens tone Base weakens tone strengthens tone Balance shifts audio balance to the left shifts audio balance to the right

4 ) Press HOME MENU to exit the menu.

Restore Default Sound Setting

To restore the factory default sound settings, follow the directions below.

Reset

1 ) Highlight 2 ) Press ENTER to continue with the sound reset.

from the Sound menu.

A confirmation screen appears asking if settings should be returned to the factory defaults.

3 ) Use the arrow buttons to highlight 4 ) Press ENTER to restore all sound settings to the original default values.

Yes.

Note: The Auto Volume Control (AVC) setting cannot be restored to the factory default.

Basic Operations For Television Viewing

3.5 Block Programs, Channels, or Content

Although blocking programs, channels, or content is optional, some images may be inappropriate for all family members. Your flat panel TV supports a blocking function known as Parental Control. With Parental Control activated, certain material fails to appear on screen if it is beyond your select viewing level. Parental Control uses recognized rating systems but also allows blocks placed at your discretion. This section explains the different blocking functions and how to assign each type.

Note: When watching a TV program, you may see an emergency alert message scrolling at the top of the screen.

The television station is broadcasting the emergency message as a test or an alert in a real emergency. The flat panel TV ships with this function active. For information about emergency messages, refer to

Assign a Rating System to Create Blocks”

3.5.1 Assign a Parental Control (Block) Password

With Parental Control, inappropriate TV programs, VCR recordings, and DVD content can be blocked. When someone attempts to watch a blocked program or content, the flat panel TV displays the password window. Parental Control applies to both analog and digital material.

To ensure that your blocks are not removed in error, the flat panel TV requires a password to change access to blocked programs, channels, or content. The default password for your panel is 1234 changing the password to a four-digit code that is meaningful to you.

Follow the steps below to change the password.

1 ) Access the

System Setup

through the

Setup

. We strongly recommend

“3.5.3

2 ) Select

3 ) Enter the current four-digit code using the 0 through 9 buttons.

Change Password

from the System Setup menu.

Please Input Your Passwor d.

A confirmation message appears on screen.

4 ) Enter your new password. 5 ) Enter your new password a second time when prompted. 6 ) Press HOME MENU to exit the menu.

Write your new password:

If you forget your password: When “Please Input Your Password” appears at Step 4, press and hold the

ENTER

for three or more seconds. The password reverts to the default password, 1234.

button

Basic Operations For Television Viewing

The lock symbol here marks

blocked TV ratings.

3.5.2 Activate Parental Control

The Parental Control function must be active for the panel to block content. If this option is turned Off, blocked programs appear on screen. To activate Parental Control blocking, follow the steps below.

1 ) Access the

System Setup

through the

Setup.

2 ) Select

Parental Control.

The password entry screen appears.

3 ) Enter your four-digit code using the 0 through 9 buttons. 4 ) Select

Status.

Status : Off MPAA Ratings TV Parental Guidelines Canadian English Ratings Canadian French Ratings Unavailable Ratings : View Digital Regional Ratings

5 ) Select On to activate Parental Control. 6 ) Press HOME MENU to exit the menu.

When a program is blocked, a (B) appears in appropriate rating boxes. If a channel is blocked but the Parental Control system is turned off, the symbol is a (V) and the channel/program is viewable.

FV D B B B

3.5.3 Assign a Rating System to Create Blocks

Besides choosing to block certain channels, you may use one of the recognized rating systems to block programs and/or content. Your panel recognizes the following rating systems:

•TV ratings

• TV Parental Guidelines including unrated programming

• Motion Picture Association of America (MPAA for movies)

• Canadian English/French rating systems

Note: Your flat panel TV ships with all ratings unblocked.

To block TV or other content using a rating system, follow the steps below.

1 ) Access the 2 ) Select

System Setup

Parental Control

3 ) Select one of the rating systems from the submenu.

through the

Setup.

from the System Setup menu.

Basic Operations For Television Viewing

MPAA Ratings menu TV Parental Guidelines menu

N/A : View G : View PG : View PG-13 : View R : View NC-17 : View NR : View

TV-None TV-Y TV-Y7 TV-G TV-PG TV-14 TV-MA

B B B V V V V

Canadian English Ratings menu Canadian French Ratings menu

E : View C : View C8+ : View G : Block PG : Block 14+ : Block 18+ : Block

E : View G : View 8 ans+ : View 13 ans+ : View 16 ans+ : View 18 ans+ : View

Unavailable Ratings menu Digital Regional Ratings menu

Status : Off MPAA Ratings TV Parental Guidelines Canadian English Ratings Canadian French Ratings Unavailable Ratings : View Digital Regional Ratings

FV D L S V

VVV

V V

V V V

4 ) Use the arrow buttons to highlight a block level for that rating system. 5 ) Press ENTER to reverse the blocked status for the highlighted TV Parental Guideline option.

A block (B) or view (V) symbol appears in appropriate rating boxes. For other rating options, press

/

toggle between block and view.

6 ) Press HOME MENU to exit the menu.

When a rating is blocked, all more severe ratings are blocked as well. For example, blocking TV rating TV-PG (Parental guidance suggested) automatically blocks TV-14 (Parents strongly cautioned) and TV-MA (Mature audiences only). In turn, unblocking a rating causes less severe ratings to become automatically available.

Program Rating of “None”

The flat panel TV also provides a rating setting that blocks programs with a rating of

None

Guidelines Rating system identifies programs with a

None

are as follows:

rating level. Examples of programs with a rating of

None

. The US TV Parental

• Emergency Bulletins (such as EAS messages, weather warning and others)

• Locally originated programming

• Public Service Announcements

•News

• Politics

• Religion

•Sports

Basic Operations For Television Viewing

To block a program with a rating of

1 ) Access the 2 ) Select 3 ) Select 4 ) Select 5 ) Select an option ( 6 ) Press HOME MENU to exit the menu.

Refer to “8.1 Ratings Charts (for Various Audience Classifications)” for detailed information about the different rating systems.

Block Not Rated Programs

With some TV programs, the rating information is unavailable. To block these programs, follow the steps below.

1 ) Access the 2 ) Select 3 ) Select 4 ) Select an option ( 5 ) Press HOME MENU to exit the menu.

System Setup

Parental Control

from the System Setup menu.

TV Parental Guidelines TV-None

from the submenu.

View

System Setup Parental Control from Unavailable Ratings

View

None

, follow the steps below.

through the

from the Parental Control menu.

Block

through the

the System Setup menu.

from the Parental Control menu.

Block

Setup

Note: Your flat panel TV ships with this option set to View.

New Ratings System for Digital Broadcasts

Some Digital broadcasts carry new ratings that are not compatible with the panel’s original Parental Control settings. When first tuning to one of these broadcasts, the Digital Regional Ratings menu appears on screen. Change the Parental Control settings to handle the new ratings. Otherwise, previous blocked ratings may become unblocked.

Note: Adding the new rating does not cause programs with this rating system to be blocked automatically.

To add the new rating system to your panel, follow the directions below.

1 ) Access the 2 ) Select 3 ) Select

Parental Control Digital Regional Ratings

System Setup

through the

from the System Setup menu.

from the submenu.

Setup.

A list of available ratings appears.

4 ) Select from the available ratings. 5 ) Select a level from the available ratings. 6 ) Select 7 ) Press HOME MENU to exit the menu.

View

Block

Basic Operations For Television Viewing

Delete a New Ratings System

If an added ratings system is no lon ger needed, delete the ratings system from your flat panel TV. It is unnecessary to remove blocks from individual channels or programs. Deleting the ratings line removes any/all blocks initiated with that system.

1 ) Access the

System Setup

through the

Setup.

2 ) Select 3 ) Select 4 ) Select

Parental Control

from the System Setup menu.

Digital Regional Ratings RRT Reset

to delete the new ratings system from the flat panel TV.

from the submenu.

The message “Reset digital regional ratings?” appears.

5 ) Select 6 ) Press HOME MENU to exit the menu.

While the Parental Control menu is open, the status display remains unchanged even if the system receives broadcasts carrying new ratings.

OK.

3.5.4 Temporarily Remove a Block

The password entry screen appears when detecting the blocked rating signals (with the picture and sound turned off). Entering your four-digit password allows you to view the program until your flat panel TV is placed into Standby or turned Off. To temporarily remove a block, follow the steps below.

1 ) Tune the flat panel TV to the blocked channel. 2 ) Wait for the Block message to appear on screen. 3 ) Enter the four-digit password.

The password window appears. When a four-digit password is entered, or no operation is performed within 60 seconds, the window disappears. To recall the window after it disappears, change the channel or input source then return before repeating the above steps.

Please Input Your Passwor d.

For INPUT 2 (except 480i signals) and INPUT 4 through INPUT 7, the password entry screen appears when is selected from the Unavailable Ratings menu.

Block

Basic Operations For Television Viewing

The TOOLS Menu provides short-cuts to the selectable menu options while watching a program.

3.6 Smart Starts for New Owners

Many of the flat panel TV features make it easy to use but also environmentally friendlier. This section explains how to extend the life of your panel while being energy efficient. We suggest applying all of the following functions below for the simplest usage, best quality, and longest life span.

3.6.1 Use the TOOLS Menu

To change the current menu to another option, the on-screen TOOLS Menu provides short-cuts to the available selections even while watching a program. To display the menu, press TOOLS on the remote control. The menus shown in this section differ, depending upon the menu.

EXIT

SAT GUIDE

DVD

TOP MENU

HOME MENU

SAT / DVD MENU

ENTER

TOOLS

RETURN

TELEVISION TOOLS

Sound

Random

All Play Mode : Single

A-B Repeat

Time Search

Repeat

Use the arrow buttons to toggle between options. The setting is complete as soon as the selected option appears in the center of the screeen. When showing two screens, the TOOLS Menu appears on the main screen.

3.6.2 Extend Your Panel Life

This function provides short-cuts to your panel’s longer service life. Your flat panel TV includes the Screen Protection option. Activating this option causes the panel to automatically select the several different features that can prolong the life of your panel and help alleviate after-image ghosts or burn-in. To set this option, follow the steps below.

1 ) Access the 2 ) Select

Screen Protection

through the

Setup.

from the Option menu.

Option

A confirmation screen appears.

3 ) Select

Yes

from the submenu.

The following settings are automatically entered:

•Auto Size: Wide-Zoom

•Side Mask - Detection: Mode 1

•Orbiter (AV source): Mode 1

•Orbiter (PC source): Mode 1

•Energy Save: Mode 1

4 ) Press HOME MENU to exit the menu.

Basic Operations For Television Viewing

3.6.3 Turn On the Image Orbiter

A built-in feature to protect against burn-in is the Orbiter function. Orbiter automatically changes the position of the picture imperceptibly while the image is on screen. To activate the Orbiter, follow the steps below. To cancel this function, select Off in Step 3.

Option

1 ) Access the

through the

Setup.

2 ) Select 3 ) Select

Orbiter from the Option menu. Mode 1

Mode 2.

• AV source Mode 1: for any screen mode except Dot by Dot

• AV source Mode 2: for all available screen modes

•PC source Mode 1: to enable the Orbiter

• PC source Mode 2: to smooth the text/character appearance

4 ) Press HOME MENU to exit the menu.

Note: The farthest edges of an image may be hidden at times as the picture position shifts. Also, when the Orbiter

function is set to Mode 1 or Mode 2, the image may appear to drop slightly on the screen.

3.6.4 Trigger the Screen-Saving Video Pattern Periodically

The Video Pattern function causes the screen to appear white, which helps to alleviate after-image ghosts or burnin. While the Video Pattern screen is on, only the remote’s TV (a) button and the panel’s STANDBY/ON button is available. The panel automatically switches to Standby one hour after running the Video Pattern screen. To cancel the Video Pattern screen, press the remote’s TV (a) or the panel’s STANDBY/ON.

To activate the Video Pattern screen, follow the steps below.

Option

1 ) Access the 2 ) Select

Video Pattern

through the

from the Option menu.

Setup.

A confirmation screen appears.

3 ) Select

Start

from the submenu.

The Video Pattern screen appears.

4 ) Leave the panel alone for a minimum of one hour.

Note: The Video Pattern timer has priority over Sleep Timer, No Signal off, and No Power off (Power Management)

settings.

3.6.5 Activate Energy Save to Reduce Power Usage

The Energy Save option decreases picture brightness and lowers power consumption. The recommended setting, Energy Save Mode 1, extends the life of your panel while keeping power usage at a minimum.

Follow the steps below to activate an Energy Save option.

1 ) Access the 2 ) Select 3 ) Select an option from the Energy Save submenu.

4 ) Press HOME MENU to exit the menu.

Power Control

Energy Save

Off No effect Mode 1 consumes less power than Off Mode 2 consumes less power than Mode 1

from the menu.

Option Description

through the

Setup.

Additional Picture and Sound Adjustment Options

4 Additional Picture and Sound Adjustment

Options

To take advantage of all that your flat panel TV offers, browse this chapter for features and functions that enhance your viewing experience. Most sections deal with adjusting the picture and arranging screen/menu items while the remaining sections provide sound and power management options. Apply as many or as few of these changes as desired.

4.1 Choose an AV Option (Video, Game, etc.)

Similar to the purpose for the room light sensor, the AV Option or Selection depends upon the brightness of the environment and the program or movie on screen. Images can be from either an AV Source or from a PC. Both sources are discussed below.

Choose from among the seven AV Selections for the best image from an external AV Source. Use either the remote control or the Home Menu to select the AV source. For a PC, skip down to “4.1.3 Choose a PC Source.”

If the AV source is a Game Control, select GAME and refer to “4.1.4 Set the Panel to Recognize a Game Console” for more information.

4.1.1 AV Source through the Remote Control

Follow the directions below to set an AV Selection for an external AV Source using the remote control.

1 ) Press AV SELECTION on the remote control.

The current AV selection appears.

2 ) Press AV SELECTION again before the displayed mode disappears.

Each press cycles the options in the order shown below.

AV Selection

OPTIMUM automatically adjusts the image quality for the

brightness level of the viewing area (shared by external input and TV input sources)

PERFORMANCE for a highly defined image in a normally bright

room (shared by external input and TV input sources)

PURE reflects input signals as faithfully as possible for

checking image materials, for example (shared by external input and TV input sources)

MOVIE for movies (shared by external input and TV input

sources)

SPORT for sports programs (shared by external input and

TV input sources)

GAME lowers image brightness for easier viewing (shared

by external input and TV input sources)

Description

Standard allows customizing settings as desired (set the

mode for each input source)

3 ) Allow the AV Selection screen to disappear.

When the screen disappears, the panel locks in last viewed option and the menu closes.

When OPTIMUM is selected,

images are adjusted automatically

based on the information collected

at the Room Light Sensor, as well

as the Color Sensor (when in use).

Additional Picture and Sound Adjustment Options

4.1.2 Choose an AV Source through the Home Menu

The other method for choosing an AV Selection uses the Home Menu. Follow the directions below to set an AV Selection for an external AV Source.

The AV Selection, OPTIMUM, automatically adjusts to the highest image quality possible for the selected source and viewing environment. Your flat panel TV employs advanced sound reproduction technologies, such as SRS WOW HD gradual so changes to the tint and brightness may be visible. This is normal and is not a malfunction.

To choose an AV source through the Home Menu, follow the steps below.

1 ) Access the

, OPTIMUM also automatically adjusts to the optimum sound for the selected scene. This process is

Picture

through the

Setup.

2 ) Select

AV Selection

from the Picture menu.

3 ) Select an option from the submenu.

AV Selection

OPTIMUM PERFORMANCE PURE MOVIE SPORT GAME Standard

AV Selection : OPTIMUM PureCinema Sound Control : Off OPTIMUM Performance Reset

Picture

(Submenu when OPTIMUM is selected for AV Selection)

4 ) Press HOME MENU to close and exit the menu.

4.1.3 Choose a PC Source

From a PC, choose between the two AV Selections for the best image. The options are as follows:

• STANDARD: for a highly defined image in a normally bright room

• USER: allows customizing settings as desired for each input source

Additional Picture and Sound Adjustment Options

4.1.4 Set the Panel to Recognize a Game Console

When adding a game console to your flat panel TV, use the Game function to establish a preference for image quality or for operability.

To have the panel store your Game preference, follow the steps below.

Option

1 ) Access the

through the

Setup.

2 ) Select 3 ) Select 4 ) Press HOME MENU to exit the menu.

To activate the Game Control Pref option, set the AV Selection to GAME and use an external input (unless the source is coming from a PC). When a PC source menu is on screen, the Also, the in Multi-Screen”) or image freezing

Game Control Pref On

(operability preferred) or

Game Control Pref

from the menu.

Off

(image quality preferred).

Game Control Pref

option for operability (on) is ignored during multi-screen viewing (refer to “4.4 View

(refer to “4.5 Freeze the Picture”).

option is ignored.

4.2 Adjust Specific Picture Elements

Plasma technology delivers one of the best images available today. However, the viewing area/environment and personal preferences affect how the picture appears. This section provides methods to adjust the picture and sound for your best viewing experience.

4.2.1 Choose a Screen Size (Automatically or Manually)

Automatic Screen Sizing

The flat panel TV can automatically select an appropriate screen size for the incoming video signal from a connected HDMI device. To allow automatic screen sizing, follow the steps below.

Option

1 ) Access the 2 ) Select 3 ) Select

Auto Size Natural

through the

from the Option menu.

Wide-Zoom

Setup.

from the submenu.

Option Description

Off deactivates the Auto Size function Natural adjusts the image to the screen size Wide-Zoom enlarges and displays only the 4:3 aspect ratio

portion in full and wide screen

4 ) Press HOME MENU to exit the menu.

Note: When a video signal contains no aspect ratio information, the Automatic Screen Size function is unavailable.

Additional Picture and Sound Adjustment Options

Manual Screen Sizing

Manually select an appropriate screen size if an image fails to appear in the correct format. Browse the menu for the correct screen size for a specific program.

The selectable screen sizes differ depending on the types of input signals. While watching a TV broadcast, press SCREEN SIZE on the remote control to cycle the picture through Auto, FULL, Dot by Dot, ZOOM, CINEMA, 4:3, WIDE, WIDE 1 and WIDE 2. Freely change the screen size during broadcasts or video from other input sources. Auto is available when receiving HD broadcasts.

The following chart provides information about how the screen appears for each option.

AV Option Description

Auto adds side masks or displays the image in full

screen when detecting HD pictures containing side

masks. See Detect Masks on page 62. FULL squeezes 16:9 images Dot by Dot

ZOOM bars may appear on the top and bottom on some

CINEMA bars may appear on the top and bottom on some

4:3 side bars appear on each side WIDE pictures progressively stretch toward each side

WIDE 1 pictures progressively stretch toward each side

WIDE 2 pictures evenly stretch toward each side (available

PC Option Description

4:3 fills without altering the input signal aspect ratio FULL shows 16:9 screen display

With WIDE 1 or WIDE 2 selected, a High Definition (HD) TV broadcast may crop part of an image or menu. If an image or menu appears cut or runs off the screen, change the option to FULL.

Avoid showing signals that fill only part of the screen. Images that fail to fill the screen may cause temporary or permanent image retention depending on the frequency and duration. For example, an HD broadcast with side masks (4:3 content) causes uneven wear of the plasma cells. If side masks appear around a broadcast, after that program or movie is over, switch to a full screen motion video. This action helps the panel balance wear for the plasma cells and guard against after-image issues. For more information about Masks, refer to “4.3.1 Adjust for Screen Masking (black bars on sides).”

matches input signal to the same number of screen

pixels (available for 1080i or 1080p signals only)

programs that are 16:9 letterbox

programs that are 14:9 letterbox (available for SD

signals only)

(available for SD signals only)

(available for HD signals only)

for HD signals only)

Note: Not all broadcast programs carry alternative screen sizes.

Additional Picture and Sound Adjustment Options

4.2.2 Correct the Picture for an AV or PC Source

Although picture adjustments are to your personal preferences, often the source causes unanticipated image changes. Your flat panel TV offers several adjustment options.

AV Source

Option Left Arrow Right Arrow

Contrast less contrast more contrast Brightness dimmer brighter Color decreased intensity increased intensity Tint purplish skin tones greenish skin tones Sharpness softer definition crisper definition

PC Source

Option Left Arrow Right Arrow

Contrast less contrast more contrast Brightness dimmer brighter

Red weaker color stronger color Green weaker color stronger color Blue weaker color stronger color

To correct the picture for an AV or a PC source, follow the steps below.

1 ) Access the

through the

Setup.

Picture

2 ) Select an option to adjust.

AV Source PC Source

Picture

AV Selection : PERFORMANCE Contrast : 40 Brightness : 0 Color : 0 Tint : 0 Sharpness : 0 Pro Adjust Reset

AV Selection : STANDARD Contrast : 40 Brightness : 0 Red : 0 Green : 0 Blue : 0 Reset

3 ) Select the desired level for that option using the left/right arrows (/).

Picture

Contrast

4 ) Repeat the process for any additional adjustments. 5 ) Press HOME MENU to exit the menu after all adjustments are complete.

Note: Reset returns all settings to the factory defaults.

Additional Picture and Sound Adjustment Options

4.3 Assign Advanced Picture Functions

Your flat panel TV provides various advanced functions for optimizing the picture quality that go beyond the basic adjustments explained earlier in this manual. This section explores the value offered through Pioneer’s Pro Adjust High Definition (HD) support, top quality blacks, better balanced whites, and overall color improvements.

4.3.1 Adjust for Screen Masking (black bars on sides)

Screen Masks fill areas on both sides of a picture. Some content fails to fill the screen so bars appear on each side of the picture. This section explains how to adjust screen masking.

Detect Masks

Some HD broadcasts transmit in 4:3 content with side masks. Side masks are black bars that appear on the picture’s left and right sides. If the flat panel TV’s Screen Size is set to Natural during the Auto Size process, gray bars replace the black bars. When the panel is set to Wide-Zoom, the bars are hidden. These responses reduce after-image concerns.

To allow the panel to detect side masks, follow the steps below.

Option

1 ) Access the

through the

Setup.

2 ) Select 3 ) Select 4 ) Select

Side Mask Detection Mode 1

from the Option menu.

from the submenu.

Mode 2

to activate Side Mask Detection.

Mode 1 detects only black side masks and Mode 2 detects both black and illustrated side masks. Select Off to deactivate this function.

5 ) Press HOME MENU to exit the menu. 6 ) Confirm that the word “AUTO” appears in the InfoBanner.

Video signals can affect the Side Mask Detection function differently. For High Definition broadcasts, if Side Mask Detection is on, the panel automatically detects images containing side masks and shows the picture in full screen. Cycle the screen size to select Auto for video signals without aspect ratio information.

Video content also can affect the Side Mask Detection function. If a detection error occurs when trying to watch HD content, manually change the screen size to the proper setting for the content.

HD Wide Mode

The HD Wide Mode allows selecting the display mode (WIDE 1 or WIDE 2) when detecting side masks that appear in a 4:3 image. This option is available when the Auto Size menu is set to Wide-Zoom and Side Mask Detection to Mode 1 or Mode 2. To allow the HD Wide Mode, follow the steps below.

Option

1 ) Access the 2 ) Select 3 ) Select

Side Mask HD Wide Mode

through the

from the Option menu.

from the submenu.

Setup.

4 ) Select

Mode 1

Mode 2

to activate HD Wide Mode.

• Mode 1: screen mode sets to WIDE 1 when detecting side masks.

• Mode 2: screen mode sets to WIDE 2 when detecting side masks.

5 ) Press HOME MENU to exit the menu.

Additional Picture and Sound Adjustment Options

Lighten Side Masks

If content appears with bars (side masks) on each side of a picture when the screen size is 4:3 and Side Mask Detection is set to Mode 1 or Mode 2, the bars automatically change from black to gray. However, the gray is fairly dark. To change the bars to a lighter shade of gray, follow the steps below.

Option

1 ) Access the

through the

Setup.

2 ) Select 3 ) Select 4 ) Select the desired parameter.

5 ) Press HOME MENU to exit the menu.

Side Mask Brightness Sync.

Fixed sets the same brightness for gray side masks Auto adjusts the side mask brightness according to the

from the Option menu.

from the submenu.

Parameter Description

brightness of screen images

4.3.2 Select a PureCinema Level for High Quality Image

Pioneer’s PureCinema automatically detects and analyses a film-based source (originally encoded at 24 frames/ second) then recreates each still film frame for HD picture quality. The function supports both film and text material.

To set the PureCinema level for your HD material, follow the steps below.

Picture

1 ) Access the

through the

Setup. With AV Selection set to OPTIMUM, go to Step 2. With AV Selection set to any options other than OPTIMUM, select Pro Adjust then go to Step 2.

2 ) Select

PureCinema

from the submenu. 3 ) Select 4 ) Select the desired parameter.

Film Mode

Film Mode Off deactivates PureCinema

Text Off deactivates text optimization Optimization On improves subtitle display

Text Optimization

Mode Parameter Description

Standard (not available for input signals 480p, 720p @60 Hz, or 1080p @60 Hz)

Smooth (not available for input signals 1080p @60 Hz)

Advance (not available for input signals 1080p @60 Hz)

depending on the material.

automatically detects recorded image data when displaying DVD or high-definition images (e.g., movies) having 24 frames per second for smooth and vivid playback

produces smoother and more vivid moving images

converts theatre-quality images to 72 Hz when displaying DVD images (e.g., movies) having 24 frames per second for smooth and vivid playback

quality

Additional Picture and Sound Adjustment Options

5 ) Press HOME MENU to exit the menu.

Note: Activating the Game Control Pref setting under the Option menu disables the PureCinema setting.

4.3.3 Select an Intelligent Mode Option

Use this function to optimize color tones and brightness for images.

To select the Intelligent Mode, follow the steps below.

1 ) Access the

Picture

through the

Setup.

2 ) Select 3 ) Select 4 ) Select 5 ) Select the desired parameter.

6 ) Press HOME MENU to exit the menu.

Pro Adjust Intelligent Mode Mode 1

Off No effect Mode 1 compensates for more effective picture adjustment Mode 2 compensates for appropriate picture adjustment

from the Picture menu.

from the submenu.

Mode 2

Parameter Description

(or Off).

Note: As this function automatically optimizes image quality, this process is gradual so changes to the tint and

brightness may be visible. This is normal and is not a malfunction.

4.3.4 Select the Picture Detail Options

The Picture Detail function provides five adjustment options: DRE Picture, Black Level, ACL, Enhancer Mode and Gamma for enhanced image contrast, sharpness and image gradation characteristics.

To select the Picture Detail options, follow the steps below.

1 ) Access the

Picture

through the

Setup.

2 ) Select 3 ) Select 4 ) Select 5 ) Select the desired parameter.

Pro Adjust Picture Detail

from the Picture menu.

from the submenu.

DRE Picture, Black Level, ACL, Enhancer Mode

Option Parameter Description

DRE Picture (emphasizes image contrast between brightness and darkness)

Black Level (emphasizes dark portion of images for enhanced contrast)

ACL (compensates images for optimum contrast characteristics)

Gamma.

Off No effect High enhances DRE picture Mid standard DRE picture Low moderate DRE picture Off No effect On activates Black Level

Off No effect On activates ACL

Additional Picture and Sound Adjustment Options

Option Parameter Description

Enhancer Mode (selects processing of the image’s high frequency (detailed) area)

Gamma (adjusts the gamma characteristics)

6 ) Press HOME MENU to exit the menu.

1 selects Hard (SHARPNESS)

2 selects Natural (SHARPNESS)

3 selects Soft (SHARPNESS)

1 selects gamma

2 selects gamma

3 selects gamma

4.3.5 Adjust the Color Temperature

Adjust the Color Temperature for better white balance.

To set the color temperature level, follow the steps below.

Picture

1 ) Access the

through the

Setup.

image

characteristics 1

characteristics 2

characteristics 3

2 ) Select 3 ) Select 4 ) Select 5 ) Select the desired parameter.

To make fine adjustments, select Manual, press and hold ENTER for more than three seconds. The “Manual adjustment” screen appears. Go to Step 6.

Pro Adjust Color Detail Color Temp

High white with bluish tone Mid-High intermediate tone between High and Mid Mid natural tone Mid-Low intermediate tone between Mid and Low Low white with reddish tone Manual adjusts to your preference

from the Picture menu.

from the Pro Adjust menu.

from the submenu.

Parameter Description

Additional Picture and Sound Adjustment Options

6 ) Select the desired item.

Item Left Arrow Right Arrow

R High (fine adjustment for G High weaker green stronger green B High weaker blue stronger blue R Low (fine adjustment for dark G Low weaker green stronger green B Low weaker blue stronger blue

To adjust another item, press

7 ) Press HOME MENU to exit the menu.

bright portions)

portions)

RETURN

then repeat Steps 5 and 6.

weaker red stronger red

4.3.6 Use CTI and Color Space

Use the Color Transient Improvement (CTI) and Color Space options to further enhance the picture to your preference.

To set the CTI and Color Space options, follow the steps below.

1 ) Access the 2 ) Select 3 ) Select 4 ) Select

Pro Adjust Color Detail CTI

Picture

through the

from the Picture menu.

from the Pro Adjust menu.

Color Space

Setup.

from the submenu.

5 ) Select the desired parameter.

Option Parameter Description

CTI Off No effect

On activates CTI

Color Space 1 optimized for vivid, vibrant color reproduction

2 standard color reproduction

6 ) Press HOME MENU to exit the menu.

4.3.7 Use the Color Management

Use the Color Management option to fine adjust the coloring of images.

To set the Color Management option, follow the steps below.

1 ) Access the 2 ) Select 3 ) Select 4 ) Select

Pro Adjust Color Detail Color Management

Picture

through the

from the Picture menu.

from the Pro Adjust menu.

Setup.

from the submenu.

Additional Picture and Sound Adjustment Options

R0 Y0 G0 C0 B0 M0

Color Management

5 ) Select the desired parameter.

6 ) Select the desired level.

Item Left Arrow Right Arrow

R closer to magenta closer to yellow Y closer to red closer to green G closer to yellow closer to cyan

C closer to green closer to blue B closer to cyan closer to magenta M closer to blue closer to red

To adjust another item, press

RETURN

then repeat Steps 5 and 6.

7 ) Press HOME MENU to exit the menu.

4.3.8 Reduce Noise from the Image

Use the video noise reduction features for clear and crisp images. Refer to the following table for available noise reduction functions.

To select the Noise Reduction options, follow the steps below.

Picture

1 ) Access the 2 ) Select 3 ) Select 4 ) Select

Pro Adjust Noise Reduction 3DNR, Field NR, Block NR

through the

from the Picture menu.

from the Pro Adjust menu.

Setup.

Mosquito NR.

Additional Picture and Sound Adjustment Options

5 ) Select the desired parameter.

Option Parameter Description

3DNR (3-dimensional Noise Reduction)

Field NR (removes glimmer for more natural image)

Block NR (reduces noise in HD images)

Mosquito NR (reduces mosquito noise in DVD and HD images)

6 ) Press HOME MENU to exit the menu.

Off No effect High enhances DNR Mid standard DNR Low moderate DNR Off No effect High enhances Field NR Mid standard Field NR Low moderate Field NR Off No effect On activates Block NR Off No effect On activates Mosquito NR

4.3.9 Adjust Color Signals

The 3DYC function optimizes characteristics for separating brightness signals and color signals while the I-P Mode provides optimum conversion from interlace signals to progressive signals. Use these options to adjust color signals for both video and still images.

To select the 3DYC and I-P Mode options, follow the steps below.

1 ) Access the 2 ) Select 3 ) Select 4 ) Select 5 ) Select the desired parameter.

6 ) Press HOME MENU to exit the menu.

Picture Pro Adjust Others 3DYC

3DYC Off No effect

I-P Mode 1 optimizes video images

through the

from the Picture menu.

from the Pro Adjust menu.

I-P Mode.

Option Parameter Description

Setup.

High enhances 3DYC Mid standard 3DYC Low moderate 3DYC

2 standard setting 3 optimizes still images

Notes: 3DYC is available when connected to only the video terminal at INPUT 1, INPUT 2 or INPUT 3 or when

analog tuner is selected. I-P Mode is unavailable when the selected mode is On for Game Control Pref or when input signal is 480p, 720p or 1080p.

Additional Picture and Sound Adjustment Options

2-Screen

Picture-in-Picture (P-in-P)

4.4 View in Multi-Screen

The flat panel TV can show multiple screens at the same time; two-screen or picture-in-picture. The pictures may be reversed (in 2-screen and P-in-P) or moved to various locations on the screen (P-in-P).

4.4.1 Split/Swap/Shift the Screen

To split the screen so that two channels appear, press the SPLIT button on the remote control. Each press of the button cycles the screen through two-screen, picture-in-picture, and single-screen views.

To switch the images between screen sides/locations, press the SWAP button.

To move the Picture-In-Picture (P-in-P) small image counter-clockwise, press the SHIFT button.

Press SPLIT to cycle through the different multi-screen views. Press SWAP

to switch the position of the two screens. Press SHIFT

to move the position of

the small screen counter-clockwise.

Warning: Displaying pictures in multi-screen mode for an extended period may cause an after-image.

Additional Picture and Sound Adjustment Options

INPUT

DISPLAY

SWAP

TV/DTV

SCREEN

SIZE

SHIFT

SPLIT

SELECTION

FREEZE

The multi-screen function is unavailable when viewing source from a single input or from two

external

sources.

To return to a single picture, press EXIT. Another option is to select a multi-screen mode from the TOOLS Menu. To select a multi-screen mode, follow the

steps below.

1 ) Press TOOLS.

The TOOLS Menu appears on screen.

2 ) Select

Split, Swap

Shift

from the menu.

Use the arrow buttons to highlight an option (then press

ENTER

if you select Swap).

3 ) Select a mode.

Select Off, 2-screen or P-in-P for the Split mode. The selected mode is displayed in the center of the TOOLS Menu.

4.5 Freeze the Picture

During fast-action sequences or detailed pictures, try capturing the image with the FREEZE option. FREEZE allows you to better understand the action or picture details if desired. To freeze a picture from a TV broadcast or movie, follow the steps below.

input

1 ) Press FREEZE to create a still image picture

(copy) of the currently showing image.

The copy appears to the right of the still-moving video sequence thus splitting the screen.

2 ) Press FREEZE again to release the image.

The frozen image disappears, returning the picture to a single screen with the video sequence still in progress.

• With the screen split, an image cannot be frozen. A warning message appears if you attempt to use this function when there is already a frozen

image on screen. If an image is left frozen on the screen, the panel automatically releases the image after five minutes.

Note: Using FREEZE for an extended period may cause an after-image.

SPLIT

INPUT

DISPLAY

SELECTION

FREEZE

SWAP

TV/DTV

SCREEN

SIZE

SHIFT

Additional Picture and Sound Adjustment Options

4.6 Use the Banner Feature

When tuning in a TV channel or an input signal changes, any available information appears on the screen if the signal carries information about the program (see InfoBanner below). Pressing DISPLAY causes the InfoBanner (additional) to appear. Press EXIT or DISPLAY again to hide the banner.

InfoBanner

00001.000 ABCDEFGH

132456

XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX

STEREO 9:30AM

InfoBanner (additional)

D00001.000 ABCDE

1 -Broadcast signal (Digital/Analog) 2 -Channel number 3 -Station name 4 -Program title 5 -Sound multiplex information 6 -Current time

XXXXXXXXXXXXXXXXXXXXXXXXXXXXX

7:07PM-8:08PM

7 8 9 11 1210

7 -Program time schedule 8 -Parental Control information

9 -Parental icon 10 -Parental name 11 -Signal information (HD/SD) 12 -Favorite icon

STEREO

PRT_10

9:30AM

HDV

A separate banner also appears at the bottom of the screen showing the AV Selection mode (bottom left) and screen size (bottom right).

The above information is only appears if it is included in the broadcast signal. During multi-screen mode, the banner appears in both main and sub screens.

Additional Picture and Sound Adjustment Options

4.7 Select Alternatives for/to Sound

There are four sound alternatives for your flat panel TV; CC, MTS, SAP, and Sound Effect. This section defines each of these alternatives then explains how/when to use.

4.7.1 Activate Closed Captioning (CC)

Your flat panel TV is equipped with an internal closed caption (CC) decoder. CC allows conversations, narration, and sound effects in TV programs and home videos to appear as subtitles on the screen. For digital channels, some parameters can be changed such as the text font and color. However, not all programs/videos offer closed caption. Please look for the “ “ symbol to confirm that the channel or program provides closed captioning.

To activate closed captioning when available, follow the steps below.

1 ) Access the

System Setup

through the

Setup.

2 ) Select 3 ) Select 4 ) Select an option.

5 ) Press HOME MENU to exit the menu.

Types of Closed Caption

Broadcast TV offers different types of closed captioning. Your flat panel TV provides support for the recognized types on Analog programming as well as Digital signals that carry analog closed captions.

• CC 1, CC 2, CC 3, or CC 4: provides subtitles with a full view of the picture

• Text 1, Text 2, Text 3, or Text 4: superimposes other information (e.g. weather) that is independent of the TV

To change the closed caption type from the default CC 1, follow the steps below.

1 ) Access the

Closed Captions Status

from the submenu.

Parameter Description

Off does not show closed captioning (default) On shows closed captioning when available On If Mute shows closed captions only while sound is muted

program in progress

System Setup

from the System Setup menu.

through the

Setup.

2 ) Select 3 ) Select 4 ) Select the desired closed caption.

5 ) Press HOME MENU to exit the menu.

Closed Captions Analog Settings

from the System Setup menu.

from the submenu.

Status : Off Analog Settings : CC 1 Digital Settings

Additional Picture and Sound Adjustment Options

Closed Caption for Digital Programs

There are six different closed caption options for digital programming, called Service levels. The Primary Caption Service is on Service 1 and the Secondary Language Service is on Service 2. More information about these offerings is found later in this chapter.

To change the digital closed caption from the default Service 1, follow the steps below.

1 ) Access the

System Setup

through the

Setup.

2 ) Select 3 ) Select 4 ) Select

Closed Captions Digital Settings Digital Service

from the System Setup menu.

from the submenu.

5 ) Select the desired closed caption service level (/).

Digital Settings

Digital Service : Service 1 Font Size : Auto Font : Auto Font Color : Auto Font Opacity : Auto Background Color : Auto Background Opacity : Auto

6 ) Press HOME MENU to exit the menu.

To change the appearance of closed captioning on a digital program, follow the steps below.

1 ) Access the 2 ) Select

System Setup

Closed Captions

through the

Setup.

from the System Setup menu.

3 ) Select

Digital Settings

from the submenu. 4 ) Select an option to change. 5 ) Select the desired parameter for that option.

The default parameter for each option is Auto.

Option Description

Font Size Auto, Large, Standard, Small

Font

Auto, Font 1, Font 2, Font 3, Font 4, Font 5, Font 6, Font 7

Font Color Auto, Black, White, Red, Green, Blue, Yellow,

Magenta, Cyan Font Opacity Auto, Solid, Transparent, Translucent, Flashing Background Color Auto, Black, White, Red, Green, Blue, Yellow,

Magenta, Cyan Background Opacity Auto, Solid, Transparent, Translucent

Font 1 (monospaced with serifs)/ Font 2 (proportionally spaced with serifs)/ Font 3 (monospaced without serifs)/ Font 4 (proportionally spaced without serifs)/ Font 5 (casual font)/ Font 6 (cursive font)/ Font 7 (small capitals font)

6 ) Press HOME MENU to exit the menu.

STEREO SAP MONO

STEREO mode SAP mode MONO mode

STEREO signals STEREO + SAP MONO + SAP MONO signals

Additional Picture and Sound Adjustment Options

4.7.2 Switch Languages Using MTS

Multi-channel Television Sound (MTS) allows switching the audible language if it is available for that program. Available languages differ depending on the current broadcast.

When watching a digital TV program that provides multi language services, follow the steps below.

1 ) Press TOOLS on the remote control.

The TOOLS Menu appears on screen.

EXIT

DVD

TOP MENU

HOME MENU

SAT GUIDE

TOOLS

ENTER

RETURN

2 ) Select 3 ) Select

MTS

from the TOOLS Menu.

English, Français

Español.

SAT / DVD MENU

A digital TV program without sound or language information causes “N/ A” to appear on the screen. For languages other than English, French, or Spanish, the word “Others” appears instead. If the selected language is available when the channel or program is changed, that language is heard.

4.7.3 Select SAP

When watching TV programs on the VHF/UHF frequencies or from analog cable TV channels, the TOOLS button can activate Stereo Sound and/or Secondary Audio Programs (SAP) if available.

To select Stereo/SAP options, follow the steps below.

1 ) Press TOOLS.

The TOOLS Menu appears on screen.

2 ) Select 3 ) Select

MTS

from the TOOLS Menu.

STEREO, SAP

MONO.

The chart below breaks down the Stereo/SAP options.

STEREO mode SAP mode MONO mode

STEREO SAP MONO

STEREO 9:30AM STEREO (SAP) 9:30AM MONO (SAP) 9:30AM MONO 9:30AM

In STEREO mode In STEREO mode In STEREO mode In STEREO mode

STEREO 9:30AM SAP (STEREO) 9:30AM SAP (MAIN) 9:30AM MAIN 9:30AM

In SAP mode In SAP mode In SAP mode In SAP mode

MONO 9:30AM MONO (SAP) 9:30AM MONO (SAP) 9:30AM MONO 9:30AM

In MONO mode In MONO mode In MONO mode In MONO mode

Additional Picture and Sound Adjustment Options

When stereo sound is difficult to hear, manually switch to MONO for clearer sound. The panel’s sound remains in mono even if the system receives a stereo broadcast. Reselect STEREO to hear broadcasts in stereo where available.

Selecting MTS while the input source is INPUT 1 to INPUT 7 or a PC does not change the type of sound. In this case, the video source determines the sound.

4.7.4 Apply Sound Effect Settings

Your flat panel TV offers four sound effects: SRS FOCUS, SRS, SRS TruBass and SRS Definition.

•SRS FOCUS

•SRS

effortlessly produces a three-dimensional sound field

•SRS TruBass

•SRS Definition

To activate one or more of the sound effects, follow the directions below.

1 ) Access the

moves sound source direction vertically and makes sound and voice clearly audible

produces a clear, rich bass tone

improves midrange quality and clarifies voice and instrument sound

Sound

through the

Setup.

2 ) Select

Sound Effect

from the Sound menu.

3 ) Select a sound effect option.

(SRS FOCUS, SRS, SRS TruBass, SRS Definition)

4 ) Select

Low

(moderate),

Mid

(standard),

High

(enhanced) or

Off

for that option.

5 ) Press HOME MENU to exit the menu.

Note: How a Sound Effect changes the Audio depends on the signal.

(SRS WOW HD

) indicates that SRS FOCUS, SRS, SRS TruBass and SRS Definition are on.

4.7.5 Use Auto Volume Control (AVC)

Auto Volume Control, or AVC, reduces sudden volume change and compensates source sound level.

To select this option, follow the procedure below.

1 ) Access the 2 ) Select 3 ) Select

AVC On

(or

through the

from the Sound menu.

Off

Setup.

Sound

4 ) Press HOME MENU to exit the menu.

Additional Picture and Sound Adjustment Options

4.8 Manage the Power

Your flat panel TV is energy efficient but includes functions to save additional power. In an earlier section entitled “3.6 Smart Starts for New Owners”, you were told how to activate the Energy Save feature. This section provides more advanced functions to save power and to extend the panel life.

AV/PC Source - Picture Off

To save energy and extend the life of your flat panel TV, have the screen turn Off. To deactivate the screen, follow the steps below.

1 ) Press TOOLS on the remote control.

The TOOLS Menu appears on screen.

2 ) Select 3 ) Press ENTER.

Picture Off

from the TOOLS Menu.

The screen display turns Off. To restore the screen display, press any buttons other than

VOL +/–

and

MUTING

Note: The Picture Off setting is not memorized by the system.

AV Source - No Signal

To save energy and extend the life of your flat panel TV, the panel can enter Standby automatically if the AV source signal fails for 15 consecutive minutes. At five minutes before and at every minute after that, a warning message appears on the screen. When the final minute elapses, the panel switches to Standby.

To have the panel switch to Standby when an AV source signal fails, follow the steps below.

1 ) Access the 2 ) Select 3 ) Select 4 ) Press HOME MENU to exit the menu.

Power Control No Signal off Enable

to activate the AV Signal off power function.

through the

from the Power Control menu.

Setup.

Note: The flat panel TV may switch to Standby when there is noise (signal interference) at the end of a broadcast

schedule (channel goes off-air).

AV Source - Non-Operational

To save energy and extend the life of your flat panel TV, the panel can enter Standby automatically if there are no commands from the AV source for three consecutive hours. At five minutes before and at every minute after that, a warning message appears on the screen. When the final minute elapses, the panel switches to Standby.

To have the panel enter Standby automatically when there are no commands from the AV source, follow the steps below.

1 ) Access the

Power Control

through the

Setup.

2 ) Select 3 ) Select 4 ) Press HOME MENU to exit the menu.

No Operation off Enable

from the No Operation off menu.

from the Power Control menu.

Additional Picture and Sound Adjustment Options

PC Source -Power Management

When receiving signals from a PC, the panel can automatically enter Standby if the signal fails. Follow the steps below to activate this function.

1 ) Access the

Power Control

through the

Setup

2 ) Select 3 ) Select an option from the submenu.

Note: Pressing the remote’s

4 ) Press HOME MENU to exit the menu.

These power management options are unavailable when a PC is connected to the panel through the HDMI port/ terminal.

Power Management

Option Description

Off no power management (default) On panel enters Standby when no signal is received

from the Power Control menu.

from the PC for effect on the panel

TV ()

or the panel’s

STANDBY/ON

eight minutes;

reactivates the flat panel TV.

using the PC has no

VOL

123

456

789

ENTER

CH RETURN

EXIT

TOOLS

SAT GUIDE

DVD

TOP MENU

SAT / DVD MENU

HDMI

CTRL

SOURCE

INPUT

RCV VCRSAT

CBL

DVR

DVD

STOP

VOL

SELECT

EDIT/LEARN

REC

HMG

HOME

RETURN

MUTING

INPUT

TV/DTV

DISPLAY

FREEZE

SCREEN SIZE

SELECTION

SPLIT

SWAP

SHIFT

ENTER

RECEIVER

2 cm to 5 cm (0.8 inches to 2.0 inches)

Remote control (Supplied accessory)

Remote control of AV product

1 2 3

456

789

INPUT

RCV VCRSAT

CBL

DVR

DVD

VOL

SELECT

RECEIVER

EDIT/LEARN

Use Other Equipment With Your Flat Panel TV

5 Use Other Equipment With Your Flat Panel

Although earlier sections have mentioned other equipment for playing back video, this section provides control and operation information for specific types of equipment.

5.1 Program the Remote Control to Operate Other Equipment

To operate other equipment or devices through your flat panel TV, program the panel’s remote control with the equipment’s Learning function or manufacturing code. A manufacturing code is a series of numbers that identi fy the type of device and the brand. These codes are available in the section entitled “8.2 Manufacturer Codes to Program into the Remote Control” in Appendix 8.2 of this manual.

5.1.1 Use the Learning Feature

The Learning function allows the panel’s remote control to memorize other remote controls’ codes.

To activate the Learning function follow the directions below.

1 ) Press SELECT to choose the device to learn. 2 ) Press EDIT/LEARN and 2 at the same time.

The selected mode indicator flashes when the remote control is ready to be learned.

3 ) Use the number buttons to learn a manufacturing code.

The mode indicator lights up. The Learn session is canceled in 30 seconds and the indicator restarts blinking again. When the indicator flashes, the selected device’s remote is memorized. To exit the Learn mode before it finishes, press

EDIT/LEARN.

4 ) Press EDIT/LEARN again to exit the Lean mode.–

Note: The Learn session is canceled:

– if no operation is performed for more than one minute after

having pressed

flashing) – if you press – Code transmission finishes in approximately two seconds. Do not interrupt it until the transmission is

complete. Wait until the mode indicator flashes again. When using any of the receiver buttons (

VOL+/–

EDIT/LEARN

SELECT

), the learned manufacturer code remains the same.

and 2 (the mode indicator is

, INPUT

Use Other Equipment With Your Flat Panel TV

1 23

456

789

INPUT

RCV VCRSAT

CBL

DVR

DVD

VOL

SELECT

RECEIVER

EDIT/LEARN

123

FREEZE

SPLIT

SWAP

SHIFT

TOP MENU

SAT / DVD MENU

HDMI

CTRL

SOURCE

INPUT

RCV VCRSAT

CBL

DVR

DVD

STOP

VOL

SELECT

REC

HMG

HOME MENU

RETURN

ENTER

RECEIVER

To delete a learned code, overwrite it with a new code on the same button or follow the directions below.

1 ) Concurrently press EDIT/LEARN and 2.

The selected mode indicator flashes when the remote control is ready to be learned.

2 ) Press and hold TV for more than two seconds.

The remote control starts deleting all learned codes for selected modes. When completed, the mode indicator blinks Off and the remote control returns to normal operation.

5.1.2 Assign a Manufacturing Code to the Remote Control

To assign a preset Manufacturing code to the panel’s remote control, follow the directions below. (For Manufacturing codes, refer to “8.2 Manufacturer Codes to Program into the Remote Control.”)

1 ) Press SELECT to choose the device to program. 2 ) Press EDIT and 1 at the same time.

The selected mode indicator flashes when the remote control is ready to be programmed.

3 ) Use the number buttons to enter a manufacturer code.

When the indicator turns off, the code has been programmed into the remote control.

5.1.3 Issue a Library Search for a Manufacturer Code

If the code for a particular device is unknown, cycle through the available codes for a similar unit then sample some functions for that code.

To find the code that properly operates the unit, follow the steps below using differemt codes to find the best match.

1 ) Press SELECT to choose the device to program. 2 ) Press EDIT and 3 at the same time.

The selected mode indicator flashes when the remote control is ready to search the code library.

3 ) Sample the code using a SOURCE POWER, PLAY, 1 or CH+

command.

4 ) Use the up/down arrow (/) buttons to advance to the next code

if the code fails to control the device.

Another option is to return to the previous code and repeat Step 3.

5 ) Press ENTER to lock in the code that properly operates the device.

All the available buttons for the selected mode are added when the mode indicator flashes on for one second. The remote control then returns to normal operation.

EDIT/LEARN

INPUT

TV/DTV

DISPLAY

SCREEN

SIZE

SELECTION

SAT / DVD MENU

HDMI

CTRL

SOURCE

INPUT

EDIT/LEARN

STOP

VOL

SELECT

REC

HMG

HOME MENU

RETURN

RECEIVER

RCV VCRSAT

CBL

DVR

DVD

HDMI

CTRL

SOURCE

INPUT

RCV VCRSAT

CBL

DVR

DVD

STOP

VOL

SELECT

REC

HMG

RECEIVER

EDIT/LEARN

Use Other Equipment With Your Flat Panel TV

5.1.4 Clear Added Manufacturer Codes from the Remote Control

To return all learned and preset codes to the defaults (PIONEER), follow the steps below.

1 ) Press EDIT and TV  at the same time.

Selection can be in any mode.

2 ) Press the Yellow button.

Confirm that the selected mode indicator flashes. The remote control enters the Manufacturing Reset mode. The

reset is complete when the mode indicator flashes on for one second. The remote control then returns to normal operation.

Note: The panel’s remote control may not control or have complete

control of some equipment listed in the tables.

To exit before the reset is complete, press the EDIT button again. The reset is cancelled if no action is taken within 60 seconds. Also, switching the Mode during this procedure cancels the reset.

5.1.5 Control a Pioneer Receiver

The flat panel TV’s remote control has a bank of buttons specifically for controlling a Pioneer receiver. The active buttons, left to right, are as follows:

• RECEIVER STANDBY/ON (turns the Pioneer Receiver On/Off)

• RECEIVER INPUT (cycles through/selects an input)

• RECEIVER VOL – (adjusts the volume lower)

• RECEIVER VOL + (adjusts the volume higher)

Use Other Equipment With Your Flat Panel TV

5.1.6 Control a Cable (CBL) or Satellite (SAT) System

When Mode is set to CBL/SAT, a cable converter uses the buttons 1, 6, 7, 8, and 9 while satellite tuners use the buttons 1 to 8. However, the panel only recognizes a single system (cable or satellite) at a time.

• Number buttons

(press to enter a channel number)

• SAT GUIDE

(displays the satellite broadcasting guide screen)

• ENTER

(Enter activates the selected function) (arrows to select from SAT GUIDE or MENU screens)

• SAT MENU

(displays the satellite broadcasting menu screen)

• SOURCE

(turns the equipment power on and off)

• CH ENTER*

(enters the selected channel with the direct channel selection buttons)

• CH RETURN*

(press buttons that correspond to a channel)

• CH +/–

(selects a higher or lower channel)

• RETURN

(restores the immediately previous screen)

* Some cable converter manufacturers do not preset

CH ENTER and CH RETURN.

INPUT

DISPLAY

SELECTION

FREEZE

SPLIT

SWAP

123

456

789

CH RETURN

VOL

MUTING

EXIT

SAT GUIDE

DVD

TOP MENU

TV/DTV

SCREEN

SHIFT

ENTER

TOOLS

SIZE

6 7

RECEIVER

INPUT

CBL

RCV VCRSAT

ENTER

STOP

VOL

DVD

DVR

RETURN

REC

HMG

EDIT/LEARN

HOME MENU

SAT / DVD MENU

HDMI

CTRL

SOURCE

SELECT

789

Use Other Equipment With Your Flat Panel TV

5.1.7 Control a Video Cassette Recorder (VCR)

When Mode is set to VCR, verify that the proper Input is selected (INPUT 1 to INPUT 7) then use 1 to 8 to control the device.

• REWind (rewinds the VCR tape and allows searches)

• PAUSE/STILL (pauses playback and displays still images)

• SOURCE (turns the VCR’s power on and off)

• CH +/– (selects a higher or lower channel)

• PLAY (selects playback)

• FF (advances the VCR tape and allows searches)

• STOP

VOL

EXIT

DVD

TOP MENU

HOME MENU

CH RETURN

MUTING

SAT GUIDE

ENTER

TOOLS

RETURN

(halts VCR tape transport)

• RECord (begins recording)

1 2

SAT / DVD MENU

HDMI

CTRL

SOURCE

SELECT

RECEIVER

INPUT

CBL

RCV VCRSAT

STOP

VOL

DVD

DVR

REC

HMG

EDIT/LEARN

5 6

7 8

Use Other Equipment With Your Flat Panel TV

789

5.1.8 Control a DVD Player/DVR Recorder/BD Player

When Mode is set to DVD/DVR, the remote control can operate DVD players, DVD recorders or BD players connected to the flat panel TV. Verify that the proper Input is selected for the device then use 1 to 14 to control it.

Note: Equipment from other manufacturers (DVD players, DVD recorders, BD players, and HD-DVD players) can

also be operated using the remote control if the remote is preset for the device(s).

• DVD TOP MENU

(displays the top menu on the DVD)

• ENTER

(ENTER activates the selected function) (arrows to select from SAT GUIDE or MENU screens)

• DVD MENU

(displays the DVD menu)

• Red/Green/Blue/Yellow (BD only)

(controls a BD-J application)

• REVERSE SCAN/CHAPTER SEARCH

(press once quickly to go to beginning of current chapter; press again to go back to the beginning of the previous chapter; continue pressing to go backward)

• PAUSE/STILL

(pauses playback and displays still image)

• SOURCE

(turns the equipment power on or off)

• CH +/– (DVD Recorder only)

(selects a higher or lower channel)

• TOOLS

(assigns the code for a Pioneer BD player)

• RETURN

(restores the immediately previous screen)

• PLAY

(selects playback)

• FORWARD SCAN/CHAPTER SEARCH

(press once quickly to go to beginning of next chapter; press again to advance to beginning of next chapter; continue pressing for fast forward)

• STOP

(halts DVD playback, some DVD players/recorders open the disc tray if this button is pressed twice)

• RECord (DVD Recorder only)

(begins recording)

STOP

VOL

DVD

DVR

ENTER

TOOLS

RETURN

REC

HMG

EDIT/LEARN

11 12

13 14

CH RETURN

VOL

MUTING

EXIT

SAT GUIDE

DVD

TOP MENU

HOME MENU

SAT / DVD MENU

ENTER

4 5

6 7

HDMI

CTRL

SOURCE

SELECT

RECEIVER

INPUT

CBL

RCV VCRSAT

13 14

& STOP RECord (DVD Recorder only) (press and hold  then press  to stop recording applies to Pioneer DVD recorders only)

Use Other Equipment With Your Flat Panel TV

5.2 Use HDMI Inputs

High Definition Multimedia Interface (HDMI) is a communication method commonly used by digital and/or high definition equipment. Your flat panel TV’s INPUT 4, INPUT 5, INPUT 6, INPUT 7 are HDMI terminals for incoming digital video and audio signals. The flat panel TV supports HDMI Control functions so that when a piece of equipment is connected to the panel, it can control the equipment. To use an HDMI terminal, specify the types of video and audio signals being sent from the connected equipment. For the signal types, see the operating manual(s) that came with the equipment.

One of the benefits of using your flat panel TV to control other equipment is the support of Deep Color. Deep Color is the color depth that describes the number of bits used to represent the color of a single pixel in a bitmapped image. Besides the conventional RGB/YCbCr16bit/20bit/24bit signals, the flat panel TV also supports RGB/YCbCr30bit/36bit signals. This enables finer color reproduction when a device that supports Deep Color signals (HDMI1.3 Deep Color) is connected to the panel. The color depth appears on the InfoBanner if a program supports Deep Color.

The flat panel TV supports the following Video signals:

Supported Video Signals Supported PC Signals

• 1920 x 1080p@60 Hz

• 1920 x 1080p@24 Hz

• 1920 x 1080i@59.94 Hz/60 Hz

• 1280 x 720p@59.94 Hz/60 Hz

• 720 x 480p@59.94 Hz/60 Hz

• 720 (1440) x 480i@59.94 Hz/60 Hz

• 1280 x 1024 (SXGA) 60 Hz

• 1360 x 768 (Wide - XGA) 60 Hz

• 1024 x 768 (XGA) 60 Hz

• 800 x 600 (SVGA) 60 Hz

• 640 x 480 (VGA) 60 Hz

Note: It may take a short period for the image to appear on the other equipment, depending on the type of device.

The flat panel TV supports the following Audio signals:

• Linear PCM (STEREO 2ch)

• Sampling frequency: 32 kHz, 44.1 kHz, 48 kHz

When connecting a PC to one of the panel’s HDMI inputs, use an HDMI-compliant PC or video card. Using DVI output from the PC to the flat panel TV may cause the sound or picture to fail or seem distorted. If a DVI output is your only option then contact the PC manufacturer for assistance.

5.2.1 Specify the HDMI Input Type

To select a signal type, follow the steps below.

1 ) Select the Input for the connected equipment.

Press the

INPUT

button (remote control or panel) until the correct input is showing (INPUT 4, INPUT 5,

INPUT 6, or INPUT 7).

Note: For INPUT 4 and INPUT 5, add Audio cables to support analog signals.

2 ) Access the 3 ) Select 4 ) Select 5 ) Select the appropriate option.

6 ) Press HOME MENU to exit the menu.

Option

through the

HDMI Input Signal Type

Video use except when a PC is connected (default) PC when a PC is connected to HDMI input terminal

from the Option menu.

from the submenu.

Option Description

Setup.

Use Other Equipment With Your Flat Panel TV

Video (over-scan)

PC (under-scan)

In Video mode, the image is over-scanned (enlarged) but the panel automatically switches to PC when receiving computer signals. In PC mode, the image displays in full size for optimum image quality.

5.2.2 Specify a Digital HDMI Signal Type

For the necessary digital video signal type, check the operating manual that came with the other equipment.

To assign the type of digital signal, follow the steps below.

Option

1 ) Access the

through the

Setup.

2 ) Select 3 ) Select 4 ) Select the type of digital video signal recommended for the attached device.

5 ) Press HOME MENU to exit the menu.

If an image fails to appear, specify another digital video signal type. Type parameters other than Auto need to be checked for natural colorings.

HDMI Input Video

Auto automatically identifies input digital signals

Color-1 Digital Component Video signals (4:2:2) locked Color-2 Digital Component Video signals (4:4:4) locked Color-3 Digital RGB signals (16 to 235) locked Color-4 Digital RGB signals (0 to 255) locked

from the Option menu.

from the submenu.

Type Description

(default)

5.2.3 Specify an Audio HDMI Signal Type

For the necessary audio signal type, check the operating manual that came with the other equipment. When using INPUT 4 or INPUT 5 for HDMI, select the terminal for the desired input source.

To specify the audio type, follow the steps below.

Option

1 ) Access the

through the

Setup.

2 ) Select 3 ) Select 4 ) Select the type of audio signal recommended for the attached device.

5 ) Press HOME MENU to exit the menu.

HDMI Input Audio

from the submenu.

Auto Digital accepts digital audio signals Analog accepts analog audio signals

from the Option menu.

Type Description

automatically identifies input audio signals (default)

Use Other Equipment With Your Flat Panel TV

If there is no sound, specify another audio signal type. Depending on the type of equipment, sound output may require analog audio cables in addition to the HDMI connection(s).

Note: When signals come through the HDMI terminals, no signals are output from the DIGITAL OUT terminal if they

are copy guarded.

5.3 Control Equipment with the Panel’s Remote Through HDMI

Your flat panel TV’s remote can control other equipment such as a recorder, player, or AV system through the HDMI Control functions. The HDMI Control functions include playback of content using an on-screen control panel. However, not all device operations may be available through HDMI control. For details, see the charts below.

Control Function

Playback of content

On-screen control Recorder

Display Language Setup

AV system control AV system Receiver/amplifier operation can also

Power ON Recorder

Power OFF Recorder

Controlled

Equipment

Recorder Player

Player

Recorder Player

Player

Player AV system

Function Description

Pressing PLAY on a connected device automatically selects the source and begins playback

Recorder/player operation can be controlled on-screen or with the panel’s remote (play, stop, fast forward/reverse, etc.)

Information on the display menu language transfers to the recorder or player connected to the flat panel TV. For details, see the operation manual that came with the recorder or player.

be controlled with the panel’s remote, (volume, surround mode and input selection of the HDMI terminal)

The flat panel TV can be turned On when a connected recorder(s) or player(s) is turned On and images are input to the flat panel TV

The connected device(s) can be turned Off when the flat panel TV is turned Off

Notes: The KURO LINK function name used on the web and in catalogs is referred to as HDMI Control in the

operating instructions and on the product. Except for Power Off and Display Language Setup functions, only a single HDMI terminal may be active at a time.

The flat panel TV’s remote can control a maximum of two (2) recorders, two (2) playback devices, and one (1) AV system at a time.

To select and use the various HDMI Control functions for a connected Pioneer AV system, recorder, or player, use the panel’s HDMI Control menu.

Use Other Equipment With Your Flat Panel TV

To access the menu, follow the steps below.

1 ) Press HOME MENU.

2 ) Select

HDMI Control

from the main menu.

Use the arrow buttons to highlight an option then press

Disc Navigator CTRL Panel(AV-SYS) Playback CTRL Panel Switch to AV Sound

Note: Pressing

Disc Navigator displays a title list of connected recorder or player CTRL Panel (AV-SYS) displays the control panel for connected AV system Playback CTRL Panel displays the control panel for connected recorder

Switch to AV Sound/ Switch to TV Sound

HDMI CTRL

on the remote also causes the HDMI Control menu to open.

Option Description

or player switches between the flat panel TV screen and the

connected AV system for sound output

ENTER

Use the following buttons to control functions such as the disc navigator on a recorder or player.

• VOL +/– (adjusts the volume for an AV system)

• MUTING (turns off the sound while the video continues to play)

• Arrow buttons (navigates the menu screen)

• Color buttons (Red, Green, Blue, Yellow) (controls a BD player)

• TOOLS (assigns the code for a Pioneer BD player)

• ENTER (activates the selected function)

• RETURN (returns to the previous menu screen)

To connect a device for HDMI Control, follow the steps below.

1 ) Turn on the flat panel TV and all other equipment. 2 ) Confirm that the panel’s Input Setting for HDMI Control Setting options comply with directions in the

operating instructions for the connected device(s).

Use Other Equipment With Your Flat Panel TV

3 ) Confirm that the other equipment is set for HDMI Control. 4 ) Check that the audio and video are playing back properly from the equipment connected to the HDMI

terminal(s). 5 ) Turn Off the flat panel TV. 6 ) Pause for a few seconds before turning the power back on. 7 ) Verify that all equipment is functioning properly.

To select the device to control via HDMI Control, follow the steps below.

1 ) Access the

Option

through the

Setup.

2 ) Select 3 ) Select

HDMI Control Setting Input Setting

from the submenu.

from the Option menu.

Input Setting : INPUT 4 Power Off Control : On Power-On Ready : On Hold Sound Status : Off

Power On Test Power Off Test

4 ) Select the desired Input (INPUT 4, INPUT 5, INPUT 6, or INPUT 7). 5 ) Press HOME MENU to exit the menu.

If operating an HDMI supported device using an HDMI port other than the terminal selected in Input Setting, the system malfunctions. When connecting to an HDMI terminal other than that selected in Input Setting, the equipment settings should block HDMI Control functions. The HDMI Control menu is not selectable when the option Input Setting under the HDMI Control Setting menu is set to Off.

The control menu changes to suit the type of HDMI-compatible equipment. When adding, changing, or removing equipment from HDMI Control, refer to the sections below for installation notes and the supported commands.

5.3.1 Control an AV System

When adding an AV System, connect the unit between the panel and any recorders and/or players. To function properly, an Audio/Video system should support the HDMI Control functions between the panel and any other connected equipment.

If the AV system does not support HDMI Control but the other equipment (player/recorder) accepts this type of control than connect the AV System through the panel’s DIGITAL OUT using an optical digital cable and AUDIO OUT using an AV cable (commercially available). The other equipment connects to the HDMI port using an HDMI compliant cable. Signals input from the HDMI are not output from DIGITAL OUT.

Use Other Equipment With Your Flat Panel TV

During playback, use the remote control’s up/down arrows (/ ) to cycle through the surround sound options. Use the left/right arrows (/ ) to change the input. To resume playback, return to the HDMI Control menu then select the function again.

AV Systems

HDMI Control

1 Cycles the surround mode in sequence 2 Switches the input source in reverse order

3 Switches the surround mode in reverse order 4 Closes the screen to return to HDMI Control

5 Lists the connected equipment

(model number) 6 Switches the input source in sequence 7 Reserved/Void

5.3.2 Control a Recorder

Press ENTER to start playback or press HDMI CONTROL to return to the menu. This process also applies to Players. Refer to the chart below for available commands.

****

SURROUND+

INPUT+INPUT-

SURROUND-

Exit

5 6

Recorders

HDMI Control

1 Skips commercials 2 Fast reverse

3 Stops playback 4 Closes the screen to return to HDMI Control

menu 5 Lists the connected equipment

(model number) 6 Fast forward 7 Starts playback

Note: You can also use  (Play), (Stop),  (Pause), (Fast Forward) and  (Fast Reverse) on the remote

control to conduct the same operations as the control menu buttons.

5.3.3 Control a Player

Press ENTER to start playback or press HDMI CONTROL to return to the menu. This process also applies to Recorders. Refer to the chart below for available commands.

Players

1 Displays the DVD/Blu-ray disc menu on the

player 2 Fast reverse

3 Stops playback 4 Closes the screen to return to HDMI Control

menu 5 Lists the connected equipment

(model number) 6 Fast forward 7 Starts playback

****

Exit

HDMI Control

****

Exit

5 6

Note: You can also use  (Play), (Stop),  (Pause), (Fast Forward) and  (Fast Reverse) on the remote

control to conduct the same operations as the control menu buttons.

T W

Rear view

HDMI compliant cable (HDMI cable having the HDMI mark)

AV cable (commercially available)

Optical digital cable (commercially available)

BD player

AV amp

HDMI compliant cable (HDMI cable having the HDMI mark)

AV cable (commercially available)

Optical digital cable (commercially available)

BD player AV amp

Rear view

HDMI compliant cable (HDMI cable having the HDMI mark)

Rear view

BD player

Use Other Equipment With Your Flat Panel TV

5.3.4 Add an AV Amp or a BD Player

To add an AV amp and/or a BD Player, refer to the appropriate cabling diagram below.

AV Amp & BD Player

T W

BD Player only

T W

Use Other Equipment With Your Flat Panel TV

5.4 Specific HDMI Control Commands

When using HDMI equipment with your flat panel TV, some options include when to power the panel and ways to turn other devices or features On and Off. This section provides steps for commonly desirable setting changes.

5.4.1 Play Source Sound Using an HDMI Command

When sound is coming from a Pioneer AV System through the flat panel TV, placing the panel in Standby causes the sound to stop. To have the sound continue when the flat panel TV turns On, follow the steps below.

Option

1 ) Access the

through the

Setup.

2 ) Select 3 ) Select 4 ) Select 5 ) Press HOME MENU to exit the menu.

HDMI Control Setting Hold Sound Status On

to allow sound from an AV System to play when the panel turns On.

from the Option menu.

from the submenu.

Note: To have the sound continue when the flat panel TV turns On, confirm that the Switch to TV Sound option

appears on the HDMI Control menu before turning the panel Off (see page 87).

5.4.2 Turn OFF the Power With an HDMI Command

The “Power Off Control” function is valid for the devices connected to any of the panel’s HDMI ports. To power off a connected device when the flat panel TV is turned Off, follow the steps below.

Option

1 ) Access the 2 ) Select 3 ) Select 4 ) Select 5 ) Press HOME MENU to exit the menu.

HDMI Control Setting Power Off Control On

to allow the panel to power off the connected equipment.

through the

Setup.

from the Option menu.

from the submenu.

5.4.3 Turn ON the Power With an HDMI Command

The panel ships from the factory with the Power On command activated. If this feature is turned off in error, it can be reactivated. To power on the flat panel TV automatically when a connected Pioneer recorder or player is turned On and images are sent to the panel, follow the steps below.

Option

1 ) Access the

through the

Setup.

2 ) Select 3 ) Select 4 ) Select 5 ) Press HOME MENU to exit the menu.

HDMI Control Setting Power-On Ready On

to have another device power-on the panel.

from the Option menu.

from the submenu.

Use Other Equipment With Your Flat Panel TV

5.4.4 Test the Power Control (On/Off)

Your flat panel TV provides an HDMI control option to test equipment power when it is connected to the panel’s HDMI ports and it has been properly assigned to an Input.

To confirm that the Power On/Off control function is working, follow the steps below.

Option

1 ) Access the

through the

Setup

. 2 ) Select 3 ) Select a test option (

HDMI Control Setting

Power On Test or Power Off Test

from the Option menu.

) from the submenu.

A list containing all HDMI connected equipment appears.

4 ) Select a piece of equipment from the list. 5 ) Repeat this process to test other equipment from the list. 6 ) Press HOME MENU to exit the menu when all testing is complete.

If the Power On/Off Test fails, check the connection points and the settings.

5.5 Connect a Game Console or Camcorder

Your flat panel TV supplies direct connections for a game console, camcorder, or other Audio/Visual (AV) equipment through INPUT 3. To watch an image coming from a game console or camcorder, press INPUT 3 on the remote control or repeatedly press INPUT on the panel to select INPUT 3. For details on game console settings, refer to “2.6.2 Connect Your Other Pioneer Equipment” and “4.1.4 Set the Panel to Recognize a Game Console.”

Use the connection type specified by the equipment. Connect equipment only to terminals that are actually to be used.

5.6 Use the IR REPEATER OUT

Connecting control cables between the flat panel TV and other Pioneer equipment allows to operate the connected equipment by sending commands from its remote control to the remote control sensor on your flat panel TV.

This function is helpful when controlling Pioneer equipment from other Pioneer equipment.

Use Other Equipment With Your Flat Panel TV

5.7 Operate the Home Media Gallery

With Home Media Gallery, you can enjoy digital content such as movies, music, and photo files on your high-end flat panel TV. Play content from files stored on one or more media servers connected by a home or local area network (LAN) or those stored on a USB flash drive. After connecting via a broadband router or an Ethernet hub to a media server with network software, navigate through the digital content visible on the Home Media Gallery. The flat panel TV supports Mass Storage Class and PTP devices through USB interface and DLNA-compatible devices through a network.

DLNA CERTIFIED™ Audio/Video/Image Player

This unit complies with the DLNA Networked Device Interoperability Guidelines - expanded: October 2006 (v1.5). When a PC running DLNA server software or other DLNA-compatible device is connected to this player, some setting changes of software or other devices may be required. Please refer to the operating instructions for the software or device for more information.

PlaysForSure

PlaysForSure is a marketing certification given by Microsoft. The PlaysForSure logo makes it easy to find digital media stores and devices that work together. Digital media purchased from online stores carrying the PlaysForSure logo is available for use on this unit. This unit complies with PlaysForSure Version 2.20 Requirements Specification for Network Devices.

Supported File Formats

The following sections show supported file formats that can be played back or displayed on the flat panel TV. These formats are applicable to network sources. Most are also applicable to USB sources. However, media server content protected by digital rights management such as WMDRM10 (Windows Media Digital Rights Management 10), may not play on the panel.

Supported Video Formats

• Windows Media Video 9 (WMV9): MP@ML

• Windows Media Video 9 (WMV9) Advanced Profile (VC-1): AP@L1, MP@ML

• MPEG-2 PS: MP@ML

• MPEG-2 TS: MP@ML

• MPEG-1

• MPEG-4 Part2 (SP/ASP): SP@L3, ASP@L5

• MPEG-4 Part10 (H.264/AVC): Main Profile 3.0

Supported Audio Formats

• Windows Media Audio 9 (WMA9): Sampling rates; 44.1 kHz or 48 kHz

• MPEG-1 Audio Layer 3 (MP3): Sampling rates; 32 kHz, 44.1 kHz or 48 kHz

• Linear PCM (WAV): Sampling rates; 44.1 kHz or 48 kHz

• MPEG-4 AAC: Sampling rates; 16 kHz, 32 kHz, 44.1 kHz or 48 kHz

• HE-AAC: Sampling rates; 16 kHz, 32 kHz, 44.1 kHz or 48 kHz

Supported Image Formats

• JPEG: Resolution; up to 3680 x 2760 pixels

• PNG: Resolution; up to 3680 x 2760 pixels

• GIF: Resolution; up to 3680 x 2760 pixels

• TIFF: Resolution; up to 1600 x 1200 pixels

• BMP: Resolution; up to 3072 x 2304 pixels

Supported File Extensions

This product supports the playback of files with the following extensions.

• Video: .wmv, .asf, .mpg, .mpeg, .mpe, .m2p, .m4v, .mp4v, .mp4, .mov

• Audio: .wma, .mp3, .wav, .m4a, .aac

• Image: .jpg, .jpeg, .png, .gif, .bmp, .tif, .tiff

Note: Even the supported format files that are listed above may or may not play properly or completely, depending

on the media server, USB device, bit rate stream and other content characteristics, as well as other factors.

Use Other Equipment With Your Flat Panel TV

Even when files have a supported file extension, some files may not play or display properly, depending on the content or media server type.

Some formats may not be supported nor displayed on Home Media Gallery as formats that individual media servers support vary. Refer to the media server manufacturer’s or other relevant websites for supported formats.

Although a particular format is supported, not all content functions may operate properly. If the content fails to appear properly, contact the content producer for assistance. In addition, some supported file formats may fail to play properly when imported from an unknown USB device.

Note: You cannot use the Home Media Gallery until dimmed elements on the menu screen turn white.

Some Home Media Gallery functions, such as trick play during Fast Forward and Rewind, Time Search and Search, may not work depending on the media server’s capability and functionality.

Home Media Gallery complies with the DLNA Networked Device Interoperability Guidelines - expanded: October 2006 (v1.5) and PlaysForSure Version 2.20 Requirements Specification for Network Devices. If your media server supports different DLNA and/or PlaysForSure version(s), some Home Media Gallery function(s) and content format(s) may not be supported.

Pioneer is not responsible for any malfunction of the Home Media Gallery features due to communication error/malfunctions associated with your network connection and/or your PC, or other connected equipment. Contact your PC manufacturer or Internet service provider.

Content may not play or display properly, depending on the conditions of use or media server in use. The Home Media Gallery functions as a WMDRM10-ND (Microsoft Windows Media DRM for networked devices). Content can only be navigated from the media servers that support WMDRM10-ND. Content may not play, depending on the DRM protection level. This system may not display content from incompatible memory cards.

5.7.1 Network Connections

To connect to a network, set up the Home Media Gallery through the Home Media Gallery menu. Press the HMG button on the remote control to cause the menu to appear. To use the Home Media Gallery, connect to a home network (LAN) via an Ethernet hub or cable directly to a media server.

Usable Media Servers

A media server contains digital content such as movies, music, and photo files. PCs that have pre-installed media server software and recorders with a media server function are considered the media server. There are some media servers that you can choose from; for example, Windows Media Connect, Windows Media Player that has a media sharing function, and DLNA compliant servers.

• Windows Media Connect 2.0 Windows Media Connect runs on a 32-bit PC with Windows XP Service Pack 2 (SP2) installed. When it is already installed, you can enjoy Home Media Gallery using your PC.

• Windows Media Player 11 for Windows XP Windows Media Player 11 features Media Sharing that runs on a 32-bit PC with Windows XP Service Pack 2 (SP2) installed. If Windows Media Connect 2.0 is not installed in your PC, you can download Windows Media Player 11 from Microsoft’s website.

• Windows Media Player 11 for Windows Vista Windows Media Player 11 is featured in 32-bit Windows Vista PCs.

When selecting the most suitable media server, please visit Microsoft’s website for system requirements, known issues, installation procedures, and other updated information.

• DLNA CERTIFIED The server is a DLNA-certified digital media server such as PC software, PCs and other devices installed with DLNA-certified software. When a PC running DLNA server software or other DLNA-compatible device is connected to this player, some setting changes of the software or device may be required. Refer to the device(s) operating instructions for more information.

digital media servers

Use Other Equipment With Your Flat Panel TV

Media server 2

Media server 1

Ethernet hub (Router with hub function)

Straight-through cable

Rear view

Media server 1

Rear view

Cross-over cable

Connect via an Ethernet Hub

If already operating one or more media servers on a home or local area network (LAN), connect the flat panel TV to the Ethernet (LAN) hub using a standard (“straight-through”) Ethernet (LAN) cable. See the diagram below.

Note: Although the Home Media Gallery supports 10BASE-T, it is better to use 100BASE-TX for improved display

quality and speed.

T W

Connect directly to a Media Server

To run a PC as a media server, connect the flat panel TV directly to the PC using a twisted (“cross-over”) Ethernet (LAN) cable. See the diagram below.

T W

Use Other Equipment With Your Flat Panel TV

Confirm the IP Address

After making the network connection, follow the instructions below to confirm the IP Address before accessing the network. (The setup is effective for Auto only. To perform the procedure, DHCP on your server or router must be valid. See “5.10 HMG Setup”)

1 ) Press HMG on the remote control.

The Home Media Gallery menu appears on screen.

2 ) Select

HMG Setup

Use the arrow buttons to highlight an option.

3 ) Press ENTER. 4 ) Select 5 ) Select

Network Setup Auto DHCP

The screen turns from “Select” mode to “Input” mode.

6 ) Select 7 ) Press RETURN.

Yes

The HMG Setup screen returns. The IP Address is assigned.

The Home Media Gallery supports Auto IP and DHCP (Dynamic Host Configuration Protocol). If the system failed to assign the IP Address or if you want to obtain different addresses, select No then enter IP Address and Subnet mask. See Network Setup or HMG Setup to enter an address manually.

For information on DHCP, refer to network device’s operating instructions. You may need to contact your service provider or network administrator when manually entering an IP Address. Some media servers block or are programmed to block access to client servers. When connecting the flat panel

TV, check the media server for client server access rights.

5.7.2 Connect a USB Device

You can also enjoy content stored on memory cards by connecting a USB device to the flat panel TV. The root directory or Device List screen appears as soon as a USB flash drive or a multi-card reader is connected to the USB port. Another option is to connect your digital camera directly to the flat panel TV using a commercially available USB connector cable.

If for any reason, the Folder/Content List or Device List fails to appear, follow the steps below.

1 ) Press HMG.

The Home Media Gallery menu appears on screen.

2 ) Select

USB

Use the arrow buttons to highlight an option.

3 ) Press ENTER to confirm the selection. 4 ) Select the desired device.

The USB Device screen must be displayed.

5 ) Press ENTER to navigate to a folder or play a file/content.

To return to the previous screen, press

6 ) Press EXIT or HMG to exit Home Media Gallery.

RETURN

Note: The flat panel TV displays the USB Device screen or root directory immediately after inserting a USB device.

In this case, start from Step 5. When a multi-card reader is inserted, the USB Device screen is displayed. In this case, start from Step 4.

Use Other Equipment With Your Flat Panel TV

Flat Panel TV

USB flash drive

Digital Camera with USB Mass Storage Class (PTP also supported)

Flash media via USB adapter (Multi-card Reader)

Note: Do not use any USB devices other than those specified. Using other devices can cause a malfunction.

Readable Data Format

This system reads FAT16, FAT32 or NTFS.

Readable Data Files

Movie, music, and photo files play with the exception of Digital Rights Management (WMDRM10) protected files.

Your flat panel TV supports a single USB device at a time. Also, the panel does not support USB hubs. This system may not be able to display modified or edited content from a PC or other equipment. Your flat panel TV supports the USB Mass Storage Class and PTP devices. Some digital cameras may require a setup procedure for Mass Storage Class data transfer. The setup is done on

the camera. See the operating instructions supplied with the digital camera. Depending on the type of your memory card or camera, some images may fail to display.

Remove a USB Device

To remove a USB device, exit the Home Media Gallery first then disconnect the device. Be sure to exit the Home Media Gallery screen before removing the USB device. If you remove the USB device

while the Home Media Gallery screen is displayed, data inside the memory may be damaged. Do not insert or remove the USB device immediately after the system is switched On or Off. This action may cause

data inside the memory to be damaged. Pioneer is not liable for any loss or damage to the data inside the USB flash drive.

(Sample screen)

Use Other Equipment With Your Flat Panel TV

5.8 Run the Home Media Gallery

1 ) Press HMG.

The Home Media Gallery menu appears on screen.

2 ) Select

Media Navigator, USB, HMG Playlist

HMG Setup

Use the arrow buttons to highlight an option then press To return to the previous screen, press

RETURN

ENTER

3 ) Press EXIT or HMG to exit Home Media Gallery.

Media Navigator USB HMG Playlist HMG Setup

Use the Media Navigator

By selecting Media Navigator, the previously selected server menu automatically appears on the screen. When only one server is found, the system automatically connects the server. You can also use the TOOLS Menu to switch to another server or manually select a server from the Server List. The screen automatically changes to the Server List if there are no previous servers.

1 ) Press HMG.

The Home Media Gallery menu appears on screen.

2 ) Select

Media Navigator

Use the arrow buttons to highlight an option then press

ENTER

A server menu appears. The file/folder configuration may vary depending on the server selected.

3 ) Select a desired server from the Server List. 4 ) Select the desired folder to navigate or file/content to play.

Movi Musi Phot

ser File

5 ) Press ENTER.

The appropriate Player launches and begins playing the selected file. To return to the previous screen, press

RETURN

6 ) Press EXIT or HMG to exit Home Media Gallery.

Note: The Media Navigator launch depends on the option selected in

Auto Connection under

Select a server from the Server list to open Media Navigator.

“5.10 HMG Setup.”

Use Other Equipment With Your Flat Panel TV

(Sample screen)

Navigate through a USB Device’s Files and Folders

Like navigating through media servers, select the specific file from a device on the USB Device screen to start an appropriate player. For details, follow the steps below.

1 ) Press HMG.

The Home Media Gallery menu appears on screen.

2 ) Select

USB

Use the arrow buttons to highlight an option then press

ENTER

. The USB Device screen appears. Select the device. When using a single directory device (USB flash drive), the USB Device screen does not appear.

USB A USB B USB C

USB D USB E USB F USB G

3 ) Select the desired folder to navigate or file/content to play. 4 ) Press ENTER.

The appropriate Player launches and begins playing the selected file. To return to the previous screen, press

RETURN

5 ) Press EXIT or HMG to exit Home Media Gallery.

Note: The USB Device screen appears when using a multi-card reader or multiple flash drive devices. In this case,

select the device containing the desired content.

Thumbnail screen

Thumbnail List screen

List screen

(Sample screens)

Use Other Equipment With Your Flat Panel TV

Screen Components

Screen display options are:

•List

• Thumbnail

• Thumbnail List

Press TOOLS then select Change View from the TOOLS Menu to choose from the screen display options. The options are available for Movie, Music and Photo menus.

lder lder

older

ontent

ontent ontent

1. Item being selected

2. Number of total items

3. Scroll bar (displayed when one or more pages follow)

Folder

ontent

Content 2Folder

Content 3

312

100

4. Icon or thumbnail of the selected item (if obtained)

Pioneer PRO-111FD, PRO-151FD Operating Instruction

Specifications and Main Features

Frequently Asked Questions

User Manual