INTEGRATED CIRCUITS
TDA1557Q
2 x 22 W BTL stereo car radio power amplifier with speaker protection
Product specification |
|
May 1992 |
|||||
File under Integrated Circuits, IC01 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Philips Semiconductors |
Product specification |
|
|
2 x 22 W BTL stereo car radio power
TDA1557Q
amplifier with speaker protection
·Requires very few external components
·High output power
·Low offset voltage at output
·Fixed gain
·Good ripple rejection
·Mute/stand-by switch
·Load dump protection
·AC and DC short-circuit-safe to ground and VP
·Thermally protected
·Reverse polarity safe
·Capability to handle high energy on outputs (VP = 0)
·Protected against electrostatic discharge
·No switch-on/switch-off plop
·Flexible leads
·Low thermal resistance.
The TDA1557Q is a monolithic integrated class-B output amplifier in a 13-lead single-in-line (SIL) plastic power package. The device contains 2 ´ 22 W amplifiers in BTL configuration and has been primarily developed for car radio applications.
SYMBOL |
PARAMETER |
CONDITIONS |
MIN. |
TYP. |
MAX. |
UNIT |
|
|
|
|
|
|
|
VP |
positive supply voltage range |
|
|
|
|
|
|
|
operating |
6.0 |
14.4 |
18 |
V |
|
|
non-operating |
- |
- |
30 |
V |
|
|
load dump |
- |
- |
45 |
V |
IORM |
repetitive peak output current |
|
- |
- |
4 |
A |
|
|
|
|
|
|
|
Itot |
total quiescent current |
|
- |
80 |
- |
mA |
Isb |
stand-by current |
|
- |
0.1 |
100 |
mA |
Isw |
switch-on current |
|
- |
- |
60 |
mA |
ïZIï |
input impedance |
|
25 |
- |
- |
kW |
TXTAL |
crystal temperature |
|
- |
- |
+150 |
°C |
Stereo application |
|
|
|
|
|
|
|
|
|
|
|
|
|
PO |
output power |
THD = 10%; 4 W |
- |
22 |
- |
W |
SVRR |
supply voltage ripple rejection |
RS = 0; f = 100 Hz to 10 kHz |
45 |
- |
- |
dB |
ïDVOï |
DC output offset voltage |
|
- |
- |
250 |
mV |
a |
channel separation |
|
40 |
- |
- |
dB |
|
|
|
|
|
|
|
ïDGvï |
channel unbalance |
|
- |
- |
1 |
dB |
Gv |
closed loop voltage gain |
|
45 |
46 |
47 |
dB |
EXTENDED TYPE |
|
|
PACKAGE |
|
|
|
|
|
|
|
|
NUMBER |
PINS |
PIN POSITION |
|
MATERIAL |
CODE |
|
|
||||
|
|
|
|
|
|
TDA1557Q |
13 |
DIL |
|
plastic |
SOT141R |
|
|
|
|
|
|
Note
1. SOT141-6; 1996 August 23.
May 1992 |
2 |
Philips Semiconductors |
Product specification |
|
|
2 x 22 W BTL stereo car radio power
TDA1557Q
amplifier with speaker protection
|
|
|
|
POWER |
3 |
10 |
|
|
|
mute switch |
|
STAGE |
|
VP |
|
|
1 |
CM |
|
|
|
||
input 1 |
|
|
|
|
|
|
|
|
|
VA |
|
|
|
4 |
output 1A |
|
|
|
|
|
|
||
|
30 kΩ |
|
|
|
|
|
|
|
183 Ω |
18.1 kΩ |
|
|
|
|
|
|
|
|
|
POWER |
|
|
|
|
|
mute switch |
|
STAGE |
|
|
|
|
|
CM |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
VA |
|
|
|
6 |
output 1B |
|
|
|
|
|
|
||
|
183 Ω |
18.1 kΩ |
|
|
|
|
|
|
|
TDA1557Q |
|
|
|
|
|
|
|
VP |
|
|
|
|
|
|
|
|
|
|
|
11 |
mute/stand-by |
|
stand-by |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
input |
switch |
|
|
stand-by |
|
|
|
12 |
|
|
|
|
|
||
reference |
|
|
reference |
|
|
|
|
VA |
|
|
|
|
|
||
voltage |
|
|
voltage |
|
|
|
|
|
|
15 kΩ |
|
mute |
|
|
|
|
|
|
switch |
|
|
|
|
|
|
|
|
|
|
|
|
|
x1 |
|
|
|
loudspeaker |
|
|
|
|
|
|
|
protection |
|
|
|
|
15 kΩ |
|
|
|
|
|
|
|
mute |
|
|
|
|
|
|
|
reference |
POWER |
|
|
|
|
|
|
voltage |
|
|
|
|
|
|
|
|
STAGE |
|
|
|
|
|
|
mute switch |
|
|
|
|
|
|
13 |
CM |
|
|
|
|
|
input 2 |
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
VA |
|
|
|
9 |
output 2B |
|
|
|
|
|
|
||
|
30 kΩ |
|
|
|
|
|
|
|
183 |
18.1 kΩ |
|
|
|
|
|
|
Ω |
|
|
POWER |
|
|
|
|
|
|
|
|
|
|
|
|
|
mute switch |
|
STAGE |
|
|
|
|
|
CM |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
input |
VA |
|
|
|
7 |
output 2A |
|
|
|
|
|
|||
|
reference |
|
|
|
|
|
|
|
voltage |
|
|
|
|
|
|
|
183 |
18.1 kΩ |
|
|
|
|
|
|
Ω |
|
|
|
|
|
|
|
2 |
|
|
5 |
8 |
|
|
|
|
|
|
|
|
MCD324 - 1 |
|
|
signal ground |
|
|
power ground |
|
|
Fig.1 Block diagram.
May 1992 |
3 |