Philips I74F112N Datasheet
INTEGRATED CIRCUITS
74F112
Dual J-K negative edge-triggered flip-flop
Product specification
IC15 Data Handbook
1990 Feb 09
Philips Semiconductors Product specification
74F1 12Dual J-K negative edge-triggered flip-flop
FEA TURE
PIN CONFIGURATION
•Industrial temperature range available (–40°C to +85°C)
1
0
CP
2
DESCRIPTION
The 74F112, Dual Negative Edge-Triggered JK-Type Flip-Flop,
feature individual J, K, Clock (CP
inputs, true (Qn) and complementary (Q
The SD and RD inputs, when Low, set or reset the outputs as shown
in the Function Table, regardless of the level at the other inputs.
A High level on the clock (CP
n), Set (SD) and Reset (RD)
n) outputs.
n) input enables the J and K inputs and
K0
J0
3
S
4
D0
5
Q0
0
6
Q
Q
1
data will be accepted. The logic levels at the J and K inputs may be
allowed to change while the CP
n is High and flip-flop will perform
according to the Function Table as long as minimum setup and hold
times are observed. Output changes are initiated by the High-to-Low
transition of the CP
n.
TYPE TYPICAL PROPAGATION DELAY TYPICAL SUPPLY CURRENT (TOTAL)
74F112 100MHz 15mA
ORDERING INFORMATION
ORDER CODE
DESCRIPTION
16-pin plastic DIP N74F112N I74F1 12N SOT38-4
16-pin plastic SO N74F112D I74F1 12D SOT109-1
COMMERCIAL RANGE
VCC = 5V ±10%, T
= 0°C to +70°C
amb
VCC = 5V ±10%, T
INDUSTRIAL RANGE
= –40°C to +85°C
amb
16
15
14
13
12
11
107
98GND Q1
SF00103
V
R
R
CP1
K1
J1
SD1
CC
D0
D1
PKG DWG #
INPUT AND OUTPUT LOADING AND FAN-OUT TABLE
PINS DESCRIPTION 74F (U.L.) HIGH/LOW LOAD VALUE HIGH/LOW
J0, J1 J inputs 1.0/1.0 20µA/0.6mA
K0, K1 K inputs 1.0/1.0 20µA/0.6mA
SD0, SD1 Set inputs (active Low) 1.0/5.0 20µA/3.0mA
RD0, RD1 Reset inputs (active Low) 1.0/5.0 20µA/3.0mA
CP0, CP1 Clock Pulse input (active falling edge) 1.0/4.0 20µA/2.4mA
Q0, Q0; Q1, Q1 Data outputs 50/33 1.0mA/20mA
NOTE:
One (1.0) FAST unit load is defined as: 20µA in the High state and 0.6mA in the Low state.
February 9, 1990 853–0338 98775
2
Philips Semiconductors Product specification
OPERATING MODE
74F112Dual J-K negative edge-triggered flip-flop
LOGIC SYMBOL
1
4
15
13
10
14
VCC = Pin 16
GND = Pin 8
LOGIC DIAGRAM
311
J1 K0
CP0
SD0
RD0
CP1
SD1
RD1
Q0 Q0 Q1 Q1
56 97
Qn
4, 10
S
Dn
2, 12
Kn
212
SF00104
5, 9
IEC/IEEE SYMBOL
3
1
K1J0
2
15
4
11
13
12
14
10
1J
C1
1K
R
S
2J
C2
2K
R
S
6, 7
n
Q
15, 14
R
Dn
3, 11
Jn
5
6
9
7
SF00105
VCC = Pin 16
GND = Pin 8
CP
1, 13
n
FUNCTION TABLE
INPUTS OUTPUTS
SD RD CP J K Q Q
L H X X X H L Asynchronous Set
H L X X X L H Asynchronous Reset
L L X X X H* H* Undetermined *
H H ↓ h h q q Toggle
H H ↓ l h L H Load “0” (Reset)
H H ↓ h l H L Load “1” (Set)
H H ↓ l l q q Hold “no change”
H H H X X Q Q Hold “no change”
H = High voltage level
h = High voltage level one setup time prior to High-to-Low clock transition
L = Low voltage level
l = Low voltage level one setup time prior to High-to-Low clock transition
q = Lower case letters indicate the state of the reference output prior to the High-to-Low clock transition
X = Don’t care
↓ = High-to-Low clock transition
* = Both outputs will be High while both S
D and RD are Low, but the output states are unpredictable if SD and RD go High simultaneously.
SF00106
February 9, 1990
3
Loading...