Philips P89LPC907, P89LPC906, P89LPC908 User Manual

Download

INTEGRATED CIRCUITS

USER MANUAL

P89LPC906/907/908

8-bit microcontrollers with accelerated two-clock 80C51 core 1KB 3V Low-Power byte-eraseable Flash with 128 Byte RAM

Philips Semiconductors

PHILIPS

2003 Dec 8

Philips Semiconductors

User’s Manual - Preliminary -

Table of Contents

P89LPC906/907/908

1. General Description................................................................................ 7

Pin Configurations ..................................................................................... 7

Product comparison................................................................................... 8

Pin Descriptions - P89LPC906 ................................................................ 12

Pin Descriptions - P89LPC907 ................................................................ 13

Pin Descriptions - P89LPC908 ................................................................ 14

Special function registers ......................................................................... 15

Memory Organization .............................................................................. 24

2. Clocks................................................................................................... 25

Enhanced CPU ........................................................................................ 25

Clock Definitions ...................................................................................... 25

CPU Clock (OSCCLK) ............................................................................. 25

Low Speed Oscillator Option - P89LPC906............................................. 25

Medium Speed Oscillator Option - P89LPC906 ...................................... 25

High Speed Oscillator Option - P89LPC906............................................ 25

Oscillator Option Selection- P89LPC906................................................. 26

Clock Output - P89LPC906 ..................................................................... 26

On-Chip RC oscillator Option .................................................................. 26

If CCLK is 8MH or slower, the CLKLP SFR bit (AUXR1.7) can be set to ’1’ to reduce power consumption. On reset, CLKLP is ’0’ allowing highest performance access. This bit

can then be set in software if CCLK is running at 8MHz or slower ............................... 26

Watchdog Oscillator Option ..................................................................... 26

External Clock Input Option - P89LPC906 .............................................. 27

CPU Clock (CCLK) Wakeup Delay.......................................................... 27

CPU Clock (CCLK) Modification: DIVM Register..................................... 27

Low Power Select (P89LPC906) ........................................................... 28

................................................................................................................. 29

3. Interrupts .............................................................................................. 31

Interrupt Priority Structure........................................................................ 31

External Interrupt Inputs .......................................................................... 32

External Interrupt Pin Glitch Suppression................................................ 32

4. I/O Ports ............................................................................................... 35

Port Configurations.................................................................................. 35

Quasi-Bidirectional Output Configuration ................................................ 35

Open Drain Output Configuration ............................................................ 36

Input-Only Configuration.......................................................................... 37

Push-Pull Output Configuration ............................................................... 37

Port 0 Analog Functions .......................................................................... 37

5. Timers 0 and 1...................................................................................... 41

Mode 0..................................................................................................... 42

Mode 2..................................................................................................... 42

Mode 3..................................................................................................... 43

Mode 6 - P89LPC907 .............................................................................. 43

Timer Overflow toggle output - P89LPC907............................................ 45

2003 Dec 8 2

Philips Semiconductors

User’s Manual - Preliminary -

Table of Contents

P89LPC906/907/908

6. Real-Time Clock/System Timer............................................................ 47

Real-time Clock Source........................................................................... 47

Changing RTCS1-0 ................................................................................. 50

Real-time Clock Interrupt/Wake Up ......................................................... 50

Reset Sources Affecting the Real-time Clock.......................................... 50

7. Power Monitoring Functions ................................................................. 53

Brownout Detection ................................................................................. 53

Power-On Detection ................................................................................ 54

Power Reduction Modes.......................................................................... 54

8. UART (P89LPC907, P89LPC908)........................................................ 59

Mode 0..................................................................................................... 59

Mode 1..................................................................................................... 59

Mode 2..................................................................................................... 59

Mode 3..................................................................................................... 59

SFR Space .............................................................................................. 60

Baud Rate Generator and Selection........................................................ 60

Updating the BRGR1 and BRGR0 SFRs................................................. 60

Framing Error........................................................................................... 61

Break Detect............................................................................................ 61

More About UART Mode 0 ...................................................................... 63

More About UART Mode 1 ...................................................................... 64

More About UART Modes 2 and 3........................................................... 65

Framing Error and RI in Modes 2 and 3 with SM2 = 1 ............................ 65

Break Detect............................................................................................ 65

Double Buffering...................................................................................... 66

Double Buffering in Different Modes........................................................ 66

Transmit Interrupts with Double Buffering Enabled (Modes 1, 2 and 3) .. 66

The 9th Bit (Bit 8) in Double Buffering (Modes 1, 2 and 3)...................... 67

Multiprocessor Communications.............................................................. 68

Automatic Address Recognition............................................................... 68

9. Reset .................................................................................................... 71

Power-On reset code execution .............................................................. 71

10. Analog Comparators........................................................................... 73

Comparator Configuration ....................................................................... 73

Internal Reference Voltage ...................................................................... 74

Comparator Interrupt ............................................................................... 74

Comparator and Power Reduction Modes............................................... 74

Comparator Configuration Example ........................................................ 75

11. Keypad Interrupt (KBI)........................................................................ 77

12. Watchdog Timer ................................................................................. 79

Watchdog Function.................................................................................. 79

Feed Sequence ....................................................................................... 80

Watchdog Timer in Timer Mode .............................................................. 83

2003 Dec 8 3

Philips Semiconductors

User’s Manual - Preliminary -

Table of Contents

P89LPC906/907/908

Power down operation ............................................................................. 84

Watchdog Clock Source .......................................................................... 84

Periodic wakeup from Power down without an external oscillator ........... 85

13. Additional Features............................................................................. 87

Software Reset ........................................................................................ 87

Dual Data Pointers................................................................................... 87

14. Flash program memory ...................................................................... 89

General description.................................................................................. 89

Features................................................................................................... 89

Introduction to IAP-Lite ............................................................................ 89

Using Flash as data storage .................................................................... 89

Accessing additional flash elements........................................................ 92

Erase-programming additional flash elements ........................................ 93

Reading additional flash elements........................................................... 93

User Configuration Bytes......................................................................... 96

User Security Bytes ................................................................................. 97

Boot Vector.............................................................................................. 98

Boot Status .............................................................................................. 98

15. Instruction set ..................................................................................... 99

16. Revision History................................................................................ 103

17. Index................................................................................................. 105

2003 Dec 8 4

Philips Semiconductors

User’s Manual - Preliminary -

List of Figures

P89LPC906/907/908

List of Figures

Special function registers table - P89LPC906. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Special function registers table - P89LPC907. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Special function registers table - P89LPC908. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

P89LPC906/907/908 Memory Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Using the Crystal Oscillator - P89LPC906 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

On-Chip RC Oscillator TRIM Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Block Diagram of Oscillator Control - P89LPC906 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Block Diagram of Oscillator Control- P89LPC907,P89LPC908 . . . . . . . . . . . . . . . . . . . . 29

Interrupt priority level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Summary of Interrupts - P89LPC906 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Summary of Interrupts - P89LPC907,P89LPC908 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Interrupt sources, enables, and Power down Wake-up sources - P89LPC906 . . . . . . . . 33

Interrupts sources, enables, and Power down Wake-up sources - P89LPC907,P89LPC908 33

Number of I/O Pins Available . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Port Output Configuration Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Quasi-Bidirectional Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Open Drain Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Input Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Push-Pull Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Port Output Configuration - P89LPC906 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Port Output Configuration - P89LPC907 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Port Output Configuration - P89LPC908. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Additional Port Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Timer/Counter Mode Control register (TMOD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Timer/Counter Auxiliary Mode Control register (TAMOD). . . . . . . . . . . . . . . . . . . . . . . . . 42

Timer/Counter Control register (TCON) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Timer/Counter 0 or 1 in Mode 0 (13-bit counter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Timer/Counter 0 or 1 in Mode 1 (16-bit counter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Timer/Counter 0 or 1 in Mode 2 (8-bit auto-reload). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Timer/Counter 0 Mode 3 (two 8-bit counters) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Timer/Counter 0 in Mode 6 (PWM auto-reload), P89LPC907. . . . . . . . . . . . . . . . . . . . . . 45

Real-time clock/system timer Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Real-time Clock/System Timer Clock Source - P89LPC906. . . . . . . . . . . . . . . . . . . . . . . 48

Real-time Clock/System Timer Clock Source - P89LPC907,P89LPC908 . . . . . . . . . . . . 49

RTCCON Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Brownout Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Power Reduction Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Power Control Register (PCON) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Power Control Register (PCONA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

SFR Locations for UARTs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Baud Rate Generation for UART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

BRGCON Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Baud Rate Generations for UART (Modes 1, 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

2003 Dec 8 5

Philips Semiconductors

User’s Manual - Preliminary -

List of Figures

P89LPC906/907/908

Serial Port Control Register (SCON). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Serial Port Status Register (SSTAT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Serial Port Mode 0 (Double Buffering Must Be Disabled) . . . . . . . . . . . . . . . . . . . . . . . . . 64

Serial Port Mode 1 (Only Single Transmit Buffering Case Is Shown) . . . . . . . . . . . . . . . . 64

Serial Port Mode 2 or 3 (Only Single Transmit Buffering Case Is Shown) . . . . . . . . . . . . 65

FE and RI when SM2 = 1 in Modes 2 and 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Transmission with and without Double Buffering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Block Diagram of Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Reset Sources Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Comparator Control Register (CMP1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Comparator Input and Output Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Comparator Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Keypad Pattern Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Keypad Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Keypad Interrupt Mask Register (KBM). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

.Watchdog timer configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Watchdog Prescaler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Watchdog Timer Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

P89LPC906/907/908 Watchdog Timeout Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Watchdog Timer in Watchdog Mode (WDTE = 1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Watchdog Timer in Timer Mode (WDTE = 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

AUXR1 Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Flash Memory Control Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Assembly language routine to erase/program all or part of a page. . . . . . . . . . . . . . . . . . 92

C-language routine to erase/program all or part of a page . . . . . . . . . . . . . . . . . . . . . . . . 92

Flash elements accesable through IAP-Lite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

Assembly language routine to erase/program a flash element . . . . . . . . . . . . . . . . . . . . . 94

C-language routine to erase/program a flash element . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

C-language routine to read a flash element . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Flash User Configuration Byte 1 (UCFG1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

User Sector Security Bytes (SEC0 ... SEC3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

Effects of Security Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

Boot Vector (BOOTVEC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

Boot Status (BOOTSTAT). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

Instruction set summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

2003 Dec 8 6

Philips Semiconductors

User’s Manual - Preliminary -

P89LPC906/907/908GENERAL DESCRIPTION

1. GENERAL DESCRIPTION

The P89LPC906/907/908 is a single-chip microcontroller designed for applications demanding high-integration, low cost solutions over a wide range of performance requirements. The P89LPC906/907/908 is based on a high performance processor architecture that executes instructions six times the rate of standard 80C51 devices. Many system level functions have been incorporated into the P89LPC906/907/908 in order to reduce component count, board space, and system cost.

PIN CONFIGURATIONS

8-Pin Packages

P89LPC906

RST

/P1.5

VSS

P0.6/CMP1/KBI6

XTAL1/P3.1

P0.4/CIN1A/KBI4

P0.5/CMPREF/KBI5

VDD

CLKOUT/XTAL2/P3.0

RST/P1.5

VSS

P0.6/CMP1/KBI6

P1.2/T0

/P1.5

RST

VSS

P0.6/CMP1/KBI6

P1.1/RxD

P89LPC907

P89LPC908

P0.4/CIN1A/KBI4

P0.5/CMPREF/KBI5

VDD

P1.0/TxD

P0.4/CIN1A/KBI4

P0.5/CMPREF/KBI5

VDD

P1.0/TXD

2003 Dec 8 7

Philips Semiconductors

Logic Symbols

VDDV

User’s Manual - Preliminary -

P89LPC906/907/908GENERAL DESCRIPTION

KBI4 KBI5

CLKOUT

KBI4 KBI5 KBI6

CIN1A

CMPREF

CMP1KBI6

PORT0

XTAL2

XTAL1

CIN1A

CMPREF

CMP1

CIN1A

CMPREF

CMP1 RxD

PORT3

PORT0

P89

LPC906

VDDV

P89

LPC907

VDDV

P89

LPC908

PORT1

RST

T0 TxD

RST

TxD

PRODUCT COMPARISON

The following table highlights differences between these three devices.

Part number Ext crystal pins CLKOUT output T0 PWM output

P89LPC906 XX-X--

P89LPC907 --XXX-

P89LPC908 ---XXX

2003 Dec 8 8

Analog

comparator

UART

TxD RxD

Philips Semiconductors

Block Diagram - P89LPC906

Accelerated 2-clock 80C51

1 KB Code

Flash

128 byte

Data RAM

Port 3

Configurable I/Os

Port 1

Input

High Performance

CPU

Internal Bus

Real-Time Clock/

User’s Manual - Preliminary -

P89LPC906/907/908GENERAL DESCRIPTION

Timer0 Timer1

System Timer

Crystal or

Resonator

Port 0

Configurable I/Os

Keypad

Interrupt

Watchdog Timer

and Oscillator

Programmable

Oscillator Divider

Configurable

Oscillator

CPU

Clock

On-Chip

Oscillator

Analog

Comparator

Power Monitor

(Power-On Reset,

Brownout Reset)

2003 Dec 8 9

Philips Semiconductors

Block Diagram - P89LPC907

User’s Manual - Preliminary -

P89LPC906/907/908GENERAL DESCRIPTION

High Performance

Accelerated 2-clock 80C51

CPU

1 KB Code

Flash

Internal Bus

UART

128 byte

Data RAM

Timer0 Timer1

Port 1

Configurable I/O

Port 0

Configurable I/Os

Keypad

Interrupt

Watchdog Timer

and Oscillator

Programmable

Oscillator Divider

On-Chip

Oscillator

Real-Time Clock/

System Timer

Analog

Comparator

CPU

Clock

Power Monitor

(Power-On Reset,

Brownout Reset)

2003 Dec 8 10

Philips Semiconductors

Block Diagram - P89LPC908

User’s Manual - Preliminary -

P89LPC906/907/908GENERAL DESCRIPTION

High Performance

Accelerated 2-clock 80C51

CPU

1 KB Code

Flash

128 byte

Data RAM

Port 1

Configurable I/Os

Port 0

Configurable I/Os

Keypad

Interrupt

Watchdog Timer

and Oscillator

Programmable

Oscillator Divider

UART

Internal Bus

Timer0 Timer1

Real-Time Clock/

System Timer

Analog

Comparator

CPU

Clock

On-Chip

Oscillator

2003 Dec 8 11

Power Monitor

(Power-On Reset,

Brownout Reset)

Philips Semiconductors

User’s Manual - Preliminary -

P89LPC906/907/908GENERAL DESCRIPTION

PIN DESCRIPTIONS - P89LPC906

Mnemonic Pin no. Type Name and function

P0.4 - P0.6 3, 7,8 I/O Port 0: Port 0 is an I/O port with a user-configurable output types. During reset Port

0 latches are configured in the input only mode with the internal pullup disabled. The operation of port 0 pins as inputs and outputs depends upon the port configuration selected. Each port pin is configured independently. Refer to the section Port Configurations on page 35 and the DC Electrical Characteristics in the datasheet for details.

The Keypad Interrupt feature operates with port 0 pins.

All pins have Schmitt triggered inputs.

Port 0 also provides various special functions as described below.

8I/OP0.4 Port 0 bit 4.

I CIN1A Comparator 1 positive input. I KBI4 Keyboard Input 4.

7I/OP0.5 Port 0 bit 5.

I CMPREFComparator reference (negative) input. I KBI5 Keyboard Input 5.

3I/OP0.6 Port 0 bit 6.

O CMP1 Comparator 1 output.

I KBI6 Keyboard Input 6.

P1.5 1 I P1.5 Port 1 bit 5. (Input only)

I RST

P3.0 - P3.1 4,5 I/O Port 3 Port 3 is an I/O port with a user-configurable output types. During reset Port

All pins have Schmitt triggered inputs.

Port 3 also provides various special functions as described below:

5I/OP3.0 Port 3 bit 0.

O XTAL2 Output from the oscillator amplifier (when a crystal oscillator option is

OCLKOUTCPU clock divided by 2 when enabled via SFR bit (ENCLK - TRIM.6). It can

4I/OP3.1 Port 3 bit 1.

I XTAL1 Input to the oscillator circuit and internal clock generator circuits (when

2IGround: 0V reference.

6IPower Supply: This is the power supply voltage for normal operation as well as Idle and

Power down modes.

External Reset input during power-on or if selected via UCFG1. When functioning as a reset input a low on this pin resets the microcontroller, causing I/O ports and peripherals to take on their default states, and the processor begins execution at address 0. Also used during a power-on sequence to force In-Circuit Programming mode.

3 latches are configured in the input only mode with the internal pullups disabled. The operation of port 3 pins as inputs and outputs depends upon the port configuration selected. Each port pin is configured independently. Refer to the section Port Configurations on page 35 and the DC Electrical Characteristics in the datasheet for details.

selected via the FLASH configuration).

be used if the CPU clock is the internal RC oscillator, watchdog oscillator or external clock input, except when XTAL1/XTAL2 are used to generate clock source for the Real-Time clock/system timer.

selected via the FLASH configuration). It can be a port pin if internal RC oscillator or watchdog oscillator is used as the CPU clock source, AND if XTAL1/XTAL2 are not used to generate the clock for the Real-Time clock/ system timer.

2003 Dec 8 12

Philips Semiconductors

User’s Manual - Preliminary -

P89LPC906/907/908GENERAL DESCRIPTION

PIN DESCRIPTIONS - P89LPC907

Mnemonic Pin no. Type Name and function

P0.4 - P0.6 3, 7,8 I/O Port 0: Port 0 is an I/O port with a user-configurable output types. During reset Port

The Keypad Interrupt feature operates with port 0 pins.

All pins have Schmitt triggered inputs.

Port 0 also provides various special functions as described below.

8 I/O P0.4 Port 0 bit 4.

I CIN1A Comparator 1 positive input. I KBI4 Keyboard Input 4.

7 I/O P0.5 Port 0 bit 5.

I CMPREFComparator reference (negative) input. I KBI5 Keyboard Input 5.

3 I/O P0.6 Port 0 bit 6.

O CMP1 Comparator 1 output.

I KBI6 Keyboard Input 6.

P1.0-P1.5 1,4,5 Port 1: Port 1 is an I/O port with a user-configurable output types. During reset Port

1 latches are configured in the input only mode with the internal pull-up disabled. The operation of the configurable port 1 pins as inputs and outputs depends upon the port configuration selected. Each of the configurable port pins are programmed independently. Refer to the section Port Configurations on page 35 and the DC Electrical Characteristics in the datasheet for details.

P1.5 is input only.

All pins have Schmitt triggered inputs.

Port 1 also provides various special functions as described below.

5 I/O P1.0 Port 1 bit 0.

O TxD Serial port transmitter data.

4 I/O P1.2 Port 1 bit 2.

I/O T0 Timer 0 external clock input, toggle output, PWM output.

1IP1.5 Port 1 bit 5. (Input only)

I RST

2IGround: 0V reference.

6IPower Supply: This is the power supply voltage for normal operation as well as Idle

and Power down modes.

2003 Dec 8 13

Philips Semiconductors

User’s Manual - Preliminary -

P89LPC906/907/908GENERAL DESCRIPTION

PIN DESCRIPTIONS - P89LPC908

Mnemonic Pin no. Type Name and function

P0.4 - P0.6 3, 7,8 I/O Port 0: Port 0 is an I/O port with a user-configurable output types. During reset Port

The Keypad Interrupt feature operates with port 0 pins.

All pins have Schmitt triggered inputs.

Port 0 also provides various special functions as described below.

8 I/O P0.4 Port 0 bit 4.

I CIN1A Comparator 1 positive input. I KBI4 Keyboard Input 4.

7 I/O P0.5 Port 0 bit 5.

I CMPREFComparator reference (negative) input. I KBI5 Keyboard Input 5.

3 I/O P0.6 Port 0 bit 6.

O CMP1 Comparator 1 output.

I KBI6 Keyboard Input 6.

P1.0 - P1.5 1,4,5 Port 1: Port 1 is an I/O port with a user-configurable output types. During reset Port

P1.5 is input only.

All pins have Schmitt triggered inputs.

Port 1 also provides various special functions as described below.

5 I/O P1.0 Port 1 bit 0.

O TxD Serial port transmitter data.

4 I/O P1.1 Port 1 bit 1.

I RxD Serial port receiver data.

1IP1.5 Port 1 bit 5. (Input only)

I RST

2IGround: 0V reference.

6IPower Supply: This is the power supply voltage for normal operation as well as Idle

and Power down modes.

2003 Dec 8 14

Philips Semiconductors

User’s Manual - Preliminary -

P89LPC906/907/908GENERAL DESCRIPTION

Special function registers

Note: Special function registers (SFRs) accesses are restricted in the following ways:

1. User must NOT attempt to access any SFR locations not defined.

2. Accesses to any defined SFR locations must be strictly for the functions for the SFRs.

3. SFR bits labeled ’-’, ’0’ or ’1’ can ONLY be written and read as follows:

- ’-’ Unless otherwise specified, MUST be written with ’0’, but can return any value when read (even if it was written with ’0’). It is a reserved bit and may be used in future derivatives.

- ’0’ MUST be written with ’0’, and will return a ’0’ when read.

- ’1’ MUST be written with ’1’, and will return a ’1’ when read.

Table 1: Special function registers table - P89LPC906

Name Description

ACC* Accumulator E0H 00H 00000000

AUXR1# Auxiliary Function Register A2H CLKLP - - ENT0 SRST 0 - DPS 00H

SFR

Address

MSB

E7 E6 E5 E4 E3 E2 E1 E0

Bit Functions and Addresses Reset Value

LSB

Hex Binary

000000x0

F7 F6 F5 F4 F3 F2 F1 F0

B* B Register F0H 00H 00000000

CMP1# Comparator 1Control Register ACH - - CE1 - CN1 OE1 CO1 CMF1 00H

DIVM# CPU Clock Divide-by-M Control 95H 00H 00000000

DPTR Data Pointer (2 bytes)

DPH Data Pointer High 83H 00H 00000000

DPL Data Pointer Low 82H 00H 00000000

FMADRH# Program Flash Address High E7H 00H 00000000

FMADRL# Program Flash Address Low E6H 00H 00000000

Program Flash Control (Read)

FMCON#

FMDATA# Program Flash Data E5H 00H 00000000

IEN0* Interrupt Enable 0 A8H EA EWDRT EBO - ET1 - ET0 - 00H 00000000

IEN1*# Interrupt Enable 1 E8H - - - - - EC EKBI - 00H

IP0* Interrupt Priority 0 B8H - PWDRT PBO - PT1 - PT0 - 00H

Program Flash Control (Write)

BUSY - - - HVA HVE SV OI 70H 01110000

E4H

FMCMD.7FMCMD.6FMCMD.5FMCMD.4FMCMD.3FMCMD.2FMCMD.1FMCMD.

EF EE ED EC EB EA E9 E8

BF BE BD BC BB BA B9 B8

xx000000

00x00000

x0000000

IP0H# Interrupt Priority 0 High B7H -

IP1*# Interrupt Priority 1 F8H - - - - - PC PKBI - 00H

2003 Dec 8 15

PWDRT

FF FE FD FC FB FA F9 F8

PBOH - PT1H - PT0H - 00H

x0000000

00x00000

Philips Semiconductors

User’s Manual - Preliminary -

P89LPC906/907/908GENERAL DESCRIPTION

Name Description

SFR

Address

MSB

Bit Functions and Addresses Reset Value

LSB

Hex Binary

IP1H# Interrupt Priority 1 High F7H - - - - - PCH PKBIH - 00H100x00000

KBCON# Keypad Control Register 94H - - - - - -

PATN_S

KBIF 00H

xxxxxx00

KBMASK# Keypad Interrupt Mask Register 86H 00H 00000000

KBPATN# Keypad Pattern Register 93H FFH 11111111

87 86 85 84 83 82 81 80

P0* Port 0 80H -

KB6

CMPREF/

KB5

CIN/1A

KB4

---- Note 1

CMP1/

97 96 95 94 93 92 91 90

P1* Port 1 90H - - RST

-----

B7 B6 B5 B4 B3 B2 B1 B0

P3*Port 3 B0H------XTAL1XTAL2Note 1

P0M1# Port 0 Output Mode 1 84H - (P0M1.6) (P0M1.5) (P0M1.4) - - - - FFH 11111111

P0M2# Port 0 Output Mode 2 85H - (P0M2.6) (P0M2.5) (P0M2.4) - - - - 00H 00000000

P1M1# Port 1 Output Mode 1 91H - - (P1M1.5) - - - - - FFH

P1M2# Port 1 Output Mode 2 92H - - (P1M2.5) - - - - - 00H

P3M1# Port 3 Output Mode 1 B1H - - - - - - (P3M1.1) (P3M1.0) 03H

P3M2# Port 3 Output Mode 2 B2H - - - - - - (P3M2.1) (P3M2.0) 00H

11111111

00000000

xxxxxx11

xxxxxx00

PCON# Power Control Register 87H - - BOPD BOI GF1 GF0 PMOD1 PMOD0 00H 00000000

PCONA# Power Control Register A B5H RTCPD - VCPD - - - - -

00H

00000000

D7 D6 D5 D4 D3 D2 D1 D0

PSW* Program Status Word D0H CY AC F0 RS1 RS0 OV F1 P 00H 00000000

PT0AD# Port 0 Digital Input Disable F6H - - PT0AD.5 PT0AD.4 - - - - 00H xx00000x

RSTSRC# Reset Source Register DFH - - BOF POF - R_WD R_SF R_EX Note 2

1,5

RTCCON# Real-Time Clock Control D1H RTCF RTCS1 RTCS0 - - - ERTC RTCEN 60H

RTCH# Real-Time Clock Register High D2H 00H

RTCL# Real-Time Clock Register Low D3H 00H

011xxx00

00000000

SP Stack Pointer 81H 07H 00000111

TAMOD# Timer 0 Auxiliary Mode 8FH - - - - - - - T0M2 00H xxx0xxx0

8F 8E 8D 8C 8B 8A 89 88

TCON* Timer 0 and 1 Control 88H TF1 TR1 TF0 TR0 - - - - 00H 00000000

2003 Dec 8 16

Philips Semiconductors

User’s Manual - Preliminary -

P89LPC906/907/908GENERAL DESCRIPTION

Name Description

TH0 Timer 0 High 8CH 00H 00000000

TH1 Timer 1 High 8DH 00H 00000000

TL0 Timer 0 Low 8AH 00H 00000000

TL1 Timer 1 Low 8BH 00H 00000000

TMOD Timer 0 and 1 Mode 89H - - T1M1 T1M0 - - T0M1 T0M0 00H 00000000

TRIM# Internal Oscillator Trim Register 96H - ENCLK TRIM.5 TRIM.4 TRIM.3 TRIM.2 TRIM.1 TRIM.0 Notes 4,5

WDCON# Watchdog Control Register A7H PRE2 PRE1 PRE0 - - WDRUN WDTOF WDCLK Notes 3,5

WDL# Watchdog Load C1H FFH 11111111

WFEED1# Watchdog Feed 1 C2H

WFEED2# Watchdog Feed 2 C3H

SFR

Address

MSB

Bit Functions and Addresses Reset Value

LSB

Hex Binary

2003 Dec 8 17

Philips Semiconductors

User’s Manual - Preliminary -

P89LPC906/907/908GENERAL DESCRIPTION

Table 2: Special function registers table - P89LPC907

Name Description

SFR

Address

MSB

E7 E6 E5 E4 E3 E2 E1 E0

ACC* Accumulator E0H 00H 00000000

Bit Functions and Addresses Reset Value

LSB

Hex Binary

AUXR1# Auxiliary Function Register A2H ----SRST0-DPS00H

000000x0

F7 F6 F5 F4 F3 F2 F1 F0

B* B Register F0H 00H 00000000

BRGR0#§ Baud Rate Generator Rate Low BEH 00H 00000000

BRGR1#§ Baud Rate Generator Rate High BFH 00H 00000000

BRGCON#Baud Rate Generator Control BDH------SBRGSBRGEN00Hxxxxxx00

CMP1# Comparator 1 Control Register ACH - - CE1 - CN1 OE1 CO1 CMF1 00H

xx000000

DIVM# CPU Clock Divide-by-M Control 95H 00H 00000000

DPTR Data Pointer (2 bytes)

DPH Data Pointer High 83H 00H 00000000

DPL Data Pointer Low 82H 00H 00000000

FMADRH# Program Flash Address High E7H 00H 00000000

FMADRL# Program Flash Address Low E6H 00H 00000000

FMCON#

Program Flash Control (Read)

Program Flash Control (Write)

E4H

BUSY - - - HVA HVE SV OI 70H 01110000

FMCMD.7FMCMD.6FMCMD.5FMCMD.4FMCMD.3FMCMD.2FMCMD.1FMCMD.

FMDATA# Program Flash Data E5H 00H 00000000

IEN0* Interrupt Enable 0 A8H EA EWDRT EBO ES ET1 - ET0 - 00H 00000000

EF EE ED EC EB EA E9 E8

IEN1*# Interrupt Enable 1 E8H - EST - - - EC EKBI - 00H

BF BE BD BC BB BA B9 B8

IP0* Interrupt Priority 0 B8H - PWDRT PBO PS PT1 - PT0 - 00H

IP0H# Interrupt Priority 0 High B7H -

PWDRT

PBOH PSH PT1H - PT0H - 00H

FF FE FD FC FB FA F9 F8

IP1*# Interrupt Priority 1 F8H - PST - - - PC PKBI - 00H

IP1H# Interrupt Priority 1 High F7H - PSTH - - - PCH PKBIH - 00H

KBCON#Keypad Control Register 94H------

PATN_S

KBIF 00H

2003 Dec 8 18

00x00000

x0000000

00x00000

xxxxxx00

Philips Semiconductors

User’s Manual - Preliminary -

P89LPC906/907/908GENERAL DESCRIPTION

Name Description

SFR

Address

MSB

Bit Functions and Addresses Reset Value

LSB

Hex Binary

KBMASK# Keypad Interrupt Mask Register 86H 00H 00000000

KBPATN# Keypad Pattern Register 93H FFH 11111111

87 86 85 84 83 82 81 80

P0* Port 0 80H -

KB6

CMPREF/

KB5

CIN1A/

KB4

-KB2-KB0 Note 1

CMP1/

97 96 95 94 93 92 91 90

P1* Port 1 90H - - RST

--T0-TxD

B7 B6 B5 B4 B3 B2 B1 B0

P0M1# Port 0 Output Mode 1 84H - (P0M1.6) (P0M1.5) (P0M1.4) - (P0M1.2) - (P0M1.0) FFH 11111111

P0M2# Port 0 Output Mode 2 85H - (P0M2.6) (P0M2.5) (P0M2.4) - (P0M2.2) - (P0M2.0) 00H 00000000

P1M1# Port 1 Output Mode 1 91H - - (P1M1.5) - - (P1M1.2) - (P1M1.0) FFH

P1M2# Port 1 Output Mode 2 92H - - (P1M2.5) - - (P1M2.2) - (P1M2.0) 00H

11111111

00000000

PCON# Power Control Register 87H SMOD1 SMOD0 BOPD BOI GF1 GF0 PMOD1 PMOD0 00H 00000000

PCONA# Power Control Register A B5H RTCPD VCPD - SPD

00H

00000000

D7 D6 D5 D4 D3 D2 D1 D0

PSW* Program Status Word D0H CY AC F0 RS1 RS0 OV F1 P 00H 00000000

PT0AD#Port 0 Digital Input Disable F6H--PT0AD.5PT0AD.4----00Hxx00000x

RSTSRC# Reset Source Register DFH - - BOF POF - R_WD R_SF R_EX Note 2

1,5

RTCCON# Real-Time Clock Control D1H RTCF RTCS1 RTCS0 - - - ERTC RTCEN 60H

RTCH# Real-Time Clock Register High D2H 00H

RTCL# Real-Time Clock Register Low D3H 00H

011xxx00

00000000

SBUF Serial Port Data Buffer Register 99H xxH xxxxxxxx

9F 9E 9D 9C 9B 9A 99 98

SCON* Serial Port Control 98H SM0 SM1 SM2 - TB8 - TI - 00H 00000000

SSTAT# Serial Port Extended Status Register BAH DBMOD INTLO CIDIS DBISEL ----00H00000000

SP Stack Pointer 81H 07H 00000111

TAMOD# Timer 0 Auxiliary Mode 8FH -------T0M200Hxxx0xxx0

8F 8E 8D 8C 8B 8A 89 88

TCON*Timer 0 and 1 Control 88HTF1TR1TF0TR0----00H00000000

2003 Dec 8 19

Philips Semiconductors

User’s Manual - Preliminary -

P89LPC906/907/908GENERAL DESCRIPTION

Name Description

TH0 Timer 0 High 8CH 00H 00000000

TH1 Timer 1 High 8DH 00H 00000000

TL0 Timer 0 Low 8AH 00H 00000000

TL1 Timer 1 Low 8BH 00H 00000000

TMOD Timer 0 and 1 Mode 89H - - T1M1 T1M0 - - T0M1 T0M0 00H 00000000

TRIM# Internal Oscillator Trim Register 96H - - TRIM.5 TRIM.4 TRIM.3 TRIM.2 TRIM.1 TRIM.0 Notes 4,5

WDCON# Watchdog Control Register A7H PRE2 PRE1 PRE0 - - WDRUN WDTOF WDCLK Notes 3,5

WDL# Watchdog Load C1H FFH 11111111

WFEED1# Watchdog Feed 1 C2H

WFEED2# Watchdog Feed 2 C3H

SFR

Address

MSB

Bit Functions and Addresses Reset Value

LSB

Hex Binary

2003 Dec 8 20

Philips Semiconductors

User’s Manual - Preliminary -

P89LPC906/907/908GENERAL DESCRIPTION

Table 3: Special function registers table - P89LPC908

Name Description

SFR

Address

MSB

E7 E6 E5 E4 E3 E2 E1 E0

ACC* Accumulator E0H 00H 00000000

Bit Functions and Addresses Reset Value

LSB

Hex Binary

AUXR1# Auxiliary Function Register A2H - EBRR - - SRST 0 - DPS 00H

000000x0

F7 F6 F5 F4 F3 F2 F1 F0

B* B Register F0H 00H 00000000

BRGR0#§ Baud Rate Generator Rate Low BEH 00H 00000000

BRGR1#§ Baud Rate Generator Rate High BFH 00H 00000000

BRGCON#Baud Rate Generator Control BDH------SBRGSBRGEN00Hxxxxxx00

CMP1# Comparator 1 Control Register ACH - - CE1 - CN1 OE1 CO1 CMF1 00H

xx000000

DIVM# CPU Clock Divide-by-M Control 95H 00H 00000000

DPTR Data Pointer (2 bytes)

DPH Data Pointer High 83H 00H 00000000

DPL Data Pointer Low 82H 00H 00000000

FMADRH# Program Flash Address High E7H 00H 00000000

FMADRL# Program Flash Address Low E6H 00H 00000000

FMCON#

Program Flash Control (Read)

Program Flash Control (Write)

E4H

BUSY - - - HVA HVE SV OI 70H 01110000

FMCMD.7FMCMD.6FMCMD.5FMCMD.4FMCMD.3FMCMD.2FMCMD.1FMCMD.

FMDATA# Program Flash Data E5H 00H 00000000

IEN0* Interrupt Enable 0 A8H EA EWDRT EBO ES/ESR ET1 - ET0 - 00H 00000000

EF EE ED EC EB EA E9 E8

IEN1*# Interrupt Enable 1 E8H - EST - - - EC EKBI - 00H

BF BE BD BC BB BA B9 B8

IP0* Interrupt Priority 0 B8H - PWDRT PBO PS/PSR PT1 - PT0 - 00H

IP0H# Interrupt Priority 0 High B7H -

PWDRT

PBOH

PSH/

PSRH

PT1H - PT0H - 00H

FF FE FD FC FB FA F9 F8

IP1*# Interrupt Priority 1 F8H - PST - - - PC PKBI - 00H

IP1H# Interrupt Priority 1 High F7H - PSTH - - - PCH PKBIH - 00H

KBCON#Keypad Control Register 94H------

PATN_S

KBIF 00H

2003 Dec 8 21

00x00000

x0000000

00x00000

xxxxxx00

Philips Semiconductors

User’s Manual - Preliminary -

P89LPC906/907/908GENERAL DESCRIPTION

Name Description

SFR

Address

MSB

Bit Functions and Addresses Reset Value

LSB

Hex Binary

KBMASK# Keypad Interrupt Mask Register 86H 00H 00000000

KBPATN# Keypad Pattern Register 93H FFH 11111111

87 86 85 84 83 82 81 80

P0* Port 0 80H -

KB6

CMPREF/

KB5

CIN1A/

KB4

-KB2- - Note 1

CMP1/

97 96 95 94 93 92 91 90

P1* Port 1 90H - - RST

---RxDTxD

P0M1# Port 0 Output Mode 1 84H - (P0M1.6) (P0M1.5) (P0M1.4) - (P0M1.2) - - FFH 11111111

P0M2# Port 0 Output Mode 2 85H - (P0M2.6) (P0M2.5) (P0M2.4) - (P0M2.2) - - 00H 00000000

P1M1# Port 1 Output Mode 1 91H - - (P1M1.5) - - - (P1M1.1) (P1M1.0) FFH

P1M2# Port 1 Output Mode 2 92H - - (P1M2.5) - - - (P1M2.1) (P1M2.0) 00H

11111111

00000000

PCON# Power Control Register 87H SMOD1 SMOD0 BOPD BOI GF1 GF0 PMOD1 PMOD0 00H 00000000

PCONA# Power Control Register A B5H RTCPD VCPD - SPD

00H

00000000

D7 D6 D5 D4 D3 D2 D1 D0

PSW* Program Status Word D0H CY AC F0 RS1 RS0 OV F1 P 00H 00000000

PT0AD# Port 0 Digital Input Disable F6H - - PT0AD.5 PT0AD.4 - PT0AD.2 - - 00H xx00000x

RSTSRC# Reset Source Register DFH - - BOF POF R_BK R_WD R_SF R_EX Note 2

1,5

RTCCON# Real-Time Clock Control D1H RTCF RTCS1 RTCS0 - - - ERTC RTCEN 60H

RTCH# Real-Time Clock Register High D2H 00H

RTCL# Real-Time Clock Register Low D3H 00H

011xxx00

00000000

SADDR# Serial Port Address Register A9H 00H 00000000

SADEN# Serial Port Address Enable B9H 00H 00000000

SBUF Serial Port Data Buffer Register 99H xxH xxxxxxxx

9F 9E 9D 9C 9B 9A 99 98

SCON* Serial Port Control 98H SM0/FE SM1 SM2 REN TB8 RB8 TI RI 00H 00000000

SSTAT# Serial Port Extended Status Register BAH DBMOD INTLO CIDIS DBISEL FE BR OE STINT 00H 00000000

SP Stack Pointer 81H 07H 00000111

8F 8E 8D 8C 8B 8A 89 88

TCON*Timer 0 and 1 Control 88HTF1TR1TF0TR0----00H00000000

TH0 Timer 0 High 8CH 00H 00000000

TH1 Timer 1 High 8DH 00H 00000000

2003 Dec 8 22

Philips Semiconductors

User’s Manual - Preliminary -

P89LPC906/907/908GENERAL DESCRIPTION

Name Description

TL0 Timer 0 Low 8AH 00H 00000000

TL1 Timer 1 Low 8BH 00H 00000000

TMOD Timer 0 and 1 Mode 89H - - T1M1 T1M0 - - T0M1 T0M0 00H 00000000

TRIM# Internal Oscillator Trim Register 96H - - TRIM.5 TRIM.4 TRIM.3 TRIM.2 TRIM.1 TRIM.0 Notes 4,5

WDCON# Watchdog Control Register A7H PRE2 PRE1 PRE0 - - WDRUN WDTOF WDCLK Notes 3,5

WDL# Watchdog Load C1H FFH 11111111

WFEED1# Watchdog Feed 1 C2H

WFEED2# Watchdog Feed 2 C3H

SFR

Address

MSB

Bit Functions and Addresses Reset Value

LSB

Hex Binary

Notes:

* SFRs are bit addressable. # SFRs are modified from or added to the 80C51 SFRs.

- Reserved bits, must be written with 0’s.

§ BRGR1 and BRGR0 must only be written if BRGEN in BRGCON SFR is ’0’. If any of them is written if BRGEN = 1, result is unpredictable.

Unimplemented bits in SFRs (labeled ’-’ ) are X (unknown) at all times. Unless otherwise specified, ones should not be written to

these bits since they may be used for other purposes in future derivatives. The reset values shown for these bits are ’0’s although they are unknown when read.

1. All ports are in input only (high impendance) state after power-up.

2. The RSTSRC register reflects the cause of theP89LPC906/907/908 reset. Upon a power-up reset, all reset source flags are cleared except POF and BOF - the power-on reset value is xx110000.

3. After reset, the value is 111001x1, i.e., PRE2-PRE0 are all 1, WDRUN=1 and WDCLK=1. WDTOF bit is 1 after watchdog reset and is 0 after power-on reset. Other resets will not affect WDTOF.

4. On power-on reset, the TRIM SFR is initialized with a factory preprogrammed value. Other resets will not cause initialization of the TRIM register.

5. The only reset source that affects these SFRs is power-on reset.

2003 Dec 8 23

Philips Semiconductors

MEMORY ORGANIZATION

The P89LPC906/907/908 memory map is shown in Figure 1-1.

03FFh

Sector 3

0300h 02FFh

Sector 2

0200h 01FFh

Sector 1

0100h

00FFh

Sector 0

0000h

1 KB Flash Code

Memory Space

Special Function

Registers

(directly addressable)

DATA

128 Bytes On-Chip

Data Memory (stack,

direct and indir. addr.)

4 Reg. Banks R0-R7

Data Memory

(DATA, IDATA)

User’s Manual - Preliminary -

P89LPC906/907/908GENERAL DESCRIPTION

FFh

80h 7Fh

00h

Figure 1-1: P89LPC906/907/908 Memory Map

The various P89LPC906/907/908 memory spaces are as follows:

DATA 128 bytes of internal data memory space (00h..7Fh) accessed via direct or indirect addressing, using instructions

other than MOVX and MOVC.

SFR Special Function Registers. Selected CPU registers and peripheral control and status registers, accessible only via

direct addressing.

CODE 1KB of Code memory accessed as part of program execution and via the MOVC instruction.

2003 Dec 8 24

Philips Semiconductors

User’s Manual - Preliminary -

CLOCKS

P89LPC906/907/908

2. CLOCKS

ENHANCED CPU

The P89LPC906/907/908 uses an enhanced 80C51 CPU which runs at 6 times the speed of standard 80C51 devices. A machine cycle consists of two CPU clock cycles, and most instructions execute in one or two machine cycles.

CLOCK DEFINITIONS

The P89LPC906/907/908 device has several internal clocks as defined below:

• OSCCLK - Input to the DIVM clock divider. OSCCLK is selected from one of the clock sources (see Figure 2-3,Figure 2-4,) and

can also be optionally divided to a slower frequency (see section "CPU Clock (CCLK) Modification: DIVM Register"). Note: f

is defined as the OSCCLK frequency.

OSC

• XCLK - Output of the crystal oscillator (P89LPC906)

• CCLK - CPU clock .

• PCLK - Clock for the various peripheral devices and is CCLK/2

CPU CLOCK (OSCCLK)

The P89LPC906 provides several user-selectable oscillator options. This allows optimization for a range of needs from high precision to lowest possible cost. These options are configured when the FLASH is programmed and include an on-chip watchdog oscillator, an on-chip RC oscillator, an oscillator using an external crystal, or an external clock source. The crystal oscillator can be optimized for low, medium, or high frequency crystals covering a range from 20 kHz to 12 MHz.

The P89LPC907 and P89LPC908 devices allow the user to select between an on-chip watchdog oscillator and an on-chip RC oscillator as the CPU clock source.

LOW SPEED OSCILLATOR OPTION - P89LPC906

This option supports an external crystal in the range of 20 kHz to 100 kHz. Ceramic resonators are also supported in this configuration.

MEDIUM SPEED OSCILLATOR OPTION - P89LPC906

This option supports an external crystal in the range of 100 kHz to 4 MHz. Ceramic resonators are also supported in this configuration.

HIGH SPEED OSCILLATOR OPTION - P89LPC906

This option supports an external crystal in the range of 4MHz to 12 MHz. Ceramic resonators are also supported in this configuration. If CCLK is 8MHz or slower, the CLKLP SFR bit (AUXR1.7) can be set to ’1’ to reduce power consumption. On reset, CLKLP is ’0’ allowing highest performance access. This bit can then be set in software if CCLK is running at 8MHz or slower.

2003 Dec 8 25

Philips Semiconductors

User’s Manual - Preliminary -

CLOCKS

Quartz crystal or

ceramic resonator

The oscillator must be configured in one of the following modes:

- Low Frequency Crystal

- Medium Frequency Crystal

- High Frequency Crystal

* A series resistor may be required to limit crystal drive levels. This is especially important for low frequency crystals.

Figure 2-1: Using the Crystal Oscillator - P89LPC906

P89LPC906/907/908

P89LPC906

XTAL1

XTAL2

OSCILLATOR OPTION SELECTION- P89LPC906

The oscillator option is selectable either by the FOSC2:0 bits in UCFG1 or by the RTCS1:0 bits in RTCCON. If the FOSC2:0 bits select an OSCCLK source of either the internal RC oscillator or the WDT oscillator, then the RTCS1:0 bits will select the oscillator option for the crystal oscillator. Otherwise, the crystal oscillator option is selected by FOSC2:0. See Table 6-1 and Table 6-2.

CLOCK OUTPUT - P89LPC906

The P89LPC906 supports a user selectable clock output function on the XTAL2 / CLKOUT pin when no crystal oscillator is being used. This condition occurs if another clock source has been selected (on-chip RC oscillator, watchdog oscillator, external clock input on X1) and if the Real-Time clock is not using the crystal oscillator as its clock source. This allows external devices to synchronize to the P89LPC906. This output is enabled by the ENCLK bit in the TRIM register

The frequency of this clock output is 1/2 that of the CCLK. If the clock output is not needed in Idle mode, it may be turned off prior to entering Idle, saving additional power. Note: on reset, the TRIM SFR is initialized with a factory preprogrammed value. Therefore when setting or clearing the ENCLK bit, the user should retain the contents of bits 5:0 of the TRIM register. This can be done by reading the contents of the TRIM register (into the ACC for example), modifying bit 6, and writing this result back into the TRIM register. Alternatively, the "ANL direct" or "ORL direct" instructions can be used to clear or set bit 6 of the TRIM register.Increasing the TRIM value will decrease the oscillator frequency.

ON-CHIP RC OSCILLATOR OPTION

The P89LPC906/907/908 has a 6-bit field within the TRIM register that can be used to tune the frequency of the RC oscillator. During reset, the TRIM value is initialized to a factory pre-programmed value to adjust the oscillator frequency to 7.373 MHz, ±1%. (Note: the initial value is better than 1%; please refer to the datasheet for behavior over temperature). End user applications can write to the TRIM register to adjust the on-chip RC oscillator to other frequencies. Increasing the TRIM value will decrease the oscillator frequency.

If CCLK is 8MH or slower, the CLKLP SFR bit (AUXR1.7) can be set to ’1’ to reduce power consumption. On reset, CLKLP is ’0’ allowing highest performance access. This bit can then be set in software if CCLK is running at 8MHz or slower

WATCHDOG OSCILLATOR OPTION

The watchdog has a separate oscillator which has a nominal frequency of 400KHz. This oscillator can be used to save power when a high clock frequency is not needed.

2003 Dec 8 26

Philips Semiconductors

User’s Manual - Preliminary -

CLOCKS

P89LPC906/907/908

EXTERNAL CLOCK INPUT OPTION - P89LPC906

In this configuration, the processor clock is derived from an external source driving the XTAL1 / P3.1 pin. The rate may be from 0 Hz up to 12 MHz. The XTAL2 / P3.0 pin may be used as a standard port pin or a clock output.

TRIM

Address: 96h

Not bit addressable

Reset Source(s): Power-up only

Reset Value: On power-up reset, ENCLK = 0, and TRIM.5-0 are loaded with the factory programmed value.

BIT SYMBOL FUNCTION

TRIM.7 - Reserved.

TRIM.6 ENCLK When ENCLK =1, CCLK/ 2 is output on the XTAL2 pin (P3.0) provided that the crystal

TRIM.5-0 Trim value.

Note: on reset, the TRIM SFR is initialized with a factory preprogrammed value. When setting or clearing the ENCLK bit, the user should retain the contents of bits 5:0 of the TRIM register. This can be done by reading the contents of the TRIM register (into the ACC for example), modifying bit 6, and writing this result back into the TRIM register. Alternatively, the "ANL direct" or "ORL direct" instructions can be used to clear or set bit 6 of the TRIM register.

76543210

- ENCLK TRIM.5 TRIM.4 TRIM.3 TRIM.2 TRIM.1 TRIM.0

oscillator is not being used. When ENCLK=0, no clock output is enabled (P89LPC906).

Figure 2-2: On-Chip RC Oscillator TRIM Register

CPU CLOCK (CCLK) WAKEUP DELAY

The P89LPC906/907/908 has an internal wakeup timer that delays the clock until it stabilizes depending to the clock source used. If the clock source is any of the three crystal selections (P89LPC906), the delay is 992 OSCCLK cycles plus 60-100µs. If the clock source is either the internal RC oscillator or the Watchdog oscillator, the delay is 224 OSCCLK cycles plus 60-100µs.

CPU CLOCK (CCLK) MODIFICATION: DIVM REGISTER

The OSCCLK frequency can be divided down, by an integer, up to 510 times by configuring a dividing register, DIVM, to provide CCLK. This produces the CCLK frequency using the following formula:

CCLK frequency = f

Where: f

Since N ranges from 0 to 255, the CCLK frequency can be in the range of f

This feature makes it possible to temporarily run the CPU at a lower rate, reducing power consumption. By dividing the clock, the CPU can retain the ability to respond to events other than those that can cause interrupts (i.e. events that allow exiting the Idle mode) by executing its normal program at a lower rate. This can often result in lower power consumption than in Idle mode. This can allow bypassing the oscillator start-up time in cases where Power down mode would otherwise be used. The value of DIVM may be changed by the program at any time without interrupting code execution.

is the frequency of OSCCLK

OSC

N is the value of DIVM.

OSC

/ (2N)

OSC

to f

/510 ( for N =0, CCLK = f

OSC

) .

2003 Dec 8 27

Philips Semiconductors

User’s Manual - Preliminary -

CLOCKS

P89LPC906/907/908

LOW POWER SELECT (P89LPC906)

The P89LPC906 is designed to run at 12MHz (CCLK) maximum. However, if CCLK is 8MHz or slower, the CLKLP SFR bit (AUXR1.7) can be set to a ’1’ to lower the power consumption further. On any reset, CLKLP is ’0’ allowing highest performance. This bit can then be set in software if CCLK is running at 8MHz or slower.

RTCS1:0

XTAL1

XTAL2

RC Oscillator

(7.3728MHz)

Watchdog

Oscillator

High freq.

Med freq.

Low freq.

FOSC2:0

OSC

CLK

Oscillator

Clock

DIVM

CPU

Clock

RTC

CCLK

CPU

PCLK

WDT

(400KHz)

Timer 0 & 1

Figure 2-3: Block Diagram of Oscillator Control - P89LPC906

2003 Dec 8 28

Philips Semiconductors

User’s Manual - Preliminary -

CLOCKS

RC Oscillator

(7.3728MHz)

Watchdog

Oscillator

(400KHz)

FOSC2:0

OSC

CLK

DIVM

CPU

Clock

CCLK

P89LPC906/907/908

RTCS1:0

RTC

CPU

WDT

PCLK

Baud rate

UART

Timer 0 & 1

Generator

Figure 2-4: Block Diagram of Oscillator Control- P89LPC907,P89LPC908

2003 Dec 8 29

Philips Semiconductors

User’s Manual - Preliminary -

CLOCKS

P89LPC906/907/908

2003 Dec 8 30

Philips Semiconductors

User’s Manual - Preliminary -

INTERRUPTS

P89LPC906/907/908

3. INTERRUPTS

The P89LPC906/907/908 use a four priority level interrupt structure. This allows great flexibility in controlling the handling of the many interrupt sources. The P89LPC906 supports 6 interrupt sources: timers 0 and 1, brownout detect, watchdog/ realtime clock, keyboard, and the comparator. The P89LPC907 supports 7 interrupt sources: timers 0 and 1, serial port Tx, brownout detect, watchdog/ realtime clock, keyboard, and comparators 1 and 2. The P89LPC908 supports 9 interrupt sources: timers 0 and 1, serial port Tx, serial port Rx, combined serial port Rx/Tx, brownout detect, watchdog/ realtime clock, keyboard, and comparators 1 and 2.

Each interrupt source can be individually enabled or disabled by setting or clearing a bit in the interrupt enable registers IEN0 or IEN1. The IEN0 register also contains a global enable bit, EA, which enables all interrupts.

Each interrupt source can be individually programmed to one of four priority levels by setting or clearing bits in the interrupt priority registers IP0, IP0H, IP1, and IP1H. An interrupt service routine in progress can be interrupted by a higher priority interrupt, but not by another interrupt of the same or lower priority. The highest priority interrupt service cannot be interrupted by any other interrupt source. If two requests of different priority levels are pending at the start of an instruction, the request of higher priority level is serviced.

If requests of the same priority level are pending at the start of an instruction, an internal polling sequence determines which request is serviced. This is called the arbitration ranking. Note that the arbitration ranking is only used to resolve pending requests of the same priority level.

Table summarizes the interrupt sources, flag bits, vector addresses, enable bits, priority bits, arbitration ranking, and whether each interrupt may wake up the CPU from a Power down mode.

INTERRUPT PRIORITY STRUCTURE

There are four SFRs associated with the four interrupt levels: IP0, IP0H, IP1, IP1H. Every interrupt has two bits in IPx and IPxH (x = 0,1) and can therefore be assigned to one of four levels, as shown in Table .

Table 3-1: Interrupt priority level

Priority Bits

IPxH IPx

0 0 Level 0 (lowest priority)

0 1 Level 1

1 0 Level 2

1 1 Level 3 (highest priority)

Table 3-2: Summary of Interrupts - P89LPC906

Description

Timer 0 Interrupt TF0 000Bh ET0 (IEN0.1) IP0H.1, IP0.1 3 No

Timer 1 Interrupt TF1 001Bh ET1 (IEN0.3) IP0H.3, IP0.3 5 No

Brownout Detect BOF 002Bh EBO (IEN0.5) IP0H.5, IP0.5 1 Yes

Watchdog Timer/Realtime Clock

KBI Interrupt KBIF 003Bh EKBI (IEN1.1) IP1H.1, IP1.1 4 Yes

Comparator interrupt CMF 0043h EC (IEN1.2) IP1H.2, IP1.2 6 Yes

Interrupt

Flag Bit(s)

WDOVF/

RTCF

Vector

Address

0053h

Interrupt

Enable Bit(s)

EWDRT

(IEN0.6)

Interrupt Priority Level

Interrupt

Priority

IP0H.6, IP0.6 2 Yes

Arbitration

Ranking

Power down

Wakeup

2003 Dec 8 31

Philips Semiconductors

User’s Manual - Preliminary -

INTERRUPTS

Table 3-3: Summary of Interrupts - P89LPC907,P89LPC908

Description

Timer 0 Interrupt TF0 000Bh ET0 (IEN0.1) IP0H.1, IP0.1 3 No

Timer 1 Interrupt TF1 001Bh ET1 (IEN0.3) IP0H.3, IP0.3 5 No

Serial Port Tx and Rx

Serial Port Rx

Brownout Detect BOF 002Bh EBO (IEN0.5) IP0H.5, IP0.5 1 Yes

Watchdog Timer/Realtime Clock

KBI Interrupt KBIF 003Bh EKBI (IEN1.1) IP1H.1, IP1.1 4 Yes

Comparator interrupt CMF 0043h EC (IEN1.2) IP1H.2, IP1.2 6 Yes

Serial Port Tx

1. SSTAT.5 = 0 selects combined Serial Port (UART) Tx and Rx interrupt; SSTAT.5 = 1 selects Serial Port Rx interrupt only (Tx interrupt will be different, see Note 3 below).

2. This interrupt is used as Serial Port (UART) Tx interrupt if and only if SSTAT.5 = 1, and is disabled otherwise. Although the P89LPC907 does not have the RxD pin, this function is still available to allow switching the Tx interrupt vector.

3. If SSTAT.0 = 1, the following Serial Port additional flag bits can cause this interrupt: FE, BR, OE

1,3

Interrupt

Flag Bit(s)

TI & RI

WDOVF/

RTCF

TI 006Bh EST (IEN1.6) P1H.6, IP1.6 7 No

Vector

Address

0023h

0053h

Interrupt

Enable Bit(s)

ES/ESR (IEN0.4)

EWDRT (IEN0.6)

Interrupt

Priority

IP0H.4, IP0.4 8 No

IP0H.6, IP0.6 2 Yes

P89LPC906/907/908

Arbitration

Ranking

Power down

Wakeup

EXTERNAL INTERRUPT INPUTS

The P89LPC906/907/908 have a Keypad Interrupt function (see Keypad Interrupt (KBI) on page 77). This can be used as an external interrupt input. If enabled when the P89LPC906/907/908 is put into Power down or Idle mode, the keypad interrupt will cause the processor to wake up and resume operation. Refer to the section on Power Reduction Modes for details.

EXTERNAL INTERRUPT PIN GLITCH SUPPRESSION

Most of the P89LPC906/907/908 pins have glitch suppression circuits to reject short glitches (please refer to the P89LPC906/ 907/908 datasheet, AC Electrical Characteristics for glitch filter specifications) .

2003 Dec 8 32

Philips Semiconductors

User’s Manual - Preliminary -

INTERRUPTS

RTCF ERTC

(RTCCON.1)

WDOVF

BOPD

EBO

KBIF EKBI

EWDRT

CMF

EA (IE0.7)

TF1

ET1

TF0

ET0

P89LPC906/907/908

Wakeup (if in Power down)

Interrupt to CPU

Figure 3-1: Interrupt sources, enables, and Power down Wake-up sources - P89LPC906

BOPD

EBO

RTCF ERTC

(RTCCON.1)

WDOVF

KBIF EKBI

EWDRT

CMF

EA (IE0.7)

TF1

ET1

TI & RI/RI

ES/ESR

EST

TF0

ET0

Figure 3-2: Interrupts sources, enables, and Power down Wake-up sources - P89LPC907,P89LPC908

Wakeup (if in Power down)

Interrupt to CPU

2003 Dec 8 33

Philips Semiconductors

User’s Manual - Preliminary -

INTERRUPTS

P89LPC906/907/908

2003 Dec 8 34

Philips Semiconductors

User’s Manual - Preliminary -

I/O PORTS

P89LPC906/907/908

4. I/O PORTS

The P89LPC906/907/908 has between 3 and 6 I/O pins. The exact number of I/O pins available depends on the clock and reset options chosen:

Table 4-1: Number of I/O Pins Available

Number of I/O

Clock Source Reset Option

On-chip oscillator or watchdog

oscillator

External clock input

(P89LPC906)

Low/medium/high speed oscillator

(external crystal or resonator)

(P89LPC906)

PORT CONFIGURATIONS

No external reset(except during power-up) 6

External RST pin supported 5

No external reset(except during power-up) 5

External RST

No external reset(except during power-up) 4

External RST

pin supported 4

pin supported 3

Pins

8-Pin Package

All but one I/O port pin on the P89LPC906/907/908 may be configured by software to one of four types on a pin-by-pin basis, as shown in Table 4-2. These are: quasi-bidirectional (standard 80C51 port outputs), push-pull, open drain, and input-only. Two configuration registers for each port select the output type for each port pin. P1.5 (RST configured.

Table 4-2: Port Output Configuration Settings

PxM1.y PxM2.y Port Output Mode

0 0 Quasi-bidirectional

0 1 Push-Pull

1 0 Input Only (High Impedance)

11 Open Drain

) can only be an input and cannot be

QUASI-BIDIRECTIONAL OUTPUT CONFIGURATION

Quasi-bidirectional outputs can be used both as an input and output without the need to reconfigure the port. This is possible because when the port outputs a logic high, it is weakly driven, allowing an external device to pull the pin low. When the pin is driven low, it is driven strongly and able to sink a large current. There are three pullup transistors in the quasi-bidirectional output that serve different purposes.

One of these pullups, called the "very weak" pullup, is turned on whenever the port latch for the pin contains a logic 1. This very weak pullup sources a very small current that will pull the pin high if it is left floating.

A second pullup, called the "weak" pullup, is turned on when the port latch for the pin contains a logic 1 and the pin itself is also at a logic 1 level. This pullup provides the primary source current for a quasi-bidirectional pin that is outputting a 1. If this pin is pulled low by an external device, this weak pullup turns off, and only the very weak pullup remains on. In order to pull the pin low under these conditions, the external device has to sink enough current to overpower the weak pullup and pull the port pin below its input threshold voltage.

2003 Dec 8 35

Philips Semiconductors

User’s Manual - Preliminary -

I/O PORTS

The third pullup is referred to as the "strong" pullup. This pullup is used to speed up low-to-high transitions on a quasi-bidirectional port pin when the port latch changes from a logic 0 to a logic 1. When this occurs, the strong pullup turns on for two CPU clocks quickly pulling the port pin high .

The quasi-bidirectional port configuration is shown in Figure 4-1.

Although the P89LPC906/907/908 is a 3V device the pins are 5V-tolerant (except for XTAL1 and XTAL2). If 5V is applied to a pin configured in quasi-bidirectional mode, there will be a current flowing from the pin to VDD causing extra power consumption. Therefore, applying 5V to pins configured in quasi-bidirectional mode is discouraged.

A quasi-bidirectional port pin has a Schmitt-triggered input that also has a glitch suppression circuit. (Please refer to the P89LPC906/907/908 datasheet, AC Characteristics for glitch filter specifications)

port latch data

2 CPU

clock delay

strong

P89LPC906/907/908

very weak

weak

port pin

input data

Figure 4-1: Quasi-Bidirectional Output

glitch rejection

OPEN DRAIN OUTPUT CONFIGURATION

The open drain output configuration turns off all pullups and only drives the pulldown transistor of the port pin when the port latch contains a logic 0. To be used as a logic output, a port configured in this manner must have an external pullup, typically a resistor tied to VDD. The pulldown for this mode is the same as for the quasi-bidirectional mode.

The open drain port configuration is shown in Figure 4-2.

An open drain port pin has a Schmitt-triggered input that also has a glitch suppression circuit (please refer to the P89LPC906/ 907/908 datasheet, AC Characteristics for glitch filter specifications).

port pin

port latch data

input data

glitch rejection

Figure 4-2: Open Drain Output

2003 Dec 8 36

Philips Semiconductors

User’s Manual - Preliminary -

I/O PORTS

P89LPC906/907/908

INPUT-ONLY CONFIGURATION

The input port configuration is shown in Figure 4-3. It is a Schmitt-triggered input that also has a glitch suppression circuit (please refer to the P89LPC906/907/908 datasheet, AC Characteristics for glitch filter specifications)

input data

glitch rejection

Figure 4-3: Input Only

port pin

PUSH-PULL OUTPUT CONFIGURATION

The push-pull output configuration has the same pulldown structure as both the open drain and the quasi-bidirectional output modes, but provides a continuous strong pullup when the port latch contains a logic 1. The push-pull mode may be used when more source current is needed from a port output.

The push-pull port configuration is shown in Figure 4-4.

A push-pull port pin has a Schmitt-triggered input that also has a glitch suppression circuit (please refer to the P89LPC906/907/ 908 datasheet, AC Characteristics for glitch filter specifications)

strong

port latch data

input data

Figure 4-4: Push-Pull Output

port pin

glitch rejection

PORT 0 ANALOG FUNCTIONS

The P89LPC906/907/908 incorporates an analog comparator. In order to give the best analog performance and minimize power consumption, pins that are being used for analog functions must have both the digital outputs and digital inputs disabled.

Digital outputs are disabled by putting the port pins into the input-only mode as described in the Port Configurations section (see Table 4-2).

Digital inputs on Port 0 may be disabled through the use of the PT0AD register. On any reset, the PT0AD bits default to ’0’s to enable digital functions.

2003 Dec 8 37

Philips Semiconductors

User’s Manual - Preliminary -

I/O PORTS

Table 4-3: Port Output Configuration - P89LPC906

Port

P0.4 P0M1.4 P0M2.4 KBI4,CIN1A

P0.6 P0M1.6 P0M2.6 KBI6,CMP1

P1.5 not configurable RST

P3.0 P3M1.0 P3M2.0 XTAL2,CLKOUT

P3.1 P3M1.1 P3M2.1 XTAL1

Table 4-4: Port Output Configuration - P89LPC907

Port

P0.4 P0M1.4 P0M2.4 KBI4,CIN1A

P0.6 P0M1.6 P0M2.6 KBI6,CMP1

P1.0 P1M1.0 P1M2.0 TxD

P1.2 P1M1.2 P1M2.2 T0

P1.5 not configurable RST

Configuration SFR Bits

PxM1.y PxM2.y

Configuration SFR Bits

PxM1.y PxM2.y

Alternate Usage Notes

P89LPC906/907/908

Refer to section "Port 0 Analog Functions" for usage as

analog inputs CIN1A and CMPREF.P0.5 P0M1.5 P0M2.5 KBI5,CMPREF

Input only. Usage as general purpose input or RST is

determined by User Configuration Bit RPD (UCFG1.6).

Always a reset input during a power-on sequence.

Refer to section "Port 0 Analog Functions" for usage as

analog inputs CIN1A and CMPREF.P0.5 P0M1.5 P0M2.5 KBI5,CMPREF

Input only. Usage as general purpose input or RST is

determined by User Configuration Bit RPD (UCFG1.6).

Always a reset input during a power-on sequence.

Table 4-5: Port Output Configuration - P89LPC908

Port

P0.4 P0M1.4 P0M2.4 KBI4,CIN1A

P0.6 P0M1.6 P0M2.6 KBI6,CMP1

P1.0 P1M1.0 P1M2.0 TxD

P1.1 P1M1.1 P1M2.1 RxD

P1.5 not configurable RST

Configuration SFR Bits

PxM1.y PxM2.y

Alternate Usage Notes

Refer to section "Port 0 Analog Functions" for usage as

analog inputs CIN1A and CMPREF.P0.5 P0M1.5 P0M2.5 KBI5,CMPREF

Input only. Usage as general purpose input or RST is

determined by User Configuration Bit RPD (UCFG1.6).

Always a reset input during a power-on sequence.

Table 4-6: Additional Port Features

After power-up, all pins are in Input-Only mode. Please note that this is different from the LPC76x series of devices.

• After power-up, all I/O pins except P1.5, may be configured by software.

• Pin P1.5 is input only.

• Every output on the P89LPC906/907/908 has been designed to sink typical LED drive current. However, there is a maximum total output current for all ports which must not be exceeded. Please refer to the P89LPC906/907/908 datasheet for detailed specifications.

2003 Dec 8 38

Philips Semiconductors

User’s Manual - Preliminary -

I/O PORTS

All ports pins that can function as an output have slew rate controlled outputs to limit noise generated by quickly switching output signals. The slew rate is factory-set to approximately 10 ns rise and fall times.

P89LPC906/907/908

2003 Dec 8 39

Philips Semiconductors

User’s Manual - Preliminary -

I/O PORTS

P89LPC906/907/908

2003 Dec 8 40

Philips Semiconductors

User’s Manual - Preliminary -

TIMERS 0 AND 1

P89LPC906/907/908

5. TIMERS 0 AND 1

The P89LPC906/907/908 has two general-purpose counter/timers which are similar to the 80C51 Timer 0 and Timer 1. Timer 0 of the P89LPC907 can be configured to operate either as a timer or event counter (see Figure 5-1). An option to automatically toggle the T0 pin upon timer overflow has been added. Timer 1 of the P89LPC907 and both Timer 0 and Timer 1 of the P89LPC906 and P89LPC908 devices may only function as timers.

In the “Timer” function, the timer is incremented every PCLK.

In the “Counter” function, the Timer 0 register is incremented in response to a 1-to-0 transition on the external input pin, T0, which is sampled once during every machine cycle. When the pin is high during one cycle and low in the next cycle, the count is incremented. The new count value appears in the register during the cycle following the one in which the transition was detected. Since it takes 2 machine cycles (4 CPU clocks) to recognize a 1-to-0 transition, the maximum count rate is 1/4 of the CPU clock frequency. There are no restrictions on the duty cycle of the external input signal, but to ensure that a given level is sampled at least once before it changes, it should be held for at least one full machine cycle.

The “Timer” or “Counter” function is selected by control bit T0C/T of the P89LPC906 and P89LPC908, and Timer 1 of the P89LPC907 have four operating modes (modes 0, 1, 2, and 3), which are selected by bit-pairs (TnM1, TnM0) in TMOD. Modes 0, 1, 2 and 3 are the same for both Timers. Mode 3 is different. The operating modes are described later in this section. In addition to these modes, Timer 0 of the P89LPC907 has mode 6. Additionally the T0M2 mode bit in TAMOD is used to specify modes with Timer 0 of the P89LPC907.

TMOD

Address: 89h

Not bit addressable

Reset Source(s): Any source

Reset Value: 00000000B

BIT SYMBOL FUNCTION

TMOD.7 - Reserved.

TMOD.6 - Reserved.

TMOD.5, 4 T1M1,T1M0 Mode Select for Timer 1. These bits are used to determine the Timer 1 mode (see Figure

TMOD.3 - Reserved.

TMOD.2 T0C/T

TMOD.1, 0 T0M1,T0M0 Mode Select for Timer 0. These bits are used to determine the Timer 0 mode (see Figure

76543210

--T1M1T1M0-T0C/T

5-2).

Timer or Counter Selector for Timer 0. Cleared for Timer operation (input from CCLK). Set for Counter operation (input from T0 input pin).P89LPC907. When writing to this register on the P89LPC906 or P89LPC908 devices, this bit position should be written with a zero.

5-2). On the P89LPC907 these bits are used with the T0M2 bit in the TAMOD register to determine the Timer 0 mode (see Figure 5-2).

in the Special Function Register TMOD. Timer 0 and Timer 1

T0M1 T0M0

Figure 5-1: Timer/Counter Mode Control register (TMOD)

2003 Dec 8 41

Philips Semiconductors

User’s Manual - Preliminary -

TIMERS 0 AND 1

TAMOD - P89LPC907

Address: 8Fh

Not bit addressable

Reset Source(s): Any reset

Reset Value: xxx0xxx0B

BIT SYMBOL FUNCTION

TAMOD.7-1 - Reserved for future use. Should not be set to 1 by user programs.

TAMOD.0 T0M2 Mode Select bit 2 for Timer 0. Used with T0M1 and T0M0 in the TMOD register to

TnM2-TnM0

0 0 0 8048 Timer “TLn” serves as 5-bit prescaler. (Mode 0)

0 0 1 16-bit Timer/Counter “THn” and “TLn” are cascaded; there is no prescaler. (Mode 1)

0 1 0 8-bit auto-reload Timer/Counter. THn holds a value which is loaded into TLn when it

0 1 1 Timer 0 is a dual 8-bit Timer/Counter in this mode. TL0 is an 8-bit Timer/Counter controlled

1 0 0 Reserved. User must not configure to this mode.

1 0 1 Reserved. User must not configure to this mode.

1 1 0 PWM mode (see section "Mode 6 - P89LPC907").

1 1 1 Reserved. User must not configure to this mode.

76543210

-------T0M2

determine Timer 0 mode (P89LPC907).

Timer Mode

overflows. (Mode 2)

by the standard Timer 0 control bits. TH0 is an 8-bit timer only, controlled by the Timer 1 control bits (see text). Timer 1 in this mode is stopped. (Mode 3)

P89LPC906/907/908

Figure 5-2: Timer/Counter Auxiliary Mode Control register (TAMOD)

MODE 0

Putting either Timer into Mode 0 makes it look like an 8048 Timer, which is an 8-bit Counter with a divide-by-32 prescaler. Figure 5-4 shows Mode 0 operation.

In this mode, the Timer register is configured as a 13-bit register. As the count rolls over from all 1s to all 0s, it sets the Timer interrupt flag TFn. The count input is enabled to the Timer when TRn = 1. TRn is a control bit in the Special Function Register TCON (Figure 5-3).

The 13-bit register consists of all 8 bits of THn and the lower 5 bits of TLn. The upper 3 bits of TLn are indeterminate and should be ignored. Setting the run flag (TRn) does not clear the registers.

Mode 0 operation is the same for Timer 0 and Timer 1. See Figure 5-4.

Mode 1 is the same as Mode 0, except that all 16 bits of the timer register (THn and TLn) are used. See Figure 5-5.

MODE 2

Mode 2 configures the Timer register as an 8-bit Counter (TLn) with automatic reload, as shown in Figure 5-6. Overflow from TLn not only sets TFn, but also reloads TLn with the contents of THn, which must be preset by software. The reload leaves THn unchanged. Mode 2 operation is the same for Timer 0 and Timer 1.

2003 Dec 8 42

Philips Semiconductors

User’s Manual - Preliminary -

TIMERS 0 AND 1

P89LPC906/907/908

MODE 3

When Timer 1 is in Mode 3 it is stopped. The effect is the same as setting TR1 = 0.

Timer 0 in Mode 3 establishes TL0 and TH0 as two separate 8-bit counters. The logic for Mode 3 on Timer 0 is shown in Figure 5-7. TL0 uses the Timer 0 control bits: TR0 and TF0. TH0 is locked into a timer function (counting machine cycles) and takes over the use of TR1 and TF1 from Timer 1. Thus, TH0 now controls the “Timer 1” interrupt.

Mode 3 is provided for applications that require an extra 8-bit timer.

Note: When Timer 0 is in Mode 3, Timer 1 can be turned on and off by switching it into and out of its own Mode 3. It can still be used by the serial port as a baud rate generator (P89LPC907,P89LPC908), or in any application not requiring an interrupt.

MODE 6 - P89LPC907

In this mode, Timer 0 can be changed to a PWM with a full period of 256 timer clocks (see Figure 5-8). Its structure is similar to mode 2, except that:

• TF0 is set and cleared in hardware;

• The low period of the TF0 is in TH0, and should be between 1 and 254, and;

• The high period of the TF0 is always 256-TH0.

• Loading TH0 with 00h will force the T0 pin high, loading TH0 with FFh will force the T0 pin low.

Note that an interrupt can still be enabled on the low to high transition of TF0, and that TF0 can still be cleared in software as in any other modes.

TCON

Address: 88h

Bit addressable

Reset Source(s): Any reset

Reset Value: 00000000B

BIT SYMBOL FUNCTION

TCON.7 TF1 Timer 1 overflow flag. Set by hardware on Timer overflow. Cleared by hardware when the

TCON.6 TR1 Timer 1 Run control bit. Set/cleared by software to turn Timer 1 on/off.

TCON.5 TF0 Timer 0 overflow flag. Set by hardware on Timer/Counter overflow. Cleared by hardware

TCON.4 TR0 Timer 0 Run control bit. Set/cleared by software to turn Timer/Counter 0 on/off.

TCON.3 - Reserved for future use. Should not be set to 1 by user programs.

TCON.2 - Reserved for future use. Should not be set to 1 by user programs.

TCON.1 - Reserved for future use. Should not be set to 1 by user programs.

TCON.0 - Reserved for future use. Should not be set to 1 by user programs.

76543210

TF1 TR1 TF0 TR0 - - - -

interrupt is processed, or by software.

when the processor vectors to the interrupt routine, or by software. (except in mode 6, see above, when it is cleared in hardware)

Figure 5-3: Timer/Counter Control register (TCON)

2003 Dec 8 43

Philips Semiconductors

User’s Manual - Preliminary -

TIMERS 0 AND 1

PCLK

T0 Pin*

TRn

* T0 Pin functions available on P89LPC907

PCLK

T0 Pin*

T0C/T

Figure 5-4: Timer/Counter 0 or 1 in Mode 0 (13-bit counter)

T0C/T = 0

T0C/T = 1

= 0

= 1

Control

TLn

(5-bits)

TLn

(8-bits)

Overflow

THn

(8-bits)

Toggle

ENT0 (AUXR1.4)

Overflow

THn

(8-bits)

P89LPC906/907/908

TFn

Interrupt

T0 Pin*

Interrupt

TRn

* T0 Pin functions available on P89LPC907

Figure 5-5: Timer/Counter 0 or 1 in Mode 1 (16-bit counter)

= 0

PCLK

T0 Pin*

TRn

* T0 Pin functions available on P89LPC907

T0C/T

T0C/T = 1

Figure 5-6: Timer/Counter 0 or 1 in Mode 2 (8-bit auto-reload)

Control

TLn

(8-bits)

THn

(8-bits)

Reload

Toggle

ENT0 (AUXR1.4)

Overflow

Toggle

ENT0 (AUXR1.4)

TFn

T0 Pin*

Interrupt

T0 Pin*

2003 Dec 8 44

Philips Semiconductors

User’s Manual - Preliminary -

TIMERS 0 AND 1

PCLK

T0 Pin*

TR0

PC LK

TR1

Figure 5-7: Timer/Counter 0 Mode 3 (two 8-bit counters)

C/T

= 0

= 1

Control

TL0

(8-bits)

TH0

(8-bits)

P89LPC906/907/908

Overflow

Toggle

Overflow

* T0 Pin functions available on P89LPC907

TF0

ENT0

TF1

Interrupt

T0 Pin*

Interrupt

PCLK

TR0

Figure 5-8: Timer/Counter 0 in Mode 6 (PWM auto-reload), P89LPC907.

T0C/T = 0

Control

TL0

(8-bits)

Reload TH0 on falling transition

and (256-TH0) on rising transition

TH0

(8-bits)

Overflow

Toggle

ENT0 (AUXR1.4)

TF0

Interrupt

T0 Pin

TIMER OVERFLOW TOGGLE OUTPUT - P89LPC907

Timer 0 can be configured to automatically toggle the T0 pin whenever the timer overflow occurs. This function is enabled by control bit ENT0 in the AUXR1 register. The port output will be a logic 1 prior to the first timer overflow when this mode is turned on. In order for this mode to function, the T0C/T

bit must be cleared selecting PCLK as the clock source for the timer.

2003 Dec 8 45

Philips Semiconductors

User’s Manual - Preliminary -

TIMERS 0 AND 1

P89LPC906/907/908

2003 Dec 8 46

Philips Semiconductors

User’s Manual - Preliminary -

REAL-TIME CLOCK/SYSTEM TIMER

P89LPC906/907/908

6. REAL-TIME CLOCK/SYSTEM TIMER

The P89LPC906/907/908 has a simple Real-time clock/system timer that allows a user to continue running an accurate timer while the rest of the device is powered down. The Real-time clock can be an interrupt or a wake-up source (see Figure 6-2). The Real-time clock is a 23-bit down counter.

REAL-TIME CLOCK SOURCE

On the P89LPC906 the clock source for this counter can be either CCLK or the XTAL1-2 oscillator (XCLK) . On the P89LPC907 and P89LPC908 devicesthe clock source for this counter is CCLK. Please refer to Figure 2-3 "Block Diagram of Oscillator Control

- P89LPC906" in section "Clocks" on page 25. CCLK can have either the XTAL1-2 oscillator, the internal RC oscillator, or the

Watchdog oscillator as its clock source. If the XTAL1-2 oscillator is used for producing CCLK, the RTC will use either the XTAL12 oscillator’s output or CCLK as its clock source. The possible clocking combinations are shown in Table , below.

There are three SFRs used for the RTC:

• RTCCON - Real-time clock control.

• RTCH - Real-time clock counter reload high (bits 22-15).

• RTCL - Real-time clock counter reload low (bits 14-7).

The Real-time clock/system timer can be enabled by setting the RTCEN (RTCCON.0) bit. The Real-time clock is a 23-bit down counter (initialized to all 0’s when RTCEN = 0) that is comprised of a 7-bit prescaler and a 16-bit loadable down counter. When RTCEN is written with ’1’, the counter is first loaded with (RTCH,RTCL,’1111111’) and will count down. When it reaches all 0’s, the counter will be reloaded again with (RTCH,RTCL,’1111111’) and a flag - RTCF (RTCCON.7) - will be set.

Any write to RTCH and RTCL in-between the Real-time clock reloading will not cause reloading of the counter. When the current count terminates, the contents of RTCH and RTCL will be loaded into the counter and the new count will begin. An immediate reload of the counter can be forced by clearing the RTCEN bit to ’0’ and then setting it back to ’1’ .

2003 Dec 8 47

Philips Semiconductors

User’s Manual - Preliminary -

REAL-TIME CLOCK/SYSTEM TIMER

Power-On

Reset

RTCH RTCL

Reload on underflow

MSB

Wake up from

Power-down

Interrupt

if enabled

(shared w. WDT)

LSB

23-bit down counter

RTCF

ERTC

Figure 6-1: Real-time clock/system timer Block Diagram

RTC underflow flag

RTC Reset

7-bit prescaler

÷ 128

RTCEN

RTC Enable

P89LPC906/907/908

XTAL1XTAL2

Low freq.

Med. freq.

High freq.

CCLK

Int. Osc’s

RTCS1 RTCS2

RTC clk select

Table 6-1: Real-time Clock/System Timer Clock Source - P89LPC906

FOSC2

(UCFG1.2)

FOSC1

(UCFG1.1)

FOSC0

(UCFG1.0)

RTCS1:0

CCLK Frequency RTC Clock Frequency

000

High frequency crystal/DIVM

001

Medium frequency crystal/DIVM

010

Low frequency crystal/DIVM

High frequency crystal

(XCLK)

High frequency crystal/DIVM

(CCLK)

Medium frequency crystal

(XCLK)

Medium frequency crystal/

DIVM (CCLK)

Low frequency crystal

(XCLK)

Low frequency crystal/DIVM

(CCLK)

2003 Dec 8 48

Philips Semiconductors

User’s Manual - Preliminary -

REAL-TIME CLOCK/SYSTEM TIMER

FOSC2

(UCFG1.2)

011

100

101

110

111

FOSC1

(UCFG1.1)

FOSC0

(UCFG1.0)

RTCS1:0

11 RC Oscillator/DIVM (CCLK)

xx undefined

11 external clock/DIVM (CCLK)

CCLK Frequency RTC Clock Frequency

RC Oscillator/DIVM

WDT Oscillator/DIVM

external clock/DIVM

P89LPC906/907/908

High frequency crystal

(XCLK)

Medium frequency crystal

(XCLK)

Low frequency crystal

(XCLK)

High frequency crystal

(XCLK)

Medium frequency crystal

(XCLK)

Low frequency crystal

(XCLK)

WDT Oscillator/DIVM

(CCLK)

external clock

(XCLK)

Table 6-2: Real-time Clock/System Timer Clock Source - P89LPC907,P89LPC908

FOSC2

(UCFG1.2)

000

010

011

2003 Dec 8 49

FOSC1

(UCFG1.1)

FOSC0

(UCFG1.0)

RTCS1:0

x undefined001

11 RC Oscillator/DIVM (CCLK)

CCLK Frequency RTC Clock Frequency

RC Oscillator/DIVM

undefined01

Philips Semiconductors

User’s Manual - Preliminary -

REAL-TIME CLOCK/SYSTEM TIMER

FOSC2

(UCFG1.2)

100

101

111

FOSC1

(UCFG1.1)

FOSC0

(UCFG1.0)

RTCS1:0

xx undefined110

CCLK Frequency RTC Clock Frequency

WDT Oscillator/DIVM

P89LPC906/907/908

undefined01

(CCLK)

CHANGING RTCS1-0

RTCS1-0 cannot be changed if the RTC is currently enabled (RTCCON.0 =1). Setting RTCEN and updating RTCS1-0 may be done in a single write to RTCCON. However, if RTCEN = 1, this bit must first be cleared before updating RTCS1-0

REAL-TIME CLOCK INTERRUPT/WAKE UP

If ERTC (RTCCON.1), EWDRT (IEN0.6) and EA (IEN0.7) are set to ’1’, RTCF can be used as an interrupt source. This interrupt vector is shared with the watchdog timer. It can also be a source to wake up the device.

RESET SOURCES AFFECTING THE REAL-TIME CLOCK

Only power-on reset will reset the Real-time Clock and its associated SFRs to their default state.

2003 Dec 8 50

Philips Semiconductors

User’s Manual - Preliminary -

REAL-TIME CLOCK/SYSTEM TIMER

RTCCON

Address: D1h

Not bit addressable

Reset Source(s): Power-up only

Reset Value: 011xxx00B

BIT SYMBOL FUNCTION

RTCCON.7 RTCF Real-time Clock Flag. This bit is set to ’1’ when the 23-bit Real-time clock reaches a count

of ’0’. It can be cleared in software.

RTCCON.6-5 RTCS1-0 Real-time Clock source select (see Table ,Table ).

RTCCON.4-2 - Reserved for future use. Should not be set to 1 by user programs.

RTCCON.1 ERTC Real-time Clock interrupt enable. The Real-time clock shares the same interrupt as the

watchdog timer. Note that if the user configuration bit WDTE (UCFG1.7) is ’0’, the watchdog timer can be enabled to generate an interrupt. Users can read the RTCF (RTCCON.7) bit to determine whether the Real-time clock caused the interrupt.

RTCCON.0 RTCEN Real-time Clock enable. The Real-time clock will be enabled if this bit is ’1’. Note that this

bit will not Power down the Real-time Clock. The RTCPD bit (PCONA.7) if set, will Power down and disable this block regardless of RTCEN.

76543210

RTCF RTCS1 RTCS0 - - - ERTC RTCEN

Figure 6-2: RTCCON Register

P89LPC906/907/908

2003 Dec 8 51

Philips Semiconductors

User’s Manual - Preliminary -

REAL-TIME CLOCK/SYSTEM TIMER

P89LPC906/907/908

2003 Dec 8 52

Philips Semiconductors

User’s Manual - Preliminary -

POWER MONITORING FUNCTIONS

P89LPC906/907/908

7. POWER MONITORING FUNCTIONS

The P89LPC906/907/908 incorporates power monitoring functions designed to prevent incorrect operation during initial poweron and power loss or reduction during operation. This is accomplished with two hardware functions: Power-on Detect and Brownout Detect.

BROWNOUT DETECTION

The Brownout Detect function determines if the power supply voltage drops below a certain level. The default operation for a Brownout Detection is to cause a processor reset. However, it may alternatively be configured to generate an interrupt by setting the BOI (PCON.4) bit and the EBO (IEN0.5) bit.

Enabling and disabling of Brownout Detection is done via the BOPD (PCON.5) bit, bit field PMOD1-0 (PCON.1-0) and user configuration bit BOE (UCFG1.5). If BOE is in an unprogrammed state, brownout is disabled regardless of PMOD1-0 and BOPD. If BOE is in a programmed state, PMOD1-0 and BOPD will be used to determine whether Brownout Detect will be disabled or enabled. PMOD1-0 is used to select the power reduction mode. If PMOD1-0 = ’11’, the circuitry for the Brownout Detection is disabled for lowest power consumption. BOPD defaults to ’0’, indicating brownout detection is enabled on power-on if BOE is programmed.

If Brownout Detection is enabled, the operating voltage range for V

falls below the Brownout trip voltage, V

If Brownout Detection is disabled, the operating voltage range for VDD is 2.4V-3.6V. If the P89LPC906/907/908 device is to operate with a power supply that can be below 2.7V, BOE should be left in the unprogrammed state so that the device can operate at 2.4V, otherwise continuous brownout reset may prevent the device from operating.

If Brownout Detect is enabled (BOE programmed, PMOD1-0 ≠ ’11’, BOPD = 0), BOF (RSTSRC.5) will be set when a brownout is detected, regardless of whether a reset or an interrupt is enabled, . BOF will stay set until it is cleared in software by writing ’0’ to the bit. Note that if BOE is unprogrammed, BOF is meaningless. If BOE is programmed, and a initial power-on occurs, BOF will be set in addition to the power-on flag (POF - RSTSRC.4).

For correct activation of Brownout Detect, certain V specifications.

(see D.C. Electrical Characteristics), and is negated when VDD rises above VBO.

rise and fall times must be observed. Please see the datasheet for

is 2.7V-3.6V, and the brownout condition occurs when

2003 Dec 8 53

Philips Semiconductors

User’s Manual - Preliminary -

POWER MONITORING FUNCTIONS

Table 7-1: Brownout Options

BOE

(UCFG1.5)

0 (erased)XX XXXX

1 (programmed)

PMOD1-0

(PCON.1-0)

(total power

down)

≠ 11

(any mode

other than

total power

down)

BOPD

(PCON.5)

XXXX

(brownout

detect

powered

down)

(brownout

detect

active)

BOI

(PCON.4)

XXX

(brownout

detect

generates

reset)

(brownout

detect

generates

interrupt)

EBO

(IEN0.5)

(enable

brownout

interrupt)

0 X Both brownout reset and interrupt disabled. V

(IEN0.7)

(global

interrupt

enable)

P89LPC906/907/908

Description

Brownout disabled. V

Brownout disabled. V However, BOPD is default to ’0’ upon power-up.

Brownout reset enabled. V

3.6V. Upon a brownout reset, BOF (RSTSRC.5) will be set to indicate the reset source. BOF can be cleared by writing ’0’ to the bit.

Brownout interrupt enabled. V

3.6V. Upon a brownout interrupt, BOF (RSTSRC.5) will be set. BOF can be cleared by writing ’0’ to the bit.

operating range is 2.4V-3.6V. However, BOF (RSTSRC.5) will be set when V Detection trip point. BOF can be cleared by writing ’0’ to the bit.

operating range is 2.4V-3.6V.

operating range is 2.7V-

falls to the Brownout

POWER-ON DETECTION

The Power-On Detect has a function similar to the Brownout Detect, but is designed to work as power initially comes up, before the power supply voltage reaches a level where the Brownout Detect can function. The POF flag (RSTSRC.4) is set to indicate an initial power-on condition. The POF flag will remain set until cleared by software by writing ’0’ to the bit. Note that if BOE (UCFG1.5) is programmed, BOF (RSTSRC.5) will be set when POF is set. If BOE is unprogrammed, BOF is meaningless.

POWER REDUCTION MODES

The P89LPC906/907/908 supports three different power reduction modes as determined by SFR bits PCON.1-0 (see Table ):

2003 Dec 8 54

Philips Semiconductors

User’s Manual - Preliminary -

POWER MONITORING FUNCTIONS

Table 7-2: Power Reduction Modes

PMOD1

(PCON.1)

0 0 Normal Mode (Default) - no power reduction.

PMOD0

(PCON.0)

Description

Idle Mode. The Idle mode leaves peripherals running in order to allow them to activate the processor when an interrupt is generated. Any enabled interrupt source or reset may terminate Idle mode.

Power down mode: The Power down mode stops the oscillator in order to minimize power consumption. The P89LPC906/907/908 exits Power down mode via any reset, or certain interrupts - brownout Interrupt, keyboard, Real-time clock (system timer), watchdog, and comparator trips. Waking up by reset is only enabled if the corresponding reset is enabled, and waking up by interrupt is only enabled if the corresponding interrupt is enabled and the EA SFR bit (IEN0.7) is set. In Power down mode the internal RC oscillator is disabled unless both the RC oscillator has been selected as the system clock AND the RTC is enabled In Power down mode, the power supply voltage may be reduced to the RAM keep-alive voltage V This retains the RAM contents at the point where Power down mode was entered. SFR contents are not guaranteed after VDD has been lowered to V via Reset in this situation. V

must be raised to within the operating range before the Power down mode

RAM

is exited. When the processor wakes up from Power down mode, it will start the oscillator immediately and begin execution when the oscillator is stable. Oscillator stability is determined by counting 1024 CPU clocks after start-up when one of the crystal oscillator configurations is used, or 256 clocks after start-up for the internal RC or external clock input configurations. Some chip functions continue to operate and draw power during Power down mode, increasing the total power used during Power down. These include:

• Brownout Detect

• Watchdog Timer if WDCLK (WDCON.0) is ’1’.

• Comparator (Note: Comparator can be powered down separately with PCONA.5 set to ’1’ and comparator disabled);

• Real-time Clock/System Timer (and the crystal oscillator circuitry if this block is using it, unless RTCPD, i.e., PCONA.7 is ’1’).

Total Power down mode: This is the same as Power down mode except that the Brownout Detection circuitry and the voltage comparators are also disabled to conserve additional power. Note that a brownout reset or interrupt will not occur. Voltage comparator interrupts and Brownout interrupt cannot be used as a wakeup source.The internal RC oscillator is disabled unless both the RC oscillator has been selected as the system clock AND the RTC is enabled. The following are the wakeup options supported:

• Watchdog Timer if WDCLK (WDCON.0) is ’1’. Could generate Interrupt or Reset, either one can wake up the device

• Keyboard Interrupt

• Real-time Clock/System Timer (and the crystal oscillator circuitry if this block is using it, unless RTCPD, i.e., PCONA.7 is ’1’).

• Note: Using the internal RC-oscillator to clock the RTC during Power down may result in relatively high power consumption. Lower power consumption can be achieved by using an external low frequency clock when the Real-time Clock is running during Power down.

P89LPC906/907/908

RAM

, therefore it is recommended to wake up the processor

2003 Dec 8 55

Philips Semiconductors

User’s Manual - Preliminary -

POWER MONITORING FUNCTIONS

PCON

Address: 87h

Not bit addressable

Reset Source(s): Any reset

Reset Value: 00000000B

BIT SYMBOL FUNCTION

PCON.7 SMOD1 Double Baud Rate bit for the serial port (UART) when Timer 1 is used as the baud rate

PCON.6 SMOD0 Framing Error Location (P89LPC908):

PCON.5 BOPD Brownout Detect Power down. When 1, Brownout Detect is powered down and therefore

PCON.4 BOI Brownout Detect Interrupt Enable. When 1, Brownout Detection will generate a interrupt .

PCON.3 GF1 General Purpose Flag 1. May be read or written by user software, but has no effect on

PCON.2 GF0 General Purpose Flag 0. May be read or written by user software, but has no effect on

PCON.1-0 PMOD1-PMOD0 Power Reduction Mode (see section "Power Reduction Modes").

76543210

SMOD1 SMOD0 BOPD BOI GF1 GF0 PMOD1 PMOD0

source. When 1, the Timer 1 overflow rate is supplied to the UART. When 0, the Timer 1 overflow rate is divided by 2 before being supplied to the UART. P89LPC907, P89LPC908(See Figure 8-2).

-When 0, bit 7 of SCON is accessed as SM0 for the UART.

-When 1, bit 7 of SCON is accessed as the framing error status (FE) for the UART.

This bit also determines the location of the UART receiver interrupt RI (see description on RI in Figure 8-3).

disabled. When 0, Brownout Detect is enabled. (Note: BOPD must be ’0’ before any programming or erasing commands can be issued. Otherwise these commands will be aborted.)

When 0, Brownout Detection will cause a reset.

operation.

P89LPC906/907/908

Figure 7-1: Power Control Register (PCON)

2003 Dec 8 56

Philips Semiconductors

User’s Manual - Preliminary -

POWER MONITORING FUNCTIONS

PCONA

Address: B5H

Not bit addressable

Reset Source(s): Any reset

Reset Value: 00000000B

BIT SYMBOL FUNCTION

PCONA.7 RTCPD Real-time Clock Power down: When ’1’, the internal clock to the Real-time Clock is

PCONA.6 - Not used. Reserved for future use.

PCONA.5 VCPD Analog Voltage Comparator Power down: When ’1’, the voltage comparator is powered

PCONA.4 - Not used. Reserved for future use.

PCONA.3 - Not used. Reserved for future use.

PCONA.2 - Not used. Reserved for future use.

PCONA.1 SPD Serial Port (UART) Power down: When ’1’, the internal clock to the UART is disabled. Note

PCONA.0 - Not used. Reserved for future use.

76543210

RTCPD - VCPD - - - SPD -

disabled.

down. User must disable the voltage comparator prior to setting this bit.

that in either Power down mode or Total Power down mode, the UART clock will be disabled regardless of this bit (P89LPC907,P89LPC908).

P89LPC906/907/908

Figure 7-2: Power Control Register (PCONA)

2003 Dec 8 57

Philips Semiconductors

User’s Manual - Preliminary -

POWER MONITORING FUNCTIONS

P89LPC906/907/908

2003 Dec 8 58

Philips Semiconductors

User’s Manual - Preliminary -

UART

P89LPC906/907/908

8. UART (P89LPC907, P89LPC908)

The P89LPC907 and P89LPC908 devices have an enhanced UART that is compatible with the conventional 80C51 UART, except that Timer 2 overflow cannot be used as a baud rate source. The UART does include an independent Baud Rate Generator. The baud rate can be selected from the CCLK (divided by a constant), Timer 1 overflow, or the independent Baud Rate Generator.

The UART in the P89LPC907 does not include the RxD pin and descriptions of the receiver functions in this chapter do not apply to the P89LPC907. The transmitter is available for use in applications requiring the transmission of serial data. Often the transmitter function is useful for providing information during the debugging process.

In addition to the baud rate generation, enhancements over the standard 80C51 UART include Framing Error detection, break detect, automatic address recognition, selectable double buffering and several interrupt options. The UART can be operated in 4 modes:

MODE 0

Serial data enters and exits through RxD. TxD outputs the shift clock. 8 bits are transmitted or received, LSB first. The baud rate is fixed at 1/16 of the CCLK.

MODE 1

10 bits are transmitted (through TxD) or received (through RxD): a start bit (logical 0), 8 data bits (LSB first), and a stop bit (logical

1). When data is received, the stop bit is stored in RB8 in Special Function Register SCON. The baud rate is variable and is determined by the Timer 1 overflow rate or the Baud Rate Generator (see "Baud Rate Generator and Selection" section).

MODE 2

11 bits are transmitted (through TxD) or received (through RxD): start bit (logical 0), 8 data bits (LSB first), a programmable 9th data bit, and a stop bit (logical 1). When data is transmitted, the 9th data bit (TB8 in SCON) can be assigned the value of 0 or 1. Or, for example, the parity bit (P, in the PSW) could be moved into TB8. When data is received, the 9th data bit goes into RB8 in Special Function Register SCON and the stop bit is not saved. The baud rate is programmable to either 1/16 or 1/32 of the CCLK frequency, as determined by the SMOD1 bit in PCON.

MODE 3

11 bits are transmitted (through TxD) or received (through RxD): a start bit (logical 0), 8 data bits (LSB first), a programmable 9th data bit, and a stop bit (logical 1). Mode 3 is the same as Mode 2 in all respects except baud rate. The baud rate in Mode 3 is variable and is determined by the Timer 1 overflow rate or the Baud Rate Generator (see "Baud Rate Generator and Selection" section).

In all four modes, transmission is initiated by any instruction that uses SBUF as a destination register. Reception is initiated in Mode 0 by the condition RI = 0 and REN = 1. Reception is initiated in the other modes by the incoming start bit if REN = 1.

2003 Dec 8 59

Philips Semiconductors

User’s Manual - Preliminary -

UART

SFR SPACE

The UART SFRs are at the following locations:

Table 8-1: SFR Locations for UARTs

PCON Power Control 87H

SCON Serial Port (UART) Control 98H

SBUF Serial Port (UART) Data Buffer 99H

SADDR Serial Port (UART) Address A9H

SADEN Serial Port (UART) Address Enable B9H

SSTAT Serial Port (UART) Status BAH

BRGR1 Baud Rate Generator Rate High Byte BFH

BRGR0 Baud Rate Generator Rate Low Byte BEH

BRGCON Baud Rate Generator Control BDH

BAUD RATE GENERATOR AND SELECTION

P89LPC906/907/908

The enhanced UART has an independent Baud Rate Generator. The baud rate is determined by a value programmed into the BRGR1 and BRGR0 SFRs. The UART can use either Timer 1 or the baud rate generator output as determined by BRGCON.21 (see Figure 8-2). Note that Timer T1 is further divided by 2 if the SMOD1 bit (PCON.7) is cleared. The independent Baud Rate Generator uses CCLK.

UPDATING THE BRGR1 AND BRGR0 SFRS

The baud rate SFRs, BRGR1 and BRGR0 must only be loaded when the Baud Rate Generator is disabled (the BRGEN bit in the BRGCON register is ’0’). This avoids the loading of an interim value to the baud rate generator. (CAUTION: If either BRGR0

or BRGR1 is written when BRGEN = 1, the result is unpredictable.)

Table 8-2: Baud Rate Generation for UART

SCON.7

(SM0)

0 0 X X CCLK/16

SCON.6

(SM1)

PCON.7

(SMOD1)

0 0 CCLK/(256-TH1)64

1 0 CCLK/(256-TH1)32

X 1 CCLK/((BRGR1,BRGR0)+16)

0 X CCLK/32

1 X CCLK/16

0 0 CCLK/(256-TH1)64

1 0 CCLK/(256-TH1)32

BRGCON.1

(SBRGS)

Receive/Transmit Baud Rate for UART

X 1 CCLK/((BRGR1,BRGR0)+16)

2003 Dec 8 60

Philips Semiconductors

User’s Manual - Preliminary -

UART

P89LPC906/907/908

BRGCON

Address: BDh

Not bit addressable

76543210

- - - - - - SBRGS BRGEN

Reset Source(s): Any reset

Reset Value: xxxxxx00B

BIT SYMBOL FUNCTION

BRGCON.7-2 - Reserved for future use. Should not be set to 1 by user programs.

BRGCON.1 SBRGS Select Baud Rate Generator as the source for baud rates to UART in modes 1 & 3 (see

Table for details)

BRGCON.0 BRGEN Baud Rate Generator Enable. Enables the baud rate generator. BRGR1 and BRGR0 can

only be written when BRGEN =0.

Figure 8-1: BRGCON Register

Timer 1 Overflow

(PCLK-based)

Baud Rate Generator

(CCLK-based)

SMOD1 = 1

÷2

SMOD1 = 0

SBRGS = 0

Baud Rate Modes 1 and 3

SBRGS = 1

Figure 8-2: Baud Rate Generations for UART (Modes 1, 3)

FRAMING ERROR

A Framing error occurs when the stop bit is sensed as a logic ’0’. A Framing error is reported in the status register (SSTAT). In addition, if SMOD0 (PCON.6) is 1, framing errors can be made available in SCON.7. If SMOD0 is 0, SCON.7 is SM0. It is recommended that SM0 and SM1 (SCON.7-6) are programmed when SMOD0 is ’0’.

BREAK DETECT

A break is detected when any 11 consecutive bits are sensed low. A break detect is reported in the status register (SSTAT). Since a break condition also satisfies the requirements for a framing error, a break condition will also result in reporting a framing error. Once a break condition has been detected, the UART will go into an idle state and remain in this idle state until a stop bit has been received. The break detect can be used to reset the device by setting the EBRR bit (AUXR1.6).

A break detect reset will force the high byte of the program counter to be equal to the Boot Vector contents and the low byte cleared to 00h. The first instruction will be fetched from this address.

2003 Dec 8 61

Philips Semiconductors

User’s Manual - Preliminary -

UART

SCON

Address: 98h

Bit addressable

Reset Source(s): Any reset

Reset Value: 00000000B

BIT SYMBOL FUNCTION

SCON.7 SM0/FE The use of this bit is determined by SMOD0 in the PCON register. If SMOD0 = 0, this bit

is read and written as SM0, which with SM1, defines the serial port mode. If SMOD0 = 1, this bit is read and written as FE (Framing Error). FE is set by the receiver when an invalid stop bit is detected. Once set, this bit cannot be cleared by valid frames but is cleared by software. (Note: UART mode bits SM0 and SM1 should be programmed when SMOD0 is ’0’ - default mode on any reset.)

SCON. 6 SM1 With SM0, defines the serial port mode (see table below).

SM0, SM1

0 0 0: shift register CCLK/16 (default mode on any reset)

0 1 1: 8-bit UART Variable (see Table )

1 0 2: 9-bit UART CCLK/32 or CCLK/16

1 1 3: 9-bit UART Variable (see Table )

SCON.5 SM2 Enables the multiprocessor communication feature in Modes 2 and 3. In Mode 2 or 3, if

SCON.4 REN Enables serial reception. Set by software to enable reception. Clear by software to disable

SCON.3 TB8 The 9th data bit that will be transmitted in Modes 2 and 3. Set or clear by software as

SCON.2 RB8 The 9th data bit that was received in Modes 2 and 3. In Mode 1 (SM2 must be 0), RB8 is

SCON.1 TI Transmit interrupt flag. Set by hardware at the end of the 8th bit time in Mode 0, or at the

SCON.0 RI Receive interrupt flag. Set by hardware at the end of the 8th bit time in Mode 0, or

UART Mode UART 0 Baud Rate

SM2 is set to 1, then Rl will not be activated if the received 9th data bit (RB8) is 0. In Mode 0, SM2 should be 0. In Mode 1, SM2 must be 0.

reception.

desired.

the stop bit that was received. In Mode 0, RB8 is undefined.

the stop bit (see description of INTLO bit in SSTAT register) in the other modes. Must be cleared by software.

approximately halfway through the stop bit time in Mode 1. For Mode 2 or Mode 3, if SMOD0, it is set near the middle of the 9th data bit (bit 8). If SMOD0 = 1, it is set near the middle of the stop bit (see SM2 - SCON.5 - for exceptions). Must be cleared by software.

76543210

SM0/FE SM1 SM2 REN TB8 RB8 TI RI

P89LPC906/907/908

Figure 8-3: Serial Port Control Register (SCON)

2003 Dec 8 62

Philips Semiconductors

User’s Manual - Preliminary -

UART

SSTAT

Address: BAh

Not bit addressable

Reset Source(s): Any reset

Reset Value: 00000000B

BIT SYMBOL FUNCTION

SSTAT.7 DBMOD Double buffering mode. When set = 1 enables double buffering. Must be ’0’ for UART

SSTAT.6 INTLO Transmit interrupt position. When cleared = 0, the Tx interrupt is issued at the beginning

SSTAT.5 CIDIS Combined Interrupt Disable. When set = 1, Rx and Tx interrupts are separate. When

SSTAT.4 DBISEL Double buffering transmit interrupt select. Used only if double buffering is enabled.This bit

SSTAT.3 FE Framing error flag is set when the receiver fails to see a valid STOP bit at the end of the

SSTAT.2 BR Break Detect flag. A break is detected when any 11 consecutive bits are sensed low.

SSTAT.1 OE Overrun Error flag is set if a new character is received in the receiver buffer while it is still

SSTAT.0 STINT Status Interrupt Enable. When set =1, FE, BR, or OE can cause an interrupt. The

76543210

DBMOD INTLO CIDIS DBISEL FE BR OE STINT

mode 0. In order to be compatible with existing 80C51 devices, this bit is reset to ’0’ to disable double buffering.

of the stop bit. When set =1, the Tx interrupt is issued at end of the stop bit. Must be ’0’ for mode 0. Note that in the case of single buffering, if the Tx interrupt occurs at the end of a STOP bit, a gap may exist before the next start bit.

cleared = 0, the UART uses a combined Tx/Rx interrupt (like a conventional 80C51 UART). This bit is reset to ’0’ to select combined interrupts.

controls the number of interrupts that can occur when double buffering is enabled. When set, one transmit interrupt is generated after each character written to SBUF, and there is also one more transmit interrupt generated at the beginning (INTLO = 0) or the end (INTLO = 1) of the STOP bit of the last character sent (i.e., no more data in buffer). This last interrupt can be used to indicate that all transmit operations are over. When cleared = 0, only one transmit interrupt is generated per character written to SBUF. Must be ’0’ when double buffering is disabled.

Note that except for the first character written (when buffer is empty), the location of the transmit interrupt is determined by INTLO. When the first character is written, the transmit interrupt is generated immediately after SBUF is written.

frame. Cleared by software.

Cleared by software.

full (before the software has read the previous character from the buffer), i.e., when bit 8 of a new byte is received while RI in SCON is still set. Cleared by software.

interrupt used (vector address 0023h) is shared with RI (CIDIS = 1) or the combined TI/RI (CIDIS = 0). When cleared = 0, FE, BR, OE cannot cause an interrupt. (Note: FE, BR, or OE is often accompanied by a RI, which will generate an interrupt regardless of the state of STINT). Note that BR can cause a break detect reset if EBRR (AUXR1.6) is set to ’1’.

P89LPC906/907/908

Figure 8-4: Serial Port Status Register (SSTAT)

MORE ABOUT UART MODE 0

In Mode 0, a write to SBUF will initiate a transmission. At the end of the transmission, TI (SCON.1) is set, which must be cleared in software. Double buffering must be disabled in this mode.

Reception is initiated by clearing RI (SCON.0). Synchronous serial transfer occurs and RI will be set again at the end of the transfer. When RI is cleared, the reception of the next character will begin. Refer to Figure 8-5 for timing.

2003 Dec 8 63

Philips Semiconductors

User’s Manual - Preliminary -

UART

S1...S16 S1...S16 S1...S16 S1...S16S1...S16S1...S16 S1...S16 S1...S16 S1...S16 S1...S16S1...S16S1...S16 S1...S16

Write to SBUF

Shift

RxD (Data Out)

TxD (Shift Clock)

Write to SCON (Clear RI)

Shift

RxD (Data In)

TxD (Shift Clock)

Figure 8-5: Serial Port Mode 0 (Double Buffering Must Be Disabled)

MORE ABOUT UART MODE 1

D0 D1 D5D2 D6D3 D4 D7

P89LPC906/907/908

Transmit

Receive

D0 D1 D5D2 D6D3 D4 D7

Reception is initiated by detecting a 1-to-0 transition on RxD. RxD is sampled at a rate 16 times the programmed baud rate. When a transition is detected, the divide-by-16 counter is immediately reset. Each bit time is thus divided into 16 counter states. At the 7th, 8th, and 9th counter states, the bit detector samples the value of RxD. The value accepted is the value that was seen in at least 2 of the 3 samples. This is done for noise rejection. If the value accepted during the first bit time is not 0, the receive circuits are reset and the receiver goes back to looking for another 1-to-0 transition. This provides rejection of false start bits. If the start bit proves valid, it is shifted into the input shift register, and reception of the rest of the frame will proceed.

The signal to load SBUF and RB8, and to set RI, will be generated if, and only if, the following conditions are met at the time the final shift pulse is generated: RI = 0 and either SM2=0 or the received stop bit =1. If either of these two conditions is not met, the received frame is lost. If both conditions are met, the stop bit goes into RB8, the 8 data bits go into SBUF, and RI is activated.

TX Clock

Write to SBUF

Shift

TxD

RX Clock

RxD

Shift

÷ 16 Reset

Start Bit Stop Bit

Start Bit

D0 D1 D5D2 D6D3 D4 D7

INTLO = 0

D0 D1 D5D2 D6D3 D4 D7

Stop Bit

INTLO = 1

Transmit

Receive

Figure 8-6: Serial Port Mode 1 (Only Single Transmit Buffering Case Is Shown)

2003 Dec 8 64

Philips Semiconductors

User’s Manual - Preliminary -

UART

P89LPC906/907/908

MORE ABOUT UART MODES 2 AND 3

Reception is the same as in Mode 1.

The signal to load SBUF and RB8, and to set RI, will be generated if, and only if, the following conditions are met at the time the final shift pulse is generated. (a) RI = 0, and (b) Either SM2 = 0, or the received 9th data bit = 1. If either of these conditions is not met, the received frame is lost, and RI is not set. If both conditions are met, the received 9th data bit goes into RB8, and the first 8 data bits go into SBUF.

TX Clock

Write to SBUF

Shift

TxD

RX Clock

RxD

Shift

÷ 16 Reset

Start Bit Stop Bit

Start Bit

D0 D1 D5D2 D6D3 D4 D7

TB8

INTLO = 0

RB8

Stop Bit

Transmit

INTLO = 1

Receive

SMOD0 = 0

SMOD0 = 1

Figure 8-7: Serial Port Mode 2 or 3 (Only Single Transmit Buffering Case Is Shown)

FRAMING ERROR AND RI IN MODES 2 AND 3 WITH SM2 = 1

If SM2 = 1 in modes 2 and 3, RI and FE behave as in the following table.

Mode

PCON.6

(SMOD0)

RB8 RI FE

0 No RI when RB8 = 0 Occurs during STOP bit

Similar to Figure 8-7, with SMOD0 = 0, RI

occurs during RB8, one bit before FE

Occurs during STOP bit

0 No RI when RB8 = 0 Will NOT occur

Similar to Figure 8-7, with SMOD0 = 1, RI

occurs during STOP bit

Occurs during STOP bit

Table 8-3: FE and RI when SM2 = 1 in Modes 2 and 3.

BREAK DETECT

A break is detected when 11 consecutive bits are sensed low and is reported in the status register (SSTAT). For Mode 1, this consists of the start bit, 8 data bits, and two stop bit times. For Modes 2 & 3, this consists of the start bit, 9 data bits, and one stop bit. The break detect bit is cleared in software or by a reset. The break detect can be used to reset the device. This occurs if the UART is enabled and the the EBRR bit (AUXR1.6) is set and a break occurs.

2003 Dec 8 65

Philips Semiconductors

User’s Manual - Preliminary -

UART

P89LPC906/907/908

DOUBLE BUFFERING

The UART has a transmit double buffer that allows buffering of the next character to be written to SBUF while the first character is being transmitted. Double buffering allows transmission of a string of characters with only one stop bit between any two characters, provided the next character is written between the start bit and the stop bit of the previous character.

Double buffering can be disabled. If disabled (DBMOD, i.e. SSTAT.7 = 0), the UART is compatible with the conventional 80C51 UART. If enabled, the UART allows writing to SBUF while the previous data is being shifted out.

DOUBLE BUFFERING IN DIFFERENT MODES

Double buffering is only allowed in Modes 1, 2 and 3. When operated in Mode 0, double buffering must be disabled (DBMOD = 0).

TRANSMIT INTERRUPTS WITH DOUBLE BUFFERING ENABLED (MODES 1, 2 AND 3)

Unlike the conventional UART, when double buffering is enabled, the Tx interrupt is generated when the double buffer is ready to receive new data. The following occurs during a transmission (assuming eight data bits):

1. The double buffer is empty initially.

2. The CPU writes to SBUF.

3. The SBUF data is loaded to the shift register and a Tx interrupt is generated immediately.

4. If there is more data, go to 6, else continue on 5.

5. If there is no more data, then:

- If DBISEL is ’0’, no more interrupts will occur.

- If DBISEL is ’1’ and INTLO is ’0’, a Tx interrupt will occur at the beginning of the STOP bit of the data currently in the shifter (which is also the last data).

- If DBISEL is ’1’ and INTLO is ’1’, a Tx interrupt will occur at the end of the STOP bit of the data currently in the shifter (which is also the last data).

6. If there is more data, the CPU writes to SBUF again. Then:

- If INTLO is ’0’, the new data will be loaded and a Tx interrupt will occur at the beginning of the STOP bit of the data currently in the shifter.

- If INTLO is ’1’, the new data will be loaded and a Tx interrupt will occur at the end of the STOP bit of the data currently in the shifter.

Go to 3.

Note that if DBISEL is ’1’ and the CPU is writing to SBUF when the STOP bit of the last data is shifted out, there can be an uncertainty of whether a Tx interrupt is generated already with the UART not knowing whether there is any more data following.

2003 Dec 8 66

Philips Semiconductors

User’s Manual - Preliminary -

UART

TxD

Write to

SBUF

Tx Interrupt

TxD

Write to

SBUF

Tx Interrupt

TxD

P89LPC906/907/908

Single Buffering (DBMOD/SSTAT.7 = 0), Early Interrupt (INTLO/SSTAT.6 = 0) is Shown

Double Buffering (DBMOD/SSTAT.7 = 1), Early Interrupt (INTLO/SSTAT.6 = 0) is Shown, No End-

ing Tx Interrupt (DBISEL/SnSTAT.4 = 0)

Write to

SBUF

Tx Interrupt

Double Buffering (DBMOD/SSTAT.7 = 1), Early Interrupt (INTLO/SSTAT.6 = 0) is Shown, With

Ending Tx Interrupt (DBISEL/SSTAT.4 = 1)

Figure 8-8: Transmission with and without Double Buffering

THE 9TH BIT (BIT 8) IN DOUBLE BUFFERING (MODES 1, 2 AND 3)

If double buffering is disabled (DBMOD, i.e. SSTAT.7 = 0), TB8 can be written before or after SBUF is written, provided TB8 is updated before that TB8 is shifted out. TB8 must not be changed again until after TB8 shifting has been completed, as indicated by the Tx interrupt.

If double buffering is enabled, TB8 MUST be updated before SBUF is written, as TB8 will be double-buffered together with SBUF data. The operation described in the section "Transmit Interrupts with Double Buffering Enabled (Modes 1, 2 and 3)" becomes as follows:

1. The double buffer is empty initially.

2. The CPU writes to TB8.

3. The CPU writes to SBUF.

4. The SBUF/TB8 data is loaded to the shift register and a Tx interrupt is generated immediately.

5. If there is more data, go to 7, else continue on 6.

6. If there is no more data, then:

- If DBISEL is ’0’, no more interrupt will occur.

- If DBISEL is ’1’ and INTLO is ’0’, a Tx interrupt will occur at the beginning of the STOP bit of the data currently in the shifter (which is also the last data).

2003 Dec 8 67

Philips Semiconductors

User’s Manual - Preliminary -

UART

- If DBISEL is ’1’ and INTLO is ’1’, a Tx interrupt will occur at the end of the STOP bit of the data currently in the shifter (which is also the last data).

7. If there is more data, the CPU writes to TB8 again.

8. The CPU writes to SBUF again. Then:

- If INTLO is ’0’, the new data will be loaded and a Tx interrupt will occur at the beginning of the STOP bit of the data currently in the shifter.

- If INTLO is ’1’, the new data will be loaded and a Tx interrupt will occur at the end of the STOP bit of the data currently in the shifter.

Go to 4.

P89LPC906/907/908

MULTIPROCESSOR COMMUNICATIONS

UART modes 2 and 3 have a special provision for multiprocessor communications. In these modes, 9 data bits are received or transmitted. When data is received, the 9th bit is stored in RB8. The UART can be programmed such that when the stop bit is received, the serial port interrupt will be activated only if RB8 = 1. This feature is enabled by setting bit SM2 in SCON. One way to use this feature in multiprocessor systems is as follows:

When the master processor wants to transmit a block of data to one of several slaves, it first sends out an address byte which identifies the target slave. An address byte differs from a data byte in that the 9th bit is 1 in an address byte and 0 in a data byte. With SM2 = 1, no slave will be interrupted by a data byte. An address byte, however, will interrupt all slaves, so that each slave can examine the received byte and see if it is being addressed. The addressed slave will clear its SM2 bit and prepare to receive the data bytes that follow. The slaves that weren’t being addressed leave their SM2 bits set and go on about their business, ignoring the subsequent data bytes.

Note that SM2 has no effect in Mode 0, and must be ’0’ in Mode 1.

AUTOMATIC ADDRESS RECOGNITION

Automatic Address Recognition is a feature which allows the UART to recognize certain addresses in the serial bit stream by using hardware to make the comparisons. This feature saves a great deal of software overhead by eliminating the need for the software to examine every serial address which passes by the serial port. This feature is enabled by setting the SM2 bit in SCON. In the 9 bit UART modes (mode 2 and mode 3), the Receive Interrupt flag (RI) will be automatically set when the received byte contains either the “Given” address or the “Broadcast” address. The 9 bit mode requires that the 9th information bit is a 1 to indicate that the received information is an address and not data.

Using the Automatic Address Recognition feature allows a master to selectively communicate with one or more slaves by invoking the Given slave address or addresses. All of the slaves may be contacted by using the Broadcast address. Two special Function Registers are used to define the slave’s address, SADDR, and the address mask, SADEN. SADEN is used to define which bits in the SADDR are to be used and which bits are “don’t care”. The SADEN mask can be logically ANDed with the SADDR to create the “Given” address which the master will use for addressing each of the slaves. Use of the Given address allows multiple slaves to be recognized while excluding others. The following examples will help to show the versatility of this scheme:

Slave 0 SADDR = 1100 0000

SADEN = 1111 1101 Given = 1100 00X0

Slave 1 SADDR = 1100 0000

SADEN = 1111 1110 Given = 1100 000X

In the above example SADDR is the same and the SADEN data is used to differentiate between the two slaves. Slave 0 requires a 0 in bit 0 and it ignores bit 1. Slave 1 requires a 0 in bit 1 and bit 0 is ignored. A unique address for Slave 0 would be 1100 0010

2003 Dec 8 68

Philips Semiconductors

User’s Manual - Preliminary -

UART

since slave 1 requires a 0 in bit 1. A unique address for slave 1 would be 1100 0001 since a 1 in bit 0 will exclude slave 0. Both slaves can be selected at the same time by an address which has bit 0 = 0 (for slave 0) and bit 1 = 0 (for slave 1). Thus, both could be addressed with 1100 0000.

In a more complex system the following could be used to select slaves 1 and 2 while excluding slave 0:

Slave 0 SADDR = 1100 0000

SADEN = 1111 1001 Given = 1100 0XX0

Slave 1 SADDR = 1110 0000

SADEN = 1111 1010 Given = 1110 0X0X

Slave 2 SADDR = 1110 0000

SADEN = 1111 1100 Given = 1110 00XX

In the above example the differentiation among the 3 slaves is in the lower 3 address bits. Slave 0 requires that bit 0 = 0 and it can be uniquely addressed by 1110 0110. Slave 1 requires that bit 1 = 0 and it can be uniquely addressed by 1110 and 0101. Slave 2 requires that bit 2 = 0 and its unique address is 1110 0011. To select Slaves 0 and 1 and exclude Slave 2 use address 1110 0100, since it is necessary to make bit 2 = 1 to exclude slave 2. The Broadcast Address for each slave is created by taking the logical OR of SADDR and SADEN. Zeros in this result are treated as don’t-cares. In most cases, interpreting the don’t-cares as ones, the broadcast address will be FF hexadecimal. Upon reset SADDR and SADEN are loaded with 0s. This produces a given address of all “don’t cares” as well as a Broadcast address of all “don’t cares”. This effectively disables the Automatic Addressing mode and allows the microcontroller to use standard UART drivers which do not make use of this feature.

P89LPC906/907/908

2003 Dec 8 69

Philips Semiconductors

User’s Manual - Preliminary -

UART

P89LPC906/907/908

2003 Dec 8 70

Philips Semiconductors

User’s Manual - Preliminary -

RESET

P89LPC906/907/908

9. RESET

The P1.5/RST pin can function as either an active low reset input or as a digital input, P1.5. The RPE (Reset Pin Enable) bit in UCFG1, when set to 1, enables the external reset input function on P1.5. When cleared, P1.5 may be used as an input pin.

NOTE: During a power-on sequence, The RPE selection is overriden and this pin will always functions as a reset input. An external circuit connected to this pin should not hold this pin low during a Power-on sequence as this will keep the device in reset. After power-on this input will function either as an external reset input or as a digital input as defined by the RPE bit. Only a poweron reset will temporarily override the selection defined by RPE bit. Other sources of reset will not override the RPE bit.

NOTE: During a power cycle, V

must fall below V

reapplied, in order to ensure a power-on reset.

Reset can be triggered from the following sources (see Figure 9-1):

• External reset pin (during power-on or if user configured via UCFG1);

• Power-on Detect;

• Brownout Detect;

• Watchdog Timer;

• Software reset;

• UART break-character detect reset. (P89LPC908)

For every reset source, there is a flag in the Reset Register, RSTSRC. The user can read this register to determine the most recent reset source. These flag bits can be cleared in software by writing a ’0’ to the corresponding bit. More than one flag bit may be set:

• During a power-on reset, both POF and BOF are set but the other flag bits are cleared.

• For any other reset, any previously set flag bits that have not been cleared will remain set.

(see "DC electrical characteristics" in the datasheet) before pwoer is

POR

POWER-ON RESET CODE EXECUTION

The P89LPC906/907/908 contains two special Flash elements: the BOOT VECTOR and the Boot Status Bit. Following reset, the device examines the contents of the Boot Status Bit. If the Boot Status Bit is set to zero, power-up execution starts at location 0000H, which is the normal start address of the user’s application code. When the Boot Status Bit is set to a one, the contents of the Boot Vector is used as the high byte of the execution address and the low byte is set to 00H. The factory default setting is 00H. A UART break-detect reset (P89LPC908) will have the same effect as a non-zero Status Bit.

RPE (UCFG1.6)

RST

WDTE (UCFG1.7)

Watchdog Timer Reset

Software Reset SRST (AUXR1.3)

Power-on Detect

UART Break Detect

EBRR (AUXR1.6)

Brownout Detect Reset

BOPD (PCON.5)

Figure 9-1: Block Diagram of Reset

Chip Reset

2003 Dec 8 71

Philips Semiconductors

User’s Manual - Preliminary -

RESET

RSTSRC

Address: DFH

Not bit addressable

Reset Sources: Power-on only

Reset Value: xx110000B (This is the power-on reset value. Other reset sources will set corresponding bits.)

BIT SYMBOL FUNCTION

RSTSRC.7-6 - Reserved for future use. Should not be set to 1 by user programs.

RSTSRC.5 BOF Brownout Detect Flag. When Brownout Detect is activated, this bit is set. It will remain set

RSTSRC.4 POF Power-on Detect Flag. When Power-on Detect is activated, the POF flag is set to indicate

RSTSRC.3 R_BK Break detect reset. If a break detect occurs and EBRR (AUXR1.6) is set to ’1’, a system

RSTSRC.2 R_WD Watchdog Timer reset flag. Cleared by software by writing a ’0’ to the bit or a Power-on

RSTSRC.1 R_SF Software reset Flag. Cleared by software by writing a ’0’ to the bit or a Power-on reset.

RSTSRC.0 R_EX External reset Flag. When this bit is ’1’, it indicates external pin reset. Cleared by software

76543210

- - BOF POF R_BK R_WD R_SF R_EX

until cleared by software by writing a ’0’ to the bit. (Note: On a Power-on reset, both POF and this bit will be set while the other flag bits are cleared.)

an initial power-up condition. The POF flag will remain set until cleared by software by writing a ’0’ to the bit.. (Note: On a Power-on reset, both BOF and this bit will be set while the other flag bits are cleared.)

reset will occur. This bit is set to indicate that the system reset is caused by a break detect. Cleared by software by writing a ’0’ to the bit or on a Power-on reset. (P89LPC908)

reset.(NOTE: UCFG1.7 must be = 1).

by writing a ’0’ to the bit or a Power-on reset. If RST reset is over, R_EX will be set.

is still asserted after the Power-on

P89LPC906/907/908

Figure 9-2: Reset Sources Register

2003 Dec 8 72

Philips Semiconductors

User’s Manual - Preliminary -

ANALOG COMPARATORS

P89LPC906/907/908

10. ANALOG COMPARATORS

An analog comparator is provided on the P89LPC906/907/908 . Comparator operation is such that the output is a logical one when the positive input is greater than the negative input (selectable from a pin or an internal reference voltage). Otherwise the output is a zero. The output may be read in a register. The output may also be routed to a pin. The comparator may be configured to cause an interrupt when the output value changes.

The connections to the comparator are shown in Figure 10-2. The comparator functions to V

When the comparator is first enabled, the comparator output and interrupt flag are not guaranteed to be stable for 10 microseconds. The comparator interrupt should not be enabled during that time, and the comparator interrupt flag must be cleared before the interrupt is enabled in order to prevent an immediate interrupt service.

COMPARATOR CONFIGURATION

The comparator control register, CMP1, is shown in Figure 10-1. The possible configurations for the comparator are shown in Figure 10-3.

CMP1

Address: ACh

Not bit addressable

Reset Source(s): Any reset

Reset Value: xx000000B

BIT SYMBOL FUNCTION

CMP.7, 6 - Reserved for future use.

CMP.5 CE1 Comparator enable. When set, the comparator function is enabled. Comparator output is

CMP.4 - Reserved for future use.

CMP.3 CN1 Comparator negative input select. When 0, the comparator reference pin CMPREF is

CMP.2 OE1 Output enable. When 1, the comparator output is connected to the CMP1 pin if the

CMP.1 CO1 Comparator output, synchronized to the CPU clock to allow reading by software.

CMP.0 CMF1 Comparator interrupt flag. This bit is set by hardware whenever the comparator output

76543210

- - CE1 - CN1 OE1 CO1 CMF1

stable 10 microseconds after CE1 is set.

selected as the negative comparator input. When 1, the internal comparator reference, Vref, is selected as the negative comparator input.

comparator is enabled (CE1 = 1). This output is asynchronous to the CPU clock.

COn changes state. This bit will cause a hardware interrupt if enabled. Cleared by software.

= 2.4V.

Figure 10-1: Comparator Control Register (CMP1)

2003 Dec 8 73

Philips Semiconductors

User’s Manual - Preliminary -

ANALOG COMPARATORS

Comparator 1

(P0.4) CIN1A

(P0.5) CMPREF

CMPREF

Vref

CIN1A

CN1

Figure 10-2: Comparator Input and Output Connections

CN1, OE1 = 0 0

CO1

Change Detect

OE1

CIN1A

CMPREF

P89LPC906/907/908

CMF1

CN1, OE1 = 0 1

CMP1 (P0.6)

CO1

Interrupt

CMP1

CN1, OE 1= 1 1CN1, OE1 = 1 0

CIN1A

Vref (1.23V)

CO1

Figure 10-3: Comparator Configurations

CIN1A

Vref (1.23V)

CO1

CMP1

INTERNAL REFERENCE VOLTAGE

An internal reference voltage, Vref, may supply a default reference when a single comparator input pin is used. Please refer to the Datasheet for specifications.

COMPARATOR INTERRUPT

The comparator has an interrupt flag, CMF1, contained in its configuration register. This flag is set whenever the comparator output changes state. The flag may be polled by software or may be used to generate an interrupt. The interrupt will be generated when the interrupt enable bit EC in the IEN1 register is set and the interrupt system is enabled via the EA bit in the IEN0 register.

When a comparator is disabled the comparator’s output, COx, goes high. If the comparator output was low and then is disabled, the resulting transition of the comparator output from a low to high state will set the the comparator flag, CMFx. This will cause an interrupt if the comparator interrupt is enabled. The user should therefore disable the comparator interrupt prior to disabling the comparator. Additionally, the user should clear the comparator flag, CMFx, after disabling the comparator.

COMPARATOR AND POWER REDUCTION MODES

The comparator(s) may remain enabled when Power down or Idle mode is activated, but the comparator(s) are disabled automatically in Total Power down mode.

If the comparator interrupt is enabled (except in Total Power down mode), a change of the comparator output state will generate an interrupt and wake up the processor.

2003 Dec 8 74

Philips Semiconductors

User’s Manual - Preliminary -

ANALOG COMPARATORS

If the comparator output to a pin is enabled, the pin should be configured in the push-pull mode in order to obtain fast switching times while in power down mode. The reason is that with the oscillator stopped, the temporary strong pullup that normally occurs during switching on a quasi-bidirectional port pin does not take place.

The comparator consumes power in Power down and Idle modes, as well as in the normal operating mode. This fact should be taken into account when system power consumption is an issue. To minimize power consumption, the user can disable the comparator via PCONA.5 or put the device in Total Power down mode.

P89LPC906/907/908

COMPARATOR CONFIGURATION EXAMPLE

The code shown below is an example of initializing the comparator. This comparator is configured to use the CMPREF inputs. The comparator output drives the CMP pin and generates an interrupt when the comparator output changes.

CMPINIT:

MOV PT0AD,#030h ; Disable digital INPUTS on pins that are used

; for analog functions: CIN, CMPREF.

ANL P0M2,#0CFh ; Disable digital OUTPUTS on pins that are used

ORL P0M1,#030h ; for analog functions: CIN, CMPREF.

MOV CMP1,#024h ; Turn on comparator and set up for:

; - Negative input from CMPREF pin.

; - Output to CMP pin enabled.

CALL delay10us ; The comparator has to start up for at

; least 10 microseconds before use.

ANL CMP1,#0FEh ; Clear comparator interrupt flag.

SETB EC ; Enable the comparator interrupt. The

; priority is left at the current value.

SETB EA ; Enable the interrupt system (if needed).

RET ; Return to caller.

The interrupt routine used for the comparator must clear the interrupt flag (CMF1 in this case) before returning.

2003 Dec 8 75

Philips Semiconductors

User’s Manual - Preliminary -

ANALOG COMPARATORS

P89LPC906/907/908

2003 Dec 8 76

Philips Semiconductors

User’s Manual - Preliminary -

KEYPAD INTERRUPT (KBI)

P89LPC906/907/908

11. KEYPAD INTERRUPT (KBI)

The Keypad Interrupt function is intended primarily to allow a single interrupt to be generated when the Port 0 bits are equal to or not equal to a certain pattern. This function can be used for keypad recognition. The user can configure the port via SFRs for different tasks.

There are three SFRs used for this function. The Keypad Interrupt Mask Register (KBMASK) is used to define which input pins connected to Port 0 are enabled to trigger the interrupt. The Keypad Pattern Register (KBPATN) is used to define a pattern that is compared to the value of Port 0. The Keypad Interrupt Flag (KBIF) in the Keypad Interrupt Control Register (KBCON) is set when the condition is matched while the Keypad Interrupt function is active. An interrupt will be generated if it has been enabled by setting the EKBI bit in IEN1 register and EA = 1. The PATN_SEL bit in the Keypad Interrupt Control Register (KBCON) is used to define equal or not-equal for the comparison.

In order to use the Keypad Interrupt as an original KBI function like in the 87LPC76x series, the user needs to set KBPATN = 0FFH and PATN_SEL = 0 (not equal), then any key connected to Port0 which is enabled by KBMASK register will cause the hardware to set KBIF = 1 and generate an interrupt if it has been enabled. The interrupt may be used to wake up the CPU from Idle or Power down modes. This feature is particularly useful in handheld, battery powered systems that need to carefully manage power consumption yet also need to be convenient to use.

In order to set the flag and and cause an interrupt, the pattern on Port 0 must be held longer than 6 CCLKs.

KBPATN

Address: 93h

Not bit addressable

Reset Source(s): Any reset

Reset Value: 11111111B

BIT SYMBOL FUNCTION

KBPATN.6,5,4 - Pattern bits 6,5,4

76543210

KBPATN.6 KBPATN.5 KBPATN.4 - - - -

Figure 11-1: Keypad Pattern Register

KBCON

Address: 94h

Not bit addressable

Reset Source(s): Any reset

Reset Value: xxxxxx00B

BIT SYMBOL FUNCTION

KBCON.7-2 - Reserved

KBCON.1 PATN_SEL Pattern Matching Polarity selection. When set, Port 0 has to be equal to the user-defined

Pattern in KBPATN to generate the interrupt. When clear, Port 0 has to be not equal to the value of KBPATN register to generate the interrupt.

KBCON.0 KBIF Keypad Interrupt Flag. Set when Port 0 matches user defined conditions specified in

KBPATN, KBMASK, and PATN_SEL. Needs to be cleared by software by writing "0".

2003 Dec 8 77

76543210

------PATN_SEL KBIF

Figure 11-2: Keypad Control Register

Philips Semiconductors

User’s Manual - Preliminary -

KEYPAD INTERRUPT (KBI)

KBMASK

Address: 86h

Not bit addressable

Reset Source(s): Any reset

Reset Value: 00000000B

BIT SYMBOL FUNCTION

KBMASK.7 - Reserved.

KBMASK.6 - When set, enables P0.6 as a cause of a Keypad Interrupt.

KBMASK.5 - When set, enables P0.5 as a cause of a Keypad Interrupt.

KBMASK.4 - When set, enables P0.4 as a cause of a Keypad Interrupt.

KBMASK.3:0 - Reserved.

Note: the Keypad Interrupt must be enabled in order for the settings of the KBMASK register to be effective.

Bits positions KBMASK.7, KBMASK.3, KBMASK.2, KBMASK.1, and KBMASK.0 should always be written as a ’0’.

76543210

- KBMASK.6 KBMASK.5 KBMASK.4 - - - -

Figure 11-3: Keypad Interrupt Mask Register (KBM)

P89LPC906/907/908

2003 Dec 8 78

Philips Semiconductors

User’s Manual - Preliminary -

WATCHDOG TIMER

P89LPC906/907/908

12. WATCHDOG TIMER

The watchdog timer subsystem protects the system from incorrect code execution by causing a system reset when it underflows as a result of a failure of software to feed the timer prior to the timer reaching its terminal count. The watchdog timer can only be reset by a power-on reset.

WATCHDOG FUNCTION

The user has the ability using the WDCON and UCFG1 registers to control the run /stop condition of the WDT, the clock source for the WDT, the prescaler value, and whether the WDT is enabled to reset the device on underflow. In addition, there is a safety mechanism which forces the WDT to be enabled by values programmed into UCFG1 either through IAP or a commercial programmer.

The WDTE bit (UCFG1.7), if set, enables the WDT to reset the device on underflow. Following reset, the WDT will be running regardless of the state of the WDTE bit.

The WDRUN bit (WDCON.2) can be set to start the WDT and cleared to stop the WDT. Following reset this bit will be set and the WDT will be running. All writes to WDCON need to be followed by a feed sequence (see section "Feed Sequence" on page

80). Additional bits in WDCON allow the user to select the clocksource for the WDT and the prescaler.

When the timer is not enabled to reset the device on underflow, the WDT can be used in "timer mode" and be enabled to produce an interrupt (IEN0.6) if desired.

The Watchdog Safety Enable bit, WDSE (UCFG1.4) along with WDTE, is designed to force certain operating conditions at powerup. Refer to the Table for details

Table 12-1: .Watchdog timer configuration

WDTE

(UCFG1.7)

WDSE

(UCFG1.4)

FUNCTION

The watchdog reset is disabled. The timer can be used as an internal timer and can be used to generate an interrupt. WDSE has no effect.

Figure 12-3 shows the watchdog timer in watchdog mode. It consists of a programmable 13-bit prescaler, and an 8-bit down counter. The down counter is clocked (decremented) by a tap taken from the prescaler. The clock source for the prescaler is either PCLK or the watchdog oscillator selected by the WDCLK bit in the WDCON register. (Note that switching of the clock sources will not take effect immediately - see section "Watchdog Clock Source" on page 84).

The watchdog asserts the watchdog reset when the watchdog count underflows and the watchdog reset is enabled. When the watchdog reset is enabled, writing to WDL or WDCON must be followed by a feed sequence for the new values to take effect.

If a watchdog reset occurs, the internal reset is active for at least one watchdog clock cycle (PCLK or the watchdog oscillator clock). If CCLK is still running, code execution will begin immediately after the reset cycle. If the processor was in Power down mode, the watchdog reset will start the oscillator and code execution will resume after the oscillator is stable.

The watchdog reset is enabled. The user can set WDCLK to choose the clock source.

The watchdog reset is enabled, along with additional safety features:

1. WDCLK is forced to 1 (using watchdog oscillator)

2. WDCON and WDL register can only be written once

3. WDRUN is forced to 1and cannot be cleared by software.

2003 Dec 8 79

Philips Semiconductors

User’s Manual - Preliminary -

WATCHDOG TIMER

P89LPC906/907/908

Watchdog Oscillator

÷32

÷2 ÷2 ÷2 ÷2 ÷2 ÷2 ÷2

PCLK

÷32 ÷64 ÷128 ÷256 ÷512 ÷1024 ÷2048 ÷4096

WDCLK after a

watchdog feed

sequence

TO WATCHDOG DOWN COUNTER (after one prescaler count delay

PRE2

PRE1

PRE0

DECODE

000 001

010 011

100 101

110

111

Figure 12-1: Watchdog Prescaler

FEED SEQUENCE

The watchdog timer control register and the 8-bit down counter (Figure 12-3) are not directly loaded by the user. The user writes to the WDCON and the WDL SFRs. At the end of a feed sequence, the values in the WDCON and WDL SFRs are loaded to the control register and the 8-bit down counter. Before the feed sequence, any new values written to these two SFRs will not take effect. To avoid a watchdog reset, the watchdog timer needs to be fed (via a special sequence of software action called the feed sequence) prior to reaching an underflow.

To feed the watchdog, two write instructions must be sequentially executed successfully. Between the two write instructions, SFR reads are allowed, but writes are not allowed. The instructions should move A5H to the WFEED1 register and then 5AH to the WFEED2 register. An incorrect feed sequence will cause an immediate watchdog reset. The program sequence to feed the watchdog timer is as follows:

CLR EA ; disable interrupt

MOV WFEED1,#0A5h ; do watchdog feed part 1

MOV WFEED2,#05Ah ; do watchdog feed part 2

SETB EA ; enable interrupt

This sequence assumes that the P89LPC906/907/908 interrupt system is enabled and there is a possibility of an interrupt request occuring during the feed sequence. If an interrupt was allowed to be serviced and the service routine contained any SFR writes, it would trigger a watchdog reset. If it is known that no interrupt could occur during the feed sequence, the instructions to disable and re-enable interrupts may be removed.

In watchdog mode (WDTE = 1), writing the WDCON register must be IMMEDIATELY followed by a feed sequence to load the WDL to the 8-bit down counter, and the WDCON to the shadow register. If writing to the WDCON register is not immediately followed by the feed sequence, a watchdog reset will occur.

For example: setting WDRUN = 1:

MOV ACC,WDCON ; get WDCON

SETB ACC.2 ; set WD_RUN=1

MOV WDL,#0FFh ; New count to be loaded to 8-bit down counter

CLR EA ; disable interrupt

MOV WDCON,ACC ; write back to WDCON (after the watchdog is enabled, a feed must occur

; immediately)

2003 Dec 8 80

Philips Semiconductors

User’s Manual - Preliminary -

WATCHDOG TIMER

MOV WFEED1,#0A5h ; do watchdog feed part 1

MOV WFEED2,#05Ah ; do watchdog feed part 2

SETB EA ; enable interrupt

In timer mode (WDTE = 0), WDCON is loaded to the control register every CCLK cycle (no feed sequence is required to load the control register), but a feed sequence is required to load from the WDL SFR to the 8-bit down counter before a time-out occurs.

WDCON

Address: A7h

Not bit addressable

Reset Source(s): See reset value below

Reset Value: 111xx1?1B (Note: WDCON.7,6,5,2,0 - set to ’1’ any reset; WDCON.1 - cleared to ’0’ on Power-on

BIT SYMBOL FUNCTION

WDCON.7-5 PRE2-PRE0 Clock Prescaler Tap Select. Refer to Table for details.

WDCON.4-3 - Reserved for future use. Should not be set to 1 by user program.

WDCON.2 WDRUN Watchdog Run Control. The watchdog timer is started when WDRUN = 1 and stopped

WDCON.1 WDTOF Watchdog Timer Time-Out Flag. This bit is set when the 8-bit down counter underflows.

WDCON.0 WDCLK Watchdog input clock select. When set, the watchdog oscillator is selected. When cleared,

76543210

PRE2 PRE1 PRE0 - - WDRUN WDTOF WDCLK

reset, set to ’1’ on watchdog reset, not affected by any other reset)

when WDRUN = 0. This bit is forced to 1 (watchdog running) and cannot be cleared by software if both WDTE and WDSE are set to 1.

In watchdog mode, a feed sequence will clear this bit. It can also be cleared by writing ’0’ to this bit in software.

PCLK is selected. (If the CPU is powered down, the watchdog is disabled if WDCLK = 0, see section "Power down operation"). (Note: If both WDTE and WDSE are set to 1, this bit is forced to 1.) Refer to section "Watchdog Clock Source" for details.

P89LPC906/907/908

Figure 12-2: Watchdog Timer Control Register

The number of watchdog clocks before timing out is calculated by the following equations:

(5+PRE)

tclks = (2

where:

• PRE is the value of prescaler (PRE2-PRE0) which can be the range 0-7, and;

• WDL is the value of watchdog load register which can be the range of 0-255.

The minimum number of tclks is:

tclks = (2

The maximum number of tclks is:

tclks = (2

The following table shows sample P89LPC906/907/908 timeout values.

2003 Dec 8 81

)(WDL+1)+1

(5+0)

)(0+1)+1 = 33

(5+7)

)(255+1)+1 = 1,048,577

Philips Semiconductors

User’s Manual - Preliminary -

WATCHDOG TIMER

Table 12-2: P89LPC906/907/908 Watchdog Timeout Values

Timeout Period

PRE2-PRE0 WDL in decimal)

000

001

010

011

100

101

110

111

0 33 82.5µs 5.50µs

255 8,193 20.5ms 1.37ms

0 65 162.5µs 10.8µs

255 16,385 41.0ms 2.73ms

0 129 322.5µs 21.5µs

255 32,769 81.9ms 5.46ms

0 257 642.5µs 42.8µs

255 65,537 163.8ms 10.9ms

0 513 .1.28ms 85.5µs

255 131,073 327.7ms 21.8ms

0 1,025 2.56ms 170.8µs

255 262,145 655.4ms 43.7ms

0 2,049 5.12ms 341.5µs

255 524,289 1.31s 87.4ms

0 4097 10.2ms 682.8µs

255 1,048,577 2.62s 174.8ms

(in watchdog clock

cycles)

400KHz Watchdog Oscillator Clock

(Nominal)

P89LPC906/907/908

Watchdog Clock Source

12MHz CCLK (6MHz CCLK/2

Watchdog Clock)

2003 Dec 8 82

Philips Semiconductors

User’s Manual - Preliminary -

WATCHDOG TIMER

MOV WFEED1, #0A5H MOV WFEED2, #05AH

Watchdog

Oscillator

PCLK

÷32

PRESCALER

PRE2 PRE1 PRE0 WDRUN WDTOF WDCLK

control register

WDL (C1H)

8-Bit Down

Counter

P89LPC906/907/908

Watchdog reset can also be caused

by an invalid feed sequence, or by

writing to WDCON not immediately

followed by a feed sequence

WDCON(A7H)

RESET

SHADOW

WDCON

Figure 12-3: Watchdog Timer in Watchdog Mode (WDTE = 1)

WATCHDOG TIMER IN TIMER MODE

Figure 12-4 shows the Watchdog Timer in Timer Mode. In this mode, any changes to WDCON are written to the shadow register after one watchdog clock cycle. A watchdog underflow will set the WDTOF bit. If IEN0.6 is set, the watchdog underflow is enabled to cause an interrupt. WDTOF is cleared by writing a '0' to this bit in software. When an underflow occurs, the contents of WDL is reloaded into the down counter and the watchdog timer immediately begins to count down again.

A feed is necessary to cause WDL to be loaded into the down counter before an underflow occurs. Incorrect feeds are ignored in this mode.

2003 Dec 8 83

Philips Semiconductors

User’s Manual - Preliminary -

WATCHDOG TIMER

MOV WFEED1, #0A5H MOV WFEED2, #05AH

Watchdog

Oscillator

CLK

÷32

PRESCALER

PRE2 PRE1 PRE0 WDRUN WDTOF WDCLK

control register

WDL (C1H)

8-Bit Down

Counter

P89LPC906/907/908

Interrupt

SHADOW

WDCON

WDCON(A7H)

Figure 12-4: Watchdog Timer in Timer Mode (WDTE = 0)

POWER DOWN OPERATION

The WDT oscillator will continue to run in power down, consuming approximately 50uA, as long as the WDT oscillator is selected as the clock source for the WDT. Selecting PCLK as the WDT source will result in the WDT oscillator going into power down with the rest of the device (see section "Watchdog Clock Source", below ). Power down mode will also prevent PCLK from running and therefore the watchdog is effectively disabled.

WATCHDOG CLOCK SOURCE

The watchdog timer system has an on-chip 400KHz oscillator. The watchdog timer can be clocked from either the watchdog oscillator or from PCLK (refer to Figure 12-1) by configuring the WDCLK bit in the Watchdog Control Register WDCON. When the watchdog feature is enabled, the timer must be fed regularly by software in order to prevent it from resetting the CPU.

After changing WDCLK (WDCON.0), switching of the clock source will not immediately take effect. As shown in Figure 12-3, the selection is loaded after a watchdog feed sequence. In addition, due to clock synchronization logic, it can take two old clock cycles before the old clock source is deselected, and then an additional two new clock cycles before the new clock source is selected.

Since the prescaler starts counting immediately after a feed, switching clocks can cause some inaccuracy in the prescaler count. The inaccuracy could be as much as 2 old clock source counts plus 2 new clock cycles.

Note: When switching clocks, it is important that the old clock source is left enabled for 2 clock cycles after the feed completes. Otherwise, the watchdog may become disabled when the old clock source is disabled. For example, suppose PCLK (WCLK=0) is the current clock source. After WCLK is set to ’1’, the program should wait at least two PCLK cycles (4 CCLKs) after the feed completes before going into Power down mode. Otherwise, the watchdog could become disabled when CCLK turns off. The watchdog oscillator will never become selected as the clock source unless CCLK is turned on again first.

2003 Dec 8 84

Philips Semiconductors

User’s Manual - Preliminary -

WATCHDOG TIMER

P89LPC906/907/908

PERIODIC WAKEUP FROM POWER DOWN WITHOUT AN EXTERNAL OSCILLATOR

Without using an external oscillator source, the power consumption required in order to have a periodic wakeup is determined by the power consumption of the internal oscillator source used to produce the wakeup.The Real-time clock running from the internal RC oscillator can be used. The power consumption of this oscillator is approximately 300uA. Instead, if the WDT is used to generate interrupts the current is reduced to approximately 50uA. Whenever the WDT underflows, the device will wake up.

2003 Dec 8 85

Philips Semiconductors

User’s Manual - Preliminary -

WATCHDOG TIMER

P89LPC906/907/908

2003 Dec 8 86

Philips Semiconductors

User’s Manual - Preliminary -

ADDITIONAL FEATURES

P89LPC906/907/908

13. ADDITIONAL FEATURES

The AUXR1 register contains several special purpose control bits that relate to several chip features. AUXR1 is described in Figure 13-1.

AUXR1

Address: A2h

Not bit addressable

Reset Source(s): Any reset

Reset Value: 000000x0B

BIT SYMBOL FUNCTION

AUXR1.7 CLKLP Clock Low Power Select. When set, reduces power consumption in the clock circuits. Can

AUXR1.6 EBRR UART Break Detect Reset Enable. If ’1’, UART Break Detect will cause a chip reset

76543210

CLKLP EBRR - - SRST 0 - DPS

be used when the clock frequency is 8MHz or less. After reset this bit is cleared to support up to 12MHz operation (P89LPC906).

(P89LPC908). When writing to this register on the P89LPC906 or P89LPC907 devices, this bit position should be written with a zero.

AUXR1.5 - Reserved

AUXR1.4 - Reserved

AUXR1.3 SRST Software Reset. When set by software, resets the P89LPC906/907/908 as if a hardware

reset occurred.

AUXR1.2 0 This bit contains a hard-wired 0. Allows toggling of the DPS bit by incrementing AUXR1,

without interfering with other bits in the register.

AUXR1.1 - Not used. Allowable to set to a "1" .

AUXR1.0 DPS Data Pointer Select. Chooses one of two Data Pointers.

Figure 13-1: AUXR1 Register

SOFTWARE RESET

The SRST bit in AUXR1 gives software the opportunity to reset the processor completely, as if an external reset or watchdog reset had occurred. If a value is written to AUXR1 that contains a 1 at bit position 3, all SFRs will be initialized and execution will resume at program address 0000. Care should be taken when writing to AUXR1 to avoid accidental software resets.

DUAL DATA POINTERS

The dual Data Pointers (DPTR) adds to the ways in which the processor can specify the address used with certain instructions. The DPS bit in the AUXR1 register selects one of the two Data Pointers. The DPTR that is not currently selected is not accessible to software unless the DPS bit is toggled.

Specific instructions affected by the Data Pointer selection are:

• INC DPTR Increments the Data Pointer by 1.

• JMP @A+DPTR Jump indirect relative to DPTR value.

2003 Dec 8 87

Philips Semiconductors

User’s Manual - Preliminary -

ADDITIONAL FEATURES

• MOV DPTR, #data16 Load the Data Pointer with a 16-bit constant.

• MOVCA, @A+DPTR Move code byte relative to DPTR to the accumulator.

• MOVXA, @DPTR Move data byte the accumulator to data memory relative to DPTR.

• MOVX@DPTR, A Move data byte from data memory relative to DPTR to the accumulator.

Also, any instruction that reads or manipulates the DPH and DPL registers (the upper and lower bytes of the current DPTR) will be affected by the setting of DPS. The MOVX instructions have limited application for the P89LPC906/907/908 since the part does not have an external data bus. However, they may be used to access Flash configuration information (see Flash Configuration section).

Bit 2 of AUXR1 is permanently wired as a logic 0. This is so that the DPS bit may be toggled (thereby switching Data Pointers) simply by incrementing the AUXR1 register, without the possibility of inadvertently altering other bits in the register.

P89LPC906/907/908

2003 Dec 8 88

Philips Semiconductors

User’s Manual - Preliminary -

FLASH PROGRAM MEMORY

P89LPC906/907/908

14. FLASH PROGRAM MEMORY

GENERAL DESCRIPTION

The P89LPC906/907/908 Flash memory provides in-circuit electrical erasure and programming. The Flash can be read and written as bytes. On-chip erase and write timing generation contribute to a user-friendly programming interface. The cell is designed to optimize the erase and programming mechanisms. The P89LPC906/907/908 uses VDD as the supply voltage to perform the Program/Erase algorithms. Additionally, serial programming using commercially available programmers provides a simple inteface to achieve in-circuit programming.The P89LPC906/907/908 Flash reliably stores memory contents after 100,000 erase and program cycles (typical).

FEATURES

• IAP-Lite allows individual and multiple bytes of code memory to be used for data storage.

• Programming and erase over the full operating voltage range

• Read/Programming/Erase using IAP-Lite

• Any flash program operation in 2 ms (4ms for erase/program)

• Serial programming with industry-standard commercial programmers allows in-circuit programming.

• Programmable security for the code in the Flash for each sector.

• >100,000 typical erase/program cycles for each byte.

• 256 byte sector size, 16 byte page size

• 10-year minimum data retention.

INTRODUCTION TO IAP-LITE

The Flash code memory array of this device supports IAP-Lite programming and erase functions. Any byte in a non-secured sector of the code memory array may be read using the MOVC instruction and thus is suitable for use as non-volatile data storage. In addition, the user’s code may access additional flash elements. These include UCFG1, the Boot Vector, Status Bit, security bytes, and signature bytes. Access of these elements uses a slightly different method than that used to access the user code memory.

USING FLASH AS DATA STORAGE

IAP-Lite provides an erase-program function that makes it easy for one or more bytes within a page to be erased and programmed in a single operation without the need to erase or program any other bytes in the page. IAP-Lite is performed in the application under the control of the microcontroller’s firmware using four SFRs and an internal 16-byte "page register" to facilitate erasing and programming within unsecured sectors. These SFRs are:

• FMCON (Flash Control Register). When read, this is the status register. When written, this is a command register. Note that the status bits are cleared to ’0’s when the command is written.

• FMDATA (Flash Data Register). Accepts data to be loaded into the page register.

• FMADRL, FMADRH (Flash memory address low, Flash memory address high). Used to specify the byte address within the page register or specify the page within user code memory.

The page register consists of 16 bytes and an update flag for each byte. When a LOAD command is issued to FMCON the page register contents and all of the update flags will be cleared. When FMDATA is written, the value written to FMDATA will be stored in the page register at the location specified by the lower 6 bits of FMADRL. In addition, the update flag for that location will be set. FMADRL will auto-increment to the next location. Auto-increment after writing to the last byte in the page register will

2003 Dec 8 89

Philips Semiconductors

User’s Manual - Preliminary -

FLASH PROGRAM MEMORY

"wrap -around" to the first byte in the page register, but will not affect FMADRL[7:4]. Bytes loaded into the page register do not have to be continuous. Any byte location can be loaded into the page register by changing the contents of FMADRL prior to writing to FMDATA. However, each location in the page register can only be written once following each LOAD command. Attempts to write to a page register location more than once should be avoided.

FMADRH and FMADRL[7:4] are used to select a page of code memory for the erase-program function. When the erase-program command is written to FMCON, the locations within the code memory page that correspond to updated locations in the page register will have their contents erased and programmed with the contents of their corresponding locations in the page register. Only the bytes that were loaded into the page register will be erased and programmed in the user code array. Other bytes within the user code memory will not be affected.

Writing the erase-program command (68H) to FMCON will start the erase-program process and place the CPU in a programidle state. The CPU will remain in this idle state until the erase-program cycle is either completed or terminated by an interrupt. When the program-idle state is exited, FMCON will contain status information for the cycle.

If an interrupt occurs during an erase/programming cycle, the erase/programming cycle will be aborted and the OI flag (Operation Interrupted) in FMCON will be set. If the application permits interrupts during erasing-programming, the user code should check the OI flag (FMCON.0) after each erase-programming operation to see if the operation was aborted. If the operation was aborted, the user’s code will need to repeat the process starting with loading the page register.

The erase-program cycle takes 4ms to complete, regardless of the number of bytes that were loaded into the page register.

P89LPC906/907/908

Erasing-programming of a single byte (or multiple bytes) in code memory is accomplished using the following steps:

• Write the LOAD command (00H) to FMCON. The LOAD command will clear all locations in the page register and their corresponding update flags.

• Write the address within the page register to FMADRL. Since the loading the page register uses FMADRL[5:0], and since the erase-program command uses FMADRH and FMADRL[7:4], the user can write the byte location within the page register (FMADRL[3:0]) and the code memory page address (FMADRH and FMADRL[7:4]) at this time.

• Write the data to be programmed to FMDATA. This will increment FMADRL pointing to the next byte in the page register.

• Write the address of the next byte to be programmed to FMADRL, if desired. (Not needed for contiguous bytes since FMADRL is auto-incremented). All bytes to be programmed must be within the same page.

• Write the data for the next byte to be programmed to FMDATA.

• Repeat writing of FMADRL and/or FMDATA until all desired bytes have been loaded into the page register.

• Write the page address in user code memory to FMADRH and FMADRL[7:4], if not previously included when writing the page register address to FMADRL[3:0].

• Write the erase-program command (68H) to FMCON,starting the erase-program cycle.

• Read FMCON to check status. If aborted, repeat starting with the LOAD command.

An assembly language routine to load the page register and perform an erase/program operation is shown in Figure 14-2. A similar C-language routine is shown in Figure 14-3.

2003 Dec 8 90

Philips Semiconductors

User’s Manual - Preliminary -

FLASH PROGRAM MEMORY

FMCON

Address: E4h

Not bit addressable

Reset Source(s): Any reset

Reset Value:

BIT SYMBOL FUNCTION

FMCON.7-4 - Reserved.

FMCON.3 HVA High voltage abort. Set if either an interrupt or a brown-out is detected during a program

FMCON.2 HVE High voltage error. Set when an error occurs in the high voltage generator.

FMCON.1 SV Security violation. Set when an attempt is made to program, erase, or CRC a secured

FMCON.0 OI Operation interrupted. Set when cycle aborted due to an interrupt or reset.

76543210

- - - - HVA HVE SV OI

or erase cycle. Also set if the brown-out detector is disabled at the start of a program or erase cycle.

sector or page.

Figure 14-1: Flash Memory Control Register

P89LPC906/907/908

;* Inputs: * ;* R3 = number of bytes to program (byte) * ;* R4 = page address MSB(byte) * ;* R5 = page address LSB(byte) * ;* R7 = pointer to data buffer in RAM(byte) * ;* Outputs: * ;* R7 = status (byte) * ;* C = clear on no error, set on error *

LOAD EQU 00H EP EQU 68H

PGM_USER: MOV FMCON,#LOAD ;load command, clears page register MOV FMADRH,R4 ;get high address MOV FMADRL,R5 ;get low address MOV A,R7 ; MOV R0,A ;get pointer into R0 LOAD_PAGE: MOV FMDAT,@R0 ;write data to page register INC R0 ;point to next byte DJNZ R3,LOAD_PAGE ;do until count is zero MOV FMCON,#EP ;else erase & program the page

MOV R7,FMCON ;copy status for return MOV A,R7 ;read status ANL A,#0FH ;save only four lower bits JNZ BAD ; CLR C ;clear error flag if good RET ;and return BAD: SETB C ;set error flag RET ;and return

2003 Dec 8 91

Philips Semiconductors

User’s Manual - Preliminary -

FLASH PROGRAM MEMORY

Figure 14-2: Assembly language routine to erase/program all or part of a page

P89LPC906/907/908

unsigned char idata dbytes[16]; // data buffer unsigned char Fm_stat; // status result

bit PGM_USER (unsigned char, unsigned char); bit prog_fail;

void main ()

{ prog_fail=PGM_USER(0x1F,0xC0); }

bit PGM_USER (unsigned char page_hi, unsigned char page_lo) { #define LOAD 0x00 // clear page register, enable loading #define EP 0x68 // erase & program page unsigned char i; // loop count

FMCON = LOAD; //load command, clears page reg FMADRH = page_hi; // FMADRL = page_lo; //write my page address to addr regs

for (i=0;i<16;i=i+1) { FMDATA = dbytes[i]; } FMCON = EP; //erase & prog page command Fm_stat = FMCON; //read the result status if ((Fm_stat & 0x0F)!=0) prog_fail=1; else prog_fail=0; return(prog_fail); }

Figure 14-3: C-language routine to erase/program all or part of a page

ACCESSING ADDITIONAL FLASH ELEMENTS

In addition to the user code array, the user’s firmware may access additional flash elements. These include UCFG1, the Boot Vector, Status Bit, and signature bytes. Access of these elements uses a slightly different method than that used to access the user code memory. Signature bytes are read-only. Security bytes may be erased only under certain conditions.

IAP-Lite is performed in the application under the control of the microcontroller’s firmware using four SFRs to facilitate erasing, programming, or reading. These SFRs are:

• FMCON (Flash Control Register). When read, this is the status register. When written, this is a command register. Note that the status bits are cleared to ’0’s when the command is written.

• FMDATA (Flash Data Register). Accepts data to be loaded into or from the flash element.

• FMADRL (Flash memory address low). Used to specify the flash element.

The flash elements that may be accessed and their addresses are shown in Table 14-1.

2003 Dec 8 92

Philips Semiconductors

User’s Manual - Preliminary -

FLASH PROGRAM MEMORY

Table 14-1: Flash elements accesable through IAP-Lite

Element Address Description

UCFG1 00h User Configuration byte 1.

Boot Vector 02h Boot vector

Status Bit 03h Status bit byte

Security

byte 0

Security

byte 1

Security

byte 2

Security

byte3

Mfgr Id 10h Signature byte, manufacturer id

Id_1 11h Signature byte,id 1 Id_2 12h Signature byte,id 2

ERASE-PROGRAMMING ADDITIONAL FLASH ELEMENTS

08h Security byte, sector 0

09h Security byte, sector 1

0Ah Security byte, sector 2

0Bh Security byte, sector 3

P89LPC906/907/908

The erase-program cycle takes 4ms to complete and is accomplished using the following steps:

• Write the address of the flash element to FMADRL.

• Write the CONF command (6CH) to FMCON.

• Write the data to be programmed to FMDATA.

• Read FMCON to check status. If aborted, repeat this sequence.

Writing the data to be programmed to FMDATA will start the erase-program process and place the CPU in a program-idle state. The CPU will remain in this idle state until the erase-program cycle is either completed or terminated by an interrupt. When the program-idle state is exited, FMCON will contain status information for the cycle.

If an interrupt occurs during an erase/programming cycle, the erase/programming cycle will be aborted and the OI flag (Operation Interrupted) in FMCON will be set. If the application permits interrupts during erasing-programming the user code should check the OI flag (FMCON.0) after each erase-programming operation to see if the operation was aborted. If the operation was aborted, the user’s code will need to repeat the process.

READING ADDITIONAL FLASH ELEMENTS

The read cycle is accomplished using the following steps:

• Write the address of the flash element to FMADRL.

• Write the CONF command (6CH) to FMCON.

• Read the data from FMDATA

The read cycle completes in a single machine cycle and thus will not enter an idle state. It can be interrupted. However, there is no need to check status.

An assembly language routine to perform an erase/program operation of a flash element is shown in Figure 14-4. A similar Clanguage routine is shown in Figure 14-5. A C-language routine to read a flash element is shown in Figure 14-6.

2003 Dec 8 93

Philips Semiconductors

User’s Manual - Preliminary -

FLASH PROGRAM MEMORY

;* Inputs: * ;* R5 = data to write(byte) * ;* R7 = element address(byte) * ;* Outputs: * ;* None *

CONF EQU 6CH

WR_ELEM: MOV FMADRL,R7 ;write the address MOV FMCON,#CONF ;load CONF command MOV FMDAT,R5 ;write the data

MOV R7,FMCON ;copy status for return MOV A,R7 ;read status ANL A,#0FH ;save only four lower bits JNZ BAD ;see if good or bad CLR C ;clear error flag if good RET ;and return BAD: SETB C ;set error flag if bad RET ;and return

Figure 14-4: Assembly language routine to erase/program a flash element

P89LPC906/907/908

unsigned char Fm_stat; // status result

bit PGM_EL (unsigned char, unsigned char); bit prog_fail;

void main ()

{ prog_fail=PGM_EL(0x02,0x1C); }

bit PGM_EL (unsigned char el_addr, unsigned char el_data) { #define CONF 0x6C // access flash elements

FMADRL = el_addr; //write element address to addr reg FMCON = CONF; //load command, clears page reg FMDATA = el_data; //write data and start the cycle Fm_stat = FMCON; //read the result status if ((Fm_stat & 0x0F)!=0) prog_fail=1; else prog_fail=0; return(prog_fail); }

Figure 14-5: C-language routine to erase/program a flash element

2003 Dec 8 94

Philips Semiconductors

User’s Manual - Preliminary -

FLASH PROGRAM MEMORY

#include <REG921.H>

unsigned char READ_EL (unsigned char); unsigned char GET_EL;

void main ()

{ GET_EL = READ_EL(0x02); }

unsigned char READ_EL (unsigned char el_addr) { #define CONF 0x6C // access flash elements unsigned char el_data; // local for element data FMADRL = el_addr; //write element address to addr reg FMCON = CONF; //access flash elements command el_data = FMDATA; /read the element data return(el_data); }

P89LPC906/907/908

Figure 14-6: C-language routine to read a flash element

2003 Dec 8 95

Philips Semiconductors

User’s Manual - Preliminary -

FLASH PROGRAM MEMORY

P89LPC906/907/908

USER CONFIGURATION BYTES

A number of user-configurable features of the P89LPC906/907/908 must be defined at power-up and therefore cannot be set by the program after start of execution. These features are configured through the use of Flash byte UCFG1 shown in Figure 14-7.

UCFG1

Address: xxxxh

Default: 63h

BIT SYMBOL FUNCTION

UCFG1.7 WDTE Watchdog timer reset enable. When set =1, enables the watchdog timer reset. When

cleared = 0, dusables the watchdog timer reset.The timer may still be used to generate an interrupt. Refer to Table 13-1 for details.

UCFG1.6 RPE Reset pin enable. When set =1, enables the reset function of pin P1.5. When cleared, P1.5

may be used as an input pin. NOTE: During a power-up sequence, the RPE selection is overriden and this pin will always functions as a reset input. After power-up the pin will function as defined by the RPE bit. Only a power-up reset will temporarily override the selection defined by RPE bit. Other sources of reset will not override the RPE bit.

UCFG1.5 BOE Brownout Detect Enable (see section "Brownout Detection" on page 53).

UCFG1.4 WDSE Watchdog Safety Enable bit. Refer to Table for details.

UCFG1.3 - Reserved (should remain unprogrammed at zero).

UCFG1.2-0 FOSC2-FSOC0 CPU oscillator type select. See section "Low Power Select (P89LPC906)" on page 28 for

additional information. Combinations other than those shown below should not be used. They are reserved for future use.When FOSC2:0 select either the internal RC or Watchdog oscillators, the crystal oscillator configuration is controlled by RTCCON. See Table and Table . Note: External clock input and crystal options are available on the

P89LPC906.

FOSC2-FOSC0

1 1 1 External clock input on XTAL1.

1 0 0 Watchdog Oscillator, 400KHz (+20/ -30% tolerance).

0 1 1 Internal RC oscillator, 7.373MHz ±2.5%.

0 1 0 Low frequency crystal, 20 kHz to 100 kHz.

0 0 1 Medium frequency crystal or resonator, 100 kHz to 4 MHz.

0 0 0 High frequency crystal or resonator, 4 MHz to 12 MHz.

Factory default value for UCFG1 is set for watchdog reset disabled, reset pin enabled, brownout detect enabled, and using the internal RC oscillator

Oscillator Configuration

76543210

WDTE RPE BOE WDSE - FOSC2 FOSC1 FOSC0

Figure 14-7: Flash User Configuration Byte 1 (UCFG1)

2003 Dec 8 96

Philips Semiconductors

User’s Manual - Preliminary -

FLASH PROGRAM MEMORY

P89LPC906/907/908

USER SECURITY BYTES

There are four User Sector Security Bytes (SEC0, ..., SEC3), each corresponding to one sector and having the following bit assignments:

SECx

Address: xxxxh

Unprogrammed value: 00h

BIT SYMBOL FUNCTION

SECx.7-3 - Reserved (should remain unprogrammed at zero).

SECx.2 EDISx Erase Disable x. Disables the ability to perform an erase of sector "x" in IAP mode. When

SECx.1 SPEDISx Sector Program Erase Disable x. Disables program or erase of all or part of sector x.

SECx.0 MOVCDISx MOVC Disable. Disables the MOVC command for sector x. Any MOVC that attempts to

76543210

-----

programmed, this bit and sector x can only be erased by a 'global' erase command using a commercial programmer . This bit and sector x CANNOT be erased in IAP mode.

This bit and sector x are erased by either a sector erase command (IAP or commercial programmer) or a 'global' erase command (commercial programmer).

read a byte in a MOVC protected sector will return invalid data. This bit can only be erased when sector x is erased.

EDISx SPEDISx MOVCDISx

Figure 14-8: User Sector Security Bytes (SEC0 ... SEC3)

Table 14-2: Effects of Security Bits

EDISx SPEDISx MOVCDISx Effects on Programming

0 0 0 None.

Security violation flag set for sector CRC calculation for the specific sector. Security

00 1

01 x

1x x

violation flag set for global CRC calculation if any MOVCDISx bit is set. Cycle aborted. Memory contents unchanged. CRC invalid. Program/erase commands will not result in a security violation.

Security violation flag set for program commands or an erase page command. Cycle aborted. Memory contents unchanged. Sector erase and global erase are allowed.

Security violation flag set for program or erase commands. Cycle aborted. Memory contents unchanged. Global erase is allowed.

2003 Dec 8 97

Philips Semiconductors

User’s Manual - Preliminary -

FLASH PROGRAM MEMORY

P89LPC906/907/908

Boot Vector

BOOTVEC

Address: xxxxh

Factory default value: 00h

BIT SYMBOL FUNCTION

BOOTVEC.7-5 - Reserved (should remain unprogrammed at zero).

BOOTVEC.4-0 - Boot Vector. If the Boot Vector is selected as the reset address, the P89LPC906/907/908

76543210

- - - BOOTV4 BOOTV3 BOOTV2 BOOTV1 BOOTV0

will start execution at an address comprised of 00H in the lower eight bits and this BOOTVEC as the upper bits after a reset. (See section "Power-On reset code execution" on page 71).

Figure 14-9: Boot Vector (BOOTVEC)

Boot Status

BOOTSTAT

Address: xxxxh

76543210

-------BSB

Factory default value: 00h

BIT SYMBOL FUNCTION

BOOTSTAT.7-1 - Reserved (should remain unprogrammed at zero).

BOOTSTAT.0 BSB Boot Status Bit. If programmed to ‘1’, the P89LPC906/907/908 will always start execution

at an address comprised of 00H in the lower eight bits and BOOTVEC as the upper bits after a reset. (See section "Power-On reset code execution" on page 71).

Figure 14-10: Boot Status (BOOTSTAT)

2003 Dec 8 98

Philips Semiconductors

User’s Manual - Preliminary -

INSTRUCTION SET

15. INSTRUCTION SET

Table 15-1: Instruction set summary

Mnemonic Description Bytes Cycles

ADD A,Rn Add register to A 1 1 28-2F

ADD A,dir Add direct byte to A 2 1 25

ADD A,@Ri Add indirect memory to A 1 1 26-27

ADD A,#data Add immediate to A 2 1 24

ADDC A,Rn Add register to A with carry 1 1 38-3F

ADDC A,dir Add direct byte to A with carry 2 1 35

ADDC A,@Ri Add indirect memory to A with carry 1 1 36-37

ADDC A,#data Add immediate to A with carry 2 1 34

SUBB A,Rn Subtract register from A with borrow 1 1 98-9F

SUBB A,dir Subtract direct byte from A with borrow 2 1 95

SUBB A,@Ri Subtract indirect memory from A with borrow 1 1 96-97

P89LPC906/907/908

Hex

code

ARITHMETIC

SUBB A,#data Subtract immediate from A with borrow 2 1 94

INC A Increment A 1 1 04

INC Rn Increment register 1 1 08-0F

INC dir Increment direct byte 2 1 05

INC @Ri Increment indirect memory 1 1 06-07

DEC A Decrement A 1 1 14

DEC Rn Decrement register 1 1 18-1F

DEC dir Decrement direct byte 2 1 15

DEC @Ri Decrement indirect memory 1 1 16-17

INC DPTR Increment data pointer 1 2 A3

MUL AB Multiply A by B 1 4 A4

DIV AB Divide A by B 1 4 84

DA A Decimal Adjust A 1 1 D4

LOGICAL

ANL A,Rn AND register to A 1 1 58-5F

ANL A,dir AND direct byte to A 2 1 55

ANL A,@Ri AND indirect memory to A 1 1 56-57

ANL A,#data AND immediate to A 2 1 54

2003 Dec 8 99

Philips Semiconductors

User’s Manual - Preliminary -

INSTRUCTION SET

Mnemonic Description Bytes Cycles

ANL dir,A AND A to direct byte 2 1 52

ANL dir,#data AND immediate to direct byte 3 2 53

ORL A,Rn OR register to A 1 1 48-4F

ORL A,dir OR direct byte to A 2 1 45

ORL A,@Ri OR indirect memory to A 1 1 46-47

ORL A,#data OR immediate to A 2 1 44

ORL dir,A OR A to direct byte 2 1 42

ORL dir,#data OR immediate to direct byte 3 2 43

XRL A,Rn Exclusive-OR register to A 1 1 68-6F

XRL A,dir Exclusive-OR direct byte to A 2 1 65

XRL A, @Ri Exclusive-OR indirect memory to A 1 1 66-67

XRL A,#data Exclusive-OR immediate to A 2 1 64

XRL dir,A Exclusive-OR A to direct byte 2 1 62

XRL dir,#data Exclusive-OR immediate to direct byte 3 2 63

CLR A Clear A 1 1 E4

CPL A Complement A 1 1 F4

P89LPC906/907/908

Hex

code

SWAP A Swap Nibbles of A 1 1 C4

RL A Rotate A left 1 1 23

RLC A Rotate A left through carry 1 1 33

RR A Rotate A right 1 1 03

RRC A Rotate A right through carry 1 1 13

DATA TRANSFER

MOV A,Rn Move register to A 1 1 E8-EF

MOV A,dir Move direct byte to A 2 1 E5

MOV A,@Ri Move indirect memory to A 1 1 E6-E7

MOV A,#data Move immediate to A 2 1 74

MOV Rn,A Move A to register 1 1 F8-FF

MOV Rn,dir Move direct byte to register 2 2 A8-AF

MOV Rn,#data Move immediate to register 2 1 78-7F

MOV dir,A Move A to direct byte 2 1 F5

MOV dir,Rn Move register to direct byte 2 2 88-8F

MOV dir,dir Move direct byte to direct byte 3 2 85

MOV dir,@Ri Move indirect memory to direct byte 2 2 86-87

2003 Dec 8 100

Philips P89LPC907, P89LPC906, P89LPC908 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

1. GENERAL DESCRIPTION

PIN CONFIGURATIONS

PRODUCT COMPARISON

PIN DESCRIPTIONS - P89LPC906

PIN DESCRIPTIONS - P89LPC907

PIN DESCRIPTIONS - P89LPC908

2. CLOCKS

ENHANCED CPU

CLOCK DEFINITIONS

CPU CLOCK (OSCCLK)

LOW SPEED OSCILLATOR OPTION - P89LPC906

MEDIUM SPEED OSCILLATOR OPTION - P89LPC906

HIGH SPEED OSCILLATOR OPTION - P89LPC906

OSCILLATOR OPTION SELECTION- P89LPC906

CLOCK OUTPUT - P89LPC906

ON-CHIP RC OSCILLATOR OPTION

WATCHDOG OSCILLATOR OPTION

EXTERNAL CLOCK INPUT OPTION - P89LPC906

CPU CLOCK (CCLK) WAKEUP DELAY

CPU CLOCK (CCLK) MODIFICATION: DIVM REGISTER

LOW POWER SELECT (P89LPC906)

3. INTERRUPTS

INTERRUPT PRIORITY STRUCTURE

EXTERNAL INTERRUPT INPUTS

EXTERNAL INTERRUPT PIN GLITCH SUPPRESSION

4. I/O PORTS

PORT CONFIGURATIONS

QUASI-BIDIRECTIONAL OUTPUT CONFIGURATION

OPEN DRAIN OUTPUT CONFIGURATION

INPUT-ONLY CONFIGURATION

PUSH-PULL OUTPUT CONFIGURATION

PORT 0 ANALOG FUNCTIONS

5. TIMERS 0 AND 1

MODE 0

MODE 2

MODE 3

MODE 6 - P89LPC907

TIMER OVERFLOW TOGGLE OUTPUT - P89LPC907

6. REAL-TIME CLOCK/SYSTEM TIMER

REAL-TIME CLOCK SOURCE

CHANGING RTCS1-0

REAL-TIME CLOCK INTERRUPT/WAKE UP

RESET SOURCES AFFECTING THE REAL-TIME CLOCK

7. POWER MONITORING FUNCTIONS

BROWNOUT DETECTION

POWER-ON DETECTION

POWER REDUCTION MODES

8. UART (P89LPC907, P89LPC908)

MODE 0

MODE 1

MODE 2

MODE 3

BAUD RATE GENERATOR AND SELECTION

UPDATING THE BRGR1 AND BRGR0 SFRS

FRAMING ERROR

BREAK DETECT

MORE ABOUT UART MODE 0

MORE ABOUT UART MODE 1

MORE ABOUT UART MODES 2 AND 3

FRAMING ERROR AND RI IN MODES 2 AND 3 WITH SM2 = 1

BREAK DETECT

DOUBLE BUFFERING

DOUBLE BUFFERING IN DIFFERENT MODES

TRANSMIT INTERRUPTS WITH DOUBLE BUFFERING ENABLED (MODES 1, 2 AND 3)

THE 9TH BIT (BIT 8) IN DOUBLE BUFFERING (MODES 1, 2 AND 3)

MULTIPROCESSOR COMMUNICATIONS

AUTOMATIC ADDRESS RECOGNITION

9. RESET

POWER-ON RESET CODE EXECUTION

10. ANALOG COMPARATORS

COMPARATOR CONFIGURATION

INTERNAL REFERENCE VOLTAGE

COMPARATOR INTERRUPT

COMPARATOR AND POWER REDUCTION MODES

COMPARATOR CONFIGURATION EXAMPLE

11. KEYPAD INTERRUPT (KBI)