Philips CDM-i25w, PAR38-ALTO User Manual

Philips MasterColor

Integrated 25W PAR38

eramic Metal Halide

C Lamps featuring ALTO Lamp Technology

Ideal for general, ambient or accent lighting

CDM-i25w/PAR38/ALTO

This lamp is better for the environment

†

because of its reduced mercury content. All Philips ALTO

ptions which can simplify and reduce your

o lamp disposal costs depending on your state and local regulations.

lamps give you end-of-life

Transform your business with a simple twist!

The Philips MasterColor®Integrated 25W is an all-in-one lamp and ballast in a PAR38 reflector.

MasterColor®technology

• Energy savings—Up to 3x less energy consumption than standard PAR38 halogen lamps with comparable light output

• 15,000 hours rated average life1—Lasts up to 3x longer than standard halogen PAR38

• Very good color rendering of 87, crisp white light (3000K)

Integrated electronic ballast

• Easy upgrade and instant retrofit from halogen PAR38

Familiar PAR38 shape and size

• Simple ‘twist in’ for one step easy installation

• Easy maintenance

• 10º, 25º, and 40º beam spread

(1, See back of page for footnote)

Philips MasterColor®Integrated 25W PAR38 Ceramic Metal Halide Lamps

Spectral Power Distribution

Power (W per nm)

200 300 400 500 600 700 800

avelength (Nanometers)

0.08

0.07

0.06

0.05

.04

0.03

0.02

0.01

featuring ALTO

Lamp Technology

Ordering Data

roduct Pkg.

umber Ordering Code Qty. Beam MBCP

4477-4 CDM-i25W/830/PAR38/10/ALTO 6 Spot (10˚) 26,000

4478-2 CDM-i25W/830/PAR38/25/ALTO 6 Flood (25˚) 5600

4479-0 CDM-i25W/830/PAR38/40/ALTO 6 Wide Flood (40˚) 2100

Electrical and Technical Data

attage ––––––––––––––––––––––––––––––––25W

nput Voltage ––––––––––––––––––––––––120V±10%

ax.THD –––––––––––––––––––––––––––––––142%

requency–––––––––––––––––––––––––––––––60Hz

nput Current

arm-up to 80% Full Brightness –––––––––2 minutes

estrikeTime for Hot Lamps–––––––––– 5-7 minutes

inimum Operating Temp.–––––––––––– -20˚C (-4˚F)

–––––––––––––––––––––––––––0.36

–

Physical Characteristics

ulb Size–––––––––––––––––––––––––––––––PAR38

ulb Finish ––––––––––––––––––––––––––––––Clear

ase –––––––––––––––––––––––––––––––––Medium

ax. Overall Length (MOL) –––––––––5.33'' (135mm)

ight Center Length (LCL) ––––––––––––––––––N/A

rc Length–––––––––––––––––––––––––––––––N/A

rc Tube Material ––––––––––Polycrystalline Alumina

ax. Ring Temp. ––––––––––––––––––––65ºC (149ºF)

ax. Cap Temp. ––––––––––––––––––––65ºC (149ºF)

ax. Neck Temp. –––––––––––––––––––80˚C (176˚F)

ax.Arc Tube to Base Eccentricity ––––––––––––––3º

Operating Characteristics

Approx. Initial Lumens4–––––––––––––––––––––1275 Approx. Mean Lumens Rated Average Life, Hours. Correlated ColorTemp. (CCT) CIE Chromaticity Approx. Color Rendering Index (CRI)––––––––––––––––––87 Efficacy (lpw)–––––––––––––––––––––––––––––––51 Beam Angle (at 50% of MBCP)––––––––––10˚/25˚/40˚

–––––––––––––––––––––880

––––––––––––––––15,000

––––––––––––3000K

–––––––––––x-.440, y-.393

Operating Position

Universal-Open or Enclosed PAR Style Luminaires (Do not use in totally enclosed recessed luminaires.)

1) Rated average life is the life obtained, on the average, from large representative groups of lamps in laboratory tests under controlled conditions at 10 or more operating hours per start. It is based on survival of at least 50% of the lamps and allows for individual lamps or groups of lamps to vary considerably from the average.

2) Maximum Beam Candlepower.

3) CAUTION:New construction should allow for the current used by these lamps. Because of a power factor of 0.57 in the ballast of the lamp, the lamp uses .36 amps.

4) Measured at 100 hrs. life. Approximate lumen values listed are for vertical operation of the lamp.

5) Approximate lumen output at 40% of lamp rated average life.

This product utilizes ALTO Procedure (TCLP) and can be classiﬁed as non-hazardous waste. Check with state and local regulations.

Above specifications subject to change without notice.

Lamp Technology.ALTO products pass the US EPA'sToxicity Characteristic Leaching

CDM-i25w/PAR38/ALTO

arnings,Cautions and Operating Instructions

WARNING: These lamps can cause serious skin burn

nd eye inflammation from short wave ultraviolet radiation

a if outer envelope of the lamp is broken or punctured. Do

ot use where people will remain for more than a few

inutes unless adequate shielding or other safety precautions

m are used. Certain lamps that will automatically extinguish

hen the outer envelope is broken or punctured are

w commercially available.”This lamp complies with FDA

adiation performance standard 21 CFR subchapter J.

r (USA:21CFR 1040.30 Canada:SOR/DORS/80-381)

f the outer bulb is broken or punctured, turn off at

nce and replace the lamp to avoid possible injury

o from hazardous short wave ultraviolet radiation. Do

ot scratch the outer bulb or subject it to pressure

n as this could cause the outer bulb to crack or shatter.

partial vacuum in the outer bulb may cause glass

A to fly if the envelope is struck.

WARNING: The arc-tube of metal halide lamps are designed

o operate under high pressure and at temperatures up to

t 1000°C and can unexpectedly rupture due to internal or

xternal factors such as a ballast failure or misapplication.

e If the arc-tube ruptures for any reason, the outer bulb may

reak and pieces of extremely hot glass might be discharged

b into the surrounding environment.If such a rupture were to happen,THERE IS A RISK OF PERSONAL INJURY,

PROPERTY DAMAGE,BURNS AND FIRE.

his lamp contains an arc tube with a filling gas

T containing less than 41 nCi of Kr-85 and is distributed

y Philips Lighting Company,a division of Philips

b Electronics NorthAmerica Corporation, Somerset, New Jersey, 08875.

CAUTION:TO REDUCETHE RISK OF PERSONAL INJURY,

PROPERTY DAMAGE, BURNS AND FIRE RESULTING FROMAN ARC-TUBE RUPTURE THE FOLLOWING LAMP OPERATING INSTRUCTIONS

LAMP OPERATING INSTRUCTIONS:

1. At high lighting levels or when illuminating light-sensitive materials the use of an extra UV filter is recommended.

2. Before lamp installation/replacement, shut power off and allow lamp and fixture to cool to avoid electrical shock and potential burn hazards.

3.Time should be allowed for lamps to stabilize in color

when turned on for the first time.This may require several hours of operation, with more than one start.Lamp color is also subject to change under conditions of excess vibration or shock, and color appearance may vary between individual lamps.

4. Lamps may require up to 10 minutes to re-light if there is a power interruption.

5. Do not operate with an additional ballast, since a ballast is integrated in the lamp itself.

6. Do not use in totally enclosed recessed fixtures.

7. Take care in handling and disposing of lamps. If an arc tube is broken, avoid skin contact with any of the contents or fragments.

8. Lamp should not be used with dimmers.

9. Protect lamp, lamp socket and wiring against moisture, corrosive atmosphere and excessive heat.Lamp should be used in dry locations only.

These lamps may be used in open fixtures.

Hg: LAMP CONTAINS MERCURY Manage in Accord with Disposal Laws See: www.lamprecycle.org or 1-800-555-0050

MUST BE FOLLOWED.

P-5747-F

www.philips.com

Philips Lighting Company 200 Franklin Square Drive P.O.Box 6800 Somerset, NJ 08875-6800 1-800-555-0050

A Division of Philips Electronics North America Corporation

Philips Lighting 281 Hillmount Road Markham, Ontario Canada L6C 2S3 1-800-555-0050

A Division of Philips Electronics Ltd.