Philips SB365B/37 User manual

Always there to help you

Question?

Contact

Philips

Register your product and get support at

www.philips.com/support

SB365B

User manual

Contents

1 Important 2

Safety 2

2 Your Bluetooth speaker 3

Introduction 3
What's in the box 3
Overview of the speaker 4

3 Get started 5

Power supply 5
Turn on 5

4 Play from Bluetooth-enabled devices 6

Connect a device 6
Play from Bluetooth device 7
Disconnect the Bluetooth-enabled device 7
Connect another Bluetooth-enabled
device 7
Reconnect the Bluetooth device 7

5 Other features 8

Charge your mobile devices 8
Listen to an external device 8
Adjust volume 8

6 Product information 9

Specications 9

7 Troubleshooting 10

General 10
About Bluetooth device 10

8 Notice 11

1EN

1 Important

Safety

Warning

• Never remove the casing of this speaker.

• Never lubricate any part of this speaker.

• Never place this speaker on other electrical equipment.

• Keep this speaker away from direct sunlight, naked

amesorheat.

Important safety instructions

a Read these instructions.
b Keep these instructions.
c Heed all warnings.
d Follow all instructions.
e Do not use this apparatus near water.
f Clean only with dry cloth.
g Do not block any ventilation openings.

Install in accordance with the
manufacturer's instructions.

h Do not install near any heat sources such

as radiators, heat registers, stoves, or

other apparatus (including ampliers) that

produce heat.

i Protect the power cord from being

walked on or pinched, particularly at
plugs, convenience receptacles, and the
point where they exit from the apparatus.

j Only use attachments/accessories

specied by the manufacturer.

k Unplug this apparatus during lightning

storms or when unused for long periods
of time.

l Refer all servicing to qualied service

personnel. Servicing is required when
the apparatus has been damaged in any
way, such as liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.

m Battery shall not be exposed to excessive

heat such as sunshine, re or the like.

n Apparatus shall not be exposed to

dripping or splashing.

o Do not place any sources of danger on

the apparatus (e.g. liquid lled objects,
lighted candles).

p Where the plug of the Direct Plug-in

Adapter is used as the disconnect device,
the disconnect device shall remain readily
operable.

Note

• The type plate is located on the bottom of the

apparatus.

2 EN

2 Your Bluetooth

speaker

Congratulations on your purchase, and

welcometoPhilips!Tofullybenetfromthe

support that Philips offers, register your product
at www.philips.com/welcome.

Introduction

With this product, you can

• play audio from Bluetooth-enabled devices,
or other external devices;

• charge your mobile devices.

What's in the box

Check and identify the contents of your
package:

• Speaker

• Power adaptor

• Audio-in cable

• Short user manual

3EN

Overview of the speaker

c

d

f

e

b

a
d

g

a NFC

• Connect a NFC compatible device

through Bluetooth.

b

• Bluetooth indicator.

c

• Turn on the speaker or switch to

standby mode.

• Disconnect the paired device.

• Enter Bluetooth pairing mode.

4 EN

d - VOL/VOL +

• Adjust volume.

e CHARGING

• Charge your mobile devices.

f AUDIO IN

• Connect an external audio device.

g DC IN

• Connect power.

3 Get started

Always follow the instructions in this chapter in
sequence.

Power supply

Either AC power or battery can be used as
power supply of this product.

Connect the power adaptor to:

• the DC IN socket at the back of the
speaker.

• the wall outlet.

Option 1: Battery power

The speaker can operate on the built-in
rechargeable battery.

Note

• Rechargeable battery has a limited number of charge

cycles. Battery life and number of charge cycles vary by
use and settings.

• It takes approximately 5 hours to fully charge the

battery.

• When battery is low or under charging, the button

asheswhite.

To recharge the built-in battery:

Connect the speaker to AC power supply.

Option 2: AC power

Caution

• Risk of product damage! Make sure that the power

voltage corresponds to the voltage printed on the back
or underside of the speaker.

• Risk of electric shock! When you unplug the AC

adapter, always pull the plug from the socket. Never
pull the cord.

Turn on

Press .

» The speaker switches to Bluetooth

mode.

» TheBluetoothindicatorbeginstoash.

Switch to standby mode

Press again.

» The speaker switches to standby

mode.

Note

• When there is no valid connection with other devices

and music playback for 15 minutes, the speaker
switches to standby automatically for power saving.

5EN

4 Play from

Bluetooth­enabled devices

With this product, you can listen to audio from
Bluetooth-enabled devices.

Connect a device

Note

• The speaker can memorize a maximum of four paired

devices.Thefthpaireddevicewillreplacetherstone.

• Make sure that Bluetooth function is enabled on your

device, and your device is set as visible to all other
Bluetooth devices.

• Any obstacle between this speaker and a Bluetooth

device can reduce the operational range.

• Keep away from any other electronic device that may

cause interference.

• The operational range between this speaker and a

Bluetooth device is approximately 10 meters (30 feet).

• Make sure that no audio input cable is connected to

the AUDIO IN socket.

Option 1: Connect a device through NFC

Near Field Communication (NFC) is a
technology that enables short-range wireless
communication between various NFC
compatible devices, such as mobile phones and
IC tags.
If your Bluetooth device supports NFC, you can
connect it with this speaker easily.

1 Press to turn on the speaker.

» The Bluetooth indicator begins to

ash.

2 Enable the NFC feature on your Bluetooth

device (see the user manual of the device
for details).

3 Tap the NFC tag on the speaker with the

NFC area of your Bluetooth device.

4 On your Bluetooth device, accept the

pairing request with "SB365B". If necessary,
input "0000" as the pairing password.

5 Follow the on-screen instructions to

complete the pairing and connection.

» After successful pairing and connection,

the speaker beeps twice, and the
Bluetooth indicator turns solid blue.

Option 2: Connect a device manually

1 Press to turn on the speaker.

» The Bluetooth indicator begins to

ash.

2 On your Bluetooth device, enable

Bluetooth and search for Bluetooth devices
(refer to the user manual of the device).

3 When [Philips SB365B] is displayed on

your device, select it to start pairing and
connection. If necessary, enter default
password “0000”.

» After successful pairing and connection,

the speaker beeps twice, and the
Bluetooth indicator turns solid blue.

• If you fail to find [Philips SB365B]
for pairing, press and hold for two
seconds to enter pairing mode.

6 EN

Bluetooth indicator
( )

Flashing blue Connecting or waiting

Solid blue Connected

Description

for connection

Play from Bluetooth device

After successful Bluetooth connection, play
audio on the Bluetooth device.

» Audio streams from your Bluetooth

device to the speaker.

Disconnect the Bluetooth­enabled device

• Press and hold for two seconds;

• Disable Bluetooth on your device; or

• Move the device beyond the
communication range.

» TheBluetoothindicatorashes.

Connect another Bluetooth­enabled device

1 Press and hold for two seconds to enter

pairing mode.

2 Connect another device.

Reconnect the Bluetooth device

• Next time when you turn on the speaker,
it will reconnect the last connected device
automatically; or

• On your Bluetooth device, select "Philips
SB365B" on your Bluetooth menu to start
connection.

7EN

5 Other features

Charge your mobile devices

With this speaker, you can charge your mobile
devices through the CHARGING socket.

Note

• The USB socket is used for charging only.

• If the speaker is powered by the built-in battery or in

standby mode, you cannot charge your mobile devices.

• Connect to your mobile device with a USB
cable (not supplied).

» Once the device is recognized, the

charging starts.

CHARGING

Listen to an external device

With this speaker, you can also listen to an
external audio device such as an MP3 player.

Note

• Make sure that music playback through Bluetooth is

stopped.

1 Connect the supplied audio input cable to

• the AUDIO IN socket on this speaker,
and

• the headphone socket on the external
device.

2 Play audio on the external device (refer to

its user manual).

Adjust volume

During play, press VOL + or - VOL to increase
or decrease volume.

Tip

• When the volume reaches the maximum or minimum,

the white LED indicator on the buttonashesfor
one second.

8 EN

6 Product

information

Note

• Product information is subject to change without prior

notice.

Specications

Amplier

Rated Output Power 2 X 4 W RMS
Signal to Noise Ratio > 65 dBA
AUX Input 800 mV

Bluetooth

Bluetooth version V4.0
Supportedproles A2DP, AVRCP
Range 10 m (Free space)

General information

Power Supply

- AC Power (power
adapter)

- Built-in Battery 7.4 V, 2200 mAh
Charging Voltage and

Current
Operation Power

Consumption
Standby Power

Consumption
Dimensions - Main

Unit (W x H x D)
Weight - Main Unit 0.5 kg

Brand name: PHILIPS;

Model: TPA103B­15090-US;

Input: 100-240 V~,
50/60 Hz, 1.1A MAX

Output: 9 V 1.66 A;

5 V 500 mA

4 W

<0.5 W

201 x 101 x 35 mm

9EN

7 Troubleshooting

About Bluetooth device

Warning

• Never remove the casing of this device.

To keep the warranty valid, never try to repair
the system yourself.
If you encounter problems when using this
device, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips Web page (www.
philips.com/support). When you contact Philips,
make sure that the device is nearby and the
model number and serial number are available.

General

No power

• Make sure that the AC power plug of the
unit is connected properly.

• Make sure that there is power at the AC
outlet.

• Recharge your speaker.

No sound

• Adjust volume on the speaker or the
Bluetooth-connected device.

• Make sure that your Bluetooth device is
within the effective operational range.

No response from the speaker

• Restart the speaker.

• Make sure that AC power is connected
properly.

• Make sure that there is power at the AC
outlet.

The audio quality is poor after connection
with a Bluetooth-enabled device.

• The Bluetooth reception is poor. Move the
device closer to this product or remove
any obstacle between them.

Cannot connect with the device.

• The Bluetooth function of the device is not
enabled. Refer to the user manual of the
device for how to enable the function.

• This product is already connected with
another Bluetooth-enabled device.
Disconnect that device and then try again.

The paired device connects and disconnects
constantly.

• The Bluetooth reception is poor. Move the
device closer to this product or remove
any obstacle between them.

• For some devices, Bluetooth connection
may be deactivated automatically as a
power-saving feature. This does not indicate
any malfunction of this product.

10 EN

8 Notice

Anychangesormodicationsmadetothis

device that are not expressly approved by
Gibson Innovations may void the user’s
authority to operate the equipment.

Notice for the USA and Canada

This device complies with Part 15 of the FCC
Rules and license-exempt RSS standard of
Industry Canada. Operation is subject to the
following two conditions:

1 this device may not cause harmful

interference, and

2 this device must accept any interference

received, including interference that may
cause undesired operation.

This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses, and can radiate radio frequency energy
and, if not installed and used in accordance
with the instruction manual, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception,
which can be determined by turning the
equipment off and on, the user is encouraged
to try to correct the interference by one or
more of the following measures:

• Relocate the receiving antenna.

• Increase the separation between
equipment and receiver.

• Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.

• Consult the dealer or an experienced
radio/TV technician for help.

RF Radiation Exposure Statement: This
equipment complies with FCC’s and IC’s RF
radiation exposure limits set forth for an
uncontrolled environment. The antenna(s)
used for this transmitter must be installed and
operated to provide a separation distance of
at least 20 cm from all persons and must not
be collocated or operating in conjunction with
any other antenna or transmitter. Installers must
ensure that 20cm separation distance will be
maintained between the device (excluding its
handset) and users.

CAN ICES-3(B)/NMB-3(B)

Disposal of your old product and battery

Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
This product may contain lead and mercury.
Disposal of these materials may be regulated
due to environmental considerations. For
disposal or recycling information, please contact
your local authorities or visit www.recycle.
philips.com.
This product contains non-removable batteries:

• Do not incinerate. Batteries may explode if
overheated.

• For disposal or recycling information,
please contact your local authorities or visit
www.recycle.philips.com.

Caution

• Removal of the built-in battery invalidates the warranty

and may destroy the product.

11EN

Always bring your product to a professional to
remove the built-in battery.

Environmental information

All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.

The Bluetooth word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by Gibson
is under license. Other trademarks and trade
names are those of their respective owners.

The N Mark is a trademark or registered
trademark of NFC Forum, Inc. in the United
States and in other countries.

12 EN

13

2015 © Gibson Innovations Limited. All rights reserved.
This product has been manufactured by, and is sold under the responsibility of Gibson
Innovations Ltd., and Gibson Innovations Ltd. is the warrantor in relation to this product.
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V.
and are used under license from Koninklijke Philips N.V.

SB365B_UM_37_V1.0