INTEGRATED CIRCUITS
DATA SH EET
TDA3617
Multiple voltage regulator
Product specification
Supersedes data of 1999 Jul 14
File under Integrated Circuits, IC01
2000 Oct 13
Philips Semiconductors Product specification
Multiple voltage regulator TDA3617
FEATURES
General
• Three VP-state controlled regulators
(regulators 1, 2 and 3)
• Very good stability and noise behaviour
• Separate controlpins for switching regulators 1, 2 and 3
• Supply voltage range from −18 to +50 V
• Low quiescent current (when regulators 1, 2 and 3 are
switched off)
• High ripple rejection
• Hold output for indicating regulator 1 and/or 2 and/or 3
out-of-regulation.
Protections
• Reverse polarity safe (down to −18 V without high
reverse current)
• Able to withstand voltages up to 18 V at the outputs
(supply line may be short circuited)
• ESD protection on all pins
• Thermal protection
• Load dump protection
• Foldback current limit protection for
regulators 1, 2 and 3
• DC short-circuit safe to ground and VP for all regulator
outputs.
GENERAL DESCRIPTION
The TDA3617 is a multiple output voltage regulator with
three independent regulators. It contains:
1. Three fixed voltage regulators with foldback current
protection (regulators 1, 2 and 3)
2. A supply pin that can withstand load dump pulses and
negative supply voltages
3. Independent enable inputs for regulators 1, 2 and 3
4. Local temperature protection for regulator 3
5. A hold output that can be used to interface with a
microprocessor. The hold indicates that the selected
output voltages are available and within their ranges.
QUICK REFERENCE DATA
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
Supply
V
P
supply voltage
operating 9.5 14.4 17.5 V
jump start t ≤ 10 minutes −−30 V
I
q(tot)
T
j
load dump protection for 50 ms; t
total quiescent current standby mode − 540µA
junction temperature −−175 °C
≥ 2.5 ms −−50 V
r
Voltage regulators
V
V
V
REG1
REG2
REG3
output voltage regulator 1 1 mA ≤ I
output voltage regulator 2 1 mA ≤ I
output voltage regulator 3 1 mA ≤ I
≤ 1.3 A 8.55 9.0 9.45 V
REG1
≤ 600 mA 4.75 5.0 5.25 V
REG2
≤ 300 mA 3.14 3.3 3.46 V
REG3
ORDERING INFORMATION
TYPE
NUMBER
NAME DESCRIPTION VERSION
PACKAGE
TDA3617J DBS9P plastic DIL-bent-SIL power package; 9 leads (lead length 7.7 mm) SOT157-4
2000 Oct 13 2
Philips Semiconductors Product specification
Multiple voltage regulator TDA3617
BLOCK DIAGRAM
handbook, full pagewidth
(14.4 V)
V
P
V
en1
V
en2
V
en3
3
2
9
1
TEMPERATURE
LOAD DUMP
PROTECTION
&
&
&
TDA3617
REGULATOR 1
REGULATOR 2
REGULATOR 3
8
GND
HOLD
4
6
5
7
MGL589
(9 V/1.3 A)
(5 V/600 mA)
(3.3 V/300 mA)
REG1
REG2
REG3
HOLD
PINNING
SYMBOL PIN DESCRIPTION
V
en3
V
en1
V
P
1 enable regulator 3 input
2 enable regulator 1 input
3 supply voltage
REG1 4 regulator 1 output
REG3 5 regulator 3 output
REG2 6 regulator 2 output
HOLD 7 hold output
GND 8 ground
V
en2
9 enable regulator 2 input
Fig.1 Block diagram.
handbook, halfpage
1
V
en3
2
V
en1
3
V
P
4
REG1
5
REG3
REG2
HOLD
GND
V
en2
TDA3617
6
7
8
9
MGL590
Fig.2 Pin configuration.
2000 Oct 13 3
Philips Semiconductors Product specification
Multiple voltage regulator TDA3617
FUNCTIONAL DESCRIPTION
The TDA3617 is a multiple output voltage regulator with
threeindependent switchable regulators. Whenthesupply
voltageis available (VP> 4.5 V),regulators 1, 2 and 3 can
be operated by means ofthree independent enable inputs.
Schmitt trigger functions are included to switch the
regulators off at low battery voltage (VP< 4 V).
A hysteresis is included to avoid random switching.
All output pins are fully protected. The regulators are
protected against load dump (the regulators switch off at
VP> 20 V) and short circuit (foldback current protection).
handbook, full pagewidth
V
enable
regulator 1
regulator 1
18.0 V
9.4 V
P
4.5 V
4.0 V
≥1.8 V
≤1.2 V
9.0 V
0 V
load dump
The TDA3617 has a hold circuit which indicates when one
of the regulators is out-of-regulation. The hold function is
disabled when all the enableinputs are LOW (TDA3617 in
standby mode). The HOLD output (open-collector output)
can be wired OR-ed with other hold outputs of other
regulator parts (e.g. TDA3618). When all the regulators of
theTDA3617 are disabled (switched off),the HOLD output
willbe high ohmic. Because ofthis feature, the hold willnot
influence the hold information when wired OR-ed with
other regulator parts.
Figure 3 shows the total timing of a semi-on/off logic set.
Figure 4 shows the total timing of the HOLD signal.
enable
regulator 2
regulator 2
enable
regulator 3
regulator 3
≥1.8 V
≤1.2 V
5.0 V
0 V
≥1.8 V
≤1.2 V
3.3 V
0 V
MGL621
Fig.3 Timing diagrams of a semi-on/off logic set.
2000 Oct 13 4
Philips Semiconductors Product specification
Multiple voltage regulator TDA3617
handbook, full pagewidth
V
P
enable
regulator
2 and/or 3
enable
regulator 1
regulator
output
2 and/or 3
regulator
output 1
temperature
protection
>150 °C
HOLD
active
passive
out of
regulation
out of
regulation
short
circuit
out of
regulation
Fig.4 Timing diagrams of the HOLD signal.
load dump
MGL622
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 60134).
SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT
V
P
supply voltage
operating − 17.5 V
jump start t ≤ 10 minutes − 30 V
V
bat(rp)
P
tot
T
stg
T
amb
T
j
load dump protection for 50 ms; t
reverse polarity battery voltage non-operating −−18 V
total power dissipation − 62 W
storage temperature non-operating −55 +150 °C
ambient temperature operating −40 +85 °C
junction temperature operating − 175 °C
≥ 2.5 ms − 50 V
r
THERMAL CHARACTERISTICS
SYMBOL PARAMETER CONDITIONS VALUE UNIT
R
R
th(j-c)
th(j-a)
thermal resistance from junction to case 2 K/W
thermal resistance from junction to ambient in free air 50 K/W
QUALITY SPECIFICATION
In accordance with
“SNW-FQ-611-E”
.
2000 Oct 13 5