Philips HTS-5310-K Service Manual
DVD Receiver
CLASS 1
LASER PRODUCT
HTS3500K/51 & HTS5310K/51
Contents Page
1 Technical Specifications and Connection
Facilities 2
2 Measurements Setup, Service Aid &
Lead Free Requirements 4
3 Direction For Use 8
4 Dismantling Instructions & Service Positions 12
5 Service Test Program 14
6 FTD Display Pin Connection 16
7 Block Diagram 17
Wiring Diagram 18
8 Circuit Diagram and PWB Layout 19
Front: Display 19
Front: Display (Top view) 20
Front: Display (Bottom view) 21
Front: Standby 22
Mono Board: Circuit Diagram (Part 1) 23
Mono Board: Circuit Diagram (Part 2) 24
Mono Board: Circuit Diagram (Part 3) 25
Mono Board: Circuit Diagram (Part 4) 26
Mono Board: Circuit Diagram (Part 5) 27
Mono Board: Circuit Diagram (Part 6) 28
Mono Board: Circuit Diagram (Part 7) 29
Mono Board: Circuit Diagram (Part 8) 30
Mono Board: Circuit Diagram (Part 9) 31
Layout: Mono Board (Top View) 32
Layout: Mono Board (Bottom View) 33
PSU Circuit Diagram 34
©
Copyright 2005 Philips Consumer Electronics B.V. Eindhoven, The Netherlands.
All rights reserved. No part of this publication may be reproduced, stored in
a retrieval system or transmitted, in any form or by any means, electronic,
mechanical, photocopying, or otherwise without the prior permission of Philips.
Contents Page
9 Exploded View & Spare Parts List 35
Exploded View of the set 35
Spare Part List 36
Published by KC-TE 0749 AV Systems Printed in he Netherlands Subject to modification EN 3139 785 31641
Version 1.1
EN 2
3139 785 31640
LOCATION OF PC BOARDS
HTS3500K/HTS5310K
1.
Technical Specifications and Connection Facilities
VERSION V
Video (Yellow, Cinch) x x
Component V
Digital In - Coaxial x x
TV In (Left/Right) x x
Auxiliary (Left/Right) x x
Line out (Audio) x
S-V
Progessive Scan x
ARIATIONS:
HTS3300K & HTS3610k HTS3500K & HTS5310k
ideo Output, (Y/Pb/Pr) x x
ideo Output x
Technical Specifications and Connection Facilities
1. Specifications
3139 785 31640
1.
EN 3
1.1 General:
Mains voltage : 230V
Mains frequency : 50Hz
Power consumption : 100W
< 0.5W Eco standby
power
< 100W at 1/8 P
(For main unit)
Dimension main unit : 360 x 54 x 324mm
rated
1.2 Tuner
FM
Tuning range : 87.5-108MHz
Grid : 50kHz
IF frequency : 10.7MHz ± 25kHz
Aerial input : 75Ω coaxial
Sensitivity at 26dB S/N : < 7µV
Selectivity at 600kHz bandwidth : > 25dB
IF rejection : > 60dB
Image rejection : > 25dB
Distortion at RF=1mV, dev. 75kHz : < 3%
-3dB Limiting point : < 8µV
Crosstalk at RF=1mV, dev. 67.5kHz : > 28dB
Crosstalk at RF=1mV, dev. 40kHz : > 18dB
MW
Tuning range : 531-1602kHz
Grid : 9kHz
IF frequency : 450kHz ± 1kHz
Aerial input : Frame aerial
Sensitivity at 26dB S/N : < 4.0mV/M
Selectivity at 18kHz bandwidth : > 20dB
IF rejection : > 45dB
Image rejection : > 28dB
Distortion at RF=50mV, m=80% : < 5%
1.3 AMPLIFIER:
Output power
Front : 100W RMS / channel
Rear : 75W RMS / channel
Center : 100W RMS
Subwoofer : 150W RMS
Frequency response ±0.5dB : 20Hz-20kHz
Hum (Volume Minimum) : 200nW
Residual noise (Volume Minimum) : 40nW
Input sensitivity
Aux In : 1V ± 3dB at 22kΩ
Scart In : 1V ± 3dB at 22kΩ
Output sensitivity
Line Out (Left/Right) : 1V ± 2dB at 10kΩ
Scart Out (Left/Right) : 1V ± 2dB at 10kΩ
1.4 COMPACT DISC/VCD/DVD:
Video Decoding : MPEG-1/MPEG-2/
MPEG-4/DivX 3.11,
4.x & 5.x
Video DAC : 12 Bits
Signal System : PAL / NTSC
Video Format : 4:3 / 16:9
CVBS Out
CVBS level : 1.0 ± 0.1V
Luminance S/N : >= 60dB
S-Video Out 1)
Y level : 1.0 ± 0.1V
Y S/N : >= 60dB
C level (burst) : 286mV pp +1/-4 dB
1)
p-p
p-p
RGB/YUV Out 1)
Amplitude : 1.0 ± 0.1V
S/N : >= 60dB
1)
Output terminals to be terminated with 75Ω
p-p
EN 4
3139 785 31640
LF Generator
e.g. PM5110
Recorder
Use Universal Test Cassette CrO2 SBC419 4822 397 30069
LEVEL METER
e.g. Sennheiser UPM550
with FF-filter
S/N and distortion meter
e.g. Sound Technology ST1700B
L
R
DUT
or Universal Test Cassette
Fe SBC420 4822 397 30071
LEVEL METER
e.g. Sennheiser UPM550
with FF-filter
S/N and distortion meter
e.g. Sound Technology ST1700B
L
R
DUT
CD
Use Audio Signal Disc
(replaces test disc 3)
SBC429 4822 397 30184
Bandpass
250Hz-15kHz
e.g. 7122 707 48001
LF Voltmeter
e.g. PM2534
DUT
S/N and distortion meter
e.g. Sound Technology ST1700B
Frame aerial
e.g. 7122 707 89001
Tuner AM (MW,LW)
To avoid atmospheric interference all AM-measurements have to be carried out in a Faraday´s cage.
Use a bandpass filter (or at least a high pass filter with 250Hz) to eliminate hum (50Hz, 100Hz).
RF Generator
e.g. PM5326
Ri=50Ω
Bandpass
250Hz-15kHz
e.g. 7122 707 48001
LF Voltmeter
e.g. PM2534
DUT
RF Generator
e.g. PM5326
S/N and distortion meter
e.g. Sound Technology ST1700B
Use a bandpass filter to eliminate hum (50Hz, 100Hz) and disturbance from the pilottone (19kHz, 38kHz).
Ri=50Ω
Tuner FM
MEASUREMENT SETUP
2.
Measurements Setup, Service Aid & Lead Free Requirements
2. Measurements Setup, Service Aid & Lead Free Requirements
Measurements Setup, Service Aid & Lead Free Requirements
HANDLING CHIP COMPONENTS
SERVICE AIDS
Service Tools:
Universal Torx driver holder .................................. 4822 395 91019
Torx bit T10 150mm ............................................. 4822 395 50456
Torx driver set T6 - T20 ......................................... 4822 395 50145
Torx driver T10 extended ...................................... 4822 395 50423
Compact Disc:
SBC426/426A Test disc 5 + 5A ............................ 4822 397 30096
SBC442 Audio Burn-in Test disc 1kHz ................. 4822 397 30155
SBC429 Audio Signals disc .................................. 4822 397 30184
Dolby Pro-logic Test Disc ...................................... 4822 395 10216
3139 785 31640
2.
EN 5
EN 6
3139 785 31640
GB
WARNING
All ICs and many other semi-conductors are
susceptible to electrostatic discharges (ESD).
C
areless handling during repair can reduce life
drastically.
When repairing, make sure that you are
connected with the same potential as the mass
of the set via a wrist wrap with resistance.
Keep components and tools also at this
potential.
F
ATTENTION
Tous les IC et beaucoup d’autres
semi-conducteurs sont sensibles aux
décharges statiques (ESD).
Leur longévité pourrait être considérablement
écourtée par le fait qu’aucune précaution n’est
p
rise à leur manipulation.
L
ors de réparations, s’assurer de bien être relié
au même potentiel que la masse de l’appareil et
enfiler le bracelet serti d’une résistance de
sécurité.
V
eiller à ce que les composants ainsi que les
outils que l’on utilise soient également à ce
potentiel.
ESD
D
WARNUNG
Alle ICs und viele andere Halbleiter sind
empfindlich gegenüber elektrostatischen
Entladungen (ESD).
Unsorgfältige Behandlung im Reparaturfall kan
d
ie Lebensdauer drastisch reduzieren.
Veranlassen Sie, dass Sie im Reparaturfall über
ein Pulsarmband mit Widerstand verbunden
s
ind mit dem gleichen Potential wie die Masse
des Gerätes.
B
auteile und Hilfsmittel auch auf dieses gleiche
Potential halten.
NL
WAARSCHUWING
Alle IC’s en vele andere halfgeleiders zijn
gevoelig voor electrostatische ontladingen (ESD).
Onzorgvuldig behandelen tijdens reparatie kan
d
e levensduur drastisch doen verminderen.
Zorg ervoor dat u tijdens reparatie via een
polsband met weerstand verbonden bent met
h
etzelfde potentiaal als de massa van het
apparaat.
H
oud componenten en hulpmiddelen ook op
ditzelfde potentiaal.
I
AVVERTIMENTO
Tutti IC e parecchi semi-conduttori sono
se
nsibili alle scariche statiche (ESD).
L
a loro longevità potrebbe essere fortemente
ridatta in caso di non osservazione della più
g
rande cauzione alla loro manipolazione.
Durante le riparazioni occorre quindi essere
collegato allo stesso potenziale che quello della
massa dell’apparecchio tramite un braccialetto
a resistenza.
Assicurarsi che i componenti e anche gli utensili
co
n quali si lavora siano anche a questo
potenziale.
GB
ESD PROTECTION EQUIPMENT:
Complete Kit ESD3 (small tablemat, wristband,
connection box, extention cable and earth cable) ...........4822 310 10671
Wristband tester ....................................................................4822 344 13999
CLASS 1
LASER PRODUCT
GB
Warning !
Invisible laser radiation when open.
Avoid direct exposure to beam.
S
Varning !
Osynlig laserstrålning när apparaten är öppnad och spärren
är urkopplad. Betrakta ej strålen.
SF
Varoitus !
Avatussa laitteessa ja suojalukituksen ohitettaessa olet alttiina
näkymättömälle laserisäteilylle. Älä katso säteeseen!
DK
Advarse !
Usynlig laserstråling ved åbning når sikkerhedsafbrydere er
ude af funktion. Undgå udsaettelse for stråling.
F
"Pour votre sécurité, ces documents doivent être utilisés par
des spécialistes agréés, seuls habilités à réparer votre
appareil en panne".
GB
Safety regulations require that the set be restored to its original
condition and that parts which are identical with those specified,
be used
Safety components are marked by the symbol
!
.
NL
Veiligheidsbepalingen vereisen, dat het apparaat bij reparatie in
zijn oorspronkelijke toestand wordt teruggebracht en dat onderdelen,
i
dentiek aan de gespecificeerde, worden toegepast.
D
e Veiligheidsonderdelen zijn aangeduid met het symbool
!
F
Les normes de sécurité exigent que l’appareil soit remis à l’état
d’origine et que soient utiliséés les piéces de rechange identiques
à celles spécifiées.
Less composants de sécurité sont marqués
!
D
Bei jeder Reparatur sind die geltenden Sicherheitsvorschriften zu
beachten. Der Original zustand des Geräts darf nicht verändert werden;
für Reparaturen sind Original-Ersatzteile zu verwenden.
S
icherheitsbauteile sind durch das Symbol
!
markiert.
I
Le norme di sicurezza esigono che l’apparecchio venga rimesso
nelle condizioni originali e che siano utilizzati i pezzi di ricambio
identici a quelli specificati.
Componenty di sicurezza sono marcati con
!
GB
After servicing and before returning set to customer perform a leakage
current measurement test from all exposed metal parts to earth ground to
assure no shock hazard exist. The leakage current must not exceed
0.5mA.
2.
Measurements Setup, Service Aid & Lead Free Requirements
Measurements Setup, Service Aid & Lead Free Requirements
2.1 Lead Free Requirements
3139 785 31640
2.
EN 7
Pb(Lead) Free Solder
When soldering , be sure to use the pb free solder.
INDENTIFICATION:
Regardless of special logo (not always indicated)
one must treat all sets from 1 Jan 2005 onwards, according next
rules:
Important note: In fact also products of year 2004 must be treated in
this way as long as you avoid mixing solder-alloys (leaded/ lead-free).
So best to always use SAC305 and the higher temperatures belong
to this.
Due to lead-free technology some rules have to be respected by the
workshop during a repair:
• Use only lead-free solder alloy Philips SAC305 with order
code 0622 149 00106. If lead-free solder-paste is required,
please contact the manufacturer of your solder-equipment.
In general use of solder-paste within workshops should be
avoided because paste is not easy to store and to handle.
• Use only adequate solder tools applicable for lead-free solder
alloy. The solder tool must be able
o To reach at least a solder-temperature of 400°C,
o To stabilize the adjusted temperature at the solder-tip
o To exchange solder-tips for different applications.
• Adjust your solder tool so that a temperature around 360°C
– 380°C is reached and stabilized at the solder joint. Heatingtime of the solder-joint should not exceed ~ 4 sec. Avoid
temperatures above 400°C otherwise wear-out of tips will rise
drastically and flux-fluid will be destroyed. To avoid wear-out
of tips switch off un-used equipment, or reduce heat.
• Mix of lead-free solder alloy / parts with leaded solder alloy /
parts is possible but PHILIPS recommends strongly to avoid
mixed solder alloy types (leaded and lead-free).
If one cannot avoid or does not know whether product is leadfree, clean carefully the solder-joint from old solder alloy and
re-solder with new solder alloy (SAC305).
• Use only original spare-parts listed in the Service-Manuals.
Not listed standard-material (commodities) has to be
purchased at external companies.
• Special information for BGA-ICs:
- always use the 12nc-recognizable soldering temperature
profile of the specific BGA (for de-soldering always use the
lead-free temperature profile, in case of doubt)
- lead free BGA-ICs will be delivered in so-called ‘drypackaging’ (sealed pack including a silica gel pack) to protect
the IC against moisture. After opening, dependent of MSLlevel seen on indicator-label in the bag, the BGA-IC possibly
still has to be baked dry. (MSL=Moisture Sensitivity Level).
This will be communicated via AYS-website.
Do not re-use BGAs at all.
• For sets produced before 1.1.2005 (except products of 2004),
containing leaded solder-alloy and components, all needed
spare-parts will be available till the end of the service-period.
For repair of such sets nothing changes.
• On our website www.atyourservice.ce.Philips.com you find
more information to:
BGA-de-/soldering (+ baking instructions)
Heating-profiles of BGAs and other ICs used in
Philips-sets
You will find this and more technical information within the
“magazine”, chapter “workshop news”.
For additional questions please contact your local repair-helpdesk.
EN 8
3139 785 31640
QUICK START GUIDE
12nc: 3139 246 19191
HTS3500K
1 what’s in the box
2 connect TV
3 connect subwoofer, speakers and antennas
3a Placement of speakers
3c Connect the
FM and MW
antennas
REAR L
REAR R
FRONT L
CENTER
FRONT R
Subwoofer
TV
3b Connect the speakers
and subwoofer to the
DVD system
(refer to the user manual for
“Individual speaker volume
adjustment”)
3d Connect the mains
cord to the power
supply
Pb
Pr
Y
L NE OUT
TV IN AUX N
�
REAR L
REAR R
CENTE R
FRONT L
FRONT R
Note: For connecting to a Progressive Scan TV,
refer to the user manual for proper
connections and detailed set up.
A
Remote control
includes 2x AA batteries
D
B
G H
C
Subwoofer
FM wire
antenna
MW loop
antenna
Main unit
Front/Rear/Center speakers
Video cable
E
Audio cable
F
A
H
G
E
A
3.
Directions For Use
3. Directions For Use
The following except of the Quick Use Guide serves as an introduction to the set.
The Complete Direction for the Use can be downloaded in different languages from the internet site of Philips Customer care Center:
www.p4c.philips.com
4 play a disc
DISC
4a Press DISC.
Point the remote control
towards the DVD system.
4b Load in a disc
Press OPEN CLOSE to
open and close the disc
tray.
4c Select correct
AV In channel
Switch to the correct
input source by using the
TV remote control.
GET PICTURE
•
Check the connection of the DVD system
to TV is in place (see 2 Connect TV).
• Check the AV mode on TV. It may be
called FRONT, A/V IN, or VIDEO. Choose
the different modes using TV remote
control.
• Or, use the TV remote control to select
Channel 1 on TV, then press Channel down
button until you get the picture.
• See your TV manual for more details.
A
udio Se
tup
P
age
S
p
eakers
V
olume
S
p
eakers
D
ela
y
N
ight
M
od
e
CD
U
psampling
V
ideo Se
tup
P
age
TV
T
ype
TV
D
ispla
y
P
rogressiv
e
P
ictur
e
S
etti
ng
P
reference
P
age
A
udio
S
ubtitl
e
D
isc
M
e
nu
P
arental
PBC
MP3/JPEG
N
a
v
P
asswor
d
D
i
v
X S
ubtitl
e
D
efaul
t
G
enera
l Se
tup
P
age
D
isc
L
o
ck
D
ispla
y
D
i
m
P
rogram
OSD L
a
nguag
e
S
cree
n
S
ave
r
DIVX(R) VOD
C
od
e
Refer to chapter “DVD Setup Menu Options” in the user manual
for detailed descriptions.
More settings and features
GET SOUND
To enhance the sound
quality
Press SOUND button to
select a predefined digital
sound effect.
Detailed playback features and additional
functions are described in the user man
ual.
No sound from rear
speakers?
Press SURR button to select
“Multi-Channel”.
5 programme radio stations
6 optional - connect VCR
IN 1 IN 2
NEEDS HELP? Visit our website www.philips.com/support
5a Press TUNER.
5b Press and hold PLAY 2
until “
START ...” appears.
It will start to pr
ogramme
all available radio stations.
5c Once complete, use
S / T to select a
preset
radio station.
Note: This feature is only available
for first time setup.
Note: LINE OUT will output sound only when the speakers
volume are reduced to level 1 and below.
Directions For Use
3139 785 31640
3.
EN 9
EN 10
3139 785 31640
Quick Start Guide
HTS 5310K
What’s in the Box
Home Theatre System
Need help?
User Manual
For more product information refer to the user
manual of the home theatre system.
Online
Go to www.philips.com/support
2005 © Koninklijie Philips N.V.
All rights reserved.
12 NC 31 39 246 19181
www.philips.com
Troubleshooting
For more troubleshooting tips, see the user manual.
Problem Tip
No power • Check if the AC power cord is properly connected.
• Press the STANDBY-ON on the front of the DVD system to turn on the power.
No picture • Press DISC on remote control.
• Check connection to TV and ensure the plugs are firmly in place.
No sound or • Adjust the volume.
distorted sound • Check the speaker connections and settings.
• Check audio connections and press SOURCE button to select the correct input source.
Remote control • Check that the batteries are loaded correctly or replace the batteries with new ones.
does not work • Select the source (DISC or TUNER, for example) before pressing the function button.
• Reduce the distance between the remote control and the system.
• Point the remote control directly toward the IR sensor.
DVD system
Audio cables
(red & white plugs)
Video cables
(yellow plug)
Rear speakers
(left & right)
Listen to Radio
1 Press TUNER .
2 Press and hold PLAY until‘START’ appears.
Tip This feature is only availa-
ble for first time setup, refer
to user manual if you wish to
program radio stations again
or for manual programming.
3 Once completed you can use NEXT or
PREVIOUS to select a radio station.
Front display
Remote control
and 2 batteries
Quick start guide
Centre speaker
Subwoofer
Play DVD
1 Press OPEN/CLOSE on the front of
the DVD system to open the disc tray.
2 Place DVD in tray with the label facing up.
3 Press OPEN/CLOSE again.
4 Press UP , DOWN , RIGHT or
LEFT to scroll through the options in
the DVD menu.
5 Press PLAY on the option you want.
6 To stop press STOP .
Tip Press PLAY to resume from where
you stopped or press STOP and PLAY
to start from the beginning of the title.
7 Press DISC MENU to go back to the
DVD menu.
DVD Player (front)
Front speakers
(left & right)
Experience Surround Sound
1 Press SURR to switch between Stereo and
Multi-channel.
2 Press SOUND for either Concert, Drama,
Action or Sci-fi preset digital sound effects.
AM/MW
loop antenna
FM wire antenna
User manual
3.
Directions For Use
EN 11
Connect Speakers &
Subwoofer to DVD System
Connect the various coloured plugs from the
speakers and subwoofer to the same colour
socket on the rear of DVD system.
Fix Antennas
1 Connect the FM antenna to the FM socket,
extend the antenna and fix it on the wall.
DVD System (back)
2 Unfold the AM/ MW loop antenna and fix the
claw into the slot.
3 Push back tab and insert each wire into slot.
Position Speakers &
Subwoofer
1 Place centre speaker on or close to the TV.
2 Place subwoofer on the floor.
3 Place front speakers equal distance from the
TV and angle them 45 degree to the listener.
4 Place rear speakers facing the listener, equal
distance on the left and right.
Insert Batteries in
Remote Control
1 Remove batteries compartment cover.
2 Insert the provided batteries in the remote
control.Take note of where the positive and
negative ends should go.
3 Replace the batteries compartment cover.
Remote Control (back)
Find Correct Viewing Channel
1 Press STANDBY-ON on the DVD
system’s remote control.
2 Press DISC on the
remote control until ‘DISC’
appears on the front panel.
3 Switch on the TV.
4 Press ‘0’ on theTV’s remote
control, then repeatedly
press the Channel Down
button until you see the
DVD background screen.
This is the correct viewing
channel for the home
theatre system.
Tip For some TVs, to find the
correct viewing channel, you
can keep pressing the AV or
the SELECT buttons. If still
unable to find the correct
viewing channel, check the
connections again or check
your TV’s user manual.
MW loop
antenna
DVD System (back)
Connect DVD system to TV
1 Use the yellow Video cable to connect the
yellow CVBS socket on the rear of the DVD
system and the yellowVIDEO IN jack at the
rear of the TV.
2 Plug in the power cable of the DVD system
to an AC outlet.
Tip To connect other devices
to the DVD system, refer to
the use manual.
To antenna
or set-top
box
Rear
Speaker
(left)
Rear
Speaker
(right)
Front
Speaker
(right)
Front
Speaker
(left)
Centre
Speaker
Pb
r
DVD System (back)
Sub-Woofer
Connect Audio from TV
to DVD System (Optional)
Use the red & white audio cables to connect
the red & white TV-IN sockets on the rear of
the DVD system and the red & white AUDIO
OUT sockets on the TV.
DVD System (back)
Television (back)
DO O
VIDEOOUT
(CVBS)
AUDIOOUT
r
Y
DO N
B
VIDEO IN
(CVBS)
Pb
Y
DVD System (back)
Television (back)
Tip SomeTVs may not
have anAUDIO OUT jack.
Directions For Use
3139 785 31640
3.
EN 12
3139 785 31640
4.
Dismantling Instructions & Service Positions
4. Dismantling Instructions
4.1 Dismantling of the DVD Loader
1) The tray can be manually open by inserting a minus
screw drive and push the lever in the direction as shown
in Figure 4-1 to unlock the tray before sliding it out.
Figure 4-1
2) Slide out the tray and remove the Cover Tray (pos 110)
as shown in Figure 4-2.
4.2 Dismantling of the Tuner Module,
MONO Board, Front Board, PSU Module
1) Loosen 1 screw A (see Figure 4-3) to remove the Tuner
Module (pos 1040).
2) Loosen 9 screws B (see Figure 4-3) and 4 screws
(see Figure 3-4) to remove MONO Board.
3) Release 4 snap hooks to remove Front Board.
- 1 snap hook each on the left & right side (pos 161).
- 2 snap hooks on the bottom side (pos 161).
4) Loosen 4 screws E (see Figure 4-4) to remove the
PSU Module.
B
Figure 4-3
B
B
A
Figure 4-2
3) Loosen 5 screws to remove the Front Top.(pos 240)
- 1 screw each on the left & right side (pos 272)
- 3 screws behind
4) Loosen 4 screws C (see Figure 4-4) to remove the DVD
Loader.
E
C
D
Figure 4-4
Loading...