PIONEER PD 10 User Manual

Инструкции по эксплуатации

Thank you for buying this Pioneer product.

Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference..

IMPORTANT

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

D3-4-2-1-1_A1_En

WARNING

This equipment is not waterproof. To prevent a fire or shock hazard, do not place any container filled with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain or moisture.

D3-4-2-1-3_A1_En

WARNING

Before plugging in for the first time, read the following section carefully.

The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit will be used meets the required voltage (e.g., 230 V or 120 V) written on the rear panel.

D3-4-2-1-4*_A1_En

European model only

Information for users on collection and disposal of old equipment and used batteries

Symbol for

equipment

Symbol examples

for batteries

These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points in accordance with your national legislation.

By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items.

These symbols are only valid in the European Union.

For countries outside the European Union:

If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.

K058a_A1_En

WARNING

To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the equipment.

D3-4-2-1-7a_A1_En

VENTILATION CAUTION

When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 10 cm at top, 10 cm at rear, and 10 cm at each side).

WARNING

Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the equipment on thick carpet or a bed.

D3-4-2-1-7b*_A1_En

Operating Environment

Operating environment temperature and humidity: +5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH (cooling vents not blocked) Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light)

If the AC plug of this unit does not match the AC outlet you want to use, the plug must be removed and appropriate one fitted. Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. If connected to an AC outlet, the cut-off plug can cause severe electrical shock. Make sure it is properly disposed of after removal. The equipment should be disconnected by removing the mains plug from the wall socket when left unused for a long period of time (for example, when on vacation).

CAUTION

The /I STANDBY/ON switch on this unit will not completely shut off all power from the AC outlet. Since the power cord serves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power. Therefore, make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation).

D3-4-2-1-7c*_A1_En

D3-4-2-2-1a_A1_En

D3-4-2-2-2a*_A1_En

This product is for general household purposes. Any failure due to use for other than household purposes (such as long-term use for business purposes in a restaurant or use in a car or ship) and which requires repair will be charged for even during the warranty period.

K041_A1_En

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause a fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest PIONEER authorized service center or your dealer for a replacement.

S002*_A1_En

CAUTION

This product is a class 1 laser product classified under the Safety of laser products, IEC 60825-1:2007.

CLASS 1 LASER PRODUCT

D58-5-2-2a_A1_En

Contents

01 Before you start

Disc/content format playback compatibility. . . . . .4

What’s in the box. . . . . . . . . . . . . . . . . . . . . . . . . . 4

Loading the batteries in the remote control . . . . . .4

Using the remote control. . . . . . . . . . . . . . . . . . . . . 4

02 Connecting up

Analog audio output connections . . . . . . . . . . . . . 5

Digital audio output connections. . . . . . . . . . . . . . 5

Using centralized control with other Pioneer

components (PD-30 only) . . . . . . . . . . . . . . . . . . . 5

Plugging in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

03 Controls and displays

Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Front panel display . . . . . . . . . . . . . . . . . . . . . . . . 7

04 Playback

Playing discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Set the power to Standby. . . . . . . . . . . . . . . . . . . . . 8

Fast forward/Fast reverse . . . . . . . . . . . . . . . . . . . .8

Skip function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Direct search

(designate a specific track for playback). . . . . . . . . 8

Repeat playback . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Random playback . . . . . . . . . . . . . . . . . . . . . . . . . .8

Programmed playback (Play tracks in a

predetermined order) . . . . . . . . . . . . . . . . . . . . . . .8

View disc data . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

iPod/iPhone/iPad playback

(PD-30 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Confirm what iPod/iPhone/iPad models are

supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Playing your iPod/iPhone/iPad . . . . . . . . . . . . . . . .9

Playing files stored on USB storage devices . . . . 10

05 Using advanced functions

Playing with high-fidelity sound . . . . . . . . . . . . . . 11

Sound Retriever. . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Pure Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Changing the playback area (layer)

of an SACD/CD . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Adjusting overall display illumination . . . . . . . . . 11

Auto power down (automatically sets power to

standby). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Playback functions . . . . . . . . . . . . . . . . . . . . . . . 11

06 Additional information

Playable disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Playable file formats . . . . . . . . . . . . . . . . . . . . . . 12

Cautions on use. . . . . . . . . . . . . . . . . . . . . . . . . . 13

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . 14

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Before you start01

PD-30

PD-10

7 m

30 °

Chapter 1:

Before you start

Disc/content format playback compatibility

Discs playable on this player are as shown below.

• SACD (Super Audio CD)* (2-channel area only)

•CD

•DSD disc

* “Super Audio CD” is a registered trademark.

Note

• This unit does not permit playback of the multichannel areas of SACD discs.

• This unit’s DIGITAL OUT terminals do not output sound from SACD and DSD discs, nor from iPod/ iPhone/iPad devices.

• When a disc is loaded, turning on the power will not cause playback to automatically start. As a result, timed playback is not possible even if the unit is connected to a timer.

About DualDisc playback

A DualDisc is a new two-sided disc, one side of which contains DVD content video, audio, etc. while the other side contains non-DVD content such as digital audio material. The non-DVD, audio side of the disc is not compliant with the CD Audio specification and therefore may not play. For more detailed information on the DualDisc specification, please refer to the disc manufacturer or disc retailer.

Discs that cannot be played

•DVD-Video

• DVD-Audio

•CD-G

•Video CD

• DTS CD

It is possible that some discs other than the ones listed above may not be playable either.

What’s in the box

Please confirm that the following accessories are in the box when you open it.

• Remote control x1

• AAA/IEC R03 dry cell batteries x2

• RCA audio cable (red/white plugs) x1

•Power cord

•Warranty card

• Operating instructions (This document)

Note

• Illustrations featured in the Operating Instructions may have been modified or simplified for ease of explanation, and may therefore differ from the actual product appearance.

• The illustrations used here are mainly of the PD-30.

Loading the batteries in the remote control

1 Open the rear lid.

PD-30

PD-10

2 Insert the new batteries, matching the polarities as indicated inside the case.

3 Close the rear lid.

PD-30

The batteries included with the unit have been provided to allow you check product operation and may not last long. We recommend using alkaline batteries that have a longer life.

WARNING

• Do not use or store batteries in direct sunlight or other excessively hot place, such as inside a car or near a heater. This can cause batteries to leak, overheat, explode or catch fire. It can also reduce the life or performance of batteries.

Caution

Incorrect use of batteries may result in such hazards as leakage and bursting. Observe the following precautions:

• When inserting the batteries, make sure not to damage the springs on the battery’s  terminals.

• Do not use any batteries other than the ones specified. Also, do not use a new battery together with an old one.

• When loading the batteries into the remote control, set them in the proper direction, as indicated by the polarity marks ( and ).

PD-10

• Do not heat batteries, disassemble them, or throw them into flames or water.

• Batteries may have different voltages, even if they are the same size and shape. Do not use different types of batteries together.

• To prevent leakage of battery fluid, remove the batteries if you do not plan to use the remote control for a long period of time (1 month or more). If the fluid should leak, wipe it carefully off the inside of the case, then insert new batteries. If a battery should leak and the fluid should get on your skin, flush it off with large quantities of water.

• When disposing of used batteries, please comply with governmental regulations or environmental public institution’s rules that apply in your country/ area.

Using the remote control

The remote has a range of about 7 m at an angle of about 30º from the remote sensor.

Keep in mind the following when using the remote control:

• Make sure that there are no obstacles between the remote and the remote sensor on the unit.

• Remote operation may become unreliable if strong sunlight or fluorescent light is shining on the unit’s remote sensor.

• Remote controllers for different devices can interfere with each other. Avoid using remotes for other equipment located close to this unit.

• Replace the batteries when you notice a fall off in the operating range of the remote.

Connecting up 02

Amplifier

Audio cable (included)

PD-30’s rear panel

DIGITAL IN

OPTICAL

DIGITAL IN

COAXIAL

AV amplifier or digital recording device

Optical fiber cable (commercially available)

Coaxial digital audio cable (commercially available)

PD-30’s rear panel

AV amplifier or digital recording device

To other Pioneer component equipped with CONTROL IN jack

Remote control for AV amplifier, etc.

Point the remote control toward the signal receiver on the AV amplifier, etc.

Other Pioneer component equipped with CONTROL IN/OUT jacks

PD-30

To AC outlet

Power cord

PD-30’s rear panel

Chapter 2:

Connecting up

Caution

• Before making or changing the connections, switch off the power and disconnect the power cord from the AC outlet.

• Connect the power cord after all the connections between devices have been completed.

Analog audio output connections

By connecting this unit’s analog audio output to the analog audio input of an amplifier, you can use the amplifier to enjoy analog audio produced from this unit.

Using centralized control with other Pioneer components (PD-30 only)

This unit and other Pioneer components equipped with CONTROL IN/OUT jacks can be controlled with a single remote control by aiming the remote toward the signal receptor on the AV amplifier or other component. This also allows remote control of components not equipped with a remote sensor, or installed in places where the component’s remote sensor cannot be accessed.

Plugging in

Important

• If it is necessary to detach the power cord, first be

sure to press the  front panel of the unit so the PD-30 is turned OFF or the PD-10 is in standby mode before detaching the cord.

• Confirm that the [-OFF-] indicator is not lighted in the main unit’s front panel display before disconnecting the power cord. If the power cord is disconnected while the [-OFF-] indicator is still lighted, the unit’s settings may revert to factory defaults.

• When going on a trip or otherwise not using the unit for an extended period, always disconnect the power cord from its outlet.

STANDBY/ON button on the

English

DeutschFrançais

Digital audio output connections

If desired, the digital audio output from this unit can be connected to an AV amplifier or digital recording device (CD recorder, MD, etc.).

• This unit’s DIGITAL OUT terminals do not output

sound from SACD and DSD discs, nor from iPod/ iPhone/iPad devices.

ANALOG

AUDIO INPUT

Important

Care in the handling of optical fiber cables

• Do not allow optical fiber cables to be bent at sharp angles. When storing optical fiber cables, roll in coils of at least 15 cm diameter.

• When connecting optical fiber cables, align the connectors correctly and insert fully. If the orientation of the cable connector is incorrect and excessive force is applied in the attempt to fasten the connector, the connector may be deformed, preventing the shutter from closing when the cable is removed.

Note

• For digital audio output, CDs played on this unit

must produce linear PCM signals with a sampling rate up to 44.1 kHz and quantitative bits up to 16 bits (some discs may not be playable depending on the connected component and environment). For information about other files, see page 12.

Note

• For connections use a commercially available monaural miniplug cord (without resistor).

• When connecting the CONTROL IN/OUT jacks, commercially available audio cords must also be used to make analog connections. Merely connecting the CONTROL IN/OUT jacks alone will not allow proper system control.

• When a control cord is connected to the PD-30’s CONTROL IN jack, the unit cannot be controlled by pointing the remote control at the PD-30 (the remote sensor is automatically disabled).

Caution

• Do not use any power cord other than the one supplied with this unit.

• Do not use the supplied power cord for any purpose other than that described below.

After you’ve finished making all connections, plug the unit into an AC outlet.

1 Plug the supplied power cord into the AC IN

socket on the rear of the unit.

2 Plug the other end into AC outlet.

Italiano Español Русский

Nederlands

+ 11 hidden pages