Philips HTS5100B-F7 User Manual

HTS5100B

Enjoy

Start Disc Playback

A Press [OPEN/CLOSE A] to open the disc tray. B Place the disc on the disc tray with its label side

facing up.

* Make sure the disc is compatible with this unit.

(Refer to page 19 in the user manual for the list of compatible discs.)

C Press [OPEN/CLOSE A] to close the disc tray.

It may take a while to load

the disc.

D Playback may start automatically.

If not, press [PLAY B].

Playback other supported device

VOLUME

Apple iPod

A Connect the docking station to the DOCK jack. B Dock your iPod in the docking station and adjust the

support to fit it. Then turn on the iPod.

C Press [SOURCE] to switch to “iPod” mode. D Start playback on your iPod.

PUSH

www.philips.com/welcome

Connect

Set up

Enjoy

To pause playback: Press [PAUSE F].

To return to the normal playback: Press [PLAY B].

To stop playback: Press [STOP C].

To eject the disc:

Press [OPEN/CLOSE A] to open the disc tray. Remove the disc. Press [OPEN/CLOSE A] to close the disc tray.

OPEN/ CLOSE

PLAY

PAU S E

STOP

Quick Start Guide

What’s in the box?

VOLUME

Main Unit

User Manual

Remote Control

with Batteries

(AAA x 2)

RCA

Video Cable

FM Wire Antenna

Need help?

User Manual

See the user manual that came with your Philips Blu-ray Disc Home Theater.

Online

Go To www.philips.com/welcome.

Hotline

Call 1-866-309-0866 for our operators.

1 Center, 2 Front, 2 Rear

Speakers and Subwoofer

User Manual

Quick Start Guide Registration CardDocking Station

Connect Set up

Basic Connection

A Placement

Proper speakers system placement is important to ensure optimum sound performance.

REAR LEFT

FRONT LEFT

REAR RIGHT

CENTER

FRONT RIGHT

SUBWOOFER

A Place the center speaker above or close to the TV. B Place the subwoofer on the floor, at least one meter

away from the TV.

C Place the front speakers at equal distances from the

TV.

D Place the rear speakers at normal listening ear level.

B Connect the main unit to TV

Using HDMI (best quality)

A Take an HDMI cable. B Plug one end of the HDMI cable into the HDMI OUT

jack of this unit.

C Plug the other end of the HDMI cable into the HDMI

input jack of your TV.

ANALOG VIDEO CONNECTION Option 1 - Using Composite Video

(standard quality)

A Take the supplied RCA video cable. B Plug the yellow RCA video cable into the VIDEO

OUT jack of this unit.

C Plug the other end of the RCA video cable into the

video input jack of your TV.

VIDEOINVIDEO

Option 2 - Using Component Video

(better quality)

A Take a green, blue, and red component video cable. B Plug the component video cable into the

COMPONENT VIDEO OUT jacks of this unit.

C Plug the other ends of the component video cable

into the component video input jacks of your TV.

COMPONENT

VIDEO IN

PB/C

PR/C

*1) This unit is compatible with the progressive scan

system. The feature provides you with the higher quality pictures than traditional output system does. To utilize this feature, a component or an HDMI connection is required. Refer to the “Video Resolution” on page 41 in the user manual to set the resolution.

Supplied cables used in these connections are as follows:

• RCA video cable x 1 Please purchase the rest of the necessary cables at your local store.

C Connect the speakers and

subwoofer

Connect the various colored cables from the speakers and subwoofer to the same colored jacks at the rear of the main unit.

D Connect the radio antenna and

power cable

Keep the antenna away from the electronic devices to prevent unwanted interference.

FM wire antenna

Connect the supplied FM wire antenna to the inner pin of the FM ANT 75 Ω jack. Extend the wire for optimum reception.

CONNECTING THE AC CORD

After you made all necessary connections, connect the AC cord to the AC outlet.

Insert the plugs securely. Incomplete connections will result in the generation of noise.

AC 120V, 60 Hz

AC outlet

Note Refer to the user manual for other possible connections and important safety instructions.

E Connect audio output from TV

(optional)

To hear the TV audio through this unit, use a red and white RCA audio cable (not supplied) to connect the AUDIO IN (AUX) jacks on the main unit to the AUDIO OUT jacks on your TV.

Note When watching the TV programs, you can press [SOURCE] repeatedly on the remote control until “AUX” is

displayed to get the sound output from the speakers.

Finding The Viewing Channel On Your TV

A After you have made all the necessary connections,

press [STANDBY-ON Q] to turn on the unit.

B Turn on your TV. C Press the button on the TV’s remote control that

accesses the external input channel. It may be labeled “SOURCE”, “AV” or “SELECT” (refer to your TV’s user manual). Or press “2” on the TV’s remote control, then press channel down button repeatedly until you see the PHILIPS splash screen.

This is the correct viewing channel (external input channel).

* To call up the home menu, press [HOME ]. Home menu:

Blu-ray Disc Home Theater System

The HTS5100B is now ready for use.

eneral Setup

Video Setu Audio Setu

Listening Viewer

Play Disc Setup

actory Default

SUBWOOFER FRONT

CENTER

REAR

RIGHT

REAR

LEFT

FRONT

RIGHT

FRONT

LEFT