Headphones
7000 Series
TAA7 306
User manual
Register your product and get support at
www.philips.com/support
Contents
1 Important safety instructions 2
Hearing Safety 2
General information 2
2 Your Bluetooth wireless
earpieces 3
What's in the box 3
Other devices 3
Overview of your Bluetooth
wireless earpieces 4
3 Get started 5
Charge the battery 5
Pair the earpieces with your
Bluetooth device at the rst
time 6
Pair the earpieces with another
Bluetooth device 6
4 Use your headphones 7
Connect the earpieces to your
Bluetooth device 7
Power on/o 7
Manage your calls and music 7
Battery LED indicator on Bluetooth
device 8
LED indicator status 8
Heart rate monitor 9
Awareness mode 9
5 Factory reset the earpieces 9
6 Technical data 10
7 Notice 11
Declaration of conformity 11
Disposal of your old product
and battery 11
Compliance with EMF 12
Environmental information 12
Notice of compliance 12
8 Trademarks 13
9 Frequently asked questions 14
1 Important
General information
safety
instructions
Hearing Safety
Danger
To avoid hearing damage, limit the time you
use headphones at high volume and set the
volume to a safe level. The louder the
volume, the shorter the safe listening time is.
Be sure to observe the following guidelines when using your earpieces.
• Listen at reasonable volumes for
reasonable periods of time.
• Be careful not to adjust the volume
continuously upwards as your
hearing adapts.
• Do not turn up the volume so high
that you can't hear what's around
you.
• You should use caution or temporarily discontinue use in potentially
hazardous situations.
• Excessive sound pressure from
earpieces and headphones can
cause hearing loss.
• Using headphones with both ears
covered while driving is not recommended and may be illegal in some
areas while driving.
• For your safety, avoid distractions
from music or phone calls while in
trac or other potentially dangerous
environments.
To avoid damage or malfunction:
Caution
Do not expose headphones to excessive heat
Do not drop your headphones.
Headphones shall not be exposed to dripping
or splashing.
Do not allow your headphones to be
submerged in water.
Do not use any cleaning agents containing
alcohol, ammonia, benzene, or abrasives.
If cleaning is required use a soft doth, if
necessary dampened with a minimum amount
of water or diluted mild soap, to clean the
product.
The integrated battery shall not be exposed to
excessive heat such as sunshine, re or the
like.
Replacement of a battery with an incorrect
type that can defeat a safeguard;
Disposal of a battery into re or a hot oven, or
mechanically crushing or cutting of a battery,
that can result in an explosion;
Leaving a battery in an extremely high
temperature surrounding environment that
can result in an explosion or the leakage of
ammable liquid or gas;
A battery subjected to extremely low air
pressure that may result in an explosion or the
leakage of ammable liquid or gas.
Never use your headphones when you are
operating a motor vehicle, riding a bicycle, running
or walking in trac areas. It is dangerous and illegal
in many places.
About operating and storage
temperatures and humidity
• Operating temperature: 0°C (32°F)
to 40°C (104°F)
• Storage temperature: -10°C (14°F)
to 45°C (113°F)
• Operating humidity: 8% - 90% RH
(No condensation)
• Storage humidity: 5% - 90% RH
(No condensation)
• Maximum operating altitude:
3000m
• Battery life may be shorter in high
or low temperature conditions.
2 Your
Bluetooth
wireless
earpieces
Congratulations on your purchase, and
welcome to Philips! To fully benet
from the support that Philips oers,
register your product at
www.philips.com/support.
With this Philips wireless headphones,
you can:
• enjoy convenient wireless
handsfree calls;
• enjoy and control wireless music;
• switch between calls and music.
What's in the box
Ear hook x 3 pairs
Carrying pouch
USB charging cable (for charging only)
Quick start guide
Philips True Wireless earpieces
Philips TAA7306
Replaceable rubber ear caps x 3 pairs
Wing-tips x 3pairs
Global Warranty
Safety leaet
Other devices
A mobile phone or device (e.g. notebook, tablet, Bluetooth adapters, MP3
players etc) which supports Bluetooth
and is compatible to the earpieces
(see 'Technical data' on page 10).
Overview of your
Bluetooth wireless
earpieces
4
1
Microphone
2
LED indicator (Earbud)
3
Touch panel
4
Heart rate monitor (HRM) sensor
(Right side only)
5
Operation LED (Charging case)
6
LED indicator ( charging case )
7
USB-C charging slot
8
Reset button
6
7
8
3 Get started
Charge the battery
Note
Before you use your earpieces for the rst
time, place the earpiecess in the charging
case and charge the battery for 3 hours for
optimum battery capacity and lifetime.
Use only the original USB charging cable to
avoid any damage.
Finish your call before charging the earpieces,
as connecting the earpieces for charging will
power the earpieces o.
• Charging process is veried by white
LED light on the earpiecess.
• When the earpieces is fully charged,
the white light goes o.
Tip
Normally, a full charge takes 2 hours (for the
earpieces or charging case).
Charging case
Connect one end of the USB cable into
the charging case, and another end into
the power source.
The charging case starts charging.
• Charging process is veried by the
white LED light next to the USB
socket on the case.
• When the charging case is fully
charged, the light goes o.
Tip
The charging case serves as a portable backup
battery for charging the earpieces. When the
charging case is fully charged, it supports 3 full
recharge cycle for the earpieces.
Earpieces
Place the earpieces in the charging case.
The earpieces start charging.
Pair the earpieces with
your Bluetooth device at
the rst time
Auto Power on: Open the charging
capsule, the earpiecess discharged
and the blue LED indicator ash
with “power on” voice prompt.
Manual Power on: On both earpiecess
press and hold the multi-function
buttons for approxinmately 2 seconds.
1 second
02"
The LED on both earpiecess ashes
in blue for 3 times, and then it
ashes in white.
Both earpiecess are now power on
and are paired with each other.
Loading...