Philips TDA1519AQ-N2, TDA1519A-N2 Datasheet

DATA SH EET

Product specification
File under Integrated Circuits, IC01

May 1992

INTEGRATED CIRCUITS

TDA1519A

22 W BTL or 2 x 11 W stereo car
radio power amplifier

May 1992 2

Philips Semiconductors Product specification

22 W BTL or 2 x 11 W stereo car radio
power amplifier

TDA1519A

GENERAL DESCRIPTION

The TDA1519A is an integrated class-B dual output amplifier in a 9-lead single in-line (SIL) plastic power package.
The device is primarily developed for car radio applications.

Features

• Requires very few external components for Bridge Tied
Load (BTL)

• Stereo or BTL application

• High output power

• Low offset voltage at output (important for BTL)

• Fixed gain

• Good ripple rejection

• Mute/stand-by switch

• Load dump protection

• AC and DC short-circuit-safe to ground and V

P

• Thermally protected

• Reverse polarity safe

• Capability to handle high energy on outputs (VP= 0 V)

• No switch-on/switch-off plop

• Protected against electrostatic discharge

• Low thermal resistance

• Identical inputs (inverting and non-inverting)

• Compatible with TDA1519B (except output power).

QUICK REFERENCE DATA

PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT

Supply voltage range

operating V

P

6.0 14.4 17.5 V

non-operating V

P

−−30 V

load dump protected V

P

−−45 V

Repetitive peak output current I

ORM

−−4A

Total quiescent current I

tot

− 40 80 mA

Stand-by current I

sb

− 0.1 100 µA

Switch-on current I

sw

−−40 µA

Input impedance

BTL |ZI|25−−kΩ
stereo |Z

I

|50−−kΩ

Stereo application

Output power THD = 10%; 4 Ω P

o

− 6 − W

THD = 10%; 2 Ω P

o

− 11 − W
Channel separation α 40 −−dB
Noise output voltage V

no(rms)

− 150 −µV

May 1992 3

Philips Semiconductors Product specification

22 W BTL or 2 x 11 W stereo car radio
power amplifier

TDA1519A

PACKAGE OUTLINES

9 lead SIL; plastic power (SOT131); SOT131-2; 1996 July 22.
9-lead SIL-bent-to-DIL; plastic power (SOT157); SOT157-2; 1996 July 22.

BTL application

Output power THD = 10%; 4 Ω P

o

− 22 − W
Supply voltage ripple rejection R

S

= 0 Ω
f = 100 Hz RR 34 −−dB
f = 1 kHz to 10 kHz RR 48 −−dB

DC output offset voltage |∆V

0

| −−250 mV

Crystal temperature T

c

−−150 °C

PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT

May 1992 4

Philips Semiconductors Product specification

22 W BTL or 2 x 11 W stereo car radio
power amplifier

TDA1519A

Fig.1 Block diagram.

May 1992 5

Philips Semiconductors Product specification

22 W BTL or 2 x 11 W stereo car radio
power amplifier

TDA1519A

PINNING

FUNCTIONAL DESCRIPTION

The TDA1519A contains two identical amplifiers with differential input stages. The gain of each amplifier is fixed at 40 dB.
A special feature of this device is the mute/stand-by switch which has the following features:

• Low stand-by current (< 100 µA)

• Low mute/stand-by switching current (low cost supply switch)

• Mute condition.

RATINGS

Limiting values in accordance with the Absolute Maximum System (IEC 134)

1 NINV non-inverting input
2 GND1 ground (signal)
3 RR supply voltage ripple rejection
4 OUT1 output 1
5 GND2 ground (substrate)
6 OUT2 output 2
7V

P

positive supply voltage
8 M/SS mute/stand-by switch
9 INV inverting input

PARAMETER CONDITIONS SYMBOL MIN. MAX. UNIT

Supply voltage

operating V

P

− 17.5 V

non-operating V

P

− 30 V

load dump protected during 50 ms;

t

r

≥ 2.5 ms

V

P

− 45 V

AC and DC short-circuit-safe voltage V

PSC

− 18 V

Reverse polarity V

PR

− 6V

Energy handling capability at outputs V

P

= 0 V − 200 mJ

Non-repetitive peak output current I

OSM

− 6A

Repetitive peak output current I

ORM

− 4A

Total power dissipation see Fig.2 P

tot

− 25 W

Crystal temperature T

c

− 150 °C

Storage temperature range T

stg

−55 + 150 °C