Philips LTC 0435, LTC 0455 installation Guide

Philips
Communication,
Security & Imaging

www.philipscsi.com

INSTALLATION

INSTRUCTIONS

EN

FR

DE

ES

NL

IT

PT

ZH

LTC 0435 & LTC 0455

SERIES COLOR CAMERAS

Genion_ii_00111.qxd 7/4/02 11:39 AM Page 1

The lighting flash with arrowhead sysbol,
within an equilateral triangle, is intended
to alert the user to the presence of
uninsulated "dangerous voltage" within the
product's enclosure that may be of
sufficient magnitude to constitute a risk to
persons.
The exclamation point, within an
equilateral triangle, is intended to alert the
user to the presence of important operating
and maintenance accompanying the
appliance.

1. Read these instructions

2. Keep these instructions.

3. Heed all Warnings.

4. Follow all instructions.

5. Do not use the apparatus near water.

6. Clean with a dry cloth only.

7. Do not install near heat sources such as
radiators, heat registers, stoves, or other
apparatus that generates heat (including
amplifiers).

8. Do not defeat the purpose of a polarized or
grounded mains plug. A polarized plug has
dissimilar prongs (one wider than the other) to
ensure correct polarity, while a grounded plug
has an additional 'ground' prong provided for
your safety. If the plug supplied with the
apparatus does not fit into your outlet, consult
an electrician for advice.

9. Protect the power-supply cord from being
walked on or pinched, particularly close to
plugs, receptacles and the point where it exits
from the apparatus.

10. Only use attachments and accessories
(including stands, tripods, mounting brackets
and housings) specified or recommended by the
manufacturer.

11. Unplug the apparatus during lightning storms
and when unused for extended periods.

12. Do not attempt to service this unit yourself as
opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.

13. Servicing is required when the apparatus does
not function in the normal way, has been
dropped, if liquid has been spilled on it, or if it
has been exposed to rain or water. Unplug the
unit from the outlet and refer servicing to
qualified service personnel.

14. An all-pole mains switch with contact
separation of at least 3 mm in each pole shall be
incorporated in the electrical installation of the
building.

Warning

To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture.

FCC Information

Caution: Any changes or modifications to
construction of this device that are not expressly
approved by the party responsible for compliance
could void the user’s authority to operate the
equipment.

This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try
to correct the interference by one or more of the
following measures:

• Re-orient or relocate the receiving antenna.

• Increase the separation between the equipment
and receiver.

• Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.

• Consult the dealer or an experienced radio/TV
technician for help.

IMPORTANT SAFETY INSTRUCTIONS

Genion_ii_00111.qxd 7/4/02 11:39 AM Page 2

SPECIFICATIONS

LTC 0435/x0 LTC 0455/x0

Standard resolution High resolution
Standard PAL NTSC PAL NTSC
Active pixels (H x V) 512 x 582 512 x 492 752 x 492 768 x 492
Imager 1/3" interline CCD
Resolution 330 TV lines 480 TV lines
Minimum illumination <0.7 lux <0.8 lux

<0.3 lux with Nightsense™
Signal-to-noise ratio > 50 dB
Video output 1 Vpp, 75 Ω
Y/C output NA Y: 1 Vpp, 75 Ω;

C: 0.3 Vpp 75 Ω
Synchronization Internal or Line-Lock (selectable)
Shutter Auto / Flickerless / Off (selectable)

PAL: 1/50 - 1/125000 - NTSC: 1/60 - 1/150000
Nightsense™ NA Auto / Forced / Off (selectable)
Autoblack On / Off (selectable)
AGC On (0-21 dB)/ Off (0 dB) (selectable)
BLC On / Off (selectable)
ATW Auto/Hold selectable 2500 to 9000 K
Lens mount C and CS compatible
ALC Video-iris or DC-iris (auto detect)
Power supply LTC 04x5/10 & /20: 12 to 28 VAC or 11 to 36 VDC

LTC 04x5/50 & /60: 85 to 265 VAC
Power consumption <4 W
Dimensions (HxWxL) 58 x 66 x 122 mm (2.28 x 2.6 x 4.8 inch without lens)
Weight 450 g (0.99 lbs) (without lens)
Camera mount Two 1/4" 20 UNC - isolated (bottom) and

non-isolated (top)
Operating temperature -20°C to +50°C (-4°F to +122°F)
Controls On-screen display (OSD) with softkey controls

Type number overview

Low voltage High voltage

PAL (Europe) NTSC (USA) PAL (Europe) NTSC (USA)
Standard resolution LTC 0435/10 LTC 0435/20 LTC 0435/50 LTC 0435/60
High resolution LTC 0455/10 LTC 0455/20 LTC 0455/50 LTC 0455/60

EN1

English

Genion_ii_00111.qxd 7/4/02 11:39 AM Page EN1

UNPACKING

Unpack carefully and handle the equipment with care. The packaging contains:

• Camera

• CCD protection cap

• Spare lens connector (male)

• These Instructions
Note: If equipment appears to have been damaged during shipment, repack it in the

original packaging and notify the shipping agent or supplier.

CONNECTION
Power

LTC 04x5/10 and /20 LTC 04x5/50 and /60

To open the quick-connect, push in on the tabs.
Connections are not polarity sensitive
Use stranded or solid wire AWG16 to
AWG22, cut back 10mm (0.4") of
insulation.

Composite Video

EN2

English

Genion_ii_00111.qxd 7/4/02 11:39 AM Page EN2

Y/C output (LTC 0455/x0 only)

Pin Y/C Socket
1 GND Y
2 GND C
3Y
4C

LENS MOUNTING

Pin Video iris lens DC iris lens
1 Supply (11 V, 50 mA max.) Damp­2 Not used Damp+
3 Video signal 1 Vpp, 1 kΩ Drive+
4 Ground Drive-

• Video-iris and DC-iris lenses are recommended for the best picture performance.

• The camera automatically detects the type of lens used, and optimizes
performance accordingly.

• A spare male lens connector is provided if required.

Cautions:

- To avoid damaging the CCD sensor when using a C-mount lens, turn the 'green'
back-focus ring counter clockwise until it stops ('Back focus adjustment') before
mounting the lens.

- Lenses weighing more than 0.5 kg (1.1lbs) must be separately supported.

Note: If a short circuit is detected on the lens connector, the on-screen display (OSD)

failure message 'LENS SHORT CIRCUIT' is shown. The lens circuit is
automatically disabled to avoid internal damage. Remove the lens connector and
check the pin connections.

EN3

English

Genion_ii_00111.qxd 7/4/02 11:39 AM Page EN3

Back focus adjustment

• Camera accepts both C and CS-mount lenses.

1. Unlock the back focus locking
button.

2. Turn the back focus adjustment as
required. (See Note 1).

3. Lock the back focus locking button.

Notes:

1. To optimize picture sharpness in
both bright and low-level lighting, it
is recommended to adjust the back
focus when carrying out the set-up
procedure. The camera's unique
'Lens Wizard' allows focusing at
maximum lens opening to ensure
that the object of interest always
remains in focus.

2. When back focusing vari-focus lenses, it must be possible to obtain a sharp
picture in both wide-angle and tele positions, and for both far and near focus.

3. When back focusing zoom lenses, ensure the object of interest remains in focus
throughout the entire zoom range of the lens. (See Advanced Set up).

Caution: Do not point the camera/lens into direct sunlight. When viewing an

outdoor scene, a video- or DC-iris lens is recommended.

MOUNTING THE CAMERA

The camera can be mounted from the
top or bottom.
Note: The BOTTOM mounting is

isolated from ground.

EN4

English

Genion_ii_00111.qxd 7/4/02 11:39 AM Page EN4

ADVANCED SET-UP

The camera will normally give an optimal picture without the need for further
adjustments. However for special circumstances advanced set up options are available.

Accessing and navigating menus

• Five softkeys are used for navigating
menus (located under the side panel).

• To access set-up menus, press the
menu/select key.

• The main menu appears on the OSD.

•

Key Function
Menu button (O) Access the menus, or move to next or previous menu.

← → Toggle through options, set parameters
↑ ↓ Scroll up and down menu

Note: A downward-pointing arrow ( ) indicates a sub-menu follows.

↓

EN5

English

Genion_ii_00111.qxd 7/4/02 11:39 AM Page EN5

Menu Navigation

MAIN MENU

LEVEL 0
SHUT/AGC
BLC OFF
COLOR ATW
SYNC LINE LOCK
VPHASE 0°

EXIT

EN6

English

Press the menu button

Press the menu button
for more than 5sec.

Main Menu

Shutter/AGC Menu

Color Menu

Installer Menu

Lens Wizard Menus

SHUT/AGC MENU

SHUTTER AES

AGC ON

AUTOBLACK ON

NIGHTSENSE OFF

EXIT

COLOR MENU

WHITE BAL ATW

RED-GAIN 0

BLUE-GAIN 0

EXIT

INSTALLER

VERSION 00.0010.XX

LENS AUTO
SPEED FAST
WIZARD

DEFAULTS

EXIT

LENS WIZARD

DETECTED LENS VIDEO

SET BACK FOCUS NOW

SET LVL

EXIT

LENS WIZARD

DETECTED LENS DCIRIS

SET BACK FOCUS NOW

EXIT

Genion_ii_00111.qxd 7/4/02 11:39 AM Page EN6

Main menu

Function Selection Description
LEVEL -15 - 0 - +15 Adjusts video level.
SHUT/AGC Select next menu Shutter / Automatic Gain Control menu.
BLC ON When 'ON', the level is optimized at the center of

OFF the screen. Parts outside the center may be under- or

over-exposed (this is normal).

COLOR* ATW Select to access the color menu. (See Color menu

ATB HOLD for detailed explanation).
Select next menu

SYNC LINE LOCK Select 'LINE LOCK' to synchronize with the power

INTERNAL supply frequency. Select 'INTERNAL' for use with

internal synchronization (automatically selected with
DC supply).

V PHASE 0-358˚ Adjusts the vertical phase offset (when in

'LINE LOCK' mode).

EXIT Exit the menu.

*Note: If the camera (LTC 0455/x0 only) is in black & white high sensitivity mode

(via NightSense™), the color settings and color menu are not accessible. The
NightSense™ sensitivity boost must be selected OFF to make color adjustments.

Shutter/AGC menu

Function Selection Description
SHUTTER AES (AES) Auto-shutter sets the optimum shutter speed

FL for manual iris lenses. (FL) Flickerless mode avoids
OFF interference from light sources (recommended for use

with video-iris or DC-iris lenses only).
AGC ON/OFF Automatic gain control
AUTOBLACK ON/OFF Autoblack automatically increases the visibility

of details.
NIGHTSENSE AUTO Nightsense™* extends the low-light

FORCED performance of the camera. AUTO mode, the
OFF camera automatically inches to monochrome

in low-light conditions. In Forced mode, the picture

remains a high-sensitivity monochrome image.

Some active noise or white spots may appear in the

picture.
EXIT Exit this menu.

*Note: NightSense™ is only available on the LTC 0455/x0 cameras.

EN7

English

Genion_ii_00111.qxd 7/4/02 11:39 AM Page EN7

Color menu

Note: Auto Tracking White Balance must be selected OFF.

Function Selection Description
WHITE BAL ATW ATW: Auto tracking white balance allows the

AWB HOLD camera to constantly adjust for optimal color

reproduction.
AWB HOLD: Puts the ATW on hold and saves
the color settings.

RED- GAIN* -5 - 0 - +5 Offset factory white point alignment (reducing

red introduces more cyan).

BLUE- GAIN* -5 - 0 - +5 Offset factory white point alignment (reducing

blue introduces more yellow).

EXIT Exit the menu.

*Note: For special scene conditions only, it will be necessary to change the white
point offsets.

Accessing installer menu

• To access the installer menu, press and hold the menu/select key for five seconds.

Installer menu

Function Selection Description
VERSION Read-only firmware release number (for service

purposes).

LENS AUTO Automatically detect lens type.

A different lens type can be selected.

SPEED FAST Selects the response time of DC-iris lenses. Some

lenses require slow lens control to avoid overshoots.
WIZARD Access the lens wizard menu.
DEFAULTS Select next menu Return all set-up settings to factory defaults.
EXIT Exit the menu.

EN8

English

Genion_ii_00111.qxd 7/4/02 11:39 AM Page EN8

Lens wizard menu

Function Description
SET BACK FOCUS NOW Back focus the lens (see 'Back focus adjustment'). The scene is

focused at maximum lens opening to ensure that the object of
interest remains in focus in bright and low-light conditions.

SET LVL When a Video-iris lens is detected, a level potentiometer is

displayed to obtain the best picture performance. The lens
wizard includes a level detector meter that must be set to the
center using the potentiometer for best results.

EXIT Exit the menu.

Adjustment procedure DC-iris Lens:

1. Unlock the back focus locking button.

2. Access the "Lens Wizard" menu.

3. The "SET BACK FOCUS NOW" option is highlighted in the menu.

4. Turn the back focus adjustment as required.

5. Lock the back focus locking button.

6. Exit the menu.

Adjustment procedure Manual-iris Lens:

1. Unlock the back focus locking button.

2. Adjust the lens to the maximum lens opening.

3. Turn the back focus adjustment as required.

4. Lock the back focus locking button.

5. Exit the menu.

Adjustment procedure Video-iris Lens:

1. Unlock the back focus locking button.

2. Access the "Lens Wizard" menu.

3. The "SET BACK FOCUS NOW" option is highlighted in the menu.

4. Turn the back focus adjustment as required.

5. Select the "SET LVL" option in the menu, and the LEVEL bar appears.

6. Adjust the level potentiometer located on the lens until the LEVEL bar is in the

central position.

7. Lock the back focus locking button.

8. Exit the menu.

EN9

English

Genion_ii_00111.qxd 7/4/02 11:39 AM Page EN9

EN10

English

Genion_ii_00111.qxd 7/4/02 11:39 AM Page EN10