Pioneer DEH-X26UI, DEH-X2600UI, DEH-X3600UI, DEH-X36UI User Manual

CD RDS RECEIVER AUTORADIO CD RDS REPRODUCTOR DE CD CON RECEPTOR RDS

DEH-X3600UI DEH-X36UI DEH-X2600UI DEH-X26UI

Owner’s Manual

Mode d’emploi

Manual de instrucciones

Important (Serial number)

The serial number is located on the bottom of this unit. For your own security and convenience, be sure to record this number on the enclosed warranty card.

Important (Numéro de série)

Le numéro de série se trouve au bas de cet appareil. Pour votre sécurité et votre commodité, veillez à noter ce numéro sur la carte de garantie fournie.

Importante (Número de serie)

El número de serie se encuentra en la parte inferior de esta unidad. Por su propia seguridad y comodidad, asegúrese de anotar este número en la tarjeta de garantía que se adjunta.

English EspañolFrançais

Section

Before you start

Thank you for purchasing this PIONEER product

To ensureproperuse,please read through this manual before using this product. It is especially important that you read and obser ve WARN-

INGs and CAUTIONs in this manual. Please keep the manual in a safe and accessible place for future reference.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Information to User

Alteration or modifications carried out without appropriate authorization may invalidate the user ’s right to operate the equipment.

Note

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/ TV technician for help.

The Safety of Your Ears is in Your Hands

Get the most out of your equipment by playing it at a safe level—a level that lets the sound come through clearly without annoying blaring or distortion and, most importantly, without affecting your sensitive hearing. Sound can be deceiving. Over time, your hearing “comfort level” adapts to higher volumes of sound, so what sounds “normal” can actually be loud and harmful to your hearing. Guard against this by setting your equipment at a safe level BEFORE your hearing adapts.

ESTABLISH A SAFE LEVEL:

! Set your volume control at a low setting. ! Slowly increase the sound until you can hear

it comfortably and clearly, without distortion.

! Once you have established a comfortable

sound level, set the dial and leave it there.

BE SURE TO OBSERVE THE FOLLOWING GUIDELINES:

! Do not turn up the volume so high that you

can’t hear what’s around you.

! Use caution or temporarily discontinue use

in potentially hazardous situations.

! Do not use headphones while operating a

motorized vehicle; the use of headphones may create a traffic hazard and is illegal in many areas.

About this unit

The tuner frequencies on this unit are allocated for use in North America. Use in other areas may result in poor reception.

WARNING

! Do not attempt to install or service this

product by yourself. Installation or servicing of this product by persons without training and experience in electronic equipment and automotive accessories may be dangerous and could expose you to the risk of electric shock, injury or other hazards.

! Do not attempt to operate the unit while driv-

ing. Make sure to pull off the road and park your vehicle in a safe location before attempting to use the controls on the device.

! Handling the cord on this product or cords

associated with accessories sold with the product may expose you to chemicals listed on proposition 65 known to the State of California and other governmental entities to cause cancer and birth defect or other reproductive harm. Wash hands after handling.

CAUTION: USE OF CONTROL OR ADJUSTMENT OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. CAUTION: THE USE OF OPTICAL INSTRUMENTS WITH THIS PRODUCT WILL INCREASE EYE HAZARD.

CAUTION

! Do not allow this unit to come into contact

with liquids. Electrical shock could result. Also, damage to this unit, smoke, and overheating could result from contact with liquids.

! Always keep the volume low enough to hear

outside sounds.

! Avoid exposure to moisture.

CAUTION

This product is a class 1 laser product classified under the Safety of laser products, IEC 60825-1:2007.

d8 9 e

9 de

Before you start

After-sales service for Pioneer products

Please contact the dealer or distributor from where you purchased this unit for after-sales service (including warranty conditions) or any other information. In case the necessary information is not available, please contact the companies listed below: Please do not ship your unit to the companies at the addresses listed below for repair without advance contact.

U.S.A.

Pioneer Electronics (USA) Inc. CUSTOMER SUPPORT DIVISION P.O. Box 1760 Long Beach, CA 90801-1760 800-421-1404

CANADA

Pioneer Electronics of Canada, Inc. CUSTOMER SATISFACTION DEPARTMENT 340 Ferrier Street Unit 2 Markham, Ontario L3R 2Z5, Canada 1-877-283-5901 905-479-4411

For warranty information please see the Limited Warranty sheet included with this unit.

If you experience problems

Should this unit fail to work properly, please contact your dealer or nearest authorized PIONEER Service Station.

Using this unit

Head unit

DEH-X3600UI/DEH-X36UI

2 4

DEH-X2600UI/DEH-X26UI

1 SRC/OFF

2 h (eject)

3 MULTI-CONTROL (M.C.)

(list)

5 Disc loading slot

6 USB port

MIX (MIXTRAX) DEH-X3600UI/DEH-X36UI

iPod

DEH-X2600UI/DEH-X26UI

8 BAND/

a c/d

b DISP

b c

(iPod control)

(back)/DIMMER (dimmer)

Section

c 1/

to 6/

d AUX input jack (3.5 mm stereo jack)

62 4 5

e Detach button

CAUTION

Use an optional Pioneer USB cable (CD-U50E) to connect the USB storage device as any device connected directly to the unit will protrude out from the unit, which could be dangerous.

Remote control

a 8

m l

g h i

VOLUME

Press to increase or decrease volume.

MUTE

Press to mute. Press again to unmute.

a/b

Press to recall preset stations. Press to select the next/previous folder.

AUDIO

Press to select an audio function.

DISP/SCRL

Press to select different displays. Press and hold to turn dimmer on or off.

English

9754

3 6 8

Section

Using this unit

Press to pause or resume playback.

FUNCTION

Press to select functions.

LIST/ENTER Press to display the list depending on the

source. While in the operating menu, press to control functions.

Display indication

DEH-X3600UI/DEH-X36UI

DEH-X2600UI/DEH-X26UI

9 5 7

43 86

Main information section ! Tuner: band and frequency

! CD player, USB storage device and iPod:

elapsed playback time and text information

Appears when a lower tier of folder or menu

exists.

(list)

4 Sub information section

5 LOC (local seek tuning)

(sound retriever)

(random/shuffle)

(repeat)

(iPod control) This unit’s iPod function is operated from your iPod.

Set up menu

1 After installation of this unit, turn the ignition switch to ON. SET UP appears.

2 Turn M.C. to switch to YES.

# If you do not use the unit for 30 seconds, the set up menu will not be displayed. # If you prefer not to set up at this time, turn M.C. to switch to NO.

3 Press M.C. to select.

4 Complete the procedure outlined below to set the menu.

To proceed to the next menu option, you need to confirm your selection.

CLOCK SET (setting the clock)

1 Turn M.C. to adjust hour. 2 Press M.C. to select minute. 3 Turn M.C. to adjust minute. 4 Press M.C. to confirm the selection.

QUIT appears.

5 To finish your settings, turn M.C. to select YES.

# If you prefer to change your setting again, turn

M.C. to switch to NO.

6 Press M.C. to select.

Notes

! You can set up the menu options from the

system menu. For details about the settings, refer to System menu on page 11.

! You can cancel set up menu by pressing

SRC/OFF.

Basic operations

Important

! Handle the front panel with care when re-

moving or attaching it.

! Avoid subjecting the front panel to excessive

shock.

! Keep the front panel out of direct sunlight

and high temperatures.

! To avoid damaging the device or vehicle inte-

rior, remove any cables and devices attached to the front panel before detaching it.

Removing the front panel 1 Press the detach button to release the front

panel.

2 Push the front panel upward (M) and then pull

it toward (N) you.

3 Always store the detached front panel in a pro-

tective case or bag.

Re-attaching the front panel

1 Slide the front panel to the left.

2 Press the right side of the front panel until it is

firmly seated. Forcing the front panel into place may result in damage to the front panel or head unit.

Turning the unit on 1 Press SRC/OFF to turn the unit on.

Turning the unit off 1 Press and hold SRC/OFF until the unit turns

off.

Using this unit

Section

Selecting a source

1 Press SRC/OFF to cycle between:

RADIO—CD—USB/iPod—PANDORA—APP (application)—AUX

! USB MTP displays while the MTP connection

is in use.

! Only for DEH-X2600UI and DEH-X26UI

When there is an iPod connected and a source other than iPod is selected, you can switch to iPod by pressing iPod.

Adjusting the volume 1 Turn M.C. to adjust the volume.

Note

When this unit’s blue/white lead is connected to the vehicle’s auto-antenna relay control terminal, the vehicle’s antenna extends when this unit’s source is turned on. To retract the antenna, turn the source off.

Use and care of the remote control

Using the remote control 1 Point the remote control in the direction of the

front panel to operate. When using for the first time, pull out the film protruding from the tray.

Replacing the battery 1 Slide the tray out on the back of the remote

control.

2 Insert the battery with the plus (+) and minus

(–) poles aligned properly.

WARNING

! Keep the battery out of the reach of children.

Should the battery be swallowed, consult a doctor immediately.

! Batteries (battery pack or batteries installed)

must not be exposed to excessive heat such as sunshine, fire or the like.

CAUTION

! Remove the battery if the remote control is

not used for a month or longer.

! There is a danger of explosion if the battery is

incorrectly replaced. Replace only with the same or equivalent type.

! Do not handle the battery with metallic tools. ! Do not store the battery with metallic ob-

jects.

! If the battery leaks, wipe the remote control

completely clean and install a new battery.

! When disposing of used batteries, comply

with governmental regulations or environmental public institutions’ rules that apply in your country/area.

! “Perchlorate Material – special handling may

apply. See

www.dtsc.ca.gov/hazardouswaste/ perchlorate. (Applicable to California, U.S.A.)”

Important

! Do not store the remote control in high tem-

peratures or direct sunlight.

! The remote control may not function properly

in direct sunlight.

! Do not let the remote control fall onto the

floor, where it may become jammed under the brake or accelerator pedal.

Frequently used menu operations

Returning to the previous display Returning to the previous list (the folder one level higher)

/DIMMER.

1 Press

Returning to the ordinary display Canceling the main menu 1 Press BAND/

Returning to the ordinary display from the list 1 Press BAND/

Radio

Basic operations

Selecting a band

1 Press BAND/

FM2, FM3 for FM or AM) is displayed.

Switching preset stations 1 Press c or d. ! Select PCH (preset channel) under SEEK to

use this function.

! Use the a and b on the remote control to

switch between preset stations.

Manual tuning (step by step) 1 Press c or d. ! Select MAN (manual tuning) under SEEK to

use this function.

Seeking 1 Press and hold c or d, and then release.

You can cancel seek tuning by briefly pressing c or d. While pressing and holding c or d, you can skip stations. Seek tuning starts as soon as you release c or d.

until the desired band (FM1,

Note

For details about SEEK, refer to SEEK (left/right key setting) on page 6.

Storing and recalling stations for each band

Using preset tuning buttons

1 To store: Press and hold down one of the preset tuning buttons (1/ the number stops flashing.

2 To recall: Press one of the preset tuning buttons (1/

to 6/ ).

to 6/ ) until

Switching the display

Selecting the desired text information 1 Press DISP to cycle between the following:

! FREQUENCY (program ser vice name or

frequency)

! BRDCST INFO (song title/artist name) ! CLOCK (source name and clock)

Notes

! If the program service name cannot be ac-

quired in FREQUENCY, the broadcast frequency is displayed instead. If the program service name is detected, the program service name will be displayed.

! Depending on the band, text information can

be changed.

! Text information items that can be changed

depend on the area.

Function settings

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option and press to select FUNCTION.

English

Section

Using this unit

3 Turn M.C. to select the function.

Once selected, the following functions can be adjusted.

BSM (best stations memory)

BSM (best stations memory) automatically stores the six strongest stations in the order of their signal strength. 1 Press M.C. to turn BSM on.

To cancel, press M.C. again.

LOCAL (local seek tuning)

Local seek tuning allows you to tune in to only those radio stations with sufficiently strong signals for good reception. 1 Press M.C. to select the desired setting.

FM: OFF—LV 1 —LV2 —LV3 —LV4 AM: OFF—LV 1 —LV2 The highest level setting allows reception of only the strongest stations, while lower levels allow the reception of weaker stations.

SEEK (left/right key setting)

You can assign a function to the left and right keys of the unit. Select MAN (manual tuning) to tune up or down manually or select PCH (preset channel) to switch between preset channels. 1 Press M.C. to select MAN or PCH.

CD/CD-R/CD-RW and USB storage devices

MTP connection

MTP-compatible Android devices (running Android OS 4.0 or higher) can be connected by MTP connection using the USB source. To connect an Android device, use the cable that came with the device.

Notes

! This function is not compatible with MIX-

TRAX.

! This function is not compatible with WAV.

Basic operations

Playing a CD/CD-R/CD-RW 1 Insert the disc into the disc loading slot with

the label side up.

Ejecting a CD/CD-R/CD-RW 1 Press h.

Playing songs on a USB storage device

1 Open the USB port cover. 2 Plug in the USB storage device using a USB

cable.

Stopping playback of files on a USB storage device 1 Youmay disconnect the USB storage device at

any time.

Selecting a folder 1 Press 1/

Selecting a track 1 Press c or d.

Fast forwarding or reversing 1 Press and hold c or d. ! When playing compressed audio, there is no

Returning to root folder 1 Press and hold BAND/

Switching between compressed audio and CD-DA 1 Press BAND/

Switching between playback memory devices You can switch between playback memory devices on USB storage devices with more than one Mass Storage Device-compatible memory device. 1 Press BAND/ ! You can switch between up to 32 different

or 2/ .

sound during fast forward or reverse.

memory devices.

Note

Disconnect USB storage devices from the unit when not in use.

Operations using the MIXTRAX button

Turning MIXTRAX on or off You can use this function when USB is selected as the source. You cannot use this function with USB MTP. DEH-X3600UI/DEH-X36UI 1 Press MIX to turn MIXTRAX on or off. DEH-X2600UI/DEH-X26UI 1 Press 3/MIX to turn MIXTRAX on or off. ! For more details about MIXTRAX, refer to

About MIXTRAX on page 12.

! When MIXTRAX is in use, the sound retriever

function is disabled.

Switching the display

Selecting the desired text information 1 Press DISP to cycle between the following:

CD-DA

! ELAPSED TIME (track number and play-

back time)

! CLOCK (source name and clock) ! SPEANA (spectrum analyzer)

CD-TEXT

! TRACK INFO (track title/track artist/disc

title)

! ELAPSED TIME (track number and play-

back time)

! CLOCK (source name and clock) ! SPEANA (spectrum analyzer)

MP3/WMA/WAV

! TRACK INFO (track title/artist name/album

title)

! FILE INFO (file name/folder name) ! ELAPSED TIME (track number and play-

back time)

! CLOCK (source name and clock) ! SPEANA (spectrum analyzer)

Selecting and playing files/ tracks from the name list

1 Press to switch to the file/track name list mode.

2 Use M.C. to select the desired file name (or folder name).

Selecting a file or folder 1 Turn M.C.

Playing 1 When a file or track is selected, press M.C.

Using this unit

Section

Viewing a list of the files (or folders) in the selected folder 1 When a folder is selected, press M.C.

Playing a song in the selected folder 1 When a folder is selected, press and hold M.C.

Operations using special buttons

Selecting a repeat play range 1 Press 6/

Playing tracks in random order 1 Press 5/

! To change songs during random play, press d

Pausing playback 1 Press 4/PAUSE to pause or resume.

Enhancing compressed audio and restoring rich sound (sound retriever)

Only for DEH-X3600UI and DEH-X36UI

1 Press 3/S.Rtrv to cycle between:

! Key operation is disabled when MIXTRAX is

to cycle between the following:

CD/CD-R/CD-RW

! ALL – Repeat all tracks ! ONE – Repeat the current track ! FLD – Repeat the current folder

USB storage device

! ALL – Repeat all files ! ONE – Repeat the current file ! FLD – Repeat the current folder

to turn random play on or off. Tracks in a selected repeat range are played in random order.

to switch to the next track. Pressing c restarts playback of the current track from the beginning of the song.

1—2—OFF (off) 1 is effective for low compression rates, and 2

is effective for high compression rates.

on.

Function settings

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option and press to select FUNCTION.

Once selected, the function below can be adjusted.

! S.RTRV is not available when MIXTRAX is

turned on.

S.RTRV (sound retriever)

Automatically enhances compressed audio and restores rich sound. 1 Press M.C. to select the desired setting.

For details, refer to Enhancing compressed

audio and restoring rich sound (sound retriever)

on page 7.

iPod

Basic operations

Playing songs on an iPod

1 Open the USB port cover. 2 Connect an iPod to USB input.

Playback is performed automatically.

Selecting a song (chapter) 1 Press c or d.

Selecting an album 1 Press 1/

Fast forwarding or reversing 1 Press and hold c or d.

Notes

! The iPod cannot be turned on or off when the

! Disconnect headphones from the iPod be-

or 2/ .

control mode is set to CONTROL AUDIO/CTRL AUDIO.

fore connecting it to this unit.

! The iPod will turn off about two minutes after

the ignition is switched off.

Operations using the MIXTRAX button

Turning MIXTRAX on or off DEH-X3600UI/DEH-X36UI 1 Press MIX to turn MIXTRAX on or off. DEH-X2600UI/DEH-X26UI 1 Press 3/MIX to turn MIXTRAX on or off. ! For more details about MIXTRAX, refer to

About MIXTRAX on page 12.

Switching the display

Selecting the desired text information 1 Press DISP to cycle between the following:

! TRACK INFO (track title/artist name/album

title)

! ELAPSED TIME (track number and play-

back time)

! CLOCK (source name and clock) ! SPEANA (spectrum analyzer)

Browsing for a song

1 Press to switch to the top menu of list search.

2 Use M.C. to select a category/song.

Changing the name of the song or category 1 Turn M.C.

Playlists—artists—albums—songs—podcasts —genres—composers—audiobooks

Playing 1 When a song is selected, press M.C.

Viewing a list of songs in the selected category 1 When a category is selected, press M.C.

Playing a song in the selected category 1 When a category is selected, press and hold

M.C.

Searching the list by alphabet 1 When a list for the selected category is dis-

played, press mode. ! You also can switch to alphabet search

mode by turning M.C. twice.

2 Turn M.C. to select a letter. 3 Press M.C. to display the alphabetical list.

! To cancel searching, press

to switch to alphabet search

/DIMMER.

Notes

! You can play playlists created with the com-

puter application (MusicSphere). The application will be available on our website.

! Playlists that you created with the computer

application (MusicSphere) are displayed in abbreviated form.

Operations using special buttons

Selecting a repeat play range 1 Press 6/

! When the control mode is set to CONTROL

Selecting a random play range (shuffle) 1 Press 5/

to cycle between the following:

! ONE – Repeat the current song ! ALL – Repeat all songs in the selected list

iPod/CTRL iPod, the repeat play range will be same as what is set for the connected iPod.

to cycle between the following:

! SNG – Play back songs in the selected list

in random order.

! ALB – Play back songs from a randomly se-

lected album in order.

! OFF – Not play back in random order.

English

Section

Using this unit

Playing all songs in random order (shuffle all) 1 Press and hold 5/ ! To turn off shuffle all, select OFF in shuffle. For

details, refer to Selecting a random play range (shuffle) on page 7.

Pausing playback 1 Press 4/PAUSE to pause or resume.

Enhancing compressed audio and restoring rich sound (sound retriever)

Only for DEH-X3600UI and DEH-X36UI

1 Press 3/S.Rtrv to cycle between:

1—2—OFF (off) 1 is effective for low compression rates, and 2

is effective for high compression rates.

to turn shuffle all on.

Playing songs related to the currently playing song

You can play songs from the following lists.

• Album list of the currently playing artist

• Song list of the currently playing album

• Album list of the currently playing genre

1 Press and hold mode.

2 Turn M.C. to change the mode; press to select.

! ARTIST – Plays an album by the artist cur-

rently playing.

! ALBUM – Plays a song from the album cur-

rently being played.

! GENRE – Plays an album from the genre cur-

rently being played.

The selected song/album will be played after the currently playing song.

Notes

! The selected song/album may be canceled if

you use functions other than link search (e.g. fast forward and reverse).

to switch to link play

! Depending on the song selected to play, the

end of the currently playing song and the beginning of the selected song/album may be cut off.

Using this unit’s iPod function from your iPod

This unit’s iPod function can be controlled by using the connected iPod. CONTROL iPod/CTRL iPod is not compatible with the following iPod models.

! iPod nano 1st generation ! iPod with video

% Press BAND/

mode.

! CONTROL iPod/CTRL iPod – This unit’siPod

function can be operated from the connected iPod.

! CONTROL AUDIO/CTRL AUDIO – This unit’s

iPod function can be controlled by using this unit.

Only for DEH-X2600UI and DEH-X26UI

You can also switch the control mode by pressing iPod.

to switch the control

Notes

! Switching the control mode to

CONTROL iPod/CTRL iPod pauses song playback. Use the iPod to resume playback.

! The following operations are still accessible

from the unit even if the control mode is set to CONTROL iPod/CTRL iPod.

— Pausing — Fast forward/reverse — Selecting a song (chapter)

! The volume can only be adjusted from this

unit.

Function settings

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option and press to select FUNCTION.

3 Turn M.C. to select the function.

Once selected, the following functions can be adjusted.

! AUDIO BOOK is not available when

CONTROL iPod/CTRL iPod is selected in the

control mode. For details, refer to Using this unit’s iPod function from your iPod on page 8.

AUDIO BOOK (audiobook speed)

1 Press M.C. to display the setting mode. 2 Turn M.C. to select your favorite setting.

! FASTER – Playback at a speed faster than

normal

! NORMAL – Playback at normal speed ! SLOWER – Playback at a speed slower

than normal

S.RTRV (sound retriever)

1 Press M.C. to select the desired setting.

For details, refer to Enhancing compressed

audio and restoring rich sound (sound retriever)

on page 8.

Streaming Pandora

IMPORTANT:

Requirements to access Pandora using the Pioneer car audio/video products:

! Please update the firmware of the Pandora appli-

cation to the latest version before use.

! The latest version of the Pandora application can

be downloaded on iTunes App Store.

! Create a free or a paid account online. You can

create the account in the Pandora application from your iPhone or on the website. The URL in the following: http://www.pandora.com/register

! If the Data Plan for your iPhone does not provide

for unlimited data usage, additional charges from your carrier may apply for accessing the Pandora service via 3G and/or EDGE networks.

! You need to connect to the Internet via 3G, EDGE

or Wi-Fi network to use the service from Pandora.

Limitations:

! Depending on the availability to the Internet, you

may not be able to receive Pandora service.

! Pandora service is subject to change without no-

tice. The service could be affected by any of the following: firmware versions of iPhone, firmware versions of Pandora application, changes to the Pandora music service.

! Certain functions of the Pandora service are not

available when accessing the service through the Pioneer car audio/video products. They include, but not limited to the following: creating new stations, deleting stations, sending information about current stations, buying tracks from iTunes,viewing additional text information, logging in to Pandora, adjusting Cell Network Audio Quality.

Pandora internet radio is a music service not affiliated with Pioneer. More information is available at http://www.pandora.com. The Pandora mobile application is available for most iPhone and smartphone, please visit www.pandora.com/everywhere/mobile for the latest compatibility information.

Starting procedure for iPhone users

1 Connect an iPhone to USB input.

2 Switch the source to PANDORA.

3 Start up the application on the iPhone and initiate playback.

Using this unit

Section

Basic operations

Playing tracks For details, refer to Starting procedure for iPhone users on page 8.

Skipping tracks 1 Press d.

Switching the display

Selecting the desired text information 1 Press DISP to cycle between the following:

! TRACK INFO (station name/track title/ar-

tist name/album title)

! ELAPSED TIME (playback time) ! CLOCK (source name and clock) ! SPEANA (spectrum analyzer)

Note

Depending on the station, text information can be changed.

Selecting and playing the Shuffle/station list

The display shown on this unit may not be the same as that shown on the connected device.

1 Press tion list mode.

(list) to switch to the Shuffle/sta-

2 Use M.C. to select the Shuffle or desired station.

Changing the sort order 1 Press

! ABC – You can sort the items in the list alpha-

! DATE – You can sort the items in the list in

Changing Shuffle or stations 1 Turn M.C.

Playing 1 When Shuffle or the station is selected, press

Deleting stations

1 When station is selected, press and hold M.C.

2 Press M.C.

(list).

betically

order of the dates on which the items were created

M.C.

DELETE YES appears.

To cancel, press to the previous level.

The station will be deleted.

/DIMMER. You will return

Operations using special buttons

Pausing playback 1 Press 4/PAUSE to pause or resume.

Enhancing compressed audio and restoring rich sound (sound retriever)

Only for DEH-X3600UI and DEH-X36UI

1 Press 3/S.Rtrv to cycle between:

1—2—OFF (off) 1 is effective for low compression rates, and 2

is effective for high compression rates.

Giving a Thumbs Down 1 Press 2/

Giving a Thumbs Up 1 Press 1/

to give a “Thumbs Down” for the track currently playing and to skip to the next track.

to give a “Thumbs Up” for the track currently playing.

Function settings

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option and press to select FUNCTION.

3 Turn M.C. to select the function.

Once selected, the following functions can be adjusted.

BOOKMARK (bookmark)

1 Press M.C. to store track information.

NEW STATION (new station)

A new station will be created from the information for the artist or track of the station currently being played.

1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting.

FROM TRACK (from track)—FROM ARTIST (from artist)

3 Press M.C.

A new station is created.

! You can also create a new station from a track

by pressing and holding down 5/

! You can also create a new station from an ar-

tist by pressing and holding down 6/

S.RTRV (sound retriever)

1 Press M.C. to select the desired setting.

For details, refer to Enhancing compressed

audio and restoring rich sound (sound retriever)

on page 9.

Using connected device applications

You can use this unit to perform streaming playback of and control tracks in iPhone applications or just for streaming playback.

Important

Use of third party apps may involve or require the provision of personally identifiable information, whether through the creation of a user account or otherwise, and for certain applications, the provision of geolocation data. ALL THIRD PARTY APPS ARE THE SOLE RESPONSIBILITY OF THE PROVIDERS, INCLUDING WITHOUT LIMITATION COLLECTION AND SECURITY OF USER DATA AND PRIVACY PRACTICES. BY ACCESSING THIRD PARTY APPS, YOU AGREE TO REVIEW THE TERMS OF SERVICE AND PRIVACY POLICIES OF THE PROVIDERS. IF YOU DO NOT AGREE WITH THE TERMS OR POLICIES OF ANY PROVIDER OR DO NOT CONSENT TO THE USE OF GEOLOCATION DATAWHERE APPLICABLE, DO NOT USE THAT THIRD PARTY APP.

Information for compatibility of connected devices

The following is the detailed information regarding the terminals required to use the application for iPhone on this unit.

English

Section

Using this unit

For iPhone users

! This function is compatible with iPhone and

iPod touch.

! The device has iOS 5.0 or higher.

Notes

! Please check our website for a list of sup-

ported iPhone applications for this unit.

! Pioneer is not liable for any issues that may

arise from incorrect or flawed app-based content.

! The content and functionality of the sup-

ported applications are the responsibility of the App providers.

Starting procedure for iPhone users

1 Connect an iPhone to USB input.

2 Switch the source to APP.

3 Start up the application on the iPhone and initiate playback.

Basic operations

Selecting a track 1 Press c or d.

Fast forwarding or reversing 1 Press and hold c or d.

Pausing playback 1 Press BAND/

to pause or resume.

Switching the display

Selecting the desired text information 1 Press DISP to cycle between the following:

! TRACK INFO (track title/artist name/album

title)

! APP NAME (application name) ! ELAPSED TIME (playback time) ! CLOCK (source name and clock) ! SPEANA (spectrum analyzer)

Function settings

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option and press to select FUNCTION.

3 Turn M.C. to select the function.

Once selected, the following functions can be adjusted.

PAUSE (pause)

1 Press M.C. to pause or resume.

S.RTRV (sound retriever)

1 Press M.C. to select the desired setting.

1—2—OFF (off) 1 is effective for low compression rates, and 2

is effective for high compression rates.

Audio adjustments

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option and press to select AUDIO.

3 Turn M.C. to select the audio function.

Once selected, the following audio functions can be adjusted.

! FADER is not available when SUB.W/SUB.W

is selected in SP-P/O MODE. For details, refer to SP-P/O MODE (rear output and preout set- ting) on page 12.

! SUB.W and SUB.W CTRL are not available

when REAR/REAR is selected in

SP-P/O MODE. For details, refer to SP-P/O MODE (rear output and preout set-

ting) on page 12.

! SUB.W CTRL is not available when SUB.W is

selected in OFF. For details, refer to SUB.W (subwoofer on/off setting) on page 10.

! SLA is not available when FM is selected as

the source.

FADER (fader adjustment)

1 Press M.C. to display the setting mode. 2 Turn M.C. to adjust the front/rear speaker bal-

ance.

BALANCE (balance adjustment)

1 Press M.C. to display the setting mode. 2 Turn M.C. to adjust the left/right speaker bal-

ance.

EQ SETTING (equalizer recall)

1 Press M.C. to display the setting mode. 2 Turn M.C. to select the equalizer.

POWERFUL—NATURAL—VOCAL—CUSTOM1—CUSTOM2—FLAT—SUPER BASS

The equalizer band and equalizer level can be customized when CUSTOM1 or CUSTOM2 is selected. If selecting CUSTOM1 or CUSTOM2, complete the procedures outlined below. If selecting other options, press M.C. to return to the previous display. ! CUSTOM1 can be set separately for each

source. However, USB, iPod, PANDORA and APP are all set to the same setting automatically.

! CUSTOM2 is a shared setting used in com-

mon for all sources.

3 Press M.C. to display the setting mode. 4 Press M.C. to cycle between the following:

Equalizer band—Equalizer level

5 Turn M.C. to select the desired setting.

Equalizer band: 80HZ—250HZ—800HZ—

2.5KHZ—8KHZ Equalizer level: +6 to –6

LOUDNESS (loudness)

Loudness compensates for deficiencies in the lowfrequency and high-frequency ranges at low volume.

1 Press M.C. to select the desired setting.

OFF (off)—LOW (low)—MID (mid)—HI (high)

SUB.W (subwoofer on/off setting)

This unit is equipped with a subwoofer output which can be turned on or off.

1 Press M.C. to select the desired setting.

NOR (normal phase)—REV (reverse phase)— OFF (subwoofer off)

SUB.W CTRL (subwoofer adjustment)

Using this unit

Section

Only frequencies lower than those in the selected range are outputted from the subwoofer.

1 Press M.C. to display the setting mode. 2 Press M.C. to cycle between the following:

Cut-off frequency—Output level—Slope level Rates that can be adjusted will flash.

3 Turn M.C. to select the desired setting.

Cut-off frequency: 50HZ—63HZ—80HZ—

100HZ—125HZ—160HZ—200HZ

Output level: –24 to +6 Slope level: –12— –24

BASS BOOST (bass boost)

1 Press M.C. to display the setting mode. 2 Turn M.C. to select a desired level.

0 to +6 is displayed as the level is increased or decreased.

HPF SETTING (high pass filter adjustment)

Use this function when wanting to listen only to high-frequency sounds. Only frequencies higher than the high-pass filter (HPF) cutoff are output from the speakers.

1 Press M.C. to display the setting mode. 2 Press M.C. to cycle between the following:

Cut-off frequency—Slope level

3 Turn M.C. to select the desired setting.

Cut-off frequency: OFF—50HZ—63HZ—80HZ

—100HZ—125HZ—160HZ—200HZ

Slope level: –12— –24

SLA (source level adjustment)

This function prevents the volume from changing too dramatically when the source switches. ! Settings are based on the FM volume level,

which remains unchanged.

! The AM volume level can also be adjusted with

this function.

! USB, iPod, PANDORA and APP are all set to

the same setting automatically.

1 Press M.C. to display the setting mode. 2 Turn M.C. to adjust the source volume.

Adjustment range: +4 to –4

System menu

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option and press to select SYSTEM.

3 Turn M.C. to select the system menu function.

Once selected, the following system menu functions can be adjusted.

! INFO DISPLAY and BRIGHTNESS are not

available for DEH-X2600UI and DEH-X26UI.

CLOCK SET (setting the clock)

1 Press M.C. to display the setting mode. 2 Press M.C. to select the segment of the clock

display you wish to set. Hour—Minute

3 Turn M.C. to adjust the clock.

12H/24H (time notation)

1 Press M.C. to select the desired setting.

12H (12-hour clock)—24H (24-hour clock)

INFO DISPLAY (sub information)

The type of text information displayed in the sub information section can be toggled.

1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting.

SPEANA—LEVEL METER—SOURCE—CLOCK —OFF

! The signal bar indicator displays for SPEANA

or LEVEL METER when the source is set to

RADIO.

AUX (auxiliary input)

Activate this setting when using an auxiliary device connected to this unit.

1 Press M.C. to turn AUX on or off.

DIMMER (dimmer)

1 Press M.C. to turn the dimmer on or off.

! You can also change the dimmer setting by

pressing and holding

BRIGHTNESS (brightness adjustment)

You can use this setting to adjust the display brightness. The range of settings available for BRIGHTNESS will vary depending on whether DIMMER is on or off. For details, refer to DIMMER (dimmer) on page

11.

1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting.

DIMMER on: 1 to 4 DIMMER off: 1 to 5

/DIMMER.

Selecting the illumination color

Only for DEH-X3600UI and DEH-X36UI

Illumination function menu

1 Press M.C. to display the main menu.

2 Turn M.C. to display ILLUMI and press to select.

3 Turn M.C. to select the illumination function.

Once selected, the following audio functions can be adjusted.

KEY COLOR (key section color setting)

You can select desired colors for the keys of this unit.

1 Press M.C. to display the setting mode. 2 Turn M.C. to select the illumination color.

! Preset colors (ranging from WHITE to

BLUE)

! SCAN (cycle through a variety of colors au-

tomatically)

! CUSTOM (customized illumination color)

DISP COLOR (display section color setting)

You can select the desired colors for the display of this unit.

1 Press M.C. to display the setting mode. 2 Turn M.C. to select the illumination color.

! Preset colors (ranging from WHITE to

BLUE)

! SCAN (cycle through a variety of colors au-

tomatically)

! CUSTOM (customized illumination color)

BOTH COLOR (key and display color setting)

You can select the desired colors for the keys and display of this unit.

1 Press M.C. to display the setting mode. 2 Turn M.C. to select the illumination color.

! Preset colors (ranging from WHITE to

BLUE)

! SCAN (cycle through a variety of colors au-

tomatically)

ILLUMI FX (illumination effect mode)

In this mode, an illumination effect can be seen on the display at certain times such as when the ACC power is turned on/off or a CD is inserted/ ejected. 1 Press M.C. to turn ILLUMI FX on or off. ! The illumination effect will activate when the

ACC power is turned on/off regardless of whether the ILLUMI FX setting is on or off.

Note

When CUSTOM is selected, the customized color saved is selected.

Customizing the illumination color

You can create custom illumination colors for both KEY COLOR and DISP COLOR.

1 Press M.C. to display the main menu.

English

Section

Using this unit

2 Turn M.C. to display ILLUMI and press to select.

3 Turn M.C. to display KEY COLOR or DISP COLOR. Press to select.

4 Press M.C. and hold until the customizing illumination color setting appears in the display.

5 Press M.C. to select the primary color. R (red)—G (green)—B (blue)

6 Turn M.C. to adjust the brightness level. Adjustment range: 0 to 60

# You cannot select a level below 20 for all three of R (red), G (green), and B (blue) at the same time.

# You can also perform the same operation on other colors.

Note

You cannot create a custom illumination color while SCAN is selected.

About MIXTRAX

MIXTRAX technology is used to insert a variety of sound effects in between songs, allowing you to experience your music as a nonstop mix complete with visual effects.

Notes

! Depending on the file/song, sound effects

may not be available.

! Turn MIXTRAX off if the visual effects it pro-

duces have adverse effects on driving. Refer to Operations using the MIXTRAX button on page 6.

MIXTRAX menu

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option and press to select MIXTRAX.

3 Turn M.C. to select the MIXTRAX function.

Once selected, the following MIXTRAX functions can be adjusted. The function is enabled when MIXTRAX is on.

! FLASH AREA and FLASH PATTERN are not

available for DEH-X2600UI and DEH-X26UI.

! MIX PATTERNis not available for DEH-

X3600UI and DEH-X36UI.

SHORT PLAYBCK/SHORT MODE (short playback mode)

You can select the length of the playback time.

1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting.

1.0 MIN (1.0 minute)—1.5 MIN (1.5 minutes)—

2.0 MIN (2.0 minutes)—2.5 MIN (2.5 minutes) —3.0 MIN (3.0 minutes)—OFF (off)

FLASH AREA (flash area)

You can select areas for flashing colors.

1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting.

KEY/DISPLAY (key and display)—KEY (key)— OFF (off)

! When OFF is selected, the color set under IL-

LUMI is used as the display color.

FLASH PATTERN (flash pattern)

The flashing color and MIXTRAX special effects display change with changes in the sound and bass levels.

1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting.

! SOUND LEVEL 1 to SOUND LEVEL 6 – The

flash pattern changes according to the sound level. Select a desired mode.

! LOW PASS 1 to LOW PASS 6 – The flash

pattern changes according to the bass level. Select a desired mode.

! RANDOM 1 – The flash pattern changes

randomly according to the sound level mode and low pass mode.

! RANDOM 2 – The flash pattern changes

randomly according to the sound level mode.

! RANDOM 3 – The flash pattern changes

randomly according to the low pass mode.

MIX PATTERN (mix pattern)

The MIXTRAX special effects display changes with changes in the audio level.

1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting.

! SOUND LEVEL – The mix pattern changes

according to the sound level.

! LOW PASS – The mix pattern changes ac-

cording to the bass level.

! RANDOM – The mix pattern changes ran-

domly according to the sound level mode and low pass mode.

DISPLAY FX/DISP FX (display effect)

The MIXTRAX special effects display can be turned on or off.

1 Press M.C. to select the desired setting.

ON (MIXTRAX special effects display)—OFF

(normal display)

CUT IN FX (manual cut-in effect)

You can turn on or off the MIXTRAX sound effects while manually changing tracks.

1 Press M.C. to select the desired setting.

ON (on)—OFF (off)

Initial menu

1 Press and hold SRC/OFF until the unit turns off.

2 Press M.C. to display the main menu.

3 Turn M.C. to change the menu option and press to select INITIAL.

Once selected, the initial menu function below can be adjusted.

SP-P/O MODE (rear output and preout setting)

The rear speaker leads output and the RCA output of this unit can be used to connect a full-range speaker or subwoofer. Select a suitable option for your connection.

1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting.

! REAR/SUB.W – Select when there is a full-

range speaker connected to the rear speaker leads output and there is a subwoofer connected to the RCA output.

! SUB.W/SUB.W – Select when there is a

subwoofer connected directly to the rear speaker leads output without any auxiliary amp and there is a subwoofer connected to the RCA output.

! REAR/REAR – Select when there is a full-

range speaker connected to the rear speaker leads output and the RCA output. If there is a full-range speaker connected to the rear speaker leads output and the RCA output is not used, you may select either REAR/SUB.W or REAR/REAR.

Using this unit

Installation

Section

System menu

1 Press and hold SRC/OFF until the unit turns off.

2 Press M.C. to display the main menu.

3 Turn M.C. to change the menu option and press to select SYSTEM.

4 Turn M.C. to select the system menu function.

For details, refer to System menu on page 11.

Using an AUX source

1 Insert the stereo mini plug into the AUX input jack.

2 Press SRC/OFF to select AUX as the source.

Note

AUX cannot be selected unless the auxiliary setting is turned on. For more details, refer to AUX (auxiliary input) on page 11.

Switching the display

Selecting the desired text information 1 Press DISP to cycle between the following:

! Source name ! Source name and clock

If an unwanted display appears

Turn off the unwanted display using the procedures listed below.

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option and press to select SYSTEM.

3 Turn M.C. to display DEMO OFF and press to select.

4 Turn M.C. to switch to YES.

5 Press M.C. to select.

Connections

WARNING

! Use speakers over 50 W (output value) and

between 4 W to 8 W (impedance value). Do not use 1 W to 3 W speakers for this unit.

! The black cable is ground. When installing

this unit or power amp (sold separately), make sure to connect the ground wire first. Ensure that the ground wire is properly connected to metal parts of the car ’s body. The ground wire of the power amp and the one of this unit or any other device must be connected to the car separately with different screws. If the screw for the ground wire loosens or falls out, it could result in fire, generation of smoke or malfunction.

Ground wire

Other devices (Another electronic device in the car)

Important

! When installing this unit in a vehicle without

an ACC (accessory) position on the ignition switch, failure to connect the red cable to the terminal that detects operation of the ignition key may result in battery drain.

ACC position No ACC position

POWER AMP

Metal parts of car’s body

! Use this unit with a 12-volt battery and nega-

tive grounding only. Failure to do so may result in a fire or malfunction.

! To prevent a short-circuit, overheating or mal-

function, be sure to follow the directions below.

— Disconnect the negative terminal of the bat-

tery before installation.

— Secure the wiring with cable clamps or adhe-

sive tape. Wrap adhesive tape around wiring that comes into contact with metal parts to protect the wiring.

— Place all cables away from moving parts,

such as the shift lever and seat rails.

— Place all cables away from hot places, such

as near the heater outlet.

— Do not connect the yellow cable to the battery

by passing it through the hole to the engine compartment.

— Cover any disconnected cable connectors

with insulating tape.

— Do not shorten any cables. — Never cut the insulation of the power cable of

this unit in order to share the power with other devices. The current capacity of the cable is limited.

— Use a fuse of the rating prescribed. — Never wire the negative speaker cable directly

to ground.

— Never band together negative cables of multi-

ple speakers.

! When this unit is on, control signals are sent

through the blue/white cable. Connect this cable to the system remote control of an external power amp or the vehicle’s auto-antenna relay control terminal (max. 300 mA 12 V DC). If the vehicle is equipped with a glass antenna, connect it to the antenna booster power supply terminal.

! Never connect the blue/white cable to the

power terminal of an external power amp. Also, never connect it to the power terminal of the auto antenna. Doing so may result in battery drain or a malfunction.

English

4 56

Section

Installation

This unit

1 Power cord input 2 Rear output or subwoofer output 3 Front output (DEH-X3600UI and DEH-X36UI

only)

4 Antenna input 5 Fuse (10 A) 6 Wired remote input (DEH-X3600UI and DEH-

X36UI only) Hard-wired remote control adapter can be connected (sold separately).

Power cord

Perform these connections when not connecting a rear speaker lead to a subwoofer.



6 7







e f

Perform these connections when using a sub-



8 9





c d



woofer without the optional amplifier.









1 To power cord input 2 Left 3 Right 4 Front speaker 5 Rear speaker 6 White 7 White/black 8 Gray 9 Gray/black a Green b Green/black c Violet d Violet/black e Black (chassis ground)

Connect to a clean, paint-free metal location.

f Yellow

Connect to the constant 12 V supply terminal.

g Red

Connect to terminal controlled by ignition switch (12 V DC).

h Blue/white

Connect to system control terminal of the power amp or auto-antenna relay control terminal (max. 300 mA 12 V DC).

i Subwoofer (4 W)

c d

f g

k l













j When using a subwoofer of 70 W (2 W), be

sure to connect the subwoofer to the violet and violet/black leads of this unit. Do not connect anything to the green and green/ black leads.

k Not used. l Subwoofer (4 W)×2

Notes

! When using a two-speaker system, do not

connect anything to speaker leads that are not connected to a speaker.

! Change the initial menu of this unit. Refer to

SP-P/O MODE (rear output and preout setting) on page 12.

The subwoofer output of this unit is monaural.

Power amp (sold separately)

Perform these connections when using the optional amplifier. DEH-X3600UI/DEH-X36UI





DEH-X2600UI/DEH-X26UI



1 System remote control

Connect to Blue/white cable.

2 Power amp (sold separately) 3 Connect with RCA cables (sold separately)

4 To Front output 5 Front speaker 6 To Rear output or subwoofer output 7 Rear speaker or subwoofer

Installation

Important

! Check all connections and systems before

final installation.

! Do not use unauthorized parts as this may

cause malfunctions.

! Consult your dealer if installation requires

drilling of holes or other modifications to the vehicle.

! Do not install this unit where:

— it may interfere with operation of the vehicle. — it may cause injury to a passenger as a result

of a sudden stop.

! The semiconductor laser will be damaged if

it overheats. Install this unit away from hot places such as near the heater outlet.

! Optimum performance is obtained when the

unit is installed at an angle of less than 60°.

60°

5cmcm

Installation

Section

! When installing, to ensure proper heat dis-

persal when using this unit, make sure you leave ample space behind the rear panel and wrap any loose cables so they are not blocking the vents.

Leave ample

5 cm

space

5 cm

DIN front/rear mount

This unit can be properly installed using either front-mount or rear-mount installation. Use commercially available parts when installing.

DIN Front-mount

1 Insert the mounting sleeve into the dashboard.

For installation in shallow spaces, use the supplied mounting sleeve. If there is enough space, use the mounting sleeve that came with the vehicle.

2 Secure the mounting sleeve by using a screwdriver to bend the metal tabs (90°) into place.

2 Mounting sleeve

# Make sure that the unit is installed securely in place. An unstable installation may cause skipping or other malfunctions.

DIN Rear-mount

1 Determine the appropriate position where the holes on the bracket and the side of the unit match.

2 Tighten two screws on each side.

1 Screw 2 Mounting bracket 3 Dashboard or console

! Use either truss (5 mm × 8 mm) or flush sur-

face (5 mm × 9 mm) screws, depending on the bracket screw holes.

Removing the unit

1 Remove the trim ring.

! Releasing the front panel allows easier ac-

cess to the trim ring.

! When reattaching the trim ring, point the

side with the notched tab down.

2 Insert the supplied extraction keys into both sides of the unit until they click into place.

3 Pull the unit out of the dashboard.

Removing and re-attaching the front panel

You can remove the front panel to protect your unit from theft. For details, refer to Removing the front panel and Re-attaching the front panel on page 4.

Securing the front panel

The front panel can be secured with the supplied screw.

1 Screw

English

1 Dashboard

1 Trim ring 2 Notched tab

Appendix

Additional information

Troubleshooting

Symptoms are written in bold and causes in regular, non-indented text. Regular,indented text is used to indicate actions to be taken.

The display automatically returns to the ordinary display.

You did not perform any operation within about 30 seconds.

Perform operation again.

The repeat play range changes unexpectedly.

Depending on the repeat play range, the selected range may change when another folder or track is being selected or during fast forwarding/reversing.

Select the repeat play range again.

A subfolder is not played back.

Subfolders cannot be played when FLD (folder repeat) is selected.

Select another repeat play range.

NO XXXX appears when a display is changed (NO TITLE, for example).

There is no embedded text information.

Switch the display or play another track/file.

The unit is malfunctioning. There is interference.

You are using a device, such as a cellular phone, that may cause audible interference.

Move electrical devices that may be causing the interference away from the unit.

Error messages

When you contact your dealer or your nearest Pioneer Service Center, be sure to note the error message.

Symptoms are written in bold and causes in regular, non-indented text. Regular,indented text is used to indicate actions to be taken.

Common

AMP ERROR

This unit fails to operate or the speaker connection is incorrect; the protective circuit is activated.

Check the speaker connection. If the message fails to disappear even after the engine is switched off/on, contact your dealer or an authorized Pioneer Service Station for assistance.

CD player

ERROR-07, 11, 12, 17, 30

The disc is dirty.

Clean the disc.

The disc is scratched.

Replace the disc.

ERROR-07, 10, 11, 12, 15, 17, 30, A0

There is an electrical or mechanical error.

Turn the ignition switch OFF and back ON, or switch to a different source, then back to the CD player.

ERROR-15

The inserted disc is blank.

Replace the disc.

ERROR-23

Unsupported CD format.

Replace the disc.

FORMAT READ

Sometimes there is a delay between the start of playback and when you start to hear any sound.

Wait until the message disappears and you hear sound.

NO AUDIO

The inserted disc does not contain any playable files.

Replace the disc.

SKIPPED

The inserted disc contains DRM protected files.

The protected files are skipped.

PROTECT

All the files on the inserted disc are embedded with DRM.

Replace the disc.

USB storage device/iPod

FORMAT READ

Sometimes there is a delay between the start of playback and when you start to hear any sound.

Wait until the message disappears and you hear sound.

NO AUDIO

There are no songs.

Transfer the audio files to the USB storage device and connect.

The connected USB storage device has security enabled.

Follow the USB storage device instructions to disable the security.

SKIPPED

The connected USB storage device contains DRM protected files.

The protected files are skipped.

PROTECT

All the files on the connected USB storage device are embedded with DRM.

Replace the USB storage device.

N/A USB

The connected USB device is not supported by this unit.

! Connect a USB Mass Storage Class compliant device. ! Disconnect your device and replace it with a compatible USB storage device.

CHECK USB

The USB connector or USB cable has shortcircuited.

Check that the USB connector or USB cable is not caught in something or damaged.

CHECK USB

The connected USB storage device consumes more than maximum allowable current.

Disconnect the USB storage device and do not use it. Turn the ignition switch to OFF, then to ACC or ON and then connect only compliant USB storage devices.

CHECK USB

The iPod operates correctly but does not charge.

Make sure the connection cable for the iPod has not shorted out (e.g., not caught in metal objects). After checking, turn the ignition switch OFF and back ON, or disconnect the iPod and reconnect.

ERROR-19

Communication failed.

Perform one of the following operations.

–Turn the ignition switch OFF and back ON. –Disconnect the USB storage device. –Change to a different source.

Then, return to the USB source.

Additional information

Appendix

Additional information

iPod failure.

Disconnect the cable from the iPod. Once the iPod’s main menu is displayed, reconnect the iPod and reset it.

ERROR-23

USB storage device was not formatted with FAT12, FAT16 or FAT32.

USB storage device should be formatted with FAT12, FAT16 or FAT32.

ERROR-16

The iPod firmware version is old.

Update the iPod version.

iPod failure.

Disconnect the cable from the iPod. Once the iPod’s main menu is displayed, reconnect the iPod and reset it.

STOP

There are no songs in the current list.

Select a list that contains songs.

NOT FOUND

No related songs.

Transfer songs to the iPod.

Pandora

ERROR-19

Communication failed.

Disconnect the cable from the device. Once the device’s main menu is displayed, reconnect the device and reset it.

START UP APP

The Pandora application has not started running yet.

Start up the Pandora application.

INOPERABLE

The operation was disabled.

Run the same command for another track.

TRY AGAIN

Unable to save thumb rating. Unable to save BookMark. Unable to add station.

Try again later.

MAINTENANCE

Pandora system is undergoing maintenance.

Try again later.

SKIP LIMIT

Skip limit reached.

! Do not exceed the skip limit. ! Due to music licensing restrictions, Pandora

limits the total number of skips per hour.

CHECK APP

This version of the Pandora application is not supported.

Connect a device that has a compatible version of the Pandora application installed.

CHECK DEVICE

Device error message displayed in Pandora application. Unable to play music from Pandora.

Please check your connected device.

NO STATION

No station found.

Create a station in the Pandora application on your connected device.

NO ACTIVE ST

No station selected.

Select a station.

STATION FULL

A new station cannot be added.

Delete an old station to open a spot for a new one.

CAN.T DELETE

The station could not be deleted.

Run the same command for another station.

NO NETWORK

The connected device is out of area.

Connect the connected device to a network.

NO SERVICE

The connected device is out of area.

Connect the connected device to a network.

CAN.T PLAY

The operation was disabled.

Run the same command for another station.

Apps

START UP APP

The application has not started running yet.

Follow the instructions that appear on the screen.

Handling guidelines

Discs and player

Use only discs that feature either of the following two logos.

Use 12-cm discs.

Use only conventional, fully circular discs.

The following types of discs cannot be used with this unit:

! DualDiscs ! 8-cm discs: Attempts to use such discs with

an adaptor may cause the unit to malfunction.

! Oddly shaped discs

! Discs other than CDs ! Damaged discs, including discs that are

cracked, chipped or warped

! CD-R/RW discs that have not been finalized

Do not touch the recorded surface of the discs.

Store discs in their cases when not in use.

Do not attach labels, write on or apply chemicals to the surface of the discs.

To clean a CD, wipe the disc with a soft cloth outward from the center.

Condensation may temporarily impair the player ’s performance. Let it rest for about one hour to adjust to a warmer temperature. Also, wipe any damp discs off with a soft cloth.

English

Appendix

Additional information

Playback of discs may not be possible because of disc characteristics, disc format, recorded application, playback environment, storage conditions, and so on.

Road shocks may interrupt disc playback.

When using discs that can be printed on label surfaces, check the instructions and the warnings of the discs. Depending on the discs, inserting and ejecting may not be possible. Using such discs may result in damage to this equipment.

Do not attach commercially available labels or other materials to the discs. ! The discs may warp making the disc unplay-

able.

! The labels may come off during playback and

prevent ejection of the discs, which may result in damage to the equipment.

USB storage device

Connections via USB hub are not supported.

Do not connect anything other than a USB storage device.

Firmly secure the USB storage device when driving. Do not let the USB storage device fall onto the floor, where it may become jammed under the brake or accelerator pedal.

Depending on the USB storage device, the following problems may occur.

! Operations may vary. ! The storage device may not be recognized. ! Files may not be played back properly. ! The device may cause audible interference

when you are listening to the radio.

iPod

Do not leave the iPod in places with high temperatures.

Firmly secure the iPod when driving. Do not let the iPod fall onto the floor, where it may become jammed under the brake or accelerator pedal.

About iPod settings ! When an iPod is connected, this unit changes

the EQ (equalizer) setting of the iPod to off in order to optimize the acoustics. When you disconnect the iPod, the EQ returns to the original setting.

! You cannot set Repeat to off on the iPod when

using this unit. Repeat is automatically changed to All when the iPod is connected to this unit.

Incompatible text saved on the iPod will not be displayed by the unit.

Compressed audio compatibility (disc, USB)

WMA

File extension: .wma

Bit rate: 48 kbps to 320 kbps (CBR), 48 kbps to 384 kbps (VBR)

Sampling frequency: 32 kHz, 44.1 kHz, 48 kHz

Windows Mediaä Audio Professional, Lossless, Voice/DRM Stream/Stream with video: Not compatible

MP3

File extension: .mp3

Bit rate: 8 kbps to 320 kbps (CBR), VBR

Sampling frequency: 8 kHz to 48 kHz (32 kHz,

44.1 kHz, 48 kHz for emphasis)

Compatible ID3 tag version: 1.0, 1.1, 2.2, 2.3, 2.4 (ID3 tag Version 2.x is given priority over Version

1.x.)

M3u playlist: Not compatible

MP3i (MP3 interactive), mp3 PRO: Not compatible

WAV

File extension: .wav

Quantization bits: 8 and 16 (LPCM), 4 (MS ADPCM)

Sampling frequency: 16 kHz to 48 kHz (LPCM),

22.05 kHz and 44.1 kHz (MS ADPCM)

! You cannot use this function with USB MTP.

Supplemental information

Only the first 32 characters can be displayed as a file name (including the file extension) or a folder name.

This unit may not work properly depending on the application used to encode WMA files.

There may be a slight delay at the start of playback of audio files embedded with image data or audio files stored on a USB storage device that has numerous folder hierarchies.

Disc

Playable folder hierarchy: up to eight tiers (A practical hierarchy is less than two tiers.)

Playable folders: up to 99

Playable files: up to 999

File system: ISO 9660 Level 1 and 2, Romeo, Joliet

Multi-session playback: Compatible

Packet write data transfer: Not compatible

Regardless of the length of blank sections between the songs from the original recording, compressed audio discs play with a short pause between songs.

USB storage device

Playable folder hierarchy: up to eight tiers (A practical hierarchy is less than two tiers.)

Playable folders: up to 500

Playable files: up to 15 000

Playback of copyright-protected files: Not compatible

Partitioned USB storage device: Only the first partition can be played.

There may be a slight delay when starting playback of audio files on a USB storage device with numerous folder hierarchies.

CAUTION

! Pioneer cannot guarantee compatibility with

all USB mass storage devices and assumes no responsibility for any loss of data on media players, smart phones, or other devices while using this product.

! Do not leave discs or a USB storage device

in any place that is subject to high temperatures.

iPod compatibility

This unit supports only the following iPod models. Supported iPod software versions are shown below. Older versions may not be supported.

Additional information

Appendix

Additional information

Made for

! iPod touch (5th generation) ! iPod touch (4th generation) ! iPod touch (3rd generation) ! iPod touch (2nd generation) ! iPod touch (1st generation) ! iPod classic ! iPod with video ! iPod nano (7th generation) ! iPod nano (6th generation) ! iPod nano (5th generation) ! iPod nano (4th generation) ! iPod nano (3rd generation) ! iPod nano (2nd generation) ! iPod nano (1st generation) ! iPhone 5 ! iPhone 4S ! iPhone 4 ! iPhone 3GS ! iPhone 3G ! iPhone

Depending on the generation or version of the iPod, some functions may not be available.

Operations may vary depending on the software version of iPod.

Users of iPod with the Lightning Connector should use the Lightning to USB Cable (supplied with iPod).

Users of iPod with the Dock Connector should use CD-IU51. For details, consult your dealer.

About the file/format compatibility, refer to the iPod manuals.

Audiobook, Podcast: Compatible

CAUTION

Pioneer accepts no responsibility for data lost on the iPod, even if that data is lost while this unit is used.

Sequence of audio files

The user cannot assign folder numbers and specify playback sequences with this unit.

Example of a hierarchy

 

 

Level 1 Level 2 Level 3 Level 4

Disc

Folder selection sequence or other operation may differ depending on the encoding or writing software.

USB storage device

Playback sequence is the same as recorded sequence in the USB storage device. To specify the playback sequence, the following method is recommended. 1 Create a file name that includes numbers

that specify the playback sequence (e.g., 001xxx.mp3 and 099yyy.mp3).

2 Put those files into a folder. 3 Save the folder containing files on the USB

storage device. However,depending on the system environment, you may not be able to specify the playback sequence. For USB portable audio players, the sequence is different and depends on the player.

 

: Folder

: Compressed audio file 01 to 05: Folder number 1 to 6: Playback sequence

iTunes

Apple and iTunes are trademarks of Apple Inc., registered in the U.S. and other countries.

MP3

Supply of this product only conveys a license for private, non-commercial use and does not convey a license nor imply any right to use this product in any commercial (i.e. revenue-generating) real time broadcasting (terrestrial, satellite, cable and/or any other media), broadcasting/ streaming via internet, intranets and/or other networks or in other electronic content distribution systems, such as pay-audio or audio-on-demand applications. An independent license for such use is required. For details, please visit http://www.mp3licensing.com.

WMA

Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. This product includes technology owned by Microsoft Corporation and cannot be used or distributed without a license from Microsoft Licensing, Inc.

iPod & iPhone

iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. Lightning is a trademark of Apple Inc.

“Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulator y standards. Please note that the use of this accessory with iPod or iPhone may affect wireless performance.

Androidä

Android is a trademark of Google Inc.

Pandora®internet radio

PANDORA, the PANDORA logo, and the Pandora trade dress are trademarks or registered trademarks of Pandora Media, Inc. Used with permission.

MIXTRAX

MIXTRAX is a trademark of the PIONEER CORPORATION.

English

Appendix

Additional information

Specifications

General

Power source ................... 14.4 V DC (10.8 V to 15.1 V al-

Grounding system ............ Negative type

Maximum current consumption

................................... 10.0 A

Dimensions (W × H × D): DIN

Chassis ............................ 178 mm × 50 mm × 165 mm

Nose ................................ 188mm × 58mm × 15 mm

Chassis ............................ 178 mm × 50 mm × 165 mm

Nose ................................ 170mm × 46mm × 15 mm

(DEH-X3600UI/DEH-X36UI)

Nose ................................ 170mm × 46 mm × 16 mm

(DEH-X2600UI/DEH-X26UI)

Weight ............................. 1 kg (2.2 lbs)

Audio

Maximum power output ... 50 W × 4

Continuous power output

................................... 22 W × 4 (50 Hz to 15000 Hz,

Load impedance .............. 4 W (4 W to 8 W allowable)

Preout maximum output level

................................... 2.0 V

Loudness contour ............ +10dB (100 Hz), +6.5 dB

Equalizer (5-Band Graphic Equalizer):

Frequency ........................ 80 Hz/250 Hz/800 Hz/2.5kHz/

Equalization range ........... ±12 dB (2 dB step)

Subwoofer (mono):

Frequency ........................ 50 Hz/63 Hz/80 Hz/100 Hz/

Slope ............................... –12 dB/oct, –24 dB/oct

Gain ................................ +6dB to –24 dB

Phase .............................. Normal/Reverse

CD player

System ............................ Compact disc audio system

Usable discs .................... Compact disc

lowable)

(7 in. × 2 in. × 6-1/2 in.)

(7-3/8 in.× 2-1/4 in.× 5/8 in.)

(7 in.× 2 in.× 6-1/2 in.)

(6-3/4 in.× 1-3/4 in.× 5/8 in.)

(6-3/4 in. × 1-3/4 in. × 5/8 in.)

70 W × 1/2 W (for subwoofer)

5 % THD, 4 W load, both channels driven)

(10 kHz) (volume: –30 dB)

8 kHz

125 Hz/160 Hz/200 Hz

Signal-to-noise ratio ......... 94 dB (1 kHz) (IHF-A network)

Number of channels ........ 2 (stereo)

MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3

WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch

WAV signal format ........... Linear PCM & MS ADPCM

USB

USB standard specification

................................... USB 2.0 full speed

Maximum current supply

................................... 1 A

USB Class ....................... MSC (Mass Storage Class)

File system ....................... FAT12, FAT16, FAT32

MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3

WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch

WAV signal format ........... Linear PCM & MS ADPCM

FM tuner

Frequency range .............. 87.9 MHz to 107.9 MHz

Usable sensitivity ............. 9 dBf (0.8 µV/75 W, mono, S/N:

Signal-to-noise ratio ......... 72 dB (IHF-A network)

AM tuner

Frequency range .............. 530 kHz to 1 710 kHz

Usable sensitivity ............. 25 µV (S/N: 20 dB)

Signal-to-noise ratio ......... 62 dB (IHF-A network)

audio) (Windows Media Player)

(Non-compressed)

audio) (Windows Media Player)

(Non-compressed)

30 dB)

CEA2006 Specifications

Power output ................... 14 W RMS × 4 Channels (4 W

S/N ratio .......................... 91 dBA (reference: 1 W into

and ≦ 1 % THD+N)

4 W)

Note

Specifications and the design are subject to modifications without notice.

+ 44 hidden pages