Philips TDA3672 Datasheet

INTEGRATED CIRCUITS

DATA SH EET

TDA3672

Very low dropout voltage/quiescent
current 3.0 V voltage regulator with
enable

Preliminary specification
File under Integrated Circuits, IC01

2000 Apr 26

Philips Semiconductors Preliminary specification

Very low dropout voltage/quiescent current

3.0 V voltage regulator with enable

FEATURES

• Fixed 3.0 V, 100 mA regulator with enable function

• Supply voltage range up to 33 V (45 V)

• Very low quiescent current of 15 µA (typical value)

• Very low dropout voltage

• High ripple rejection

• Very high stability:

– Electrolytic capacitors:Equivalent Series Resistance

(ESR) < 30 Ω at I

– Other capacitors: 100 nF at 200 µA ≤ I

≤ 25 mA (see Fig.6)

REG

REG

≤ 100 mA.

• Pin compatible family TDA3672 to TDA3676

• Protections:

– Reverse polarity safe (down to −25 V without high

reverse current)

– Negative transient of 50 V (RS=10Ω and

t < 100 ms)

– Able to withstand voltages up to 18 V at the output

– ESD protection on all pins
– DC short-circuit safe to ground and VP of the

– Temperature protection (at Tj> 150 °C).

GENERAL DESCRIPTION

The TDA3672 is a fixed 3.0 V voltage regulator with very
lowdropoutvoltageandquiescentcurrent,which operates
over a wide supply voltage range.

The IC is available as:
TDA3672AT: VP≤ 45 V; −40 °C ≤ T

SO8 package (automotive).

(supply line may be short-circuited)

regulator output

amb

TDA3672

≤ +125 °C and

QUICK REFERENCE DATA

SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT

Supply

V

P

I

q

supply voltage regulator on 3 14.4 45 V
quiescent supply current VP= 14.4 V; I

V

=5V

I(EN)

REG

= 0 mA;

− 15 30 µA

Voltage regulator

V

REG

V

REG(drop)

output voltage 7.5 ≤ VP≤ 22 V; I

5.5 V ≤ V
V

= 14.4 V; 0.5 mA ≤ I

P

dropout voltage VP= 2.8 V; I

T

amb

P

≤ 85 °C

≤ 45 V; I

REG

= 0.5 mA 2.84 3.0 3.16 V

REG

= 0.5 mA 2.81 3.0 3.19 V

REG

≤ 100 mA 2.81 3.0 3.19 V

REG

=50mA;

− 0.18 0.3 V

ORDERING INFORMATION

TYPE

NUMBER

NAME DESCRIPTION VERSION

PACKAGE

TDA3672AT SO8 plastic small outline package; 8 leads; body width 3.9 mm SOT96-1

2000 Apr 26 2

Philips Semiconductors Preliminary specification

Very low dropout voltage/quiescent current

3.0 V voltage regulator with enable

BLOCK DIAGRAM

handbook, halfpage

V

EN

8

P

5

BAND GAP

TDA3672

2, 3, 6, 7

GND

REGULATOR

THERMAL

PROTECTION

MBL122

TDA3672

1

REG

Fig.1 Block diagram.

PINNING

SYMBOL PIN DESCRIPTION

REG 1 regulator output
GND 2, 3, 6 and 7 ground; note 1
n.c. 4 not connected
EN 5 enable input
V

P

8 supply voltage

Note

1. All pins GND are connected to the lead frame and can
also be used to reduce the total thermal resistance
R

by soldering these pins to a ground plane.

th(j-a)

The ground plane on the top side of the PCB acts like
a heat spreader.

handbook, halfpage

REG

GND

n.c.

1
2
3
4

TDA3672

MBL123

V

8

P

GNDGND

7

GND

6

EN

5

2000 Apr 26 3

Fig.2 Pin configuration.

Philips Semiconductors Preliminary specification

Very low dropout voltage/quiescent current

TDA3672

3.0 V voltage regulator with enable

FUNCTIONAL DESCRIPTION

The TDA3672 is a fixed 3.0 V regulator which can deliver
output currents up to 100 mA. The regulator is available in
an SO8 package with fused centre pins connected to the
lead frame. The regulator is intended for portable, mains,
telephone and automotive applications. To increase the
lifetime of batteries, a specially built-in clamp circuit keeps
the quiescent current of this regulator very low, also in
dropout and full load conditions.

The regulator remains operating down to very low supply
voltages and below this voltage it switches off.

LIMITING VALUES

In accordance with the Absolute Maximum Rating System (IEC 60134).

SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT

V
V
P

T
T
T

P
P(rp)
tot

stg
amb
j

supply voltage − 45 V
reverse polarity supply voltage non-operating −−25 V
total power dissipation temperature of copper area

storage temperature non-operating −55 +150 °C
ambient temperature operating −40 +125 °C
junction temperature operating −40 +150 °C

A temperature protection circuit is included, which
switches off the regulator output at a junction temperature
above 150 °C.

A new output circuit guarantees the stability of the
regulator for a capacitor output circuit with an ESR up
to 20 Ω (see Fig.5). If only a 100 nF capacitor is used, the
regulator is fully stable when I

> 200 µA. This is very

REG

attractive as the ESR of an electrolytic capacitor increases
strongly at low temperatures (no expensive tantalum
capacitor is required).

− 4.1 W

is 25 °C

THERMAL CHARACTERISTICS

SYMBOL PARAMETER CONDITIONS VALUE UNIT

R
R

th(j-a)
th(j-c)

thermal resistance from junction to ambient in free air; soldered in 125 K/W
thermal resistance from junction to case to centre pins; soldered in 30 K/W

QUALITY SPECIFICATION

In accordance with

“SNW-FQ-611E”

.

2000 Apr 26 4

Philips Semiconductors Preliminary specification

Very low dropout voltage/quiescent current

TDA3672

3.0 V voltage regulator with enable

CHARACTERISTICS

VP= 14.4 V; T

SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT

Supply voltage: pin V

V

P

I

q

Enable input: pin EN

V

I(EN)

I

I(EN)

Regulator output: pin REG; note 2
V

REG

V

REG(drop)

V

REG(stab)

∆V

REG(line)

∆V

REG(load)

SVRR supply voltage ripple rejection f

I

REG(crl)

I

LO(rp)

=25°C; measured in test circuit (see Fig.3); unless otherwise specified.

amb

P

supply voltage regulator operating; note 1 3 14.4 45 V
quiescent current VP= 14.4 V; I

V

=0V

I(EN)

= 14.4 V; I

V

P

V

=5V

I(EN)

5.5 V ≤ V

5.5 V ≤ V

P
P

enable input voltage enable off; V

enable on; V

enable input current V

=5V − 0.3 −µA

I(EN)

output voltage 7.5 V ≤ VP≤ 22 V; I

0.5 mA ≤ I
T

amb

5.5 V ≤ V
T

amb

REG

≤ 125 °C

P

≤ 125 °C

dropout voltage VP= 2.8 V; I

T

≤ 85 °C

amb

long-term output voltage

= 0 mA;

REG

= 0 mA;

REG

≤ 22 V; I
≤ 22 V; I

REG
REG

=10mA − 0.2 0.5 mA

REG

=50mA − 1.4 2.5 mA

REG

≤ 0.8 V −1 − +1.0 V
≥ 2.7 V 3.0 − 18 V

= 0.5 mA 2.84 3.0 3.16 V

REG

≤ 100 mA;

≤ 45 V;I

REG

= 0.5 mA;

REG

=50mA;

− 415µA

− 15 30 µA

2.81 3.0 3.19 V

2.81 3.0 3.19 V

− 0.18 0.3 V

− 20 − mV/1000 h

stability
line regulation voltage 6.5 V ≤ VP≤ 22 V; I

6.5 V ≤ V

load output regulation voltage 0.5 mA ≤ I

= 120 Hz; V

i

I

REG

current limit V
output leakage current at

REG

VP= −15 V; V

≤ 45 V; I

P

≤ 50 mA − 10 50 mV

REG

i(ripple)

= 0.5 mA

> 2.5 V 0.17 0.25 − A

REG

= 0.5 mA − 130mV

REG

= 0.5 mA − 150mV

REG

= 1 V (RMS);

50 60 − dB

≤ 0.3 V − 1 500 µA

reverse polarity input

Notes

1. The regulator output will follow V

if VP<V

P

REG+VREG(drop)

.

2. Limiting values as applicable for device type TDA3672AT: VP≤ 45 V and −40 °C ≤ T

2000 Apr 26 5

≤ +125 °C.

amb