Philips pcd5041 DATASHEETS

INTEGRATED CIRCUITS

DATA SH EET

PCD5041

DECT burst mode controller

Objective speciﬁcation Supersedes data of October 1992 File under Integrated Circuits, IC17

1996 Oct 31

Philips Semiconductors Objective speciﬁcation

DECT burst mode controller PCD5041

FEATURES 2 GENERAL DESCRIPTION 3 ORDERING INFORMATION 4 BLOCK DIAGRAM 5 PINNING 6 FUNCTIONAL DESCRIPTION

6.1 Internal bus and data memory

6.1.1 Internal Bus

6.1.2 Data Memory

6.2 Clock generation and correction

6.3 Programmable communication controller and

program memory

6.3.1 PCC

6.3.2 PCC functions

6.4 Speech interface

6.4.1 12-slot mode

6.4.2 Muting

6.4.3 Local call

6.5 RF interface

6.5.1 Serial receiver

6.5.2 Serial transmitter

6.5.3 Seamless handover

6.5.4 RF control signals

6.5.5 Synthesizer programming

6.5.6 RSSI measurement

6.5.7 Local call switching

6.5.8 Data synchronization

6.5.9 Ciphering machine

6.5.10 Comparator/data slicer on PCD5041HZ

6.6 Microcontroller Interface

6.6.1 Function of the microcontroller interface

6.6.2 Microcontroller interrupts

6.6.3 Watchdog

6.6.4 Power-down

6.7 Survey of registers 7 LIMITING VALUES 8 CHARACTERISTICS 9 PACKAGE OUTLINES 10 SOLDERING

10.1 Introduction

10.2 Reflow soldering

10.3 Wave soldering

10.4 Repairing soldered joints 11 DEFINITIONS 12 LIFE SUPPORT APPLICATIONS

1996 Oct 31 2

Philips Semiconductors Objective speciﬁcation

DECT burst mode controller PCD5041

1 FEATURES

• On-chip pre-programmed Communication Controller

with embedded firmware for implementation of Traffic Bearer Control (TBC), MAC message handling, scanning, and control of the device’s other functional units.

• Portable Part (PP) modes

• TDMA frame (de)multiplexing

• Encryption

• Scrambling

• CRC generation and checking

• Beacon transmission control (by P00 packets)

• On-chip comparator for receive data slicer function (only

available in the LQFP80 package)

• Switches up to12 active speech channels from speech

interface to 1152 kbit/s. radio interface, and vice versa

• Dual channel speech/data capability

• Received Signal Strength Indication (RSSI)

measurement, with on-chip 6-bits peak/hold detector

• Quality control report

• Digital Phase Locked Loop (DPLL)

• Synchronization (handset to active bearer, base station

to cluster of RFPs)

• Seamless handover procedure

• Fast (hardware) and slow (software) mute function

• 1 kbyte extended RAM memory

• On-chip crystal oscillator (13.824 MHz)

• Programmable microcontroller clock frequency

• Programmable interrupts

• Watchdog with two programmable time-outs

• Low power consumption in standby mode

• Low supply voltage (2.7 to 5.5 V)

• SACMOS technology.

2 GENERAL DESCRIPTION

The PCD5041 DECT Burst Mode Controller (BMC) is a custom IC that performs the DECT Physical Layer and MAC Layer time-critical functions, for use in DECT handset products which comply with the following standards (and updates):

• DECT CI part 2: Physical layer (DE/RES 3001-2)

• DECT CI part 3 : Medium Access Control layer

(DE/RES 3001-3)

• DECT CI part 7: Security features for DECT (DE/RES 3001-7)

• DECT CI part 9: Public Access Profile (DE/RES 3001-9).

The PCD5041 has interfaces to:

• ADPCM CODECs in the handset mode

• A radio transceiver; the interface is fully decoded, and

includes power-down signals

• An external microcontroller.

The PCD5041 is designed to be connected to an ADPCM CODEC (Philips’ PCD5032, for example) and an 80C51-type microcontroller. Other microcontrollers (e.g.

68000) and CODECs can also be supported.

3 ORDERING INFORMATION

TYPE

NUMBER

PCD5041H QFP64

PCD5041HZ

1996 Oct 31 3

NAME DESCRIPTION VERSION

plastic quad flat package; 64 leads (lead length 1.95 mm); body 14 × 20 × 2.8 mm

LQFP80 plastic low profile quad flat package; 80 leads; body 12 × 12 × 1.4 mm

PACKAGE

SOT319-2

SOT315-1

Philips Semiconductors Objective speciﬁcation

DECT burst mode controller PCD5041

4 BLOCK DIAGRAM

handbook, full pagewidth

PCD5041

to CODEC/

Highway



DECT BURST MODE CONTROLLER

SPEECH

INTERFACE

TIMING, CONTROL,

CLOCK

GENERATION

internal

bus

DATA MEMORY

2 kbyte RAM

3-wire synthesizer

interface

Rx/Tx data

8051/68000

interface

RF INTERFACE

MICROCONTROLLER

INTERFACE

PROGRAMMABLE COMMUNICATION

CONTROLLER (PCC)

PCC

PROGRAM MEMORY

4 kbyte ROM

MBH705

Fig.1 Block diagram.

5 PINNING (see Figs 2 and 3)

SYMBOL

QFP64 LQFP80

AD0 to AD7 1 to 8 80, 1, and

(1)

(2)

TYPE

I/O address/Data bus

DESCRIPTION

3to7 ALE 9 9 I address latch enable CS 10 11 I chip select (active LOW) A8 to A10 13 to 11 14 to 12 I address bus V

DD1

PROC_CLK 15 16 O microcontroller clock; programmable from f

SS1

14 15 P positive supply 1

where f

is the crystal oscillator frequency

CLK

16 17 P negative supply 1

CLK

/64 to f

XTAL1 17 20 I crystal oscillator input XTAL2 18 21 O crystal oscillator output V

SS2

19 22 P negative supply

RESET_OUT 20 23 O watchdog timer output; intended to reset the external

microcontroller when expired RD 21 24 I read (active LOW) WR 22 25 I write (active LOW) RDY 23 26 O ready signal (active LOW), to initiate wait states in the

microcontroller (open drain)

CLK

1996 Oct 31 4

Philips Semiconductors Objective speciﬁcation

DECT burst mode controller PCD5041

SYMBOL

QFP64 LQFP80

(1)

TYPE

(2)

DESCRIPTION

INT 24 27 O interrupt (active LOW) CLK100 25 29 O 100 Hz frame timer V

SS3

26 31 P negative supply 3 DO 27 32 O 3-state data output on the speech interface FS3 − 33 I/O 8 kHz framing signal to ADPCM CODEC 1 output, for simple

base + handset, otherwise 8 kHz framing input

FS1 28 34 I/O 8 kHz framing signal to ADPCM CODEC 1 output, for simple

base + handset, otherwise 8 kHz framing input

FS4 − 35 I/O 8 kHz framing signal to ADPCM CODEC 1 output, for simple

base + handset, otherwise 8 kHz framing input

FS2 29 36 O 8 kHz framing signal to ADPCM CODEC 2 in the base station

mode DI 30 37 I data input on the speech interface DCK 31 38 O simple base + handset; 1152 kHz data clock (output),

otherwise 2048 kHz data clock (input) signal CLK3 32 39 O 3.456 MHz clock (nominal value, used to adjust system

timing) ANT_SW 33 40 O selects one of two antennas T_ENABLE 34 41 O Transmitter Enable (active LOW) T_POWER_RMP 35 43 O Transmitter Power Ramp control RMT_STAT 36 44 I serial 8-bit data can be read in for each slot; REMote radio SYNTH_LOCK 37 45 I lock indication from synthesizer V

SS4

38 46 P negative supply 4

REF_CLK 39 47 O reference frequency for the synthesizer, i.e. the crystal

DD2

oscillator clock f

40 48 P positive supply 2

CLK

S_ENABLE 41 49 O synthesizer enable S_CLK 42 51 O clock signal, to be used with S_DATA S_DATA 43 52 O serial data to the synthesizer S_POWER_DWN 44 53 O synthesizer power-down control VCO_BND_SW 45 54 O VCO bandswitch control signal 1200 HZ 46 55 O control signal for dual synthesizer schemes T_DATA 47 56 O serial output data to transmitter SET_OFF_IN 48 57 I switches off the crystal oscillator, and prevents all RF signals

from becoming active TEST1 49 58 I selects various test modes.; normal operation set to 0 RSSI_AN 50 60 I analog signal (for basic DECT systems), peak signal strength

measured after a lowpass ﬁlter TEST2 51 − I selects various test modes; normal operation set to 0 TEST3 52 61 I selects various test modes; normal operation set to 0 R_DATA 53 63 I receive data

1996 Oct 31 5

Philips Semiconductors Objective speciﬁcation

DECT burst mode controller PCD5041

SYMBOL

QFP64 LQFP80

(1)

TYPE

(2)

DESCRIPTION

R_ENABLE 54 64 O receiver enable (active LOW) R_POWER_DWN 55 65 O receiver power-down COMP_NE − 66 I digital input comparator not_enable (active LOW) SLICE_CTR 56 67 O slice time constant control COMP_OUT − 68 O digital comparator output V V

DD3 SS5

57 69 P positive supply 3

58 70 P negative supply 5 COMP_INM − 71 I analog comparator input negative V

REF

59 72 I reference input for the A/D converter COMP_INP − 73 I analog input positive V

DD(RAM)

60 74 P power supply for data RAM SYNCPORT 61 76 I/O in the base station the signal is the SYNCPORT RESET 62 77 I BMC master reset signal MEM_SEL 63 78 I selects PCC program memory at microcontroller interface EN_WATCHDOG 64 79 I enable watchdog input; when HIGH, the watchdog timer of

the BMC is enabled

Notes

1. Un-referenced pins for the LQFP80 package are not connected. FS3, FS4 and the comparator signals are only available in the LQFP80 package.

2. All signals which are input or I/O, and which can be floating, need to be pulled up to VDD or down to VSS in order to protect the device against cross-currents. Exceptions are VREF and RSSI_AN, which do not have to be protected.

1996 Oct 31 6

Philips Semiconductors Objective speciﬁcation

DECT burst mode controller PCD5041

handbook, full pagewidth

AD0 AD1 AD2 AD3 AD4 AD5

AD6 AD7 ALE

CSN

AD10

AD9 AD8

DD1

PROC_CLK

SS1

XTAL1 XTAL2

SS2

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16 17 18 19

EN_WATCHDOG

MEM_SEL

MEM_RESET

DD(RAM)

SYNCPORT

PCD5041H

VREF 59

SS5VDD3

SLICE_CTR

R_POWER_DWN

R_ENABLE

R_DATA

TEST3

51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33

TEST2 RSSI_AN TEST1 SET_OFF_IN T_DATA 1200_Hz VCO_BND_SW S_POWER_DWN S_DATA S_CLK

S_ENABLE V

DD2 REF_CLK V

SS4 SYNTH_LOCK RMT_STAT T_POWER_RMP T_ENABLE ANT_SW

RESET_OUT

RDY

INT

CLK100

Fig.2 Pin configuration, PCD5041H (QFP64 package).

1996 Oct 31 7

SS3

27 DO

FS1

FS2

DCK

MBH706

CLK3

Philips Semiconductors Objective speciﬁcation

DECT burst mode controller PCD5041

handbook, full pagewidth

AD1

n.c. AD2 AD3 AD4 AD5

AD6 AD7 ALE

n.c.

CSN

AD10

AD9 AD8

DD1

PROC_CLK

SS1

n.c.

XTAL1

AD0

EN_WATCHDOG

MEM_SEL

RESET

SYNCPORT

76 1 2 3 4 5 6 7 8 9

n.c. 75

DD(RAM)

COMP_INP

VREF 72

SS5VDD3

COMP_INN 71

SLICE_CTR

COMP_OUT 68

R_POWER_DWN

COMP_NE

R_ENABLE

R_DATA

TEST3

TEST2 61

60 59 58 57 56 55 54 53 52 51

RSSI_AN n.c. TEST1 SET_OFF_IN T_DATA 1200_Hz VCO_BND_SW S_POWER_DWN S_DATA S_CLK

PCD5041HZ

11 12 13 14 15 16 17 18 19 20

n.c. S_ENABLE

DD2

REF_CLK

SS4

SYNTH_LOCK

RMT_STAT

T_POWER_RMP

43 42

n.c. T_ENABLE

XTAL2

SS2

RESET_OUT

RDY

INT

n.c.

CLK100

Fig.3 Pin configuration, PCD5041HZ (LQFP80 package).

1996 Oct 31 8

SS3

32 DO

FS3

FS1

FS4

FS2

MBH707

DCK

CLK3

ANT_SW

Philips Semiconductors Objective speciﬁcation

DECT burst mode controller PCD5041

6 FUNCTIONAL DESCRIPTION (see Fig.1) The PCD5041 has dedicated hardware blocks containing

logic for time-critical functions requiring bit or byte-time accuracy. Other functions requiring only slot-time accuracy are performed by software in the Programmable Communication Controller (PCC). This approach offers maximum flexibility during prototyping.

6.1 Internal bus and data memory

6.1.1 I The function of the internal bus is:

• To provide access for all functional blocks to the common data memory

• To provide access for the microcontroller-interface and the PCC to all other functional blocks.

All functional blocks (speech-interface, RF-interface, microcontroller-interface and PCC) can autonomously use the internal bus to communicate with the common data memory.

A bus controller is used to handle the bus priority mechanism. When several blocks request access simultaneously, the request with the highest priority is handled first.

NTERNAL BUS

6.2 Clock generation and correction (see Fig.4) The device has an on-chip 13.824 MHz crystal oscillator.

From this source, a few frequencies are derived for internal and external use. Frequencies generated for external use are:

• 13.824 MHz for the synthesizer reference (pin REF_CLK). This output is only provided if the synthesizer power-down control (output on pin S_POWER_DWN) is not selected.

• 0.144 to 13.824 MHz for the microcontroller clock (pin PROC_CLK)

• 3.456 MHz for the ADPCM CODEC (pin CLK3)

• 1200 Hz (pin 1200_HZ) for dual synthesizer switching

• 100 Hz (pin CLK100) indicates start of frame.

Nominally, the frequency on pin CLK3 is 3.456 MHz. This frequency is obtained by dividing the crystal frequency by

4. Sometimes, the crystal frequency will be divided by 3

or by 5, to synchronize the combination of the ADPCM CODEC and the device to an external source. For the handset application, the PCD5041 can be synchronized to the incoming radio channel, using the ‘slot synchronization’ event of one active channel, so the handset is locked to one base station.

6.1.2 D A large part of the data memory is used for the bit rate

adaptation between the DECT radio interface and the speech interface. The data memory also acts as the main communication interface between the external microprocessor and the PCC.

In a handset, the device uses only 1 kbyte of the common data memory. The remaining 1 kbyte can be used by the microcontroller as an extended data memory for the higher layer software. The microcontroller is not aware of the fact that it is sharing the memory with the PCD5041. From the microcontroller’s point of view, the PCD5041’s microcontroller-interface plus the common data memory behave as a standard RAM device.

ATA MEMORY

1996 Oct 31 9

+ 19 hidden pages

Philips pcd5041 DATASHEETS

CONTENTS

1 FEATURES

2 GENERAL DESCRIPTION

3 ORDERING INFORMATION

4 BLOCK DIAGRAM

5 PINNING (see Figs 2 and 3)

6 FUNCTIONAL DESCRIPTION (see Fig.1) The PCD5041 has dedicated hardware blocks containing

6.1 Internal bus and data memory

6.2 Clock generation and correction (see Fig.4) The device has an on-chip 13.824 MHz crystal oscillator.