Philips TEA1102TS-N3, TEA1102T-N3, TEA1102T-N2, TEA1102T-N1, TEA1102-N3 Datasheet

...
DATA SH EET
Preliminary specification Supersedes data of 1997 Oct 09 File under Integrated Circuits, IC03
1999 Jan 27
INTEGRATED CIRCUITS
TEA1102; TEA1102T; TEA1102TS
Fast charge ICs for NiCd, NiMH, SLA and LiIon
1999 Jan 27 2
Philips Semiconductors Preliminary specification
Fast charge ICs for NiCd, NiMH, SLA and LiIon
TEA1102; TEA1102T;
TEA1102TS
FEATURES
Safe and fast charging of Nickel Cadmium (NiCd), Nickel Metal Hydride (NiMH), Lithium Ion (LiIon), and Sealed Lead Acid (SLA) batteries
Three charge states for NiCd or NiMH; fast, top-off and trickle or voltage regulation (optional)
Two charge states for LiIon or SLA; current and voltage limited
Adjustable fast charge current [0.5CA to 5CA nominal (CA = Capacity Amperes)]
DC top-off and pulsating trickle charge current (NiCd and NiMH)
Temperature dependent T/t battery full detection
Automatic switch-over to accurate peak voltage
detection (
1
⁄4%) if no NTC is applied
Possibility to use both ∆T/∆t and peak voltage detection
as main fast charge termination
Support of inhibit during all charging states
Manual refresh with regulated adjustable discharge
current (NiCd and NiMH)
Voltage regulation in the event of no battery
Support of battery voltage based charge indication and
buzzer signalling at battery insertion, end of refresh and at full detection
Single, dual and separate LED outputs for indication of charge status state
Minimum and maximum temperature protection
Time-out protection
Short-circuit battery voltage protection
Can be applied with few low-cost external components.
GENERAL DESCRIPTION
The TEA1102x are fast charge ICs which are able fast charge NiCd and NiMH, SLA and Lilon batteries.
The main fast charge termination for NiCd and NiMH batteries are T/t and peak voltage detection, both of which are well proven techniques. The TEA1102x automatically switches over from T/t to peak voltage detection if the thermistor fails or is not present. The T/t detection sensitivity is temperature dependent, thus avoiding false charge termination. Three charge states can be distinguished; fast, top-off and trickle.
Charging Lilon and SLA batteries is completely different. When the batteries reach their maximum voltage (adjustable), the TEA1102x switches over from current regulation to voltage regulation. After a defined time period, which is dependent on battery capacity and charge current, charge is terminated. Due to small self discharge rates of Lilon and SLA batteries, trickle charge can be omitted.
Several LEDs, as well as a buzzer, can be connected to the TEA1102x for indicating battery insertion, charge states, battery full condition and protection mode.
The TEA1102x are contained in a 20-pin package and are manufactured in a BiCMOS process, essentially for integrating the complex mix of requirements in a single chip solution. Only a few external low cost components are required in order to build a state of the art charger.
ORDERING INFORMATION
TYPE
NUMBER
PACKAGE
NAME DESCRIPTION VERSION
TEA1102 DIP20 plastic dual in-line package; 20 leads (300 mil) SOT 146-1 TEA1102T SO20 plastic small outline package; 20 leads; body width 7.5 mm SOT163-1 TEA1102TS SSOP20 plastic shrink small outline package; 20 leads; body width 5.3 mm SOT339-1
1999 Jan 27 3
Philips Semiconductors Preliminary specification
Fast charge ICs for NiCd, NiMH, SLA and LiIon
TEA1102; TEA1102T;
TEA1102TS
QUICK REFERENCE DATA
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
V
P
supply voltage 5.5 11.5 V
I
P
supply current outputs off 4 mA
V
NTC/VNTC
temperature rate dependent (T/t) detection level
V
NTC
=2V;
Tj= 0 to 50 °C
−−0.25 %
V
bat/Vbat
voltage peak detection level with respect to top value
V
bat
=2V;
Tj= 0 to 50 °C
−−0.25 %
I
Vbat
input current battery monitor V
bat
= 0.3 to 1.9 V 1 nA
V
bat(l)
voltage at pin 19 for detecting low battery voltage
0.30 V
I
IB
battery charge current fast charge 10 100 µA
top-off mode 3 −µA
I
IB(max)
maximum battery charge current voltage regulation full
NiCd and NiMH battery
10 −µA
I
IB(Lmax)
maximum load current no battery 40 −µA
f
osc
oscillator frequency 10 200 kHz
V
reg
regulating voltage LiIon 1.37 V
SLA 1.63 V NiCd and NiMH
(pin V
stb
open-circuit)
1.325 or V
stb
V
open battery 1.9 V
1999 Jan 27 4
Philips Semiconductors Preliminary specification
Fast charge ICs for NiCd, NiMH, SLA and
LiIon
TEA1102; TEA1102T;
TEA1102TS
This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in
_white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in
white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ...
BLOCK DIAGRAM
handbook, full pagewidth
PROTECTION
NTC present
T
cut-off
battery low
end refresh
no­battery
T
min
T
max
0.3 V
1 V
1.9 V
3.3 V
2.8 V
1 V
0.75 V
4.25 V
156 k
36 k
12 k
DA/AD
CONVERTER
1.325 V/V
stb
NiCd
NIMH
1.37 V Llion
1.63 V SLA
1.9 V no­battery
V
bat
V
reg
CHARGE CONTROL
AND
OUTPUT DRIVERS
fast
charge
1.25/R
ref
top off
3 µA
standby
current
10 µA
load
current
40 µA
4.25 V
RSQ
LS
OSC
PWM
SET
A1
A4
100 mV
refresh
CONTROL LOGIC
SUPPLY
BLOCK
TIMER
AND
CHARGE
STATUS
INDICATION
V
bat
MTV
NTC
9
8
V
bat
V
stbRref
OSC
19 1 20 14
15
17
18
10
2
4
5
6 7
PWM
LS
AO
RFSH
IB
PSD
LED
POD PTD
12 13 16 113
VPVslVSGND FCT
TEA1102
A2
A3
4×
MGC818
Fig.1 Block diagram.
1999 Jan 27 5
Philips Semiconductors Preliminary specification
Fast charge ICs for NiCd, NiMH, SLA and LiIon
TEA1102; TEA1102T;
TEA1102TS
PINNING
SYMBOL PIN DESCRIPTION
V
stb
1 standby regulation voltage input
(NiCd and NiMH) IB 2 charge current setting GND 3 ground PSD 4 program pin sample divider LED 5 LED output POD 6 program pin oscillator divider PTD 7 program pin time-out divider NTC 8 temperature sensing input MTV 9 maximum temperature voltage RFSH 10 refresh input/output FCT 11 fast charge termination and
battery chemistry identification V
P
12 positive supply voltage
V
sl
13 switched reference voltage output OSC 14 oscillator input PWM 15 pulse width modulator output V
S
16 stabilized reference voltage LS 17 loop stability pin AO 18 analog output V
bat
19 single-cell battery voltage input R
ref
20 reference resistor pin
Fig.2 Pin configuration.
handbook, halfpage
TEA1102
MBH067
1 2 3 4 5 6 7 8 9
10
20 19 18 17 16 15 14 13 12 11
V
stb
R
ref
V
bat
V
sl
V
P
V
S
AO LS
PWM OSC
FCT
IB
GND
PSD LED
POD
PTD NTC
MTV
RFSH
1999 Jan 27 6
Philips Semiconductors Preliminary specification
Fast charge ICs for NiCd, NiMH, SLA and LiIon
TEA1102; TEA1102T;
TEA1102TS
INTRODUCTION
All battery types are initially fast charged with an adjustable high current. Fast charge termination depends upon the battery type. With NiCd and NiMH batteries the main fast charge termination will be theT/t (temperature detection) and/or peak voltage detection and with SLA and LiIon batteries when the battery voltage reaches
2.45 or 4.1 V respectively. The fast charge period is followed by a top-off period for
NiCd and NiMH batteries and by a fill-up period for SLA and LiIon batteries. During the top-off period the NiCd and NiMH batteries are charged to maximum capacity by reduced adjustable charge current.
During the fill-up period the SLA and LiIon batteries are charged to maximum capacity by a constant voltage and a gradually decreasing current. The fill-up and top-off period ends after time-out or one hour respectively.
After the fill-up or top-off period, the TEA1102x switches over to the standby mode. For NiCd and NiMH batteries either the voltage regulation or trickle charge mode can be selected. The voltage regulation mode is selected when the battery includes a fixed load. Trickle charge prevents a discharge of the battery over a long period of time. For SLA and LiIon batteries the charge current is disabled during standby. The fast charge mode is entered again when the battery voltage reaches 1.5 V (SLA) or 3 V (LiIon).
Charging principles
C
HARGING NiCd/NiMH BATTERIES
Fast charging of the battery begins when the power supply voltage is applied and at battery insertion.
During fast charge of NiCd and NiMH batteries, the battery temperature and voltage are monitored. Outside the initialized temperature and voltage window, the system switches over to the top-off charge current.
The TEA1102x supports detection of fully charged NiCd and NiMH batteries by either of the following criteria:
•∆T/∆t
Voltage peak detection.
If the system is programmed withT/t and V
peak
or,T/t
or V
peak
as the main fast charge termination, it automatically switches to voltage peak detection if the battery pack is not provided with a temperature sensing input (NTC). In this way both packages, with and without temperature sensor, can be used randomly independent of the applied full detection method. Besides T/t and/or
voltage peak detection, fast charging is also protected by temperature cut-off and time-out.
To avoid false fast charge termination by peak voltage detection or T/t, full detection is disabled during a short hold-off period at the start of a fast charge session. After fast charge termination, the battery is extra charged by a top-off period. During this period of approximately one hour, the charge current is lowered thus allowing the battery to be charged to nearly 100% before the system switches over to standby.
After the battery has been charged to nearly 100% by the top-off period, discharge of the battery (caused by a load or by the self-discharge) can be avoided by voltage regulation or by trickle charge.
If batteries are charged in combination with a load, the TEA1102x can be programmed to apply voltage regulation during the standby mode. In this way, discharge of the battery caused by self-discharge or by an eventual load is avoided. The regulating voltage is adjustable to the voltage characteristic of the battery. For battery safety the charge current is limited and the temperature is monitored during voltage regulation. If a trickle charge is applied, the self-discharge of the battery will be compensated by a pulsating charge current.
To avoid the so called ‘memory effect’ in NiCd batteries, a refresh can be manually activated.The discharge current is regulated by the IC in combination with an external power transistor. After discharging the battery to 1 V per cell, the system automatically switches over to fast charge.
CHARGING LiION/SLA BATTERIES Charging these types of batteries differs considerably from
charging NiCd and NiMH batteries. The batteries will be charged with a charge current of 0.15 CA if their cell voltage is below the minimum voltage of 0.9 V for Lilon or
0.45 V for SLA. With batteries in good condition the battery voltage will rise above 0.9 V in a short period of time. When the batteries are short-circuited the voltage will not rise above 0.9 V within one hour and the system will change over to cut-off, which means that the output drivers AO and PWM are fixed to zero and that battery charge can only be started again after a power-on reset. If the battery voltage of a good condition battery is above the minimum level of 0.9 V the battery will be charged with the programmed fast charge current.
If Lilon or SLA batteries are used, ‘full’ is detected when the battery voltage reaches 4.1 and 2.45 V respectively. At this point the TEA1102x switches from current regulation to voltage regulation (fill-up mode).
1999 Jan 27 7
Philips Semiconductors Preliminary specification
Fast charge ICs for NiCd, NiMH, SLA and LiIon
TEA1102; TEA1102T;
TEA1102TS
After the ‘fill-up’ period the charge current is not regulated, which means that the output drivers AO and PWM are fixed to zero. When the battery voltage becomes less than 3 V for Lilon and 1.5 V for SLA, the IC enters the fast charge mode again.
FUNCTIONAL DESCRIPTION Control logic
The main function of the control logic is to support the communication between several blocks. It also controls the charge method, initialization and battery full detection. The block diagram of the TEA1102x is illustrated in Fig.1.
Conditioning charge method and initializations
At system switch-on, or at battery insertion, the control logic sets the initialization mode in the timer block. After the initialization time the timer program pins can be used to indicate the charging state using several LEDs. The charge method is defined at the same time by the following methods:
If the FCT pin is 0 or 1.25 V, indicating that SLA or LiIon
batteries have to be charged, the battery will be charged by limit current and limit voltage regulation. Without identification (FCT pin floating), the system will charge the battery according to the charge characteristic of NiCd and NiMH batteries.
The standby charge method (NiCd and NiMH), trickle charge or voltage regulation, is defined by the input pin V
stb
. By biasing this voltage with a set voltage, the output
voltage will be regulated to the V
stb
set voltage. If this pin is connected to VS, or no NTC is connected the system applies trickle charge.
If pin RFSH is connected to ground by depressing the switch, the TEA1102x discharges the battery via an external transistor connected to pin RFSH. The discharge current is regulated with respect to the external (charge) sense resistor (R
sense
). End-of-discharge is reached when the battery is discharged to 1 V per cell. Refreshing the battery can only be activated during charging of NiCd and NiMH batteries. When charging LiIon and SLA batteries, discharge before charge is disabled.
The inhibit mode has the main priority. This mode is activated when the V
stb
input pin is connected to ground. Inhibit can be activated at any charge/discharge state, whereby the output control signals will be zero, all LEDs will be disabled and the charger timings will be set on hold. Table 1 gives an operational summary.
Table 1 Functionality of program pins
Notes
1. Where X = don’t care.
2. Not low means floating or high.
3. The NTC voltage has been to be less than 3.3 V, which indicates the presence of an NTC.
4. The NTC voltage is outside the window for NTC detection.
5. V
stb
has to be floating or set to a battery regulating voltage in accordance with the specification.
FUNCTION FCT NTC RFSH V
stb
Inhibit X
(1)
X
(1)
X
(1)
low
LiIon and SLA detection low X
(1)
X
(1)
X
(1)
Refresh (NiCd and NiMH) not low
(2)
X
(1)
low not low
T/t detection floating note 3 not low not lowT/t and voltage peak detection high note 3 not low not low
Voltage peak detection not low note 4 not low not low Trickle charge at standby not low X
(1)
not low high
not low note 4 not low not low
Voltage regulation at standby not low note 3 not low floating
(5)
1999 Jan 27 8
Philips Semiconductors Preliminary specification
Fast charge ICs for NiCd, NiMH, SLA and LiIon
TEA1102; TEA1102T;
TEA1102TS
Supply block
The supply block delivers the following outputs:
A power-on reset pulse to reset all digital circuitry at battery insertion or supply switch-on. After a general reset the system will start fast charging the battery.
A 4.25 V stabilized voltage source (VS) is externally available. This source can be used to set the thermistor biasing, to initialize the programs, to supply the external circuitry for battery voltage based charge indication and to supply other external circuitry.
A 4.25 V bias voltage (V
sl
) is available for use for more indication LEDs. This output pin will be zero during the initialization period at start-up, thus avoiding any interference of the extra LEDs when initializing.
Charge control
The charge current is sensed via a low-ohmic resistor (R
sense
), see Fig.4. A positive voltage is created across
resistor Rb by means of a current source I
ref
which is set by
R
ref
in the event of fast charge and by an internal bias current source in the event of top-off and trickle charge (IIB), see Fig.1. The positive node of Rb will be regulated to zero via error amplifier A1, which means that the voltage across Rb and R
sense
will be the same. The fast charge
current is defined by the following equation:
(1)
The output of amplifier A1 is available at the loop stability pin LS, consequently the time constant of the current loop can be set. When V
peak
(NiCD and NiMH) is applied, the current sensing for the battery voltage will be reduced, implying that the charge current will be regulated to zero during:
(2)
Actually battery voltage sensing takes place in the last oscillator cycle of this period.
To avoid modulation on the output voltage, the top-off charge current is DC regulated, defined by the following equation:
(3)
where:
(4)
The top-off charge current will be approximately 0.15 CA, which maximizes the charge in the battery under safe and slow charging conditions. The top-off charge period will be approximately one hour, so the battery will be extra
I
fastRsense
× RbI
ref
×=
t
sense
210POD× t
osc
×=
I
top off
R
sense
× Rb310
6
××=
t
top off
227TOD× t
osc
×=
charged with approximately 0.15 Q. In this way the battery is fully charged before the system switches over to standby.
When pin 1 (V
stb
) is connected to VS, or no NTC is connected the system compensates the (self) discharge of the battery by trickle charge. The trickle charge current will be pulsating, defined by the following equation:
(5)
During the non current periods at trickle charge the charge current is regulated to zero, so that the current for a load connected in series across the battery with the sense resistor will be supplied by the power supply and not by the battery.
If at pin 1 (V
stb
) a reference voltage is set in accordance with the specification, and no NTC is connected the charge mode will switch over from current to voltage regulation after top-off. The reference regulating voltage can be adjusted to the battery characteristic by external resistors connected to pin V
stb
.
This reference voltage has to be selected in such a way that it equals the rest voltage of the battery. By using voltage regulation, the battery will not be discharged at a load occurrence. If the V
stb
input pin is floating, the TEA1102x will apply voltage regulation at 1.325 V during the standby mode (NiCd and NiMH). The current during voltage regulation is limited to 0.5 CA. If the battery charge current is maximized to 0.5 CA for more than 2 hours charging will be stopped. Moreover, if the temperature exceeds T
max
, charging will be stopped completely. As voltage regulation is referred to one cell, the voltage on the V
bat
pin must be the battery voltage divided by the
number of cells (NiCd and NiMH). For LiIon or SLA batteries, the battery is extra charged
after full detection by constant voltage regulation during a certain fill-up period. LiIon and SLA batteries have to identify themselves by an extra pin on the battery pack to ground, which is connected via a resistor to pin 11 (FCT). As the battery voltage sense (V
bat
) has to be normalized to
a one cell voltage of NiCd and NiMH packages, the V
bat
input pin will be regulated to 1.367 and 1.633 V during fill-up for LiIon and SLA respectively. In this way this system can accept a mixture of one LiIon, two SLA and three NiCd or NiMH packages.
After fill-up, charging of LiIon or SLA batteries is disabled. The battery charge is then fixed to zero, ensuring maximum life-cycle of the battery.
Because of a fixed zero charge current, the battery will be discharged if a load is applied.
I
trickleRsense
× R
b
15 16
------
× 10
6–
×=
1999 Jan 27 9
Philips Semiconductors Preliminary specification
Fast charge ICs for NiCd, NiMH, SLA and LiIon
TEA1102; TEA1102T;
TEA1102TS
To ensure an eventual load during all charging states, the fast charge mode will be entered again if the battery voltage drops below 15 V for SLA or 3 V for Lilon.
When charging, the standby mode (LiIon and SLA) can only be entered after a certain period of time depending on time-out. The same applies for charging NiCd or NiMH batteries. To support full test of the TEA1102x at application, the standby mode is also entered when V
bat<Vbat(l)
at fill-up or top-off respectively.
Timer
The timing of the circuit is controlled by the oscillator frequency.
The timer block defines the maximum charging time by ‘time-out’. At a fixed oscillator frequency, the time-out time can be adapted by the Programmable Time-out Divider (PTD) using the following equation.
(6)t
time out
226POD× PTD× t
osc
×=
The time-out timer is put on hold by low voltage, temperature protection and during the inhibit mode. The Programmable Oscillator Divider (POD) enables the oscillator frequency to be increased without affecting the sampling time and time-out. Raising the oscillator frequency will reduce the size of the inductive components that are used.
At fast charging, after battery insertion, after refresh or supply interruption, the full detector will be disabled for a period of time to allow a proper start with flat or inverse polarized batteries. This hold-off period is disabled at fast charging by raising pin V
stb
to above ±5 V (once). So for test options it is possible to slip the hold-off period. The hold-off time is defined by the following equation:
(7)
Table 2 gives an overview of the settings of timing and discharge/charge currents.
t
hold off
25–t
time out
×=
Table 2 Timing and current formulae
SYMBOL DESCRIPTION FORMULAE
t
osc
timing see Fig.3
T
sampling
(T/t) NTC voltage sampling frequency
2
17
× POD × PSD × t
osc
T
sampling
(V
peak
) battery voltage sampling frequency
2
16
× POD × t
osc
t
top-off 2
27
× POD × t
osc
t
time-out 2
26
× POD × PTD × t
osc
t
hold-off 2
5
× t
time-out
t
LED
inhibit or protection
2
14
× POD × t
osc
t
sense 2
10
× POD × t
osc
t
switch 2
21
× POD × PTD × t
osc
I
fast
charge/discharge currents
I
top-off
I
trickle
I
load-max
I
RFSH
R
b
R
sense
-----------------
V
ref
R
ref
----------
×
R
b
R
sense
-----------------
3× 10
6–
×
R
b
R
sense
-----------------
15 16
------
× 10
6–
×
R
b
R
sense
-----------------
40× 10
6–
×
100 mV
R
sense
--------------------
Loading...
+ 19 hidden pages