INTEGRATED CIRCUITS
SA576
Low power compandor
Product specification |
1997 Aug 14 |
IC17 Data Handbook
m n r
Philips Semiconductors |
Product specification |
|
|
|
|
|
|
|
Low power compandor |
SA576 |
|
|
|
|
|
|
|
The SA576 is a unity gain level programmable compandor designed for low power applications. The SA576 is internally configured as an expandor and a compressor to minimize external component count.
The SA576 can operate at 1.8V. During normal operations, the
SA576 can operate from at least a 2V battery. If the battery voltage drops to 1.8V, this part will still continue to function, however, turning on the part at a VCC of 1.8V requires two external resistors to bring
VREF to half VCC. One resistor connects between VCC and VREF; the other connects from VREF to ground. A typical value for these
external resistors is approximately 20k. A lower value can be used, but the power consumption will go up.
The SA576 is available in a 14-pin plastic DIP and SO packages.
D and N Packages
|
|
|
|
|
|
|
GCELLIN |
1 |
|
|
|
14 |
VCC |
|
|
|
|
|
|
|
RECTIN |
2 |
|
|
|
13 |
COMPCAP2 |
|
|
|
|
|
|
|
EXPCAP |
3 |
|
|
|
12 |
COMPIN |
|
|
|
|
|
||
EXPOUT |
4 |
|
|
|
11 |
COMPCAP1 |
|
|
|
|
|
|
|
VREF |
5 |
|
|
|
10 |
RECTIN |
|
|
|
|
|
||
I |
6 |
|
|
|
9 |
GCELLIN |
REF |
|
|
|
|
|
|
|
|
|
|
|
|
|
GND |
7 |
|
|
|
8 |
COMPOUT |
|
|
|
|
|
|
|
SR00713
FEATURES |
Figure 1. Pin Configuration |
|
•Operating voltage range: 1.8V to 7V |
|
|
•Low power consumption |
APPLICATIONS |
|
(1.4mA @ 3.6V) |
||
•Cordless telephone |
||
•Over 80dB of dynamic range |
||
•Consumer audio |
||
•Wide input/output swing capability |
||
•Wireless microphones |
||
(rail-to-rail) |
||
•Low external component count |
• |
|
|
Modems |
|
•ESD hardened |
• |
|
|
Electric organs |
|
|
•Hearing aids |
|
|
•Automatic level control |
DESCRIPTION |
TEMPERATURE RANGE |
ORDER CODE |
DWG # |
|
|
|
|
14-Pin Plastic Dual In-Line Package (DIP) |
±40 to +85°C |
SA576N |
SOT27-1 |
|
|
|
|
14-Pin Plastic Small Outline (SO) |
±40 to +85°C |
SA576D |
SOT108-1 |
|
|
|
|
SYMBOL |
|
PARAMETER |
RATING |
UNITS |
|
|
|||
|
SA576 |
|||
|
|
|
|
|
|
|
|
|
|
VCC |
Supply voltage |
|
8 |
V |
TA |
Operating ambient temperature range |
±40 to +85 |
°C |
|
TSTG |
Storage temperature range |
|
±65 to +150 |
°C |
θJA |
Thermal impedance |
DIP |
90 |
°C/W |
|
SO |
125 |
°C/W |
1997 Aug 14 |
10±2 |
853-1536 18287 |
Philips Semiconductors |
Product specification |
|
|
|
|
Low power compandor |
SA576 |
|
|
|
|
|
|
|
|
|
|
|
10k |
|
|
|
|
|
|
|
|
|
EXPIN |
C1 |
|
|
GAINCELL |
|
|
|
|
|
|
|
|
|
|
|
|
10k |
|
|
|
|
|
|
|
|
||
|
|
+ |
|
1 |
|
|
|
|
|
14 |
|
VCC |
||
|
|
|
|
G |
|
|
|
|
|
|
||||
|
|
10μF |
|
Σ |
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
R1* |
|
RECTIFIER |
10k |
|
|
|
|
|
COMPCAP2 |
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
5k |
|
|
|
|
13 |
||
|
|
|
|
RECTIN |
2 |
|
|
|
|
|
|
+ |
C8 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2.2μF |
|
|
EXPCAP |
|
|
|
|
|
30k |
30k |
|
|
10k |
C7 |
|
|
|
|
|
|
|
|
|
|
+ |
|
|||||
C2 |
+ |
2.2μF |
|
|
3 |
|
|
|
|
|
|
12 |
|
COMPIN |
|
|
|
|
|
|
|
|
|
|
|
10μF |
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
C3 |
|
EXPANDOR |
|
|
|
|
|
COMPCAP1 |
||
|
|
|
|
+ |
|
|
|
|
|
|
|
11 |
||
|
|
EXPOUT |
|
4 |
|
|
|
Σ |
|
|
|
+ C6 |
||
|
|
10μF |
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
10k |
RECTIFIER |
|
2.2μF |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
VREF |
C4 |
+ |
|
|
|
|
8.6k |
|
|
|
|
|
|
|
|
5 |
|
|
|
|
|
10 |
RECTIN |
||||
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
10μF |
|
|
VREF |
|
|
|
|
|
R3* |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
BANDGAP |
|
|
|
|
10k |
|
|
|
|
|
|
|
6 |
|
|
|
|
|
9 |
GCELLIN |
||
|
|
|
|
R2* |
IREF |
VCC |
COMPRESSOR |
|
G |
|||||
|
|
|
|
|
|
|
|
+ C5 |
|
|||||
|
|
|
|
|
|
GND |
|
|
|
GAINCELL |
|
|||
|
|
|
|
|
|
|
|
|
|
10μF |
|
|||
|
|
|
|
|
7 |
|
|
|
|
|
|
8 |
+ |
COMPOUT |
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
C9 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
10μF |
|
|
|
|
GND |
|
|
|
|
|
|
|
|
|
|
*R1, R2 and R3 are 1% resistors. |
|
|
|
|
|
|
|
|
|
SR00714 |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Figure 2. Block Diagram and Test and Application Circuit
TA = 25°C, VCC = 3.6VDC, compandor 0dB level = ±20dBV = 100mVRMS, output load RL = 10kΩ, Freq = 1kHz, unless otherwise specified. R1, R2 and R3 are 1% resistors.
|
|
|
|
|
|
LIMITS |
|
|
|
|
|
|
|
|
|
||
SYMBOL |
PARAMETER |
TEST CONDITIONS |
|
SA576 |
|
UNITS |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
MIN |
TYP |
MAX |
|
|
|
|
|
|
|
|
|
|
VCC |
Supply voltage1 |
|
|
|
2 |
3.6 |
7 |
V |
ICC |
Supply current |
No signal |
|
1.4 |
3 |
mA |
||
R2 = 100kΩ |
|
|||||||
|
|
|
|
|
|
|||
V |
Reference voltage2 |
V |
CC |
= 3.6V |
|
1.8 |
|
V |
REF |
|
|
|
|
|
|
|
|
RL |
Summing amp output load |
|
|
|
10 |
|
|
kΩ |
THD |
Total harmonic distortion |
1kHz, 0dB, BW = 3.5kHz |
|
0.25 |
1.5 |
% |
||
|
|
|
|
|
|
|
||
ENO |
Expandor output noise voltage |
BW = 20kHz, RS = 0Ω |
|
10 |
30 |
μV |
||
0dB |
Unity gain level |
0dB at 1kHz |
±1.5 |
0.18 |
1.5 |
dB |
||
|
|
|
|
|
|
|
||
VOS |
Output voltage offset |
No signal |
±150 |
1 |
150 |
mV |
||
|
Expandor output DC shift |
No signal to 0dB |
±100 |
7 |
100 |
mV |
||
|
|
|
|
|
|
|
||
|
Tracking error relative to 0dB output |
-20dB expandor |
±1.0 |
0.3 |
1.0 |
dB |
||
|
|
|
|
|
|
|
||
|
Crosstalk, COMP to EXP |
1kHz, 0dB, CREF = 10μF |
|
±80 |
|
dB |
||
VO |
Output swing low |
|
|
|
|
0.2 |
|
V |
|
|
|
|
|
|
|
||
Output swing high |
|
|
|
|
VCC ± 0.2 |
|
||
|
|
|
|
|
|
|
NOTE:
1.Operation down to VCC = 1.8V is possible, see description on front page of SA576 data sheet.
2.Reference voltage, VREF, is typically at 1/2 VCC.
1997 Aug 14 |
10±3 |