Pinnacle MAC-12F, MAC-20FO-DDF, MAC-20S-DDF, MAC-24-DDF, MAC-24POSC User's Manual And Operating Instructions

...

Download

User’s Manual and Operating Instructions

CAUTION

WARNING

Model Numbers:

MAC-12F, MAC-20F-DDF, MAC-20FO-DDF, MAC-20S-DDF, MAC-24-DDF, MAC-24P, MAC-24POSC,

MAC-24W, MAC-24WOSC, MAC-30W, MAC-30WOSC, MAC-30-DDF, MAC-30P-DDF, MAC-30POSC

MAC-36DCT-BDF, PT-20F-DDF, PT-20FO-DDF, PT-20S-DDF, PT-24-DDF, PT-30-DDF, PT-30P-DDF

CONSUMER: READ AND SAVE THESE INSTRUCTIONS

IMPORTANT: Read and understand all of the instructions in this manual before assembling, starting, or servicing the fan. Improper use of this fan can cause serious injury. Keep this manual for future reference.

For General Ventilating Use Only. Do Not Use To Exhaust Hazardous Or Explosive Materials And Vapors. Never use the fan in spaces which contain products such as gasoline, solvents, paint thinners, dust particles, volatile or airborne combustibles, or any

unknown chemicals.

Safety Information

THIS IS A FAN - NOT A TOY! TO REDUCE THE RISK OF PERSONAL INJURY AND ELECTRIC SHOCK, FANS SHOULD NOT BE PLAYED WITH OR PLACED WHERE SMALL CHILDREN CAN REACH IT.

To guard against electric shock while operating, do not allow fan to come in contact with other grounded objects such as pipes, radiators, etc.

Risk of fire, electric shock, or personal injury when performing service or maintenance. Unplug or disconnect the fan from the power supply before servicing.

CAUTION Automatically Operated Device - To Reduce The Risk Of Injury Disconnect From Power Source Before Servicing

To Reduce The Risk Of Fire Or Electric Shock, Do Not Use This Fan With Any Solid- State Speed Control Device.

To Reduce The Risk Of Electric Shock And Injury To Persons, Do Not Use In a Window.

To Reduce The Risk Of Electric Shock, Do Not Expose To Water Or Rain. This unit is designed for indoor use only.

Do not operate any fan with a damaged cord or plug. Discard fan or return to an authorized

service facility for examination and/or repair. Do not run cord under carpeting. Do not cover cord with throw rugs , runner, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic areas and where it will not be tripped over.

1 Industrial Blvd #101, Sauk Rapids, MN 56379 USA • Toll Free (800) 779-3267

Fax: 320-251-2922 • Web: www.pinnacleclimate.com • Email: info@pinnacleclimate.com

86&

(

NEVER LEAVE A FAN UNATTENDED WHILE OPERATING OR WHILE CONNECTED TO A

WARNING

POWER SOURCE

Installation work and electrical wiring must be done by qualified

person(s) in accordance with all applicable codes and regulations.

When servicing or replacing a component requires the removal or

disconnection of a safety device, the safety device is to be

reinstalled or remounted as previously installed before operating

this fan.

Use this fan only in the manner intended by the manufacturer. If

you have any questions, contact Customer Service at 800-641-

6996.

- Before operating always check fan for loose or damaged parts. Inspect power cord for any damage. Never use fan if any parts are damaged or missing. Never use fan without safety guards attached.

- Operate only on 120 volt 60 Hz (cycle) current with a minimum of a 15 amp circuit.

12"/20" Floor Fan

12F

20" Omni Floor Fan

20FO-DDF

20F-DDF

86&

(

36" Cradle Fan

36DCT-BDF

86&

(

30-DDF

86&

(

30" Floor Fan

86&

(

- When used with an extension cord, use only cord of proper size (Amp rating), UL listed, and with receptacle to accept three prong grounded plug furnished on the fan’s power cord. Always keep power cord and extension cords away from heat, oil, and sharp edges. Inspect cords periodically and replace if damaged.

24" Barrel Fan

24-DDF

86&

(

20"/30" Wall Fan

24W 24WOSC

30W 30WOSC

86&

(

20" Shop Fan

20S-DDF

86&

(

20"/30" Pedestal Fan

24P 24POSC

30P-DDF 30POSC

86&

(

NEVER LEAVE A FAN UNATTENDED WHILE OPERATING OR WHILE CONNECTED TO A

WARNING

POWER SOURCE

24" and 30" Wall Fans: 24W / 24WOSC / 30W / 30WOSC

Wall Mount Installation

1. Attach fan to wall or ceiling using Upper Bracket.

2. Be sure Upper Bracket is attached to a suitable beam when hanging.

Tools Needed:

- 10 mm Adjustable Wrench.

mounted to a minimum of a 2x4" stud, and that it is able to support 50 pounds continuously.

The installer MUST be certain that the support bracket is

NEVER LEAVE A FAN UNATTENDED WHILE OPERATING OR WHILE CONNECTED TO A

POWER SOURCE

12" & 20" FLOOR FANS / 24" BARREL FANS: 12F / 20F-DDF / 20FO-DDF / 24-DDF

Installation and Assembly

1. Place the fan on level ground in a safe,

desired position then connect to an approved power source.

24" BARREL FAN

Exploded View (24-DDF Only)

NOTE: This model CAN NOT be wall mounted.

30" FLOOR FAN / 36" CRADLE FAN: 30-DDF / 36-DCT-BDF

Installation and Assembly

1. Slide wheel axle through wheel support frame.

2. Slide one (1) wheel onto either side of axle.

This 30" Floor Fan (30-DDF-B) is approved for use with California’s BAR97 Emissions Inspection System and meets all BAR-97(EIS) required

specications and standards

3. Secure wheel with one (1) cotter pin.

4. Place the fan on level ground in a safe, desired position and connect to an approved power source.

Exploded View (30-DDF Only)

NEVER LEAVE A FAN UNATTENDED WHILE OPERATING OR WHILE CONNECTED TO A

CAUTION

POWER SOURCE

24" & 30" PEDESTAL FANS: 24P / 24POSC / 30POSC / 30P-DDF

Installation and Assembly

Tools Needed: Pliers Phillips head screwdriver Flat head screwdriver 10 mm / adjustable wrench

Parts Included In Box: (1) Base (1) Front Guard (1) Rear Guard (1) Motor Assembly (1) Fan Blade Assembly (1) Locking Collar

(1) Upper Support Pole (1) Lower Support Pole

1. Place the base on level ground

2. Mount the support pole to the base. Make

sure the holes line up.

3. Secure tightly with 5 flange screws using the

wrench.

4. Put down the base cover.

5. Loosen the locking collar screw using the

Allen wrench (hex wrench). Extract the upper support pole slowly to adjust the height of the fan.

6. Mount the motor assembly to the connector

on the upper support pole. Make sure the holes line up

7. Secure motor assembly with Bolt (M12*40)

and Nut (M12). Tighten the bolt firmly using the wrench.

8. Slide the rear guard on to motor assembly

and secure it with 4 flange screws. Tighten the screws firmly using the wrench.

Nut

Figure 1: Attaching Motor to Motor Support Assembly

Motor Assembly

Pivot Bolt

Upper Support Pole

Rear Guard

Motor

9. Loosen the screw on the back of the fan

blade assembly using the Allen wrench (Hex Wrench). Slide the fan blade assembly onto the motor shaft.

10. Attach the front guard to the back guard and

secure with the fasteners on the front guard.

NOTE: This model CAN NOT be wall mounted

Do NOT slide fan blade screw beyond the groove

on the shaft! This will cause the fan blade to not spin properly and can cause damage to your fan! Be sure that fan shaft is flush with front of fan blade assembly.

Figure 2: Attaching Rear Guard to Motor

NEVER LEAVE A FAN UNATTENDED WHILE OPERATING OR WHILE CONNECTED TO A

WARNING

POWER SOURCE

20" SHOP FAN: 20S-DDF

Installation and Assembly

1. Remove Knob Screw and Wing Nut from top of Post.

2. Slide Connector Bracket onto top of post.

3. Line up holes on the Post and Connector Bracket.

4. Re-insert the Knob Screw through the Post and Connector Bracket and tighten firmly with the Wing Nut.

5. Place the fan on level ground in a safe, desired position then connect to an approved power source.

6. Set desired tripod stand height following “Tripod Operation Instructions” below.

Tripod Operation Instructions

TRIPOD LEG OPERATION

1. Fold legs out and slide support bracket to center of leg.

2. To adjust leg height; rotate locking ring clockwise to loosen.

NOTE: Keep a firm grip on the tripod while leg is

unlocked! The leg will collapse into itself unless held tightly.

OPTIONAL CEILING MOUNT

1. Attach Ceiling Mounting Kit to 2x4" stud that is able to support 50 lbs continuously using M6x40 mm screw. (See Figure 3)

The installer MUST be certain that the support bracket is

mounted to a minimum of a 2x4" stud, and that it is able to support 50 pounds continuously.

2. Be certain that the Safety Pin lines up with the groove on the Frame. (See Figure 4)

NOTE: Be certain to make all three legs the same

height. Setting legs to different heights will make the fan unbalanced and COULD FALL OVER.

3. Slide leg extension to desired height.

4. Rotate locking ring counter-clockwise and tighten firmly. Be sure the leg is secure before moving to next leg.

5. Repeat steps 2-4 for remaining legs.

TRIPOD CENTER POST OPERATION

1. To change the post height; rotate locking ring counter-clockwise to unlock post.

NOTE: Be certain to keep a firm grip on post while

unlocked! The fan will slide down to its lowest point if it is not held and slowly moved to desired position.

2. Raise or lower post to desired position.

3. Rotate locking ring clockwise to lock post and tighten firmly.

DO NOT MOVE OR ADJUST

FAN WHILE IN OPERATION. THIS CAN CAUSE DAMAGE TO FAN AND INJURY TO THE OPERATOR.

3. Slide Connector Bracket onto Ceiling Mounting Post. (See Figure 5)

4. Rotate the entire fan so the safety pin locks into place and the holes on the Mounting Post line up with the holes on the Connector Bracket. (See Figure 6)

5. Insert the Base Knob through the Mounting Post and Connector Bracket and tighten firmly with the Wing Nut (See Figure 6)

Figure 3: Optional Ceiling Mount

Figure 4: Optional Ceiling Mount

Figure 5: Optional Ceiling Mount

Figure 6: Optional Ceiling Mount

NEVER LEAVE A FAN UNATTENDED WHILE OPERATING OR WHILE CONNECTED TO A

POWER SOURCE

24" & 30" PEDESTAL FANS

Exploded View

20" SHOP FAN

Exploded View

1 YEAR LIMITED WARRANTY

PINNACLE CLIMATE TECHNOLOGIES, INC. WARRANTS THIS

PRODUCT TO THE ORIGINAL RETAIL PURCHASER ONLY, TO BE FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIP FOR A PERIOD OF ONE (1) YEAR FROM THE DATE OF INITIAL PURCHASE. THIS PRODUCT MUST BE PROPERLY INSTALLED, MAINTAINED AND OPERATED IN ACCORDANCE WITH THE INSTRUCTIONS PROVIDED.

PINNACLE CLIMATE TECHNOLOGIES, INC. REQUIRES REASONABLE PROOF OF YOUR DATE OF PURCHASE FROM AN AUTHORIZED RETAILER OR DISTRIBUTOR. THEREFORE, YOU SHOULD KEEP YOUR SALES SLIP, INVOICE, OR CANCELLED CHECK FROM THE ORIGINAL PURCHASE. THIS LIMITED WARRANTY SHALL BE LIMITED TO THE REPAIR OR REPLACEMENT OF PARTS, WHICH PROVE DEFECTIVE UNDER NORMAL USE AND SERVICE WITHIN THE WARRANTY PERIOD, AND WHICH PINNACLE CLIMATE TECHNOLOGIES, INC. SHALL DETERMINE AT ITS REASONABLE DISCRETION.

THIS WARRANTY DOES NOT APPLY TO PRODUCTS PURCHASED FOR RENTAL USE.

THIS LIMITED WARRANTY DOES NOT COVER REPLACEMENT OF BELTS OR TIGHTENING OF BELTS, OR ANY FAILURES OR OPERATING DIFFICULTIES DUE TO NORMAL WEAR AND TEAR, ACCIDENT, ABUSE, MISUSE, ALTERATION, MISAPPLICATION, IMPROPER INSTALLATION OR IMPROPER MAINTENANCE AND SERVICE BY YOU OR ANY THIRD PARTY. FAILURE TO PERFORM NORMAL AND ROUTINE MAINTENANCE ON THE FAN, SHIPPING DAMAGE, DAMAGE RELATED TO INSECTS, BIRDS, OR ANIMALS OF ANY KIND, AND DAMAGE DUE TO WEATHER CONDITIONS ARE ALSO NOT COVERED. IN ADDITION, THE LIMITED WARRANTY DOES NOT COVER DAMAGE TO THE FINISH, SUCH AS SCRATCHES, DENTS, DISCOLORATION, RUST OR OTHER WEATHER DAMAGE, AFTER PURCHASE.

ALL TRANSPORTATION COSTS FOR THE RETURN OF THE DAMAGED PRODUCT OR PARTS WILL BE THE RESPONSIBILITY OF THE PURCHASER. UPON RECEIPT OF DAMAGED ITEM, PINNACLE CLIMATE TECHNOLOGIES, INC. WILL EXAMINE THE ITEM AND DETERMINE IF DEFECTIVE.

PINNACLE CLIMATE TECHNOLOGIES, INC. WILL REPAIR OR REPLACE AND RETURN THE ITEM, FREIGHT PRE-PAID. IF PINNACLE CLIMATE TECHNOLOGIES, INC. FINDS THE ITEM TO BE IN NORMAL OPERATING CONDITION, OR NOT DEFECTIVE, THE ITEM WILL BE RETURNED FREIGHT COLLECT.

THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. PINNACLE CLIMATE TECHNOLOGIES, INC. DISCLAIMS ALL WARRANTIES FOR PRODUCTS THAT ARE PURCHASED FROM SELLERS OTHER THAN AUTHORIZED RETAILERS OR DISTRIBUTORS.

AFTER THE PERIOD OF THE ONE (1) YEAR LIMITED WARRANTY EXPIRES, PINNACLE CLIMATE TECHNOLOGIES, INC. DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR APPLICATION. FURTHER, PINNACLE CLIMATE TECHNOLOGIES, INC. SHALL HAVE NO LIABILITY WHATSOEVER TO PURCHASER OR ANY THIRD PARTY FOR ANY SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. PINNACLE CLIMATE TECHNOLOGIES, INC. ASSUMES NO RESPONSIBILITY FOR ANY DEFECTS CAUSED BY THIRD PARTIES. THIS LIMITED WARRANTY GIVES THE PURCHASER SPECIFIC LEGAL RIGHTS; A PURCHASER MAY HAVE OTHER RIGHTS DEPENDING UPON WHERE HE OR SHE LIVES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON HOW LONG A WARRANTY LASTS, SO THE ABOVE EXCLUSION AND LIMITATIONS MAY NOT APPLY TO YOU.

PINNACLE CLIMATE TECHNOLOGIES, INC. DOES NOT AUTHORIZE ANY PERSON OR COMPANY TO ASSUME FOR IT ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION, USE, REMOVAL, RETURN, OR REPLACEMENT OF ITS EQUIPMENT, AND NO SUCH REPRESENTATIONS ARE BINDING ON PINNACLE CLIMATE

TECHNOLOGIES, INC.

ALWAYS BE SURE TO SPECIFY MODEL NUMBER AND SERIAL NUMBER WHEN MAKING ANY CLAIM WITH PINNACLE CLIMATE TECHNOLOGIES, INC. FOR YOUR CONVENIENCE USE THE SPACE PROVIDED BELOW TO LIST THIS INFORMATION:

Model #: ____________________ Serial #: ______________________

Date of Purchase: _________________

Pinnacle MAC-12F, MAC-20FO-DDF, MAC-20S-DDF, MAC-24-DDF, MAC-24POSC User's Manual And Operating Instructions

Specifications and Main Features

Frequently Asked Questions

User Manual