Philips MCD802-12 User Manual
Welcome to Philips!
Micro DVD Theater
Register your product and get support at
www.philips.com/welcome
Quick start guide
1
Connect
Setup
2
Enjoy
3
MCD802
What’s in the box
Control cableRemote control
Quick start guide
1
Connect
Setup
2
Enjoy
2
Quick start guide User manual
Open the battery compartment.
1
Insert 2 AAA batteries with correct
2
polarity (+/-) as indicated.
Close the battery compartment.
3
Connect the supplied control cable to the
1
CONTROL CABLE jacks on the main unit.
Power cord
1
A
B
Composite video
cable (yellow)
FM wire antenna
Connect
Install remote control batteries
Connect control cable
XXXXXXX
1
C
XXXXXX
Eng
XXXXXX
D
E
Connect
Connect speakers
Connect FM antenna
Connect TV
1
Note
D
• Ensure that the colors of the speaker
Left speakerRight speaker
TV
wires and terminals are matched.
Hold down the socket fl ap.
1
Insert the stripped part of the wire com-
2
pletely.
Insert the right speaker wires to •
“ SPEAKER RIGHT ”, left speaker wires
to “ SPEAKER LEFT ”.
Release the socket fl ap.
3
Connect the supplied FM wire antenna to
1
the FM ANTENNA socket on the unit.
Connect the supplied composite video
1
cable to:
• the VIDEO socket on this unit.
• the video input socket on the TV.
F
C
• Risk of product damage! Ensure that the
• Risk of electric shock! When you unplug
• Before connecting the AC power cord,
Connect
Connect power
Caution
power supply voltage corresponds to
the voltage printed on the back or the
underside of the unit.
the AC power cord, always pull the plug
from the socket. Never pull the cord.
ensure you have completed all other
connections.
Connect the power cord to the AC
1
MAINS~ jack on the main unit.
Connect the power plug to the wall outlet.
2
Tip
E
• See the User Manual for how to connect
other devices to this system.
2
A
In standby mode, press CLOCK to activate
1
the clock setting mode.
The time digits are displayed and begin to blink.
»
If the time digits are not displayed, press
»
and hold for more than 2 seconds to
switch to standby mode, then repeat step 1.
Press / to set the hour.
2
Press / to set the minute.
3
Press and hold CLOCK to select 12-hour
4
or 24-hour format.
P ress CLOCK to confi rm .
5
3
A
Press DISC to select the disc source.
1
2 Press to open the disc compartment.
3 Insert a disc with the printed side facing
up, then close the disc compartment.
Play starts automatically.
»
To pause/resume play, press • .
To stop play, press •
B
Setup
Set the clock
Enjoy
Play disc
9
Play from USB
3
C
E
• For optimal reception, fully extend and adjust
the position of the FM antenna.
First time tuning
When you access to radio mode for the fi rst
time, follow the instructions to install the radio
stations.
Press TUNER .
1
‘ AUTO INSTALL ... PRESS PLAY’ is displayed.
»
Press .
2
All detected radio stations are stored.
»
Once complete, it tunes to the fi rst preset
»
radio station.
• To stop auto tuning, press 9 .
Reinstall and listen to radio stations
Press TUNER to select the tuner source.
1
Press and hold PROG for more than 2 sec-
s
i
l
d
e
e
b
a
L
.
2
onds to activate automatic program mode.
All available stations are programmed in the
»
order of waveband reception strength.
Press J/ K to select a preset number.
3
Enjoy
Program and tune to radio
stations
Tip
Tip
E
• Detailed features and additional functions are
described in the user manual.
EN
Flip open the USB socket cover on the
1
front panel.
Insert the USB plug of a USB device into
2
the USB socket.
Press USB to select the USB source.
3
Play starts automatically.
»
To pause/resume play, press • .
To stop play, press •
9
.
© Royal Philips Electronics N.V. 2009
All rights reserved.
Specifi cations are subject to change without notice.
Trademarks are the proper ty of Koninklijke Philips
Electronics N.V. or their respective owners.
Printed in China
MCD802_12_QSG_V2.0
Loading...