Philips SCF870 User Manual [ar]

SCF870

100% recycled paper 100% 循环再造纸

4203 000 62249 C

使用本产品之前，请仔细阅读本使用说明书，并保留备用

2 3 4 5

6 7 8 9

10 11 12 13

22 23 24

15 16 17

ENGLISH 6

繁體中文 18

简体中文 28

SCF870

ENGLISH

Introduction

Congratulations on your purchase and welcome to Philips AVENT! To fully benet from the support

that Philips AVENT offers, register your product at www.philips.com/welcome. This combined steamer and blender is particularly suitable for preparing small amounts of baby food. The combined steamer and blender supports all parents in preparing fresh meals for their babies with a simple steaming and blending function combined in one appliance.

General description (Fig. 1)

1 Lid with steam hole 2 Sieve 3 Blade unit 4 Jar with blade unit holder 5 Filling opening of water tank 6 Steam outlet on motor unit 7 Locking area for handle 8 Motor unit 9 Steaming light 10 Control knob 11 Valve 12 Spatula 13 Measuring cup 14 Bottom of the appliance with mains cord

Important

Read this user manual carefully before you use the appliance and save it for future reference.

Danger

- Never immerse the motor unit in water or any other liquid, nor rinse it under the tap.

Warning

- Check if the voltage indicated on the appliance corresponds to the local mains voltage before you connect the appliance.

- Do not use the appliance if the plug, the mains cord or the appliance itself is damaged.

- If the mains cord is damaged, you must have it replaced by Philips, a service centre authorised by

Philips or similarly qualied persons in order to avoid a hazard.

- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

- Keep the appliance and its cord out of the reach of children.

- Do not touch the cutting edges of the blade unit when the appliance is plugged in and during cleaning. The cutting edges are very sharp.

- If the blade unit gets stuck, unplug the appliance before you remove the ingredients that block the blade unit.

- The appliance becomes very hot during steaming and may cause burns if touched. Only lift the jar by its handle.

- Beware of hot steam that comes out of the jar during steaming and when you remove its lid.

- Beware of hot steam that comes out of the lling opening of the water tank when you open its lid.

- When the steaming process is nished, hot steam continues to come out of the steam outlet on the motor unit and the steam hole in the lid of the jar for some time. Be careful when you lift the jar off the motor unit.

- If the appliance is used improperly, hot steam could come out of the lling opening. Consult chapter ‘Troubleshooting’ in order to avoid or to solve this.

- Never let the appliance operate unattended.

ENGLISH 7

- Do not disassemble the motor unit for maintenance or cleaning purposes. Take it to an authorised Philips service centre for repair.

Caution

- Never use any accessories or parts from other manufacturers or that Philips does not specically recommend. If you use such accessories or parts, your guarantee becomes invalid.

- Do not place the appliance on or near an operating or still hot stove or cooker.

- Always unplug the appliance and let it cool down before you clean it.

- Never use the jar or any other part of the appliance in a microwave, as the metal parts of the jar handle and blade unit are not suitable for this use.

- Never sterilise the jar or any other part of the appliance in a steriliser or in a microwave, as the metal parts of the jar handle and blade unit are not suitable for this use.

- This appliance is intended for household use only. If the appliance is used improperly or for professional or semi-professional purposes or if it is not used according to the instructions in the user manual, the guarantee becomes invalid and Philips refuses any liability for damage caused.

- Be careful when you pour hot liquid into the beaker, as hot liquid and steam may be ejected and cause scalding.

- Let the appliance cool down for 10 minutes before you steam another batch of ingredients.

- The appliance is not intended for chopping hard ingredients such as ice cubes and sugar cubes.

- Do not let the appliance blend for more than 30 seconds at a time. If you have not nished blending after 30 seconds, switch off the appliance and wait a few seconds before you continue. If the appliance becomes hot, let it cool down for a few minutes before you continue.

- Place the appliance on a stable, horizontal and level surface. Make sure there is enough free space around it to prevent damage to e.g. cabinets or other objects, as the appliance emits hot steam during use.

- Do not use the appliance if it has fallen or is damaged in any way. Take it to an authorised Philips service centre for repair.

- Never put water, other liquids or blended food in the jar for steaming to avoid damage to the appliance.

- Never use the steaming function without water.

- Make sure that you do not overll the water tank (max. 200ml). Do not exceed the maximum level indicated on the measuring cup.

- When you steam ingredients, make sure that you do not overll the jar. Make sure that the top edge of the green blade unit is not covered with food (Fig. 2).

- When you blend liquids, do not exceed the maximum level indicated on the jar (450ml).

- Do not insert any object into the lling opening or the steam outlet.

- Never rell the water tank during the steaming process, as hot water and steam may come out of the appliance as a result.

- Always make sure that the lid has cooled down after steaming before you open it to add more ingredients for blending, if necessar y.

- Do not connect the appliance to an external switching device such as a timer and do not

connect it to a circuit that is regularly switched on and off by the utility. This prevents a hazard

that could be caused by inadvertent resetting of the thermal cut-out.

Always check the temperature of the baby food on the back of your hand before you feed your baby.

- Always check the consistency of the baby food. Make sure there are no chunks in the food.

- When the steaming process (max. 20 minutes) is nished, do not steam or reheat the baby food again.

- Only use the spatula supplied remove the food from the jar.

- Regular descaling prevents damage to the appliance.

- Children shall not play with the appliance.

- Switch off the appliance and disconnect from supply before changing accessories or approaching parts that move in use.

- Take care in handling the sharp blades when emptying the jar and during cleaning.

- Always disconnect the device from supply if it’s left unattended.

- Cleaning and user maintenance shall not be made by children.

ENGLISH8

Safety system

The appliance is equipped with a built-in safety lock. The appliance only functions if you have properly assembled all parts on the motor unit. If all parts are assembled correctly, the built-in safety lock will be unlocked. The appliance is also equipped with overheat protection. Overheating could occur if the time between two steaming processes is too short, if the blending function is used too long or if there are too much ingredients in the jar. If the overheat protection switches off the appliance during use, set the control knob to 0 and let the appliance cool down for a few minutes. After this, you can use the appliance again.

Electromagnetic elds (EMF)

This Philips appliance complies with all applicable standards and regulations regarding exposure to

electromagnetic elds.

Before rst use

1 Remove all packaging material from the appliance.

2 Clean all parts except the motor unit (see chapter ‘Cleaning and maintenance’).

Using the appliance

Always check the temperature of the baby food on the back of your hand before you feed your baby.

Always make sure that the lid has cooled down after steaming before you remove it to add more ingredients for blending, if necessary. Do not exceed the maximum level indicated on the jar.

Empty the water tank before you rell it to start a new steaming process.

Always make sure that the top edge of the green blade unit is not covered with food when you start steaming.

Do not exceed the maximum level indicated on the jar (450ml) when you blend liquids.

This appliance is intended for steaming fresh solid ingredients and then blending them to obtain baby

food. See the recipe booklet for some examples. Normally you would rst steam the ingredients and

then blend them. However, you can also use the appliance for steaming or blending only. When you use the appliance for blending only, skip sections ‘Filling the water tank’ and ‘Steaming’ and only follow the instructions in section ‘Blending’. After blending, never steam already blended food. Never steam the same batch of ingredients for longer than 20 minutes or more than once. This appliance is NOT intended for:

- Defrosting food

- Steaming frozen food

- Steaming already blended food

- Steaming the same ingredients for more than 20 minutes

- Cooking rice and pasta

- Blending ingredients rst and then steaming them

- Heating up uids, e.g. soup or water

- Keeping food warm for several hours

- Reheating food

Filling the water tank

1 Fill the measuring cup with water up to the required level (Fig. 3).

The measuring cup shows millilitres and the corresponding steaming time in minutes. See the separate recipe booklet for the recommended quantities of the recipes.

Note: Do not exceed the maximum level indicated on the measuring cup (200ml) to make sure that you

do not overll the water tank.

ENGLISH 9

Note: We advise you not to use mineral water, as the minerals contained in this type of water cause scale to build up inside the water tank.

2 Pour the water into the lling opening and close the lid (Fig. 4).

Note: Never put anything else than water in the water tank.

Steaming

If certain vegetables and fruits are steamed gently, they are perfect for babies who start to eat solid food. Steaming is the healthiest way of preparing food, as the food retains lots of vitamins and other healthy nutrients.

Note: You can nd recipes and the cooking times required for these recipes in the separate recipe booklet. Note that the recipes are related to the age of the child.

Note: Do not steam frozen ingredients because the appliance cannot heat up frozen food to the temperature required for steaming. Always defrost frozen solid ingredients before you steam them in this appliance. Shake off any excess water from the defrosted ingredients before you put them in the jar.

1 Put the blade unit on the blade unit holder in the jar (Fig. 5).

2 Cut solid ingredients into small pieces (cubes not bigger than 2-3cm) before you put them in

the jar.

Note: Do not process a large quantity of solid ingredients at the same time. Process these ingredients in a series of small batches instead.

3 Put the ingredients in the jar (Fig. 6).

Note: Do not exceed the top edge of the green blade unit.

Note: Never put water or any other liquid in the jar for steaming, to avoid damage to the appliance.

4 Put the valve in the lid (Fig. 7).

Note: Make sure the valve is xed properly.

5 Put the sieve in the lid of the jar (‘click’) (Fig. 8).

6 Place the lid on the jar and turn it clockwise to x it. The small projections on the lid have to

slide into the grooves in the jar. Make sure that the large projection of the lid is placed exactly over the handle of the jar (Fig. 9).

7 Place the jar upside down on the motor unit, i.e. with the lid downwards. Make sure that the

handle is on the right-hand side and that it is attached properly (Fig. 10).

Note: The appliance does not start steaming if the jar and handle are not in the correct position.

8 Turn the control knob to the steaming position.

● The steaming light lights up orange to indicate that the appliance is steaming (Fig. 11).

Hot steam or hot water could burn your ngers. Do not touch and never let children touch hot

parts and steam, as this may cause scalds (Fig. 12).

● The steaming time depends on the amount of water you have put in the water tank. See the table in chapter ‘Ingredients and steaming times’ and the recipe booklet.

● When the steaming process is nished, the appliance produces a buzzing sound and the steaming light goes out.

9 Set the control knob to the off position. Wait 2 minutes until no more steam comes out of

the steam outlet, to avoid scalding by hot steam. (Fig. 13)

Note: If you want to steam another batch of ingredients, let the appliance cool down for 10 minutes before you start steaming again.

ENGLISH10

10 If you want to proceed with blending the steamed food, follow the instructions in section

‘Blending after steaming’ below.

11 Under normal conditions, no water remains in the water tank after steaming. However, in

some situations (e.g. in case of scale build-up inside the water tank, interruption of the steaming process or unintended use), some water could remain in the water tank. In this

case, empty the water tank completely after use to avoid bacterial growth. To descale the

water tank, see chapter ‘Cleaning and maintenance’.

Blending after steaming

1 Grab the jar handle and lift the jar off the motor unit. Turn the jar around and shake it so that

the food falls down onto the blade unit (Fig. 14).

Only touch the jar handle. The lid, bottom and outer surface of the jar are hot (Fig. 15).

2 If necessary, remove the lid and add additional ingredients for blending (e.g. water or oil).

Always make sure that the lid of the jar and the lid of the water tank have cooled down after steaming before you open them to add more ingredients to the jar or to remove the remaining water from the water tank.

After you have put liquids in the jar, never put the jar in the steaming position.

3 Place the jar upright on the motor unit, i.e. with the lid upwards. Make sure the handle is on

the right-hand side and positioned between the two ridges of the locking area (Fig. 16).

4 Turn the control knob to the blending position. Hold the knob in this position until the food

is properly blended (Fig. 17).

Do not let the appliance blend for more than 30 seconds at a time. If you have not nished

blending after 30 seconds, switch off the appliance and wait a few seconds before you continue. If the appliance becomes hot, let it cool down for a few minutes before you continue.

Note: If the ingredients stick to the wall of the jar, switch off the appliance and loosen them with the spatula or add some liquid.

Note: Make sure that the blended baby food has the right consistency (e.g. no lumps) before you serve it.

Note: If the baby food is still too solid, add some uid (e.g. water) until the baby food is soft and smooth.

5 When you have nished blending, simply release the control knob (Fig. 18).

● The knob automatically returns to the off position.

6 Unplug the appliance.

Remove the blade unit. Be careful when you remove the blade unit as it might be hot. Remove

the blended food from the jar. If necessary, use the spatula included with this appliance.

Make sure that the baby food is at a safe temperature for your baby.

8 Under normal conditions, no water remains in the water tank after steaming. However,

in some situations (e.g. in case of scale build-up inside the water tank, interruption of the steaming process or unintended use), some water could remain in the water tank. In this

case, empty the water tank completely after use to avoid bacterial growth. To descale the

water tank, see chapter ‘Cleaning and maintenance’.

Blending without steaming

The appliance is intended for:

- pureeing steamed and cooked ingredients for baby food

- blending uids and fruits for baby drinks

ENGLISH 11

The appliance is not intended for chopping hard ingredients such as ice cubes and sugar cubes.

After you have put liquids in the jar, never put the jar in the steaming position.

Note: When you blend uids, make sure you do not ll the jar beyond the maximum level indication on the jar.

Note: Never steam baby food after you have blended it.

1 Put the blade unit on the blade unit holder in the jar (Fig. 5).

Cut solid ingredients into small pieces (cubes not bigger than 2-3cm) before you put them in the jar.

Tip: Do not process a large quantity of solid ingredients at the same time. Process these ingredients in a series of small batches instead.

3 Put the ingredients in the jar. (Fig. 6)

Note: Do not exceed the top edge of the green blade unit.

4 Put the valve in the lid (Fig. 7).

Note: Make sure the valve is xed properly.

5 Put the sieve in the lid of the jar (‘click’) (Fig. 8).

6 Place the lid on the jar and turn it clockwise to x it. The small projections on the lid have to

slide into the grooves in the jar. Make sure that the large projection of the lid is placed exactly over the handle of the jar. (Fig. 9)

7 Place the jar upright on the motor unit, i.e. with the lid upwards. Make sure the handle is on

the right-hand side and positioned between the two ridges of the locking area (Fig. 16).

8 Turn the control knob to the blending position. Hold the knob in this position for as long as

you need but for not more than 30 seconds (Fig. 17).

Note: If the ingredients stick to the wall of the jar, switch off the appliance and loosen them with the spatula or add some liquid. Do not exceed the maximum level indication on the jar.

Note: Make sure that the blended baby food has the right consistency (e.g. no lumps) before you serve it.

Note: If the baby food is still too solid, add some uid (e.g. water) until the baby food is soft and smooth. Do not exceed the maximum level indication on the jar.

Note: Never steam baby food after you have blended it.

Do not let the appliance blend for more than 30 seconds at a time. If you have not nished

blending after 30 seconds, switch off the appliance and wait a few seconds before you continue. If the motor unit becomes hot, let it cool down for a few minutes before you continue.

9 When you have nished blending, simply release the control knob. (Fig. 18)

● The knob automatically returns to the off position.

10 Unplug the appliance.

Remove the blade unit. Be careful when you remove the blade unit as it might be hot. Remove

the blended food from the jar. If necessary, use the spatula included with this appliance.

Make sure that the baby food is at a safe temperature for your baby.

ENGLISH12

Ingredients and steaming times

Type of food Ingredient Approximate steaming time*

Fruit Apple 5 min

Oranges 10 min

Peach 10 min

Pear 5 min

Pineapple 15 min

Plum 10 min

Vegetables Asparagus 10 min

Broccoli 20 min

Carrot 15 min

Cauliower 15 min

Celery 15 min

Courgette 15 min

Fennel 15 min

French beans 20 min

Leek 15 min

Onion 15 min

Peas 20 min

Pepper 15 min

Potato 20 min

Pumpkin 15 min

Spinach 15 min

Swede 15 min

Sweet potato 15 min

Tomato 15 min

Meat Chicken, beef, lamb, pork etc. 20 min

Fish Salmon, sole, cod, trout etc. 15 min

* All food has to be cut in small cubes, no bigger than 2-3cm.

Note: The measuring cup shows millilitres and the corresponding steaming time in minutes (50ml = 5 min, 100ml = 10 min, 150ml = 15 min, 200ml = 20 min).

ENGLISH 13

Cleaning and maintenance

Clean the appliance after every use.

Never immerse the motor unit in water.

Never use bleach or chemical sterilising solutions/tablets in the appliance.

Never use scouring pads, abrasive cleaning agents or aggressive liquids such as petrol, acetone or alcohol to clean the appliance.

1 Unplug the appliance and remove the jar from the motor unit (Fig. 19).

2 Remove the lid from the jar and turn the lid upside down (Fig. 20).

3 Remove the sieve and the valve from the lid. (Fig. 21)

4 Clean the valve in hot water with some washing-up liquid and rinse it under the tap.

5 Remove the blade unit from the jar (Fig. 22).

6 Clean the blade unit under the tap thoroughly, immediately after use. Make sure you also

rinse the inside of the tube of the blade unit (Fig. 23).

Handle the blade unit very carefully. The cutting edges are very sharp.

Note: If you want to clean the blade unit more thoroughly, you can also place it in the dishwasher after you have rinsed it.

7 Clean the other parts that have come into contact with food in hot water with some

washing-up liquid immediately after use.

Note: All parts, except the motor unit, can also be cleaned in the dishwasher.

8 If necessary, clean the motor unit with a moist cloth.

9 Check if any food particles have entered the water tank. You can do this by looking into the

lling opening to see if there are any food particles in it or by checking if the water has an

unusual colour and by smelling if the water tank produces an unpleasant or a burnt smell. If this is the case, clean the water tank (see section ‘Cleaning the water tank’ in this chapter).

10 Leave the lid of the lling opening open to prevent bacterial growth.

Descaling the water tank

If food particles enter the water tank, they may get stuck onto the heating element in the water tank during the next steaming processes. These particles cannot be removed by just rinsing the water tank. In addition, you have to descale the appliance every four weeks to ensure it continues to work

100% effectively. To reduce scale build-up, it is helpful to use pre-boiled or ltered water in the appliance.

To remove food particles inside the water tank and to descale the appliance, follow the descaling instructions below.

1 Make sure the appliance is switched off.

2 Add 50ml white vinegar (8% acetic acid) to 150ml water.

Note: You can also citric acid based descalers. Do not use other types of descalers.

3 Fill the water tank with the solution of vinegar (or citric acid) and water.

4 Close the lid of the lling opening.

5 Place the empty jar (without any food inside) fully assembled with blade unit and lid on the

motor unit in steaming position (i.e. with the lid pointing downwards).

ENGLISH14

6 Turn the control knob to steaming position.

● The steaming light lights up orange to indicate that the appliance is steaming.

7 Switch off the appliance after 5-6 min of steaming and unplug it.

8 Pour the used solution of white vinegar (8% acetic acid) and water out of the water

tank (Fig. 24).

9 Rinse the water tank and the jar thoroughly with fresh water several times.

10 Fill the tank with 200ml water and let the appliance complete a steaming process of

20 minutes with the empty jar before you use the appliance with food again.

11 Leave the lid of the lling opening open to prevent bacterial growth.

Recycling

- Do not throw away the product with the normal household waste at the end of its life, but

hand it in at an ofcial collection point for recycling. By doing this, you help to preserve the

environment.

- Follow your country’s rules for the separate collection of electrical and electronic products. Correct disposal helps prevent negative consequences for the environment and human health.

Storage

1 Empty the water tank before you store the appliance (Fig. 24).

2 Make sure all parts are clean and dry before you store the appliance (see chapter ‘Cleaning

and maintenance’).

3 Store the appliance with the blade unit in the jar to prevent damage.

4 Do not place the lid on the jar and leave the lid of the lling opening open to avoid bacterial

growth.

Guarantee and support

If you need information or support, please visit www.philips.com/support or read the separate

worldwide guarantee leaet.

Technical specications

- Voltage/wattage: see type plate on the bottom of the appliance.

- Maximum capacity of water tank: 200ml.

- Maximum capacity of jar, liquids: 450ml.

- Protection: temperature-controlled heating system and safety lock.

Troubleshooting

This chapter summarises the most common problems you could encounter with the appliance. If you are unable to solve the problem with the information below, visit www.philips.com/support for a list of frequently asked questions or contact the Consumer Care Centre in your country.

Problem Possible cause Solution

The appliance does not work.

The steaming light does not go on.

The ingredients are not heated up completely.

The appliance does not steam.

Steaming takes too long or the steam function does not work at all.

Steam is coming

out of the lling

opening.

The appliance is equipped with a safety lock. If the parts have not been assembled properly onto the motor unit, the appliance does not work.

The appliance is not connected to the mains.

The jar is not placed on the motor unit properly.

You want to start a second steaming process just after one

has nished.

The pieces in the jar are too big, there is too much food in the jar or you have not steamed the food long enough.

You have not put water in the appliance.

You have not put the jar on the motor unit in the correct position.

There is too much scale in the water tank.

The lid of the lling

opening is not closed properly.

The steam outlet on the motor unit is blocked by food or by scale.

The steam hole in the lid is blocked.

Assemble all parts properly. See chapter ‘Using the appliance’.

Put the plug in the wall socket.

Place the jar on the motor unit properly.

Switch off the appliance and let it cool down for a few minutes before you start a second steaming process.

Cut the food into smaller pieces (2-3cm), decrease the amount of food in the jar or select a longer steaming time (max. 20 minutes). Check the recipe booklet and/or the table in chapter ‘Ingredients and steaming times’ to make sure that you select the correct steaming time for the ingredients you want to steam or the recipe you want to prepare.

Switch off the appliance and put the right amount of water in the appliance.

Place the jar on the appliance in the correct position (see section ‘Steaming’ in chapter ‘Using the appliance’).

Descale the water tank. See chapter ‘Cleaning and maintenance’, section ‘Descaling’.

Close the lid of the lling opening properly (‘click’).

Clean the steam outlet with a pointy object without damaging the seal and follow the descaling instructions in the future. See chapter ‘Cleaning and maintenance,’ section ‘Descaling’.

Remove the valve and clean the steam hole in the lid properly.

ENGLISH 15

ENGLISH16

Problem Possible cause Solution

The steaming light goes on again after the steaming

process is nished.

After some time, the appliance

buzzes again.

The blade unit or motor unit is blocked.

The motor unit gives off an unpleasant smell

during the rst

few times of use.

The appliance continues to give off an unpleasant smell after I used it a few times.

The appliance makes a lot of noise, produces an unpleasant smell, feels hot to the touch, emits smoke, etc.

The lid of the jar leaks.

There are white

spots on the lling

opening and/or on the jar, sieve and lid.

The appliance produces a lot of noise while it is blending.

You have accidentally left the jar on the base for more than 10 minutes without switching off the appliance.

There is too much food in the jar.

This is normal. If the appliance continues to give off this smell after

You put too much food in the jar or you let the appliance blend too long.

There is too much food in the jar.

You let the appliance operate too long without interruption.

You have not assembled the lid on the jar properly.

There is too much food in the jar.

Scale has built up on these parts.

The sieve is not attached to the lid of the jar.

Switch off the appliance within 10 minutes after the

steaming process is nished and then blend the

food or remove it from the jar.

Switch off the appliance and process a smaller

quantity. Do not ll the jar beyond the top edge of

the green blade unit.

you have used it a few times, check whether the processing quantity and processing time are correct. See chapter ‘Ingredients and steaming times’.

Process smaller quantities and do not let the appliance blend for more than 30 seconds at a time.

Switch off the appliance and process a smaller quantity.

Do not let the appliance blend for more than 30 seconds at a time.

Assemble the lid on the jar properly. See chapter ‘Using the appliance’.

Switch off the appliance and process a smaller quantity.

This is normal. Remove the scale periodically. See chapter ‘Cleaning and maintenance’, section ‘Descaling’.

Make sure that the sieve is attached to the lid of the jar.

Problem Possible cause Solution

The water in the water tank has an unusual colour when you pour it out of the water tank or when it enters the jar during steaming, or the water in the water tank has an unpleasant smell.

A smell of grilled or burnt food comes out of the water tank

There are dark spots in the baby food or the water in the jar has an unusual colour.

Food particles have entered the water tank during use.

Food particles have entered the water tank during use and have caked onto the heating element.

Food particles have entered the water tank during use and have caked onto the heating element. This causes residues of these food particles to enter the jar during steaming.

Clean the water tank according to the instructions in chapter ‘Cleaning and maintenance, section ‘Cleaning the water tank’. Use the appliance strictly according to the instructions. Make sure you do not

overll the water tank with water (max 200ml) and that you do not overll the jar with food (do not ll

the jar beyond the top edge of the green blade unit). Do not steam the same ingredients for more than 20 minutes and do not put water for steaming directly in the jar. Also make sure that the valve is

xed in the lid.

overll the water tank with water (max 200ml) and that you do not overll the jar with food (do not ll

xed in the lid.

overll the water tank with water (max 200ml) and that you do not overll the jar with food (do not ll

xed in the lid.

ENGLISH 17

+ 35 hidden pages