Philips TDA3664, TDA3664TT Datasheet
INTEGRATED CIRCUITS
DATA SH EET
TDA3664
Very low dropout voltage/quiescent
current 5 V voltage regulator
Product specification
Supersedes data of 2000 Dec 08
File under Integrated Circuits, IC01
2000 Dec 14
Philips Semiconductors Product specification
Very low dropout voltage/quiescent current
5 V voltage regulator
FEATURES
General
• Fixed 5 V, 100 mA regulator
• Supply voltage range up to 45 V
• Very low quiescent current of 15 µA (typical value)
• Very low dropout voltage
• High ripple rejection
• Very high stability:
– Electrolytic capacitors:Equivalent Series Resistance
(ESR) <22 Ω at worst-case condition
– Other capacitors: 100 nF at 200 µA ≤ I
REG
≤ 100 mA.
• Pin compatible family TDA3662 up to TDA3666.
Protections
• Reverse polarity safe (down to −25 V without high
reverse current)
• Negative transient of 50 V (RS=10Ω and t < 100 ms)
• Able to withstand voltages up to 18 V at the output
(supply line may be short-circuited)
• ESD protection on all pins
• DC short-circuit safe to ground and VP of the regulator
output
• Temperature protection (Tj> 150 °C).
GENERAL DESCRIPTION
TheTDA3664 is a fixed 5 V voltage regulator with very low
dropout voltage/quiescent current, which operates over
a wide supply voltage range.
The regulator is available as:
• TDA3664: SO4 package (automotive)
• TDA3664AT: SO8 package (automotive)
• TDA3664TT: TSSOP8 package (automotive).
Automotive: VP≤ 45 V and −40 °C ≤ T
TDA3664
≤ +125 °C.
amb
QUICK REFERENCE DATA
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
Supply
V
P
I
q
supply voltage regulator on 3 14.4 45 V
quiescent supply current VP= 14.4 V; I
=0mA − 15 30 µA
REG
Voltage regulator
V
REG
regulator output voltage 6 V ≤ VP≤ 22 V; I
8V≤V
0.5 mA ≤ I
≤45 V; I
P
REG
≤ 100 mA;
= 0.5 mA 4.8 5.0 5.2 V
REG
= 0.5 mA 4.75 5.0 5.25 V
REG
4.75 5.0 5.25 V
VP= 14.4 V
V
REG(drop)
dropout voltage VP= 4.5 V; I
T
≤ 85 °C
amb
REG
= 50 mA;
− 0.18 0.3 V
2000 Dec 14 2
Philips Semiconductors Product specification
Very low dropout voltage/quiescent current
TDA3664
5 V voltage regulator
ORDERING INFORMATION
TYPE
NUMBER
NAME DESCRIPTION VERSION
TDA3664 SO4 plastic small outline package; 4 leads; body width 3.5 mm SOT223-1
TDA3664AT SO8 plastic small outline package; 8 leads; body width 3.9 mm SOT96-1
TDA3664TT TSSOP8 plastic thin shrink small outline package; 8 leads; body width 3 mm SOT505-1
BLOCK DIAGRAM
handbook, halfpage
1 (8)
V
P
BANDGAP
PACKAGE
REGULATOR
3 (1)
REG
TDA3664
Pin numbers in brackets refer to the SO8 and TSSOP8 version.
Fig.1 Block diagram.
THERMAL
PROTECTION
2, 4 (3)
MGL809
GND
2000 Dec 14 3
Philips Semiconductors Product specification
Very low dropout voltage/quiescent current
5 V voltage regulator
PINNING
SYMBOL
SO4 SO8 TSSOP8
V
P
1 8 8 supply voltage
GND 2 and 4 3 3 ground
REG 3 1 1 regulator output
n.c. − 2, 4, 5, 6 and 7 2,4, 5, 6 and 7 not connected
handbook, halfpage
GND
4
132
V
P
GND
REG
MGL810
PIN
handbook, halfpage
1
REG
2
n.c. n.c.
GND n.c.
n.c. n.c.
3
4
TDA3664
TDA3664
DESCRIPTION
V
8
P
7
6
5
MDA959
Fig.2 Pin configuration of SO4.
FUNCTIONAL DESCRIPTION
The TDA3664 is a fixed 5 V regulator which can deliver
output currents up to 100 mA. The regulator is available in
SO8, TSSOP8 and SO4 packages. The regulator is
intended for portable, mains, telephone and automotive
applications. To increase the lifetime of batteries,
a specially built-in clamp circuit keeps the quiescent
current of this regulator very low, also in dropout and full
load conditions.
Fig.3 Pin configuration of SO8 and TSSOP8.
Theregulatorremains operational down to very low supply
voltages, below which it switches off.
A temperature protection is included, which switches the
regulator output off at IC temperatures above 150 °C.
A new output structure guarantees the stability of the
regulator with an ESR (worst-case) up to 22 Ω,
see Figs 5 and 6. This is very attractive as the ESR of an
electrolytic capacitor increases strongly at low
temperatures (no expensive tantalum capacitor required).
2000 Dec 14 4
Philips Semiconductors Product specification
Very low dropout voltage/quiescent current
TDA3664
5 V voltage regulator
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 60134).
SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT
V
P
V
P(rp)
P
tot
T
stg
T
amb
T
j
THERMAL CHARACTERISTICS
SYMBOL PARAMETER CONDITIONS VALUE UNIT
R
th(j-a)
R
th(j-c)
supply voltage − 45 V
reverse polarity supply voltage non-operating −−25 V
total power dissipation temperature of copper area
TDA3664AT − 0.8 W
is 25 °C
TDA3664TT − 0.65 W
TDA3664 − 5W
storage temperature non-operating −55 +150 °C
ambient temperature operating −40 +125 °C
junction temperature operating −40 +150 °C
thermal resistance from junction to ambient in free air; soldered in
SO8 155 K/W
TSSOP8 220 K/W
SO4 100 K/W
thermal resistance from junction to case (SO4 only) in free air 25 K/W
QUALITY SPECIFICATION
In accordance with
“SNW-FQ-611E”
.
2000 Dec 14 5
Philips Semiconductors Product specification
Very low dropout voltage/quiescent current
TDA3664
5 V voltage regulator
CHARACTERISTICS
VP= 14.4 V; T
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
Supply voltage
V
P
I
q
Regulator output: pin REG
V
REG
∆V
REG(line)
∆V
REG(load)
SVRR supply voltage ripple
V
REG(drop)
I
REG(crl)
V
REG(stab)
I
LO(rp)
=25°C; measured in test circuit (see Fig.4); unless otherwise specified.
amb
supply voltage regulator operating; note 1 3 14.4 45 V
quiescent current VP= 4.5 V; I
V
= 14.4 V; I
P
6V≤V
6V≤V
≤22 V; I
P
≤22 V; I
P
output voltage 8 V ≤ VP≤ 22 V, I
=25°C
T
amb
8V≤V
≤22 V, I
P
0.5 mA ≤ I
6V≤V
≤45 V 4.75 5.0 5.25 V
P
line regulation voltage 8 V ≤ VP≤ 16 V; I
7V≤V
7V≤V
≤22 V; I
P
≤45 V; I
P
load regulation voltage 0.5 mA ≤ I
f
= 120 Hz; V
i
rejection
I
REG
= 0.5 mA
dropout voltage VP= 4.5 V; I
current limit V
> 4.5 V 0.17 0.25 − A
REG
=0mA − 10 −µA
REG
=0mA − 15 30 µA
REG
=10mA − 0.2 0.5 mA
REG
= 50 mA; note 2 − 1.4 2.5 mA
REG
= 0.5 mA;
REG
= 0.5 mA 4.75 5.0 5.25 V
REG
≤ 100 mA; note 2 4.75 5.0 5.25 V
REG
= 0.5 mA − 110mV
REG
= 0.5 mA − 130mV
REG
= 0.5 mA − 150mV
REG
≤ 50 mA − 10 50 mV
REG
= 1 V (RMS);
i(ripple)
= 50 mA; T
REG
≤ 85 °C − 0.18 0.3 V
amb
4.8 5.0 5.2 V
50 60 − dB
long-term stability − 20 − mV/1000 h
output leakage current
VP= −15 V, V
≤ 0.3 V − 1 500 µA
REG
at reverse polarity
Notes
1. The regulator output will follow V
2. TDA3664TT: I
≤ 15 mA at T
REG
if VP<V
P
amb
REG+VREG(drop)
≤ 125 °C; I
≤ 30 mA at T
REG
2000 Dec 14 6
.
≤ 85 °C.
amb
Loading...