Philips saa4970t DATASHEETS

INTEGRATED CIRCUITS

DATA SH EET

SAA4970T

Economical video processing IC
(ECOBENDIC)

Preliminary specification
File under Integrated Circuits, IC02

1996 Oct 25

Philips Semiconductors Preliminary specification

Economical video processing IC

SAA4970T

(ECOBENDIC)

FEATURES

• Digital horizontal PLL

• Digital CTI (DCTI)

• Digital luminance peaking

• Digital phase compensation filter

• D/A conversion

• Simple multi picture processing

• Coloured frame generation

• Memory/sync processing.

QUICK REFERENCE DATA

SYMBOL PARAMETER MIN. MAX. UNIT

V

DD

V

CC

T

amb

digital supply voltage 4.5 5.5 V
analog supply voltage 4.75 5.25 V
operating ambient temperature 0 70 °C

GENERAL DESCRIPTION

The ECOBENDIC is an economical video processing IC
(Economical Back End IC) for double scan conversion.
It consists of sync/memory control, video enhancing
features and D/A conversion. The IC is designed to
cooperate with an 83C654 type of microcontroller,
Texas Instruments TMS4C2970/2971 memories plus a
4:1:1 A/D converter TDA8755/8753A.

ORDERING INFORMATION

TYPE NUMBER

NAME DESCRIPTION VERSION

SAA4970T VSO56 plastic very small outline package; 56 leads SOT190-1

PACKAGE

1996 Oct 25 2

Philips Semiconductors Preliminary specification

Economical video processing IC
(ECOBENDIC)

BLOCK DIAGRAM

handbook, full pagewidth

47 to

UVIN3

to UVIN0

YIN7

to YIN0

HA, V

Xtal

Xtal

A

O

I

50

37 to 41,
44 to 46

22, 23

55

56

REFORMATTER

UP-SAMPLING

4

PHASE COMPENSATION

PLL

53

FILTER

51

8

2

CK1 CK2 ALE

SAA4970T

MICROCONTROLLER

INTERFACE

8

29 to 36

parallel bus
AD7 to AD0

address line

microcontroller

DCTI

24 27 28

RDN CLMP IE, WE, REmicrocontroller

WRN

command

PEAKING

8

8

9

SYNC PROCESSING
MEMORY CONTROL

14

D

D

D

3

A

A

A

15 to 17

SAA4970T

3

U

O

5

V

O

7

Y

O

19

H

D

18

V

D

MGE092

microcontroller parallel bits

Fig.1 Block diagram.

1996 Oct 25 3

Philips Semiconductors Preliminary specification

Economical video processing IC

SAA4970T

(ECOBENDIC)

PINNING

SYMBOL PIN TYPE DESCRIPTION

TEST2 1 input test control
P

mirref

U

O

V

SSA

V

O

V

CC

Y

O

V

ref

I

ref

V

refH

R1 11 I/O reset acquisition horizontal counter
R2 12 I/O reset display horizontal counter
PIP 13 input PIP related input 0
CLMP 14 output clamping control
IE 15 output field memory input enable
WE 16 output field memory write enable
RE 17 output field memory read enable
V

D

H

D

RESET 20 output watchdog output (microcontroller reset)
BONE 21 input watchdog input (microcontroller bone)
H

A

V

A

ALE 24 input address latch enable
IT1 25 output acquisition related interrupt
IT2 26 output display related interrupt
WRN 27 input write not pulse
RDN 28 input read not pulse
AD7 29 I/O programmable signal positioner (psp) data bus bit 7 (MSB)
AD6 30 I/O psp data bus bit 6
AD5 31 I/O psp data bus bit 5
AD4 32 I/O psp data bus bit 4
AD3 33 I/O psp data bus bit 3
AD2 34 I/O psp data bus bit 2
AD1 35 I/O psp data bus bit 1
AD0 36 I/O psp data bus bit 0 (LSB)
YIN7 37 input Y input bus bit 7 (MSB)
YIN6 38 input Y input bus bit 6
YIN5 39 input Y input bus bit 5
YIN4 40 input Y input bus bit 4

2 input decoupling P-mirror reference
3 output analog U output
4 ground analog ground (0 V)
5 output analog V output
6 supply analog supply voltage (+5 V)
7 output analog Y output
8 supply analog supply voltage reference D/A ladder HIGH
9 supply reference current

10 supply D/A decoupling capacitor

18 I/O display vertical pulse
19 output display horizontal pulse

22 I/O acquisition horizontal pulse
23 I/O acquisition vertical pulse

1996 Oct 25 4

Philips Semiconductors Preliminary specification

Economical video processing IC
(ECOBENDIC)

SYMBOL PIN TYPE DESCRIPTION

YIN3 41 input Y input bus bit 3
V

DD

V

SS

YIN2 44 input Y input bus bit 2
YIN1 45 input Y input bus bit 1
YIN0 46 input Y input bus bit 0 (LSB)
UVIN3 47 input UV input bus bit 3 (MSB)
UVIN2 48 input UV input bus bit 2
UVIN1 49 input UV input bus bit 1
UVIN0 50 input UV input bus bit 0 (LSB)
CK2 51 I/O display clock
V

SS

CK1 53 I/O acquisition clock
TEST1 54 input test control
Xtal

O

Xtal

I

42 supply digital supply voltage (+5 V)
43 ground digital ground (0 V)

52 ground digital ground (0 V)

55 output external crystal output (12 MHz)
56 input PLL crystal input (12 MHz)

SAA4970T

1996 Oct 25 5

Philips Semiconductors Preliminary specification

Economical video processing IC
(ECOBENDIC)

handbook, halfpage

TEST2

P

mirref

U

V

SSA

V

V

CC
Y

V

ref

I

ref

V

refH

R1
R2

PIP

CLMP

WE

RE
V

H

RESET

BONE

H
V

ALE

IT1
IT2

WRN

RDN

O

O

O

IE

D
D

A
A

1
2
3
4
5
6
7
8

9
10
11
12
13
14

SAA4970T

15
16
17
18
19
20
21
22
23
24
25
26
27
28

MGE091

Xtal

56

I

Xtal

55

O

TEST1

54

CK1

53

V

52

SS

CK2

51

UVIN0

50

UVIN1

49

UVIN2

48

UVIN3

47

YIN0

46

YIN1

45

YIN2

44

V

43

SS

V

42

DD

YIN3

41

YIN4

40

YIN5

39

YIN6

38

YIN7

37

AD0

36

AD1

35

AD2

34

AD3

33

AD4

32

AD5

31

AD6

30

AD7

29

SAA4970T

FUNCTIONAL DESCRIPTION
ECO data path

The data path performs the DCTI, peaking, phase
compensation, framing and blanking functions plus colour
reformatting and variable delay of Y to UV at the input and
output of the data path.

DCTI
DCTI is implemented to get a dynamic interpolation of the

low bandwidth U and V signals. First a 2 : 1 linear
interpolation is done, to go from a 4 :1:1 format to a
4:2:2 format. A second interpolation is done in which the
data path delay is varied on the basis of a function of the
second derivative of the U and V signal (or more precise:

d

dUtddV

+{}

td

td

first half the data path delay is higher than nominal and in
the second half it is lower than nominal. This will make the
edge much steeper. As this second interpolation is done
with the resolution equal to that of the Y samples and also
with a zero DCTI gain a 2 : 1 interpolation is performed, a
4:4:4 format is obtained.

The DCTI function can be controlled by setting the range
to ±12, ±8, ±6 or ±4 pixels (see Fig.3) or by adjusting the

gain to 0,
An artefact of this processing exists when two edges are

close together in the video. During the second half of the
first edge a delay is chosen that will collect video data
where the second edge is already active. The same is valid
for the second edge. The result of this processing on a
video pulse, which is looking like a hill, is that of a hill with
one or two bumps in it. To prevent this from happening, the
positions where the first derivatives in U and V change
sign, are marked and used to limit the range of the relative
delay. This function is called ‘over the hill protection’. It can
be turned on and off. Figures 5 and 6 show the effect of
the DCTI function with and without ‘over the hill protection’
when applied to a hill-shaped video pulse.

). The effect at an edge is that during the

1

⁄4,1⁄2 or 1.

Fig.2 Pin configuration.

1996 Oct 25 6

Philips Semiconductors Preliminary specification

Economical video processing IC
(ECOBENDIC)

120

handbook, full pagewidth

digital
signal

amplitude

100

80

60

110

(1) input signal.
(2) range = 4.
(3) range = 12.

(1)

SAA4970T

MGE093

(2)

(3)

20

40 45352515530

samples

Gain =1⁄2.

120

handbook, full pagewidth

digital
signal

amplitude

100

80

60

110

(1) input signal.
(2) gain = 0.25.

Fig.3 DCTI with variation of k range.

(1)

(2)

(3)

(4)

20

(3) gain = 0.5.
(4) gain = 1.

Range = 12.

MGE094

40 45352515530

samples

1996 Oct 25 7

Fig.4 DCTI with variation of k gain.

Philips Semiconductors Preliminary specification

Economical video processing IC
(ECOBENDIC)

120

handbook, full pagewidth

digital
signal

amplitude

100

(1) output.
(2) input.

80

60

20 30 90

(2)

(1)

5040

807060

Gain =1⁄2.
Range = ±12.
Hill protection = on.

SAA4970T

MGE095

samples

120

handbook, full pagewidth

digital
signal

amplitude

100

80

60

20 30 90

(1) output.
(2) input.

Fig.5 DCTI with ‘over the hill protection’.

(1)

(2)

5040

807060

Gain =1⁄2.
Range = ±12.
Hill protection = off.

MGE096

samples

1996 Oct 25 8

Fig.6 DCTI without ‘over the hill protection’.

Philips Semiconductors Preliminary specification

Economical video processing IC
(ECOBENDIC)

PEAKING
Peaking is implemented to obtain a higher gain in the

middle and upper ranges of the luminance bandwidth.
The filtering is an addition of:

• the original signal

• the original signal band-passed with centre

frequency =1⁄4f

• the original signal high-passed with maximum gain at
frequency =1⁄2fs.

12

handbook, halfpage

10

IH_PeakingI

(dB)

s

MGE097

(1)

8

(2)

6

(3)

SAA4970T

The band-passed and high-passed signals are weighted
with factors 0,
becomes [−α, −β, 1 + 2α +2β,−β, −α], where α is the
band-pass weighting factor and β the high-pass weighting
factor.

Coring is added to obtain no gain for low amplitudes in the
(high-pass + band-pass) signal, which is then considered
to be noise. Coring levels can be programmed as 0 (off),
+1/−2, +3/−4 and +7/−8 LSB at 10-bit word.

A limiter brings back the 11-bit range to a 9-bit range with
a clipping function on the lower and upper side.

handbook, halfpage

IH_PeakingI

(dB)

1

⁄8,1⁄4 and1⁄2. The impulse response

12

10

8

6

(1)

(2)
(3)

(4)

MGE098

(1) β =1⁄2.
(2) β =1⁄4.
(3) β =1⁄8.
(4) β =0.

4

2

0

0



1/4f

(4)

s

1/2f

Fig.7 Peaking transfer function with variation of β

(α =1⁄8).

4

2

0

0

s

(1) β =1⁄2.
(2) β =1⁄4.
(3) β =1⁄8.
(4) β =0.



1/4f

s

1/2f

s

Fig.8 Peaking transfer function with variation of β

(α =1⁄4).

1996 Oct 25 9