Philips XL6651C/22, XL6652C/38, XL6651C/38, XL6601C/38, XL6651C/FT Quick Start Manual
...
Register your product and get support at XL660
www.philips.com/welcome XL665
Call from the phonebook
1. Press e in idle mode.
2. Select a phonebook record you want to call.
3. Press
: key to dial out the call.
ECO mode
The ECO mode reduces the transmission power of the handset and base station.
1. Press
MENU.
2. Select
ADV. SETTING > ECO, then press OK to confirm.
3. Select the new setting, then press
The setting is saved.
is displayed instead of in standby mode.
Note
When the ECO mode is activated, the connection range between the handset and the
base station can be reduced.
Listen to messages recorded on the answering machine (for XL665 only)
Press o on the base station to turn on the answering machine (the message counter is
turned on).
Press
o again to turn off the answering machine (the message counter is turned off).
p on the base station to play phone messages (the first recorded message will be
Press
played first).
Press
] to skip the current message and play the next message.
[ once to replay current message.
Press
[ twice to go back to the previous message.
Press
, to adjust speaker volume during message playback.
Press
f to delete the current message.
Press
Refer to your new phone’s User Manual for details about the answering machine function.
OK to confirm.
Troubleshooting
For more information, please refer to the User Manual that came with your
phone.
Problem Solution
• There’s no dialling tone! • Check the connections
• Caller cannot hear me
clearly!
SEARCHING... is
•
displayed on handset and
icon is blinking!
• Caller number is not
displayed!
• Charge the batteries
• Use the line cable provided
• Move closer to the base station
• Move the base station at least one metre away
from any electrical appliances
• Move closer to the base station
• Reset your unit and restart the handset registration
• Check your subscription with your network
operator
Welcome to Philips!
Register your product and get support at
www.philips.com/welcome
Need help?
User Manual
Refer to the User Manual that came with your new phone.
Online help
www.philips.com/support
©2008 Koninklijke Philips Electronics N.V.
All rights reserved.
Reproduction in whole or in part is prohibited without
the written consent of the copyright owner.
Document number: 69239AZ(0) (GB) Printed in Vietnam
UFZZ69239AZ(0)
Quick start guide
Connect
1
Install
2
Enjoy
3
What’s in the box
Base station for XL660
OR
Handset
Battery door
Connect
1
Connect the base station
1.
Place the base station in a central location near the telephone line socket and electricity socket.
Enjoy
3
Make a call
Dial the number (maximum 24 digits) and press : key.
OR
Press
: key to take the line and dial the number (maximum 24 digits).
Answer a call
When the phone rings, press : key.
End a call
To end a conversation, press : key.
XL665
NiMH batteries
*You may find in the box the line adaptor delivered separately from the line cable. In this
case, you have to connect the line adaptor to the line cord first before plugging the line
cord to the line socket.
In multihandset packs, you will find one or more additional handsets, chargers with power
supply units and additional rechargeable batteries.
WARNING Always use the cables and batteries that came with your phone.
Power supply2 AAA rechargeable
GuaranteeUser manual
Line cord*
Quick Start Guide
2. Connect the line cord and the power cable to their corresponding connectors at the
back of the base station.
3. Connect the other end of the line cord and power cable to their respective sockets.
Install
2
Insert rechargeable batteries and charge
Remove the insulation foil Charge handset for 24 hours
Configure your phone (if necessary)
After installing the batteries and charging your phone for a few minutes, your phone
displays a Welcome message in various languages:
OK. Press C or < to select your country.
1. Press
2. Press
OK to confirm your selection.
3. Enter the current date and time (hh:mm MM/DD/YY) and press
Your phone is now ready for use.
OK to confirm.
Adjust earpiece volume
During a call, press C or < to select from LEVEL 1 to LEVEL 5,
Set the ring melody
1. Press MENU.
2. Select
RING TONES > CHOICE. Press OK.
3. Press
C or < to your desired melody. Press OK.
The melody is set.
Store a contact in the phonebook
1. Press e.
2. Press
OPTION. Select ADD. Press OK.
3. Enter the name of the contact (maximum 14 characters). Press
4. Enter the number (maximum 24 digits). Press
Your new record is saved.
Access the phonebook
1. Press e in idle mode and press C or < to browse the phonebook.
SAVE.
OK.
Loading...