Philips P87C528EFBB, P87C524EFLKA, P87C524EFFFA, P87C524EFAA, P87C524EBLKA Datasheet

...

 

87C524/87C528

80C51 8-bit microcontrollers

16K/32K, 512 OTP, I2C, watchdog timer

Product specification

Replaces data sheets 87C524 of 1998 May 01 and 87C528 of 1998 May 01

IC28 Data Handbook

1999 Jul 23

INTEGRATED CIRCUITS

Philips Semiconductors Product specification

87C524/87C528

80C51 8-bit microcontrollers 16K/32K, 512 OTP, I

C, watchdog timer

1999 Jul 23 853-1687 22041

DESCRIPTION

The 87C528 single-chip 8-bit microcontroller is manufactured in an advanced CMOS process and is a derivative of the 80C51 microcontroller family. The 87C528 has the same instruction set as the 80C51. Three versions of the derivative exist:

•83C528—32k bytes ROM

•83C524—16k bytes ROM

•80C528—ROMless version of the 83C528

•87C528—32k bytes EPROM

•83C524—16k bytes EPROM

This device provides architectural enhancements that make it applicable in a variety of applications in consumer, telecom and general control systems, especially in those systems which need large ROM and RAM capacity on-chip.

The 87C528 contains a 32k × 8 EPROM and the 87C524 contains a 16k x 8 EPROM. Both devices have a 512 × 8 RAM, four 8-bit I/O ports, two 16-bit timer/event counters (identical to the timers of the 80C51), a 16-bit timer (identical to the timer 2 of the 80C52), a watchdog timer with a separate oscillator, a multi-source, two-priority-level, nested interrupt structure, two serial interfaces (UART and I

C-bus), and on-chip oscillator and timing circuits.

In addition, the 87C524/87C528 has two software selectable modes of power reduction—idle mode and power-down mode. The idle mode freezes the CPU while allowing the RAM, timers, serial port, and interrupt system to continue functioning. The power-down mode saves the RAM contents but freezes the oscillator, causing all other chip functions to be inoperative.

FEA TURES

•80C51 instruction set

– 512 × 8 RAM – Memory addressing capability

64k ROM and 64k RAM

– Three 16-bit counter/timers – On-chip watchdog timer with oscillator – Full duplex UART – I

C serial interface

•Power control modes:

– Idle mode – Power-down mode – Warm start from power-down

•CMOS and TTL compatible

•Extended temperature ranges

•EPROM code protection

•OTP package available

•16 MHz speed at V

= 5 V

ORDERING INFORMATION

EPROM

TEMPERATURE oC RANGE

AND PACKAGE

FREQ (MHz)

Drawing Number

P87C528EBP N 0 to +70, Plastic Dual In-line Package 16 SOT129-1 P87C528EBA A 0 to +70, Plastic Leaded Chip Carrier 16 SOT187-2 P87C528EBB B 0 to +70, Plastic Quad Flat Pack 16 SOT307-2 P87C528EFP N –40 to +85, Plastic Dual In-line Package 16 SOT129-1 P87C528EFB B –40 to +85, Plastic Quad Flat Pack 16 SOT307-2 P87C524EBA A 0 to +70, Plastic Leaded Chip Carrier 16 SOT187-2 P87C524EBB B 0 to +70, Plastic Quad Flat Pack 16 SOT307-2

NOTE:

1. For ROM & ROMless devices, see data sheet P8X524/528.

Philips Semiconductors Product specification

87C524/87C528

80C51 8-bit microcontrollers 16K/32K, 512 OTP, I

C, watchdog timer

1999 Jul 23

BLOCK DIAGRAM

PROGRAMMABLE I/O

CPU

T0 T1

COUNTERS

XTAL2 XTAL1

INT0

INT1

CONTROL

SERIAL IN SERIAL OUT

OSCILLATOR

AND

TIMING

PROGRAM

MEMORY

(32K x 8

EPROM)

RAM AUX–RAM

DATA

MEMORY

(256 x 8)

TWO 16-BIT

TIMER/EVENT

COUNTERS

DATA

MEMORY

(256 x 8)

16-BIT TIMER/

EVENT COUNTER

WATCHDOG

TIMER

64K-BYTE BUS

EXPANSION

CONTROL

PROGRAMMABLE

SERIAL PORT

FULL DUPLEX UART

SYNCHRONOUS SHIFT

BIT-LEVEL

INTERFACE

FREQUENCY REFERENCE

T2 T2EX

RST

EXTERNAL

INTERRUPTS

PARALLEL PORTS,

ADDRESS/DATA BUS

AND I/O PINS

SHARED WITH

PORT 3

INTERNAL

INTERRUPTS

SDA SCL

SU00166

LOGIC SYMBOL

PORT 0

PORT 1PORT 2

PORT 3

ADDRESS AND

DATA BUS

ADDRESS BUS

T2 T2EX

RxD

TxD INT0 INT1

T0 T1

SECONDARY FUNCTIONS

RST

PSEN

ALE

XTAL1

XTAL2

SCL SDA

SU00165

Philips Semiconductors Product specification

87C524/87C528

80C51 8-bit microcontrollers 16K/32K, 512 OTP, I

C, watchdog timer

1999 Jul 23

PIN CONFIGURATIONS

1 2 3

4 5

6 7 8

9 10 11 12 13 14 15 16 17 18 19 20

T2/P1.0

T2EX/P1.1

P1.2

P1.3 P1.4

P1.5

SCL/P1.6

RST RxD/P3.0 TxD/P3.1

INT0

/P3.2

INT1

/P3.3 T0/P3.4 T1/P3.5

SDA/P1.7

/P3.6

/P3.7

XTAL2 XTAL1

P2.0/A8

P2.1/A9

P2.2/A10

P2.3/A11

P2.4/A12

P2.5/A13

P2.6/A14

P2.7/A15

PSEN

ALE

P0.7/AD7

P0.6/AD6

P0.5/AD5

P0.4/AD4

P0.3/AD3

P0.2/AD2

P0.1/AD1

P0.0/AD0

DUAL

IN-LINE

PACKAGE

SU00162

PLASTIC LEADED CHIP CARRIER PIN FUNCTIONS

LCC

6140

18 28

Pin Function

1 NC* 2 P1.0/T2 3 P1.1/T2EX 4 P1.2 5 P1.3 6 P1.4 7 P1.5 8 P1.6/SCL

9 P1.7/SDA 10 RST 11 P3.0/RxD 12 NC* 13 P3.1/TxD 14 P3.2/INT0 15 P3.3/INT1 16 P3.4/T0 17 P3.5/T1 18 P3.6/WR 19 P3.7/RD 20 XTAL2 21 XTAL1 22 V

Pin Function

23 NC* 24 P2.0/A8 25 P2.1/A9 26 P2.2/A10 27 P2.3/A11 28 P2.4/A12 29 P2.5/A13 30 P2.6/A14 31 P2.7/A15 32 PSEN 33 ALE 34 NC* 35 EA 36 P0.7/AD7 37 P0.6/AD6 38 P0.5/AD5 39 P0.4/AD4 40 P0.3/AD3 41 P0.2/AD2 42 P0.1/AD1 43 P0.0/AD0 44 V

SU00163A

* NO INTERNAL CONNECTIONS

Philips Semiconductors Product specification

87C524/87C528

80C51 8-bit microcontrollers 16K/32K, 512 OTP, I

C, watchdog timer

1999 Jul 23

PLASTIC QUAD FLAT PACK PIN FUNCTIONS

QFP

44 34

12 22

Pin Function

1 P1.5 2 P1.6/SCL 3 P1.7/SDA 4 RST 5 P3.0/RxD 6 NC* 7 P3.1/TxD 8 P3.2/INT0

9 P3.3/INT1 10 P3.4/T0 11 P3.5/T1 12 P3.6/WR 13 P3.7/RD 14 XTAL2 15 XTAL1 16 V

17 NC* 18 P2.0/A8 19 P2.1/A9 20 P2.2/A10 21 P2.3/A11 22 P2.4/A12

Pin Function

23 P2.5/A13 24 P2.6/A14 25 P2.7/A15 26 PSEN 27 ALE 28 NC* 29 EA 30 P0.7/AD7 31 P0.6/AD6 32 P0.5/AD5 33 P0.4/AD4 34 P0.3/AD3 35 P0.2/AD2 36 P0.1/AD1 37 P0.0/AD0 38 V

39 NC* 40 P1.0/T2 41 P1.1/T2EX 42 P1.2 43 P1.3 44 P1.4

SU00164

* NO INTERNAL CONNECTIONS

Philips Semiconductors Product specification

87C524/87C528

80C51 8-bit microcontrollers 16K/32K, 512 OTP, I

C, watchdog timer

1999 Jul 23

PIN DESCRIPTIONS

PIN NO.

MNEMONIC DIP LCC QFP TYPE NAME AND FUNCTION

20 22 16 I Ground: circuit ground potential.

40 44 38 I Power Supply: +5 V power supply pin during normal operation, Idle mode and

Power-down mode.

P0.0–0.7 39–32 43–36 37–30 I/O Port 0: Port 0 is an open-drain, bidirectional I/O port. Port 0 pins that have 1s written to

them float and can be used as high-impedance inputs. Port 0 is also the multiplexed low-order address and data bus during accesses to external program and data memory. In this application, it uses strong internal pull-ups when emitting 1s.

P1.0–P1.7 1–8 2–9 40–44

1–3

I/O Port 1: Port 1 is an 8-bit bidirectional I/O port with internal pull-ups, except P1.6 and P1.7

which have open drain. Port 1 pins that have 1s written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 1 pins that are externally pulled low will source current because of the internal pull-ups. (See DC Electrical Characteristics: I

). Port 1 can sink/source one TTL (4 LSTTL) inputs. Port 1 receives the low-order address byte during program memory verification. Port 1 also serves alternate functions for timer 2:

1 2 40 I T2 (P1.0): Timer/counter 2 external count input (following edge triggered). 2 3 41 I T2EX (P1.1): T imer/counter 2 trigger input. 7 8 2 I/O SCL (P1.6): I2C serial port clock line. 8 9 3 I/O SDA (P1.7): I2C serial port data line.

P2.0–P2.7 21–28 24–31 18–25 I/O Port 2: Port 2 is an 8-bit bidirectional I/O port with internal pull-ups. Port 2 pins that have

1s written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 2 pins that are externally being pulled low will source current because of the internal pull-ups. (See DC Electrical Characteristics: I

). Port 2 emits the high-order address byte during fetches from external program memory and during accesses to external data memory that use 16-bit addresses (MOVX @DPTR). In this application, it uses strong internal pull-ups when emitting 1s. During accesses to external data memory that use 8-bit addresses (MOV @Ri), port 2 emits the contents of the P2 special function register.

P3.0–P3.7 10–17 11,

13–19

7–13

I/O Port 3: Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. Port 3 pins that have

1s written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 3 pins that are externally being pulled low will source current because of the pull-ups. (See DC Electrical Characteristics: I

). Port 3 also serves the special features of

the SC80C51 family, as listed below:

10 11 5 I RxD (P3.0): Serial input port 11 13 7 O TxD (P3.1): Serial output port 12 14 8 I INT0 (P3.2): External interrupt 13 15 9 I INT1 (P3.3): External interrupt 14 16 10 I T0 (P3.4): Timer 0 external input 15 17 11 I T1 (P3.5): Timer 1 external input 16 18 12 O WR (P3.6): External data memory write strobe 17 19 13 O RD (P3.7): External data memory read strobe

RST 9 10 4 I/O Reset: A high on this pin for two machine cycles while the oscillator is running, resets the

device. An internal diffused resistor to V

permits a power-on reset using only an external

capacitor to V

. After a watchdog timer overflow, this pin is pulled high while the internal

reset signal is active.

ALE 30 33 27 I/O Address Latch Enable: Output pulse for latching the low byte of the address during an

access to external memory. In normal operation, ALE is emitted at a constant rate of 1/6 the oscillator frequency, and can be used for external timing or clocking. Note that one ALE pulse is skipped during each access to external data memory.

PSEN 29 32 26 O Program Store Enable: The read strobe to external program memory. When the device is

executing code from the external program memory, PSEN

is activated twice each machine

cycle, except that two PSEN

activations are skipped during each access to external data

memory. PSEN

is not activated during fetches from internal program memory.

EA 31 35 29 I External Access Enable: EA must be externally held low during RESET to enable the

device to fetch code from external program memory locations 0000H to 7FFFH. If EA

is held high during RESET, the device executes from internal program memory unless the program counter contains an address greater than 7FFFH. EA

is don’t care after RESET.

XTAL1 19 21 15 I Crystal 1: Input to the inverting oscillator amplifier and input to the internal clock generator

circuits.

XTAL2 18 20 14 O Crystal 2: Output from the inverting oscillator amplifier .

Philips Semiconductors Product specification

87C524/87C528

80C51 8-bit microcontrollers 16K/32K, 512 OTP, I

C, watchdog timer

1999 Jul 23

Table 1. 8XC524/8XC528 Special Function Registers

SYMBOL DESCRIPTION

DIRECT

ADDRESS

BIT ADDRESS, SYMBOL, OR ALTERNATIVE PORT FUNCTION MSB LSB

RESET VALUE

ACC* Accumulator E0H E7 E6 E5 E4 E3 E2 E1 E0 00H B* B register F0H F7 F6 F5 F4 F3 F2 F1 F0 00H DPTR:

DPH DPL

Data pointer (2 bytes):

Data pointer high Data pointer low

83H 82H

00H 00H

AF AE AD AC AB AA A9 A8

IE*# Interrupt enable A8H EA ES1 ET2 ES0 ET1 EX1 ET0 EX0 00H

BF BE BD BC BB BA B9 B8

IP*# Interrupt priority B8H – PS1 PT2 PS0 PT1 PX1 PT0 PX0 x0000000B

87 86 85 84 83 82 81 80

P0* Port 0 80H AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 FFH

97 96 95 94 93 92 91 90

P1* Port 1 90H SDA SEL – – – – T2EX T2 FFH

A7 A6 A5 A4 A3 A2 A1 A0

P2* Port 2 A0H A15 A14 A13 A12 A11 A10 A9 A8 FFH

B7 B6 B5 B4 B3 B2 B1 B0 P3* Port 3 B0H RD WR T1 T0 INT1 INT0 TxD RxD FFH PCON Power control 87H SMOD – – – GF1 GF0 PD IDL 0xxx0000B

D7 D6 D5 D4 D3 D2 D1 D0 PSW* Program status word D0H CY AC F0 RS1 RS0 OV F1 P 00H RCAP2H#

RCAP2L# SBUF

Capture high Capture low Serial data buffer

CBH CAH 99H

00H 00H xxxxxxxxB

9F 9E 9D 9C 9B 9A 99 98 SCON* Serial controller 98H SM0 SM1 SM2 REN TB8 RB8 TI RI 00H S1BIT# Serial I2C data D9H/RD SDI 0 0 0 0 0 0 0 x0000000B

WR SD0 X X X X X X X 0xxxxxxxB

S1INT# Serial I2C interrupt DAH INT X X X X X X X 0xxxxxxxB

DF DE DD DC DB DA D9 D8

S1SCS*# Serial I2C control D8H/RD SDI SCI CLH BB RBF WBF STR ENS xxxx0000B

WR SD0 SC0 CLH X X X STR ENS 00xxxx00B

SP Stack pointer 81H 07H

8F 8E 8D 8C 8B 8A 89 88 TCON* Timer control 88H TF1 TR1 TF0 TR0 IE1 IT1 IE0 IT0 00H

CF CE CD CC CB CA C9 C8

T2CON*# Timer 2 control C8H TF2 EXF2 RCLK TCLK EXEN2 TR2 C/T2

CP/RL2

00H

TH0 TH1 TH2# TL0 TL1 TL2# T3#

Timer high 0 Timer high 1 Timer high 2 Timer low 0 Timer low 1 Timer low 2 Watchdog timer

8CH 8DH

CDH

8AH 8BH

CCH

FFH

00H 00H 00H 00H 00H 00H

00H TMOD Timer mode 89H GATE C/T M1 M0 GATE C/T M1 M0 00H WDCON# Watchdog control A5H A5H

* SFRs are bit addressable. # SFRs are modified from or added to the 80C51 SFRs.

Philips Semiconductors Product specification

87C524/87C528

80C51 8-bit microcontrollers 16K/32K, 512 OTP, I

C, watchdog timer

1999 Jul 23

Table 2. Internal and External Program Memory Access with Security Bit Set

INSTRUCTION

ACCESS TO INTERNAL

PROGRAM MEMORY

ACCESS TO EXTERNAL

PROGRAM MEMORY

MOVC in internal program memory YES YES MOVC in external program memory NO YES

INTERNAL DATA MEMORY

The internal data memory is divided into three physically separated segments: 256 bytes of RAM, 256 bytes of AUX-RAM, and a 128 bytes special function area. These can be addressed each in a different way . – RAM 0 to 127 can be addressed directly and indirectly as in the

80C51. Address pointers are R0 and R1 of the selected register bank.

– RAM 128 to 255 can only be addressed indirectly as in the 80C51.

Address pointers are R0 and R1 of the selected register bank.

– AUX-RAM 0 to 255 is indirectly addressed in the same way as

external data memory with the MOVX instructions. Address pointers are R0, R1 of the selected register bank and DPTR. An access to AUX-RAM 0 to 255 will not affect ports P0, P2, P3.6 and P3.7.

An access to external data memory locations higher than 255 will be performed with the MOVX DPTR instructions in the same way as in the 8051 structure, so with P0 and P2 as data/address bus and P3.6 and P3.7 as write and read timing signals. Note that these external data memory cannot be accessed with R0 and R1 as address pointer.

TIMER 2

Timer 2 is functionally equal to the Timer 2 of the 8052AH. Timer 2 is a 16-bit timer/counter. These 16 bits are formed by two special function registers TL2 and TH2. Another pair of special function register RCAP2L and RCAP2H form a 16-bit capture register or a 16-bit reload register. Like Timer 0 and 1, it can operate either as a timer or as an event counter. This is selected by bit C/T2N in the special function register T2CON. It has three operating modes: capture, autoload, and baud rate generator mode which are selected by bits in T2CON.

WATCHDOG TIMER T3

The watchdog timer consists of an 11-bit prescaler and an 8-bit timer formed by special function register T3. The prescaler is incremented by an on-chip oscillator with a fixed frequency of 1MHz. The maximum tolerance on this frequency is –50% and +100%. The 8-bit timer increments every 2048 cycles of the on-chip oscillator. When a timer overflow occurs, the microcontroller is reset and a reset output pulse of 16 × 2048 cycles of the on-chip oscillator is generated at pin RST. The internal RESET signal is not inhibited when the external RST pin is kept low by, for example, an external reset circuit. The RESET signal drives port 1, 2, 3 into the high state and port 0 into the high impedance state.

The watchdog timer is controlled by one special function register WDCON with the direct address location A5H. WDCON can be read and written by software. A value of A5H in WDCON halts the on-chip oscillator and clears both the prescaler and timer T3. After the RESET signal, WDCON contains A5H. Every value other than A5H in WDCON enables the watchdog timer. When the watchdog timer is enabled, it runs independently of the XTAL-clock.

Timer T3 can be read on the fly. Timer T3 can only be written if WDCON contains the value 5AH. A successful write operation to T3 will clear the prescaler and WDCON, leaving the watchdog enabled and preventing inadvertent changes of T3. To prevent an overflow of

the watchdog timer, the user program has to reload the watchdog timer within periods that are shorter than the programmed watchdog timer internal. This time interval is determined by an 8-bit value that has to be loaded in register T3 while at the same time the prescaler is cleared by hardware.

Watchdog timer interval =

[256 * (T3)] 2048

on * chip oscillator frequency

BIT-LEVEL I2C INTERFACE

This bit-level serial I/O interface supports the I2C-bus. P1.6/SCL and P1.7/SDA are the serial I/O pins. These two pins meet the I

C specification concerning the input levels and output drive capability. Consequently , these pins have an open drain output configuration. All the four modes of the I

C-bus are supported:

– master transmitter – master receiver – slave transmitter – slave receiver

The advantages of the bit-level I

C hardware compared with a full

software I

C implementation are:

– the hardware can generate the SCL pulse – Testing a single bit (RBF respectively, WBF) is sufficient as a

check for error free transmission.

The bit-level I

C hardware operates on serial bit level and performs the following functions: – filtering the incoming serial data and clock signals

– recognizing the START condition – generating a serial interrupt request SI after reception of a START

condition and the first falling edge of the serial clock – recognizing the STOP condition – recognizing a serial clock pulse on the SCL line – latching a serial bit on the SDA line (SDI) – stretching the SCL LOW period of the serial clock to suspend the

transfer of the next serial data bit – setting Read Bit Finished (RBF) when the SCL clock pulse has

finished and Write Bit Finished (WBF) if there is no arbitration loss

detected (i.e., SDA = 0 while SDO = 1) – setting a serial clock Low-to-High detected (CLH) flag – setting a Bus Busy (BB) flag on a START condition and clearing

this flag on a STOP condition – releasing the SCL line and clearing the CLH, RBF and WBF flags

to resume transfer of the next serial data bit – generating an automatic clock if the single bit data register S1BIT

is used in master mode. The following functions must be done in software:

– handling the I

C START interrupts – converting serial to parallel data when receiving – converting parallel to serial data when transmitting – comparing the received slave address with its own – interpreting the acknowledge information – guarding the I

C status if RBF or WBF = 0.

+ 18 hidden pages