Philips tda1558 DATASHEETS
INTEGRATED CIRCUITS
DATA SH EET
TDA1558Q
2 x 22 W or 4 x 11 W single-ended
car radio power amplifier
Product specification
File under Integrated Circuits, IC01
May 1992
Philips Semiconductors Product specification
2 x 22 W or 4 x 11 W single-ended car
TDA1558Q
radio power amplifier
FEATURES
• Requires very few external components
• Flexibility in use Quad single-ended or stereo BTL
• High output power
• Low offset voltage at output (important for BTL)
• Fixed gain
• Capability to handle high energy on outputs (V
• Protected against electrostatic discharge
• No switch-on/switch-off plop
• Flexible leads
• Low thermal resistance
• Identical inputs (inverting and non-inverting).
• Good ripple rejection
• Mute/stand-by switch
• Load dump protection
• AC and DC short-circuit-safe to ground and V
• Thermally protected
• Reverse polarity safe
P
GENERAL DESCRIPTION
The TDA1558Q is a monolithic integrated class-B output
amplifier in a 17-lead single-in-line (SIL) plastic power
package. The device contains 4 x 11 W single-ended or
2 x 22 W BTL amplifiers and has been primarily developed
for car radio applications.
QUICK REFERENCE DATA
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
V
P
I
ORM
I
tot
I
sb
positive supply voltage range operating 6.0 14.4 18 V
repetitive peak output current −−4A
total quiescent current − 80 − mA
stand-by current − 0.1 100 µA
Stereo BTL application
P
O
output power THD = 10%; 4 Ω−22 − W
SVRR supply voltage ripple rejection 45 −−dB
V
no
| input impedance 25 −−kΩ
|Z
I
|∆V
os
G
v
noise output voltage RS = 0 − 200 −µV
| DC output offset voltage −−250 mV
closed loop voltage gain 45 46 47 dB
Quad single-ended application
P
O
output power THD = 10%; 4 Ω−6−W
THD = 10%; 2 Ω−11 − W
SVRR supply voltage ripple rejection 44 −−dB
V
no
| input impedance 50 −−kΩ
|Z
I
G
v
noise output voltage RS = 0 − 150 −µV
closed loop voltage gain 39 40 41 dB
= 0)
P
ORDERING INFORMATION
EXTENDED TYPE
NUMBER
PINS PIN POSITION MATERIAL CODE
TDA1558Q 17 DIL plastic SOT243R
Note
1. SOT243-1; 1996 August 21.
May 1992 2
PACKAGE
(1)
Philips Semiconductors Product specification
2 x 22 W or 4 x 11 W single-ended car
radio power amplifier
handbook, full pagewidth
input 1
input 2
1
60 kΩ
183 Ω
60 kΩ
2
183 Ω
stand-by
switch
mute switch
VA
mute switch
VA
CM
CM
V
P
513
6
8
14
TDA1558Q
output 1
output 2
mute/stand-by
supply voltage
ripple rejection
input 3
input 4
internal
reference
voltage
4
17
16
15
3
signal ground
reference
voltage
x1
60 kΩ
183 Ω
60 kΩ
183 Ω
15 kΩ
15 kΩ
mute
switch
VA
mute
switch
VA
not connected
CM
CM
9
Fig.1 Block diagram.
mute
switch
TDA1558Q
11
power ground
12
output 3
10
output 4
7
MCD328 - 1
May 1992 3
Philips Semiconductors Product specification
2 x 22 W or 4 x 11 W single-ended car
radio power amplifier
PINNING
SYMBOL PIN DESCRIPTION
−INV1 1 non-inverting input 1
INV2 2 inverting input 2
GND 3 ground (signal)
SVRR 4 supply voltage ripple rejection
V
P1
OUT1 6 output 1
GND1 7 power ground 1
OUT2 8 output 2
n.c. 9 not connected
OUT4 10 output 4
GND2 11 power ground 2
OUT3 12 output 3
V
P2
M/SS 14 mute/stand-by switch
V
ref
INV3 16 inverting input 3
−INV4 17 non-inverting input 4
FUNCTIONAL DESCRIPTION
The TDA1558Q contains four identical amplifiers with
differential input stages (two inverting and two
non-inverting), and can be used for single-ended or BTL
applications. The gain of each amplifier is fixed at 40 dB
(46 dB in BTL). Special features of this device are:
a. mute/stand-by switch
low stand-by current (< 100 µA)
low mute/stand-by switching current (low cost supply
switch)
mute facility.
5 supply voltage
13 supply voltage
15 internal reference voltage
handbook, halfpage
1
– INV1
2
INV2
3
GND
SVRR
4
V
5
P1
OUT1
6
GND1
7
OUT2
8
P2
ref
TDA1558Q
9
10
11
12
13
14
15
16
17
MCD325 - 1
n.c.
OUT4
GND2
OUT3
V
M / SS
V
INV3
– INV4
Fig.2 Pin configuration.
TDA1558Q
b. the harmonic distortion at low frequencies can be
decreased by connecting two diodes at pin 15 to ground or
a zener diode of 1.5 V.
May 1992 4
Loading...