Philips PIP 3206 R Service Manual
www.DataSheet4U.com
Philips Semiconductors Preliminary specification
TOPFET high side switch PIP3206-R
SMD version
DESCRIPTION QUICK REFERENCE DATA
Monolithic single channel high side SYMBOL PARAMETER MAX. UNIT protected power switch in TOPFET2 technology assembled in V a 5 pin plastic surface mount package. I
BG
L
Continuous off-state supply voltage 50 V
Continuous load current 10 A
APPLICATIONS T
General controller for driving R
lamps, motors, solenoids, heaters.
j
ON
Continuous junction temperature 150 ˚C
On-state resistance Tj = 25˚C 14 mΩ
FEATURES FUNCTIONAL BLOCK DIAGRAM
Vertical power TrenchMOS
Low on-state resistance
CMOS logic compatible
Very low quiescent current
Latched overtemperature
protection
Load current limiting
at reduced level
Short circuit load detection
Overvoltage and undervoltage
shutdown with hysteresis
Diagnostic status indication
Voltage clamping for turn off
of inductive loads
ESD protection on all pins
Reverse battery, overvoltage
and transient protection
STATUS
INPUT
GROUND
CONTROL &
PROTECTION
CIRCUITS
RG
Fig.1. Elements of the TOPFET HSS with internal ground resistor.
BATT
POWER
MOSFET
LOAD
PINNING - SOT426 PIN CONFIGURATION SYMBOL
PIN DESCRIPTION
1 Ground
2 Input
3 (connected to mb)
4 Status
5 Load
3
12 45
mb Battery
October 2001 1 Rev 1.000
mb
B
I
TOPFET
HSS
S
Fig. 2. Fig. 3.
G
L
Philips Semiconductors Preliminary specification
TOPFET high side switch PIP3206-R
SMD version
LIMITING VALUES
Limiting values in accordance with the Absolute Maximum System (IEC 134)
SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT
V
BG
I
L
P
D
T
stg
T
j
T
sold
-V
BG
-V
BG
RI, R
II, I
S
II, I
S
E
BL
Continuous off-state supply voltage 0 50 V
Continuous load current T
Total power dissipation T
140˚C - 10 A
mb ≤
25˚C - 115 W
mb ≤
Storage temperature -55 175 ˚C
Continuous junction temperature
1
- 150 ˚C
Mounting base temperature during soldering - 260 ˚C
Reverse battery voltages
2
Continuous reverse voltage - 16 V
Peak reverse voltage - 32 V
Application information
S
External resistors
3
to limit input, status currents 3.2 - kΩ
Input and status
Continuous currents -5 5 mA
Repetitive peak currents δ ≤ 0.1, tp = 300 µs -50 50 mA
Inductive load clamping IL = 10 A, VBG = 16 V
Non-repetitive clamping energy Tj = 150˚C prior to turn-off - 460 mJ
ESD LIMITING VALUE
SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT
V
C
Electrostatic discharge capacitor Human body model; - 2 kV
voltage C = 250 pF; R = 1.5 kΩ
THERMAL CHARACTERISTICS
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
Thermal resistance
R
th j-mb
1 For normal continuous operation. A higher Tj is allowed as an overload condition but at the threshold T
2 Reverse battery voltage is allowed only with external resistors to limit the input and status currents to a safe value. The connected load must
3 To limit currents during reverse battery and transient overvoltages (positive or negative).
4 Of the output power MOS transistor.
Junction to mounting base - - 0.86 1.08 K/W
to protect the switch.
limit the reverse load current. The internal ground resistor limits the reverse battery ground current. Power is dissipated and the T
rating must be observed.
4
the over temperature trip operates
j(TO)
j
October 2001 2 Rev 1.000
Philips Semiconductors Preliminary specification
TOPFET high side switch PIP3206-R
SMD version
STATIC CHARACTERISTICS
Limits are at -40˚C ≤ Tmb ≤ 150˚C and typicals at Tmb = 25˚C unless otherwise stated.
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
Clamping voltages
V
V
-V
-V
V
I
I
I
I
BG
BL
LG
LG
BG
B
L
G
L
Battery to ground IG = 1 mA 50 55 65 V
Battery to load IL = IG = 1 mA 50 55 65 V
Negative load to ground IL = 10 mA 18 23 28 V
Negative load voltage
1
IL = 20 A; tp = 300 µs202530V
Supply voltage battery to ground
Operating range
2
5.5 - 35 V
Currents 9 V ≤ VBG ≤ 16 V
Quiescent current
3
VLG = 0 V - - 20 µA
Tmb = 25˚C - 0.1 2 µA
Off-state load current
4
VBL = V
BG
--20µA
Tmb = 25˚C - 0.1 1 µA
Operating current
Nominal load current
Resistances V
5
6
IL = 0 A - 2 4 mA
VBL = 0.5 V Tmb = 85˚C - - - A
BG
I
L
7
t
p
T
mb
R
ON
On-state resistance 9 to 35 V 5 A 300 µs 25˚C - 10 14 mΩ
150˚C - - 25 mΩ
R
ON
On-state resistance 6 V 5 A 300 µs 25˚C - 13 18 mΩ
150˚C - - 33 mΩ
R
G
1 For a high side switch, the load pin voltage goes negative with respect to ground during the turn-off of an inductive load.
2 On-state resistance is increased if the supply voltage is less than 9 V.
3 This is the continuous current drawn from the supply when the input is low and includes leakage current to the load.
4 The measured current is in the load pin only.
5 This is the continuous current drawn from the supply with no load connected, but with the input high.
6 Defined as in ISO 10483-1. Because of current limiting, this parameter is not applicable.
7 The supply and input voltage for the RON tests are continuous. The specified pulse duration tp refers only to the applied load current.
Internal ground resistance IG = 10 mA 95 150 190 Ω
October 2001 3 Rev 1.000
Loading...