Philips MHC-08100B, MHC-08100A, MHC-08100 User Manual

Lamp Material Data Sheet (LMDS)

Philips Lighting Company

Product: Philips Medium Wattage Metal Halide ELITE Lamps

Section 1. Manufacturer and Contact Information

CDM-T Type Lamps – All wattages

Philips Lighting Company Division of Philips Electronics North America Corporation

P.O. Box 6800
Somerset, NJ 08875-6800

200 Franklin Square Drive

24 HR Emergency Phone Number: [phone] CHEMTREC
Other Information Calls: [phone] Philips Lighting Technical Information

LMDS #: MHC-08100B

Date:

10/20/2008

Page 1 of 2

Section 2. Hazardous Ingredients/Identity Information

These lamps contain the following materials: Exposure Limits

Material (CAS #) OSHA PEL ACGIH TLV PERCENTAGE
(mg/m

Mercury (7439-97-6) 0.1 0.025 <0.03%
Mercury Iodide (7774-29-0) 0.01 0.025 <0.001%
Thallium Iodide (7790-30-9) 0.1 0.1 <0.02%
Manganese Iodide (7790-33-2) 5.0 0.2 <0.001%
Calcium Iodide (10102-68-8) 5.0 <0.25%
Sodium Iodide (7681-82-5) <0.06%
Cerium Iodide (7790-87-6) <0.01%
Krypton (Kr

85

(1)

)

(13983-27-2) <25ηCi

3) (

mg/m3)

(by weight)

(1)

This material is fully contained in the inner arc tube and aids lamp starting.

Section 3. Physical Properties

Not applicable to an intact lamp. The outer bulb is UV-block quartz glass, the base is ceramic with stainless steel pins,
and the inner envelope (arc tube) is ceramic. Other chemical or physical characteristics are not applicable.

Section 4. Fire and Explosion Hazards

The outer glass bulb encloses a ceramic arc tube which is refractory. There is a vacuum within the outer envelope. If
the lamp is dropped or struck, a possible implosion could result which would cause flying glass.

WARNING: The arc tubes of metal halide lamps are designed to operate at high pressures and temperatures (up to
900°C). If the arc tube ruptures for any reason, the outer bulb may break and shards of extremely hot glass may be
discharged into the surrounding environment, with the associated risk of property damage or personal injury.

200 Franklin Square Drive
P.O. Box 6800
Somerset, NJ 08875-6800

Tel: [phone]

Philips Electronics North American Corporation

A Division of

Section 5. Reactivity

Incompatibility: If using a lamp support, ensure it is electrically isolated to avoid possible decomposition of the bulb glass.

Section 6. Health Hazards

Other than exposure to high operating temperatures, there are no health hazards associated with an intact lamp.

WARNING: These lamps can cause serious skin burns and eye inflammation from short wave ultraviolet radiation if the
outer envelope of the lamp is broken or punctured. Do not use where people will remain for more than a few minutes
when the envelope is broken unless adequate shielding or other safety precautions are used. Certain lamps that will
automatically extinguish when the outer envelope is broken are available commercially.

The inner envelope is composed of a ceramic material containing elemental mercury and small amounts of thallium and
other iodides. In the event the inner envelope is broken, avoid inhalation of any vapors or skin contact with any of the
fragments or contents.

Thallium is a cumulative poison. It, or its salts, can be absorbed through the skin. If they are ingested, they can be
absorbed by the gastrointestinal tract. Seek competent medical help for all exposures. Although the amount of thallium
in the inner envelope is small, avoid breaking the lamps. If lamps are broken, use adequate personal protection and
ventilation.

Section 7. Lamp Disposal Procedures

Normal precautions should be taken for the collection of glass particles in the event a lamp is broken.

Waste Disposal Method: These lamps contain some amount of mercury. When a lamp is to be disposed, it is subject to
the current EPA Toxicity Characteristic Leaching Procedure (TCLP) disposal criteria. This test is used to determine if an
item can be managed as hazardous or non-hazardous waste. These lamps are not TCLP compliant and should be
managed as a hazardous waste under the EPA Universal Waste Rules.

All disposal options should be evaluated with respect to federal, state, and local requirements. Before disposing of waste
lamps, check with federal, state, and/or local officials for current guidelines and regulations. Philips encourages recycling
of its products through qualified recycling facilities.

Section 8. Control Measures

Respiratory Protection: None while operating. NIOSH-approved respirator should be used if large quantities of lamps
are being broken for disposal.
Ventilation: Avoid inhalation of any airborne dust. Provide local exhaust when disposing of large quantities of lamps.
Hand and Eye Protection: Appropriate hand and eye protection should be worn when disposing of lamps and/or handling
broken glass.

Section 9. Regulatory Information

As a product, these mercury-containing lamps, when shipped in the manufacturer’s original packaging, are not regulated
by air, truck, or ocean shipment. As a waste, these lamps may be regulated in various states and local communities.
This safety data sheet does not constitute “knowledge of the waste” in certain jurisdictions.

This document supercedes previous document: MHC-08100A Dated 09/02/2008
MHC-08100 dated 06/08/2008.

Occupational Health and Safety Administration (OSHA) Material Safety Data Sheet (MSDS) requirements for materials

are not applicable to manufactured articles in which individuals would not be subjected to materials contained in the article

during its normally intended use. The information in this document is provided as a courtesy and is intended to provide
relevant information in the event the articles it covers are encountered during unintended, or abnormal, circumstances.