Philips MCM279 12 Quick Start Guide

Page 1
Quick Start Guide
Prepare
Install
Step A
Step
Step
B
C
CR2025
2
User Manual
1
Quick Start Guide
MCM279
What’s in the Box?
You should find these items upon opening the box.
Stand FM wire antenna
Power adaptor
User manual
MW antenna
Quick start guide
Remote control with
1 x CR2025 battery
Page 2
Install
Mounting the stand onto the set
1
Locate the bottom of the main unit and find the slot, then slide the stand in the slot until it stops, as indicated in the figure.
Rear connections
1
Connect the cable of the left speaker to LEFT (red and black) and the cable of the right speaker to RIGHT (red and black).
2
Extend the wire antenna and fit it to FM ANTENNA.
3
Insert the MW antenna to MW ANTENNA jacks.
4
Connect the power adaptor to the wall socket.
Tip
– To receive optimal radio reception, put the main unit and the antennas as far away as possible from the power adaptor.
Page 3
SetupSetup
Setting the clock
Enjoy
1
Press and hold STANDBY-ON/ ECO POWER y to switch the set to Standby mode.
The display shows the set time.-- --:-- -- displays by default if you have not set the clock.
2
In the standby mode, press and hold DISPLAY/CLOCK (or CLOCK on the remote control).
The hours digits start flashing.
IMPORTANT!
– Remove the protective plastic tab before using the remote control.
3
To switch between 12 hour and 24 hour display, press PROGRAM (or PROG on the remote control) repeatedly to set the hours.
4
Hold down or press VOLUME +/- repeatedly to set the hours.
5
Press DISPLAY/CLOCK (or CLOCK on the remote control) to confirm.
6
Hold down or press VOLUME +/- repeatedly to set the minutes.
7
Press DISPLAY/CLOCK (or CLOCK on the remote control) to confirm.
Notes for remote control:
– First, select the source you wish to control by pressing one of the source select keys on the remote control (CD or TUNER, for example). –Then select the desired function ( 2;, 4, example).
¢
for
Playing discs
With this system, you can play all pre-recorded audio CDs (CDDA), all finalized audio CD-Rs
and CD-RWs, MP3/WMA-CDs (CD-Rs/CD-RWs with MP3/WMA files)
1
Press SOURCE (or CD on the remote control) once or more to select CD.
2
Press OPEN/CLOSE ç to open the CD compartment.
3
Insert a disc with the printed side facing outward. Then close the CD door.
4
Press ÉÅ to start playback.
5
To stop playback, press STOPÇ.
Page 4
Tuning to radio stations
Enjoy
1
Press SOURCE (or TUNER on the remote control) once or more to select TUNER.
2
Press and hold PROGRAM (or PROG on the remote control) until AUTO appears.
Available stations (RDS, FM and MW) are programmed.
3
Press ALBUM/PRESET +/- (or 3/4 on the remote control) buttons once or more until the desired preset station is displayed.
Playing a USB mass storage device
With the Hi-Fi system, you can use USB flash memory (USB 2.0 or USB1.1),
USB flash players (USB 2.0 or USB1.1), memory cards (requires an additional card reader to work with this Hi-Fi system).
1
Insert the USB device’s USB plug into the socket on the front panel of the main set.
2
Press SOURCE (or USB on the remote control) once or more to select USB.
3
Play the USB’s audio files as you do with the albums/tracks on a CD.
Detailed playback features and additional functions are described in the accompanied owner's manual.
C Royal Philips Electronics N.V. 2008
All rights reserved.
http://www.philips.com
PDCC-JH/ZYL-0820
Loading...