Page 1
SGY-CH500B
Speed & Cadence Sensor
SGY-CS500
User’s Manual
Manuel de l'utilisateur
ENEN
FR
Page 2
Table of Contents
Features ................................................................................................................... 2
EN
Important Safety Information ................................................................................... 3
Before Use (Important) ............................................................................................ 9
Product Conguration .............................................................................................12
Part Names and Functions .....................................................................................13
Installation on Your Bike .........................................................................................14
Installing the Cadence Magnet .............................................................................................14
Installing the Speed & Cadence Sensor ..............................................................................15
Installing the Speed Magnet .................................................................................................16
Fixing the Sensor ..................................................................................................................18
Installing and Removing the Batter y ......................................................................19
Troubleshooting ......................................................................................................21
Specications ........................................................................................................ 22
Features
Trip Data Acquisition
This device acquires trip data like speed and cadence, and those data are
displayed on the cyclocomputer.
This product is ANT+™ certied.
Visit http://www.thisisant.com/directory/ for a list of compatible
products and apps.
2
Page 3
Important Safety Information
Pioneer Speed & Cadence Sensor is not a medical device.
Important Information About This Device
This device helps provide feedback about cycling. It is intended solely for
recreational purposes. THE LIMITED WARRANTY PROVIDED WITH THIS
DEVICE CONSTITUTES THE EXCLUSIVE WARR ANTIES FOR THE PRODUCT
AND THE USER’S EXCLUSIVE REMEDIES. TO THE MAXIMUM EXTENT
ALLOWED BY APPLICABLE LAW, ALL OTHER WARR ANTIES, WHETHER
EXPRESS, IMPLIED, OR STATUTORY, INCLUDING WITHOUT LIMITATION ANY
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, ARE HEREBY DISCLAIMED. IN NO EVENT WILL PIONEER,
ITS AFFILIATES, OR THEIR RESPECTIVE EMPLOYEES, DIRECTORS, OR
OFFICERS, BE LIABLE FOR ANY INDIRECT, INCIDENTAL, CONSEQUENTIAL,
SPECIAL, PUNITIVE OR EXEMPLARY DAMAGES IN CONNECTION WITH
THIS DEVICE, REGARDLESS OF THE THEORY OF LIABILITY AND EVEN
IF SUCH DAMAGES ARE FORESEEABLE. BECAUSE SOME STATES OR
JURISDICTIONS MAY NOT ALLOW LIMITATIONS ON THE DUR ATION
OF IMPLIED WARRANTIES, OR LIMITATIONS ON OR EXCLUSIONS OF
CONSEQUENTIAL OR INCIDENTAL DAMAGES, SOME OF THE ABOVE
LIMITATIONS MAY NOT APPLY TO A USER DEPENDING ON HER, HIS, OR ITS
STATE OF RESIDENCE.
EN
3
Page 4
Impor tant Safety Infor mation
EN
WARNING
BEFORE BEGINNING OR •
MODIFYING ANY EXERCISE
ACTIVITY, ALWAYS CONSULT
YOUR PHYSICIAN FIRST. IF YOU
ARE USING A PACEMAKER OR
ANY OTHER IMPLANTED DEVICE,
CONSULT YOUR PHYSICIAN
BEFORE USING A HEART RATE
SENSOR.
THIS PRODUCT IS NOT A •
MEDICAL DEVICE, AND COULD
EXPERIENCE INTERFERENCE
FROM EXTERNAL ELECTRICAL
SOURCES.
WARNING
Follow these guidelines as well to
ensure safe Cycling:
Always use your best judgement, •
and ride in a safe manner. Do not
become distracted by this device
while riding, and always be fully
aware of your surroundings.
Secure your bicycle in a safe place •
before replacing batteries as the
bicycle could fall causing injur y.
Upon replacing the battery, install •
the the battery cover securely to
ensure water resistance and prevent
potential injury if the cover falls off.
Do not leave small parts such as •
screws or the battery in an area that
infants and small children can reach
to prevent accidental swallowing. If
you think this may have happened,
call 911 for a medical emergency.
Before riding, check that the Speed •
& Cadence sensor does not contact
with a crank or spoke.
4
Page 5
Impor tant Safety Infor mation
Before riding, check that the sensor •
and magnets are installed securely.
Also check that the speed detector
arm’s screw is not loose, there
are no cracks in the band, and the
band’s xing tape is not coming off.
Do not leave this device in places •
that are exposed to direct sunlight,
high temperature, high humidity,
or a lot of dust as it may cause the
device to malfunction.
Never dismantle, refurbish, or repair •
this device or any attached parts as
it could cause electrical shock or the
device to malfunction.
Do not use this device if any unusual •
conditions exist such as penetration
by a foreign object, water
submersion, smoke is detected, or
an unusual odor is detected.
Stop using this device immediately
and have it repaired.
Do not subject this device to •
extreme shock by riding on rough
roads. Doing so could damage this
device or cause it to malfunction.
This device communicates using ANT+ •
radio communication. Do not use in
areas that forbid the use of electronic
devices such as hospitals or airplanes
as unintended interference from this
device could cause serious accidents.
CAUTION
Do not wipe this device with •
detergents, chemical duster, or
volatile compounds such as benzine
or thinner as they may cause the
device to malfunction.
Thoroughly remove any excess •
bicycle lubricants or cleaners
from this device as it could cause
damage.
Avoid overly violent impacts on •
this device as it may cause it to
malfunction.
Do not wash this device with a high •
pressure water sprayer as water may
penetrate into this device causing it
to malfunction.
Do not touch or deform the battery •
contacts. This could cause a faulty
connection or short circuit.
EN
5
Page 6
Impor tant Safety Infor mation
EN
WARNING
Batteries (batteries installed) must not
be exposed to excessive heat such as
sunshine, re or the like.
“Perchlorate Material - special handling
may apply.
See
www.dtsc.ca.gov/hazardouswaste/
perchlorate.
(Applicable to California, U.S. A.)”
WARNING
STORE SMALL PARTS OUT OF
REACH OF CHILDREN AND INFANTS.
IF ACCIDENTALLY SWALLOWED,
CONTACT A DOCTOR IMMEDIATELY.
Radio wave caution
This unit uses a 2.4 GHz radio wave •
frequency, which is a band used by
other wireless systems (microwave
ovens and cordless phones, etc.).
In the event noise appears on
your television image, there is
the possibility this unit (including
products supported by this unit)
are causing signal interference
with the antenna input connector
of your television, video, satellite
tuner, etc. In this event, increase the
distance between the antenna input
connector and this unit (including
products supported by this unit).
6
Page 7
Impor tant Safety Infor mation
[For American Users]
IMPORTANT NOTICE
KEEP WARR ANT Y CARD IN A SAFE PLACE FOR FUTURE REFERENCE.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
The grantee is not responsible for any changes or modifications not expressly
approved by the party responsible for compliance. Such modifications could void
the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
WARNING: This product contains chemicals known to the State of California and
other governmental entities to cause cancer and birth defects or other reproductive
harm.
Wash hands after handling.
may cause harmful
EN
7
Page 8
Impor tant Safety Infor mation
[For Canadian Users]
EN
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause inter ference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accep ter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement.
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment and meets RSS-102 of the IC radio frequency (RF)
Exposure rules. This equipment has very low levels of RF energy that are deemed
to comply without testing of specic absorption ratio (SAR).
Cet équipement est conforme aux limites d’exposition aux rayonnements
énoncées pour un environnement non contrôlé et respecte les règles d’exposition
aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet
une énergie RF très faible qui est considérée conforme sans évaluation du débit
d’absorption spécique (DAS).
The ANT+ antenna cannot be removed (or replaced) by user.
L'antenne ANT+ ne peut pas être supprimé (ou remplacé) par l'utilisateur.
Operating Environment
Operating environment temperature and humidity:
-10 °C to +60 °C (+14 °F to +140 °F); less than 85 %RH
Do not install this unit in a poorly ventilated area, or in locations exposed to high
humidity or direct sunlight (or strong articial light)
8
Page 9
Before Use (Important)
Safety Precautions
DANGER
About this Device
Do not throw this device, strike it •
with a hammer or other object, or
pierce this device in any way.
Do not use or leave this device in •
places where it will be exposed to
extremely high temperatures, such
as near a stove or re.
Always keep this device out of the •
reach of infants and small children.
WARNING
About this Device
Do not use this device if it emits an •
unusual odor, heats up, changes
color or shape, or if any other
abnormalities occur during use.
Do not place this device in a •
microwave oven or expose it to high
pressure, since the device may
overheat, rupture, or ignite.
Keep the lithium batter y out of the •
reach of children. Should the battery
be swallowed, immediately consult a
do cto r.
EN
9
Page 10
Before Use (Impor tant)
EN
CAUTION
Do not recharge, disassemble, heat •
or dispose of the batter y in re.
Use a CR2032 (3 V) lithium battery •
only. Never use other types of
batteries with this unit.
Do not handle the batter y with •
metalic tools.
Do not store the batter y with metallic •
materials.
When disposing of used batteries, •
please comply with governmental
regulations or environmental public
institutions rules that apply in your
country or area.
Always check carefully that you are •
loading battery with its (+) and (-)
poles facing in the proper directions.
CAUTION
About Water-resistance
Obser ve the following precautions
in regard to this device’s waterresistant.
Do not place the unit in water.•
Do not expose the unit to a large •
amount of water.
Do not expose to rain for long •
periods of time.
Do not pour or place in warm •
water or water containing soap or
detergent.
Do not use at or near the beach.•
This could cause rust. If exposed
to seawater, thoroughly wipe off
the moisture immediately with a dry
cloth.
If the rubber packing becomes •
soiled, wipe it clean with a dry, clean
cloth.
Do not open the batter y cover •
in humid environments in which
this device could get exposed to
wate r.
10
Page 11
Before Use (Impor tant)
If this device is exposed to a large •
amount of water or moisture,
immediately wipe it down with a
dry cloth.
Only open or close the battery cover
after having completely wiped of f
any moisture. Be sure your hands
are completely dry and you are in an
environment where the unit will not
get exposed to moisture again.
Over exposure or submersion in •
water may require servicing.
This device is water resistant to 6 m.
Malfunctions due to water damage
caused by improper use are not
covered by the product warranty, even
if they occur within the warranty period.
Depending on conditions of use, •
the water-resistant features are
not necessarily guaranteed even
during the warranty period.
EN
11
Page 12
Product Conguration
This product contains the following
EN
parts.
Speed & Cadence sensor •
(main unit, mounting holder)
Cadence magnet •
Speed magnet •
(magnet, holder, sheet)
Sensor mounting band•
Fixing tape for the sensor •
mounting band
User’s Manual (this manual)•
Warranty Card•
12
Page 13
Part Names and Functions
Front View
Cadence sensor
Detects the cadence magnet installed on
the crank.
LED for cadence magn et detection
Blinks green when it detects the magnet
just after the sensor is activated.
LED for speed magnet detection
Blinks red when it detects the magnet just
after the sensor is activated.
Speed detector arm
Adjust the angle by turning the hex screw
(2 mm) (
).
Back View
Speed sensor
Detects the speed magnet installed on
the spoke.
Hex screw for adjusting the angle of
the arm
Battery cover
Mounting holder
EN
13
Page 14
Installation on Your Bike
Mount the Speed & Cadence sensor, cadence magnet, and speed magnet on
EN
your bike.
Pairing with the cyclocomputer may not be possible due to the inuence of the ●
2.4 GHz frequency band. If pairing fails, try again someplace where there is no
inter ference from microwaves, radio waves, or wireless equipment.
Do not use magnets other than the enclosed ones. ●
Installing the Cadence Magnet
Remove the pedal from the
1.
crank.
Install the cadence magnet to
2.
the crank.
14
Install it so the magnet part is facing to
the chain stay side.
Chain stay
Magnet
The magnet can be installed to a •
crank that is from about 90 mm up to
100 mm in circumference.
Be careful not to get injured when •
installing the cadence magnet.
After installing the cadence magnet, •
conrm that it is not cracked. If it is
cracked, do not use it.
Page 15
Installation on Your Bike
Installing the
Speed & Cadence Sensor
Temporarily mount the Speed
1.
& Cadence sensor on the
chain stay.
Hook the band on the hook located on
the back side of the sensor, and then
put the band in the groove on the front
side to temporarily mount the sensor
on the chain stay.
The sensor can be installed to a •
chain stay that is from about 100 mm
up to 120 mm in circumference.
The sensor cannot be installed •
securely on some chain stays’
shapes. Conrm the chain stay’s
shape when installing it.
Do not pull the band too strongly. •
Doing so may break the band.
Adjust the location of the
2.
Speed & Cadence sensor.
A
djust the sensor by tilting it so the
center of the cadence magnet passes
about 3 mm from the sensor part
(concave par t) of the Speed & Cadence
sensor when the crank is rotated.
3 mm
When the sensor detects the cadence
magnet as the cranks are rotated,
the LED blinks green every time it is
detected, up to 10 times.
EN
15
Page 16
Installation on Your Bike
EN
After blinking 10 times, the LED will •
not light even though the sensor
detects the magnet. The LED starts
blinking again if you re-install the
sensor ’s batter y or wait at least 20
minutes af ter the last time the sensor
detects the magnet.
Installing the Speed Magnet
Loosen the screw of the
1.
speed magnet and remove
the magnet part.
Install the speed magnet to
2.
the spoke of the back wheel.
16
Page 17
Installation on Your Bike
The magnet can be installed on a •
spoke that is from about 1.5 mm up
to 2.5 mm in diameter.
The magnet cannot be installed securely •
on some spokes’ shapes. Conr m the
spoke’s shape when installing it.
Installing the magnet may damage •
the spoke. Protect the spoke if you
do not want to damage it.
Be careful not to lose the sheet and •
so on, when installing the magnet.
After installing the magnet, check •
that its sc rew has not been screwed
in at an angle.
Adjust the angle of the speed
3.
detector arm.
Adjust the angle of the arm by turning
the hex screw so the center of the
speed magnet passes about 3 mm
from the sensor par t (concave part) of
the arm when the wheel is rotated.
3 mm
When the sensor detects the speed
magnet as the wheel rotates, the LED
blinks red up to 10 times each time it is
detected.
Install the sensor so the arm does •
not inter fere with the spokes.
Do not move the arm beyond its •
range of motion (60°).
60°
After blinking 10 times, the LED will •
not light even though the sensor
detects the magnet. The LED starts
blinking again if you re-install the
sensor ’s batter y or wait at least 20
minutes af ter the last time the sensor
detects the magnet.
Speed is not detected until you •
tighten the angle adjustment screw
of the arm.
EN
17
Page 18
Installation on Your Bike
Fixing the Sensor
EN
After installing the Speed & Cadence
sensor, cadence magnet, and speed
magnet, pair the sensor with the
Cyclocomputer SGX-CA500 or other
cyclocomputer, and conrm that
the cadence is displayed with the
rotation of the crank, and the speed
is displayed with the rotation of the
wheel. Refer to the Quick Start Guide
of the Cyclocomputer SGX-CA500 or
your cyclocomputer’s owner manual for
sensor pairing.
After conrming that the information
from the Speed & Cadence sensor is
displayed correctly, x the band with
the xing tape for the sensor’s band.
After xing the Speed & Cadence
sensor, install the pedal to the crank.
Be sure to use the xing tape. If •
you do not use the xing tape, the
sensor ’s band may slip off and the
sensor may fall off during a ride.
Do not re-use the xing tape. The •
used xing tape may come off during
a ride because its adhesion has
decreased.
Securely x the Speed & Cadence •
sensor to the chain stay so it does
not fall towards the crank or spokes
while riding.
Before riding, check that the sensor •
and magnets are installed securely.
Also check that the speed detector
arm’s screw is not loose, there are
no cracks in the band, and the band’s
xing tape is not coming off.
When the sensor or magnets •
become soiled with mud or any thing
else, wipe them off.
18
Page 19
Installing and Removing the Battery
The batter y is pre-installed to this product. If the battery is almost empty (see
page 21), replace the battery with new one.
Remove the battery cover of
1.
the Speed & Cadence sensor.
Turn the cover counterclockwise with a
tool such as a coin or screwdriver, until
it stops turning.
Remove the old battery.
2.
Install the new battery
3.
(CR2032) and close the
battery cover.
Insert the battery with its (-) side facing
up and wait more than 3 seconds to
remove it. Then insert it with its (+) side
facing up. Doing this resets the sensor
so it operates reliably.
Then turn the battery cover clockwise
until it stops and is closed tightly.
Be careful not to lose the rubber •
gaskets when removing the battery
co ver.
Rubber
gaskets
EN
19
Page 20
Installing and Removing the Battery
EN
Be careful not to drop or lose the •
batter y when installing it.Do not use
batteries other than CR2032.
Install the cover r mly to ensure •
water resistant per formance.
If a mud or water is on the bat tery •
cover, wipe it of f with a dr y cloth
before removing the cover. Do not
touch the cover with wet hands.
When disposing of used batteries, •
please comply with governmental
regulations or environmental public
institutions rules that apply in your
countr y or area.
Keep coin batteries out of reach of •
children.
20
Page 21
Troubleshooting
If you have problems with your device, check the following items.
If a solution to your problem cannot be found here, contact your dealer.
Speed & Cadence sensor information is not displayed on the cyclocomputer. / ■
I cannot pair the sensor with the cyclocomputer.
Cause Solution
Sensitivity of the sensor has become
low due to dir t such as mud on the
sensor or magnets.
The battery is almost empt y. Replace the battery with a new one (see page 19).
(+) or (-) side of the bat tery is
installed in the opposite side.
The battery is not installed correctly. Install the battery again (see page 19).
The sensor is not mounted correctly. Conrm the position of the sensor and magnets, and the
Pairing between the sensor and the
cyclocomputer has not been done.
Sensor has not been reset. Install the battery with its (+) side down and wait more than
Connection is not possible due
to the inuence of the 2.4 GHz
frequency band.
Wipe off dirt from the sensor or magnets.
Install the battery in the proper side (see page 19).
distanc e between them (see page 15, 16).
Check if the sensor is paired with the cyclocomputer.
If not, pair them. Refer to the Quick Star t Guide of the
Cycloc omputer SGX-CA500 or your cycloc omputer’s owner
manual for sensor pairing.
3 seconds, then remove the battery. The sensor is reset in
this way.
Try pairing again someplace where there is no inter ferenc e
from microwaves, Wi-Fi such as a wireless LAN, or other
wireless ANT equipment.
Speed is not displayed. ■
Cause Solution
The screw of the speed detector arm
is loose.
Tighten the screw of the speed detector ar m so it is not
loose. Speed is not detected if the screw is loose.
EN
21
Page 22
Specications
Weight: Sensor:
EN
Dimensions: Sensor:
Water resistant: This device is water resistant to 6 m.
Communications method (sensors): ANT+ wireless
Battery: CR2032
Operation temperature: -10 to 60°C
Estimated usable period: About 3 years (at one hour per day of use)
ANT+ is a Wireless Personal Network protocol with very low power •
requirements using 2.4GHz frequency band.
For more information, visit http://www.thisisant.com/
Specications and design are subject to change without notice.•
Illustrations used in this manual may be different from actual appearance.•
About 24 g
36 mm(W) x 42 mm (H) x 16.5 mm(D)
22
Page 23
http://www.pioneerelectronics.com
http://www.pioneerelectronics.ca
Visit www.pioneer.eu to register your product.
Visitez w ww.pioneer.eu pour enregistrer votre appareil.
PIONEER CORPORATION
1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, JAPAN
PIONEER ELECTRONICS (USA) INC.
P.O. Box 1540, Long Beach, California, 90801-1540, U.S.A.
TEL: (800) 421-1404
PIONEER ELECTRONICS OF CANADA INC.
340 Ferrier Street, Unit 2, Markham, Ontario, L3R 2Z5, Canada
TEL: 1-877-283-5901
TEL: 905-479-4411
©2014 PIONEER CORPORATION.
All rights reserved.
5615N4630006R00
Loading...