Philips MCM-167 Service Manual

Micro Hi-Fi System

�

MCM167

-/12

CONTENTS

Technical specification ..................................................................1-2

Version variation............................................................................1-2

Service measurement setup..........................................................1-3

Service aids .................................................................................1-4

Instructions on CD playability ...............................................2-1.. 2-2

Disassembly diagram............ ........................................................3-1

Block diagram ................................................................................4-1

Wiring diagram ..............................................................................5-1

Main board

Circuit diagram ..................................................................6-1..6-3

Layout diagram ..................................................................6-4..6-5

Display board

Circuit diagram .........................................................................7-1

Layout diagram ..................................................................7-2..7-3

Cassette board

Circuit diagram .........................................................................8-1

Layout diagram .........................................................................8-2

Exploded view diagram .................................................................9-1

Mechanical parts list ......................................................................9-2

Electrical parts list...............................................................10-1..10-2

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips.

Published by LX 0910 Service Audio Subject to modification

Version 1.0

3141 785 33590

Ampliﬁer

Rated Output Power 2X5W RMS

Frequency Response 60 - 16kHz,±3dB

Signal to Noise Ratio >65dB

Aux Input 0.5V RMS 20kohm

Disc

Laser Type Semiconductor

Disc Diameter 12cm/8cm

Support Disc CD-DA, CD-R, CD-RW,

MP3-CD, WMA-CD

Audio DAC 24Bits / 44.1kHz

Total Harmonic Distortion <1%

Frequency Response 60Hz -16kHz (44.1kHz)

S/N Ratio >65dBA

Tuner

TuningRange FM:87.5- 108MHz;

MW: 531 - 1602kHz

Tuninggrid 50KHz

Sensitivity

-Mono, 26dB S/N Ratio

-Stereo,46dB S/N Ratio

<22 dBf >43 dBf

SearchSelectivity >28dBf

TotalHarmonic Distortion <3%

SignaltoNoise Ratio >55dB

Tape deck

Frequency response

-Normal tape(typeI) 125 - 8000 Hz (8dB)

Signal-to-noiseratio

-Normal tape(typeI) 40 dBA

Wow and ?utter <0.4% JIS

Speakers

SpeakerImpedance 4ohm

SpeakerDriver 3.5”woofer+0.8”tweeter

Sensitivity >82dB/m/W

General information-Specs

AC power 220 -230V,50Hz

OperationPower Consumption 20W

StandbyPower Consumption <4W

Eco StandbyPower Consumption <2W

Dimensions

-Main Unit(W x H x D)

-SpeakerBox (W x H x D)

209 x231 x 147mm 146 x 228 x 160mm

Weight

-With Packing

-Main Unit

-SpeakerBox

6.6kg

1.95kg 2 x 1.2kg

TECHNICAL SPECIFICATION

Type /Versions:

Features

Board in used:

MCM167

Service policy

DISPLAY BOARD

* TIPS : C -- Component Lever Repair.

M -- Module Lever Repair

√ -- Used

/05 /12

/55

89/16/85/

Feature diffrence

RDS & DAB VOLTAGE SELECTOR ECO STANDBY - DARK

√

Type /Versions:

/05 /12

/55

89/16/85/

VERSION VARIATION

39/

MAIN BOARD

CASSETTE BOARD

MCM167

1 - 2

MEASUREMENT SETUP

Tuner FM

1-3

Bandpass

LF Voltmeter

e.g. PM2534

RF Generator

e.g. PM5326

DUT

250Hz-15kHz

e.g. 7122 707 48001

Ri=50:

S/N and distortion meter

e.g. Sound Technology ST1700B

Use a bandpass filter to eliminate hum (50Hz, 100Hz) and disturbance from the pilottone (19kHz, 38kHz).

Tuner AM (MW,LW)

RF Generator

e.g. PM5326

Ri=50:

DUT

Frame aerial

e.g. 7122 707 89001

Bandpass

250Hz-15kHz

e.g. 7122 707 48001

LF Voltmeter

e.g. PM2534

S/N and distortion meter

e.g. Sound Technology ST1700B

To avoid atmospheric interference all AM-measurements have to be carried out in a Faraday´s cage. Use a bandpass filter (or at least a high pass filter with 250Hz) to eliminate hum (50Hz, 100Hz).

Use Audio Signal Disc (replaces test disc 3)

DUT

SBC429 4822 397 30184

S/N and distortion meter

e.g. Sound Technology ST1700B

LEVEL METER

e.g. Sennheiser UPM550

Recorder

Use Universal Test Cassette CrO2 SBC419 4822 397 30069

or Universal Test Cassette

LF Generator

e.g. PM5110

Fe SBC420 4822 397 30071

DUT

S/N and distortion met

e.g. Sound Technology ST170

LEVEL METER

e.g. Sennheiser UPM550

with FF-filter

SERVICE AIDS

1-4

All ICs and many other semi-conductors are susceptible to electrostatic discharges (ESD). Careless handling during repair can reduce life drastically. When repairing, make sure that you are connected with the same potential as the mass of the set via a wrist wrap with resistance. Keep components and tools also at this potential.

WARNING

Safety regulations require that the set be restored to its original condition and that parts which are identical with those specified, be used

Safety components are marked by the symbol

ESD

CLASS 1

LASER PRODUCT

Lead free

INSTRUCTIONS ON CD PLAYABILITY

Customer complaint

"CD related problem"

Set remains closed!

check playability

2 - 1

playability

ok ?

Play a CD

for at least 10 minutes

check playability

playability

ok ?

"fast" lens cleaning

check playability

playability

ok ?

For flap loaders (= access to CD drive possible) cleaning method

4 is recommended

add Info for customer

"SET OK"

return set

1 - 4 For description - see following pages

Exchange CDM

INSTRUCTIONS ON CD PLAYABILITY

2 - 2

PLAYABILITY CHECK

For sets which are compatible with CD-RW discs

use CD-RW Printed Audio Disc ....................7104 099 96611

TR 3 (Fingerprint) TR 8 (600µ Black dot) maximum at 01:00

• playback of these two tracks without audible disturbance playing time for: Fingerprint

Black dot from 00:50 to 01:10

• jump forward/backward (search) within a reasonable time

For all other sets

use CD-DA SBC 444A..................................4822 397 30245

TR 14 (600µ Black dot) maximum at 01:15 TR 19 (Fingerprint) TR 10 (1000µ wedge)

• playback of all these tracks without audible disturbance playing time for: 1000µ wedge 10seconds

Fingerprint 10seconds Black dot from 01:05 to 01:25

• jump forward/backward (search) within a reasonable time

10seconds

LIQUID LENS CLEANING

Before touching the lens it is advised to clean the surface of the lens by blowing clean air over it. This to avoid that little particles make scratches on the lens.

Because the material of the lens is synthetic and coated with a special anti-reflectivity layer, cleaning must be done with a non-aggressive cleaning fluid. It is advised to use “Cleaning Solvent

The actuator is a very precise mechanical component and may not be damaged in order to guarantee its full function. Clean the lens gently (don’t press too hard) with a soft and clean cotton bud moistened with the special lens cleaner.

The direction of cleaning must be in the way as indicated in the picture below.

CUSTOMER INFORMATION

It is proposed to add an addendum sheet to the set which informs the customer that the set has been checked carefully - but no fault was found. The problem was obviously caused by a scratched, dirty or copy-protected CD. In case problems remain, the customer is requested to contact the workshop directly. The lens cleaning (method 3) should be mentioned in the addendum sheet.

The final wording in national language as well as the printing is under responsibility of the Regional Service Organizations.

DISASSEMBLY DIAGRAM VIEW

3 - 1

DISPLAY PCB

MAIN PCB

CASS DECK PCB

SET BLOCK DIAGRAM

4 - 1 4 - 1

+ 16 hidden pages