Philips HTS-3582-Mk2 Service Manual

Home Theater BD Player

Second Generation

Service

HTS3582/93/98

TABLE OF CONTENTS

Location of PCB Boards & version variation & repair scenario matrix.....................

Production Speciﬁcations ...............................................................................................1-3

Safety Instruction, Warning & Notes................................................................................1-

D Instruction................................................................................................................2-1

Mechanical and Dismantling Instructions ........................................................................3-1

Software Upgrades........................................................................................................... -1

Trouble Shooting Chart .................................................................................................... -1

Wiring Diagrams ................................................................................................6-1

Electrical Diagrams and Print-layouts .................................................................7-1

Set Mechanical Exploded view ....................................................................................... -1

Revision List .................................................................................................................

This service manual is for HTS3582 Second Generation model,

which is different from the previous generation HTS3582/98/93

models.

For Second Generation mode the serial number begin with

KX2AXXXXXXXXXX.Refer to the rating lable illustration at right.

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips.

Published by Helen-RY 1207 Service Audio Printed in The Netherlands Subject to modification

Page

1-2

-1

CLASS 1

LASER PRODUCT

313978536081

Version 1.

Version 1.1

Version 0.0

PCB BOARD LOCATION:

1-2

MAIN BOARD

LOADER

Version Variation

Type/Versions

Features

MPLIFIER BOARD

POWER BOARD

HTS3582M2

/93 /98

Power supply rating:220-240V ,50Hz X

Power supply rating:110-240V ,50~60Hz

Power consumption:110W X X

Version Variation

Type/Versions

HTS3582M2

Features

Power supply rating:220-240V ,50Hz X

Power supply rating:110-240V ,50~60Hz

/93 /98

Power consumption:110W X X

HTS3582M2/98

Product Specifications:

Note

•

Speciﬁ cations and design are subject to change without notice.

Region codes

The type plate on the back or bottom of the home theater shows which regions it supports.

Country

Asia Pasific, Taiwan, Korea

DVD BD

1-3

Video

•

Signal system: PAL / NTSC

•

HDMI output: 480i/576i, 480p/576p, 720p, 1080i, 1080p, 1080p24

Audio

•

S/PDIF Digital audio input:

Coaxial: IEC 60958-3

•

Optical: TOSLINK

•

Sampling frequency:

•

MP3: 32 kHz, 44.1 kHz, 48 kHz WMA: 44.1 kHz, 48 kHz

•

Constant bit rate:

•

MP3: 32 kbps - 320 kbps

•

WMA: 48 kbps - 192 kbps

•

Radio

Media formats

•

AVCHD, BD, BD-R/ BD-RE, BD-Video, DVD-Video, DVD+R/+RW, DVD-R/-RW, DVD+R/-R DL, CD-R/CD-RW, Audio CD, Video CD/SVCD, Picture ﬁ les, MP3 media, WMA media, DivX Plus HD media, USB storage device RMVB (Available only in Asia Paciﬁ c and China)

•

File formats

Audio: .aac, .mka, .mp3, .wma, .wav, .mp4, .m4a

•

Video:

•

.avi, .divx, .mp4, .mkv, .asf, .wmv, .mpg, .mpeg,

•

.rmvb, .rm (Available only in Asia Paciﬁ c and China)

Picture: .jpg, .jpeg, .gif, .png

•

Ampliﬁ er

Total output power: 600W RMS (30% THD)

•

Frequency response: 20 Hz-20 kHz / ±3 dB

•

Signal-to-noise ratio: > 65 dB (CCIR) / (A-weighted)

•

Input sensitivity:

AUX: 2 V

•

Music iLink: 1 V

• Tuning range:

Europe/Russia/China: FM 87.5-108 MHz

•

(50 kHz) Asia Paciﬁ c/Latin America: FM 87.5-108

•

MHz (50/100 kHz)

Signal-to-noise ratio: FM > 45 dB

•

Frequency response: FM 180 Hz-12.5 kHz /

•

±3 dB

USB

Compatibility: Hi-Speed USB (2.0)

•

Class support: USB Mass Storage Class (MSC)

•

File system: FAT16, FAT32, NTFS

•

Maximum memory suppor t: < 160 GB

Main unit

•

Power supply: 110-240 V~, 50-60 Hz Power consumption: 110 W

•

Standby power consumption: 0.9 W - 0.5 W

•

Dimensions (WxHxD): 360 x 58 x 325 mm Weight: 2.62 kg

•

Subwoofer

Output power: 100 W RMS (30% THD)

•

Impedance: 4 ohm

•

Speaker drivers: 133 mm (5.25") woofer Dimensions (WxHxD): 160 x 267.5 x 265 mm

•

Weight: 2.55 kg

Speakers

Center speaker:

• Output power: 100 W RMS (30% THD)

• Speaker impedance: 4 ohm

Speaker drivers: 1 x 63.5 mm (2.5") woofer

•

Dimensions (WxHxD): 160 x 85 x 95 mm Weight: 0.37 kg

•

Front/Rear speaker:

•

Output power: 4 x 100 W RMS (30% THD) Speaker impedance: 4 ohm

•

Speaker drivers: 1 x 76.2 mm (3") twin driver

•

Dimensions (WxHxD):

•

Speakers: 85 x 160 x 95mm

• Tall speakers: 240 x 1007 x 240 mm

•

Weight:

Speakers: 0.35 kg/each

•

Tall speakers: 1.57 kg/each

•

1-4

Remote control batteries

•

2 x AAA-R03-1.5 V

Laser

Laser Type (Diode): InGaN/AIGaN (BD),

•

AIGaInP (DVD/CD) Wave length: 405 +7 nm/-7 nm (BD), 655

•

+10 nm/-10 nm (DVD), 790 +10 nm/-20 nm (CD)

• Output power (Max. ratings): 20 mW (BD), 6

mW (DVD), 7 mW (CD)

1-5

HTS3582M2/93

Product Specifications:

Note

Speciﬁ cations and design are subject to change

•

without notice.

Region codes

The type plate on the back or bottom of the home theater shows which regions it supports.

Country

China

Media formats

AVCHD, BD, BD-R/ BD-RE, BD-Video,

•

DVD-Video, DVD+R/+RW, DVD-R/-RW, DVD+R/-R DL, CD-R/CD-RW, Audio CD, Video CD/SVCD, Picture ﬁ les, MP3 media, WMA media, DivX Plus HD media, USB storage device

•

RMVB (Available only in Asia Paciﬁ c and China)

File formats

Audio: .aac, .mka, .mp3, .wma, .wav, .mp4, .m4a

•

Video:

•

.avi, .divx, .mp4, .mkv, .asf, .wmv, .mpg, .mpeg,

•

.rmvb, .rm (Available only in Asia Paciﬁ c and China)

•

Picture: .jpg, .jpeg, .gif, .png

Ampliﬁ er

•

Total output power: 600W RMS (30% THD)

•

Frequency response: 20 Hz-20 kHz / ±3 dB

•

Signal-to-noise ratio: > 65 dB (CCIR) / (A-weighted)

• Input sensitivity:

AUX: 2 V

•

DVD BD

•

Music iLink: 1 V

Video

Signal system: PAL / NTSC

•

HDMI output: 480i/576i, 480p/576p, 720p, 1080i, 1080p, 1080p24

Audio

S/PDIF Digital audio input:

•

Coaxial: IEC 60958-3 Optical: TOSLINK

•

Sampling frequency:

•

MP3: 32 kHz, 44.1 kHz, 48 kHz

•

WMA: 44.1 kHz, 48 kHz

•

Constant bit rate:

MP3: 32 kbps - 320 kbps

•

WMA: 48 kbps - 192 kbps

•

Radio

•

Tuning range:

•

Europe/Russia/China: FM 87.5-108 MHz (50 kHz) Asia Paciﬁ c/Latin America: FM 87.5-108

•

MHz (50/100 kHz)

Signal-to-noise ratio: FM > 45 dB

•

Frequency response: FM 180 Hz-12.5 kHz /

•

±3 dB

USB

Compatibility: Hi-Speed USB (2.0)

•

Class support: USB Mass Storage Class

•

(MSC) File system: FAT16, FAT32, NTFS

•

Maximum memory suppor t: < 160 GB

Main unit

Power supply: 220-240 V~, 50 Hz

•

Power consumption: 110 W

•

Standby power consumption: 0.9 W - 0.5 W

•

Dimensions (WxHxD): 360 x 58 x 325 mm Weight: 2.62 kg

•

Subwoofer

•

Output power: 100 W RMS (30% THD) Impedance: 4 ohm

•

Speaker drivers: 133 mm (5.25") woofer

•

Dimensions (WxHxD): 160 x 267.5 x 265 mm

•

Weight: 2.55 kg

Speakers

Center speaker:

•

Output power: 100 W RMS (30% THD)

•

Speaker impedance: 4 ohm

•

Speaker drivers: 1 x 63.5 mm (2.5") woofer

• Dimensions (WxHxD): 160 x 85 x 95 mm

• Weight: 0.37 kg

Front/Rear speaker:

Output power: 4 x 100 W RMS (30% THD)

•

Speaker impedance: 4 ohm

•

Speaker drivers: 1 x 76.2 mm (3") twin driver Dimensions (WxHxD):

•

Speakers: 85 x 160 x 95mm

•

Tall speakers: 240 x 1007 x 240 mm

Weight:

•

Speakers: 0.35 kg/each

• Tall speakers: 1.57 kg/each

1-6

Remote control batteries

•

2 x AAA-R03-1.5 V

Laser

Laser Type (Diode): InGaN/AIGaN (BD),

•

AIGaInP (DVD/CD) Wave length: 405 +7 nm/-7 nm (BD), 655

•

+10 nm/-10 nm (DVD), 790 +10 nm/-20 nm (CD) Output power (Max. ratings): 20 mW (BD), 6

•

mW (DVD), 7 mW (CD)

1-7

Safety instruction, Warning & Notes

Safety instruction

1. General safety

Safety regulations require that during a repair:

. Connect the unit to the mains via an isolation transformer.

. Replace safety components indicated by the symbol

only by components identical to the original ones. Any

other component substitution (other than original type)

may increase risk of fire or electrical shock hazard.

Safety regulations require that after a repair, you must

return the unit in its original condition. Pay, in particular,

attention to the following points:

. Route the wires/cables correctly, and fix them with the

mounted cable clamps.

. Check the insulation of the mains lead for external

damage.

. Check the electrical DC resistance between the mains

plug and the secondary side:

1) Unplug the mains cord, and connect a wire between

the two pins of the mains plug.

2) Set the mains switch the “on” position (keep the

mains cord unplug).

3) Measure the resistance value between the mains

plug and the front panel, controls, and chassis

bottom.

4) Repair or correct unit when the resistance

measurement is less than 1M

5) Verify this, before you return the unit to the

customer/user (ref. UL-standard no. 1492).

6) Switch the unit “off”, and remove the wire between

the two pins of the mains plug.

2.Laser safety

This unit employs a laser. Only qualified service personnel

may remove the cover, or attempt to service this device

(due to possible eye injury).

Laser device unit

Type : Semiconductor laser GaAlAs

Wavelength : 650nm (DVD)

: 780nm (VCD/CD)

Output power : 7mW (DVD)

: 10mW (DVD /CD)

Beam divergence: 60 degree

Note: Use of controls or adjustments or performance of

procedure other than those specified herein, may result in

hazardous radiation exposure. Avoid direct exposure to

beam.

Warning

1-8

1.General

. All ICs and many other semiconductors are susceptible to

electrostatic discharges (ESD). Careless handing during

repair can reduce life drastically. Make sure that, during

repair, you are at the same potential as the mass of the

set by a wristband with resistance. Keep components and

tools at this same potential. Available ESD protection

equipment:

1) Complete kit ESD3 (small tablemat, wristband,

connection box, extension cable and earth cable)

4822 310 10671.

2) Wristband tester 4822 344 13999.

. Be careful during measurements in the live voltage

section. The primary side of the power supply , including

the heat sink, carries live mains voltage when you

connect the player to the mains (even when the player is

“off”!). It is possible to touch copper tracks and/or

components in this unshielded primary area, when you

service the player. Service personnel must take

precautions to prevent touching this area or components

in this area. A “lighting stroke” and a stripe-marked

printing on the printed wiring board, indicate the primary

side of the power supply.

. Never replace modules, or components, while the unit is

“on”.

2. Laser

. The use of optical instruments with this product, will

increase eye hazard.

. Only qualified service personnel may remove the cover

or attempt to service this device, due to possible eye

injury.

. Repair handing should take place as much as possible

with a disc loaded inside the player.

. Text below is placed inside the unit, on the laser cover

shield:

CAUTION: VISIBLE AND INVISIBLE LASER

RADIATION WHEN OPEN, AVOID EXPOSURE

TO BEAM.

Notes: Manufactured under licence from Dolby

Laboratories. The double-D symbol is trademarks of Dolby

1-9

 6HUYLFH+LQWV

 &$87,21

&+$5*('&$3$&,7256217+(6(592%2$5'0$<'$0$*(7+('5,9( (/(&7521,&6:+(1&211(&7,1*$1(:'5,9(7+$7¶6:+<%(6,'(67+(6$)(7< 0($685(6/,.(   6:,7&+2))32:(56833/<   (6'3527(&7,21 $'',7,21$/$&7,2160867%(7$.(1%<7+(5(3$,57(&+1,&,$1

 7KHIROORZLQJVWHSVKDYHWREHGRQHZKHQUHSODFLQJWKHGHIHFWLYHORDGHU 

  'LVPDQWOLQJRIWKHORDGHUWRDFFHVVWKH(6'SURWHFWLRQSRLQWLIQHFHVVDU\

   6ROGHUWKH(6'SURWHFWLRQSRLQW    

  'LVFRQQHFWÀH[IRLOFDEOHIURPWKHGHIHFWLYHORDGHU   3XWDSDSHUFOLSRQWKHÀH[IRLOWRVKRUWFLUFXLWWKHFRQWDFWV¿J   5HSODFHWKHGHIHFWLYHORDGHUZLWKDQHZORDGHU   5HPRYHSDSHUFOLSIURPWKHÀH[IRLODQGFRQQHFWLWWRWKHQHZORDGHU   5HPRYHVROGHUMRLQWRQWKH(6'SURWHFWLRQSRLQW 

$77(17,217KHODVHUGLRGHRIWKLVORDGHULVSURWHFWHGDJDLQVW(6'E\DVROGHUMRLQWZKLFKVKRUWFLUFXLWVWKHODVHUGLRGHWRJURXQG



)RUSURSHUIXQFWLRQDOLW\RIWKHORDGHUWKLVVROGHUMRLQWPXVWEHUHPRYHDIWHUFRQQHFWLRQORDGHUWRWKHVHW

Solder Joint

 

 2QO\DSSOLFDEOHIRUGHIHFWLYHORDGHUQHHGHGWREHVHQWEDFNWRVXSSOLHUIRUIDLOXUHDQDO\VLVDQGWRVXSSRUWEDFNFKDUJLQJ   HYLGHQFH  7KLVLVDOVRDSSOLFDEOHIRUDOOSDUWQHUVKLSZRUNVKRSV

(6'SURWHFWLRQSRLQWLVDFFHVVLEOHIURPWRSRIORDGHU

Notes

Lead-Free requirement for service

1-10

INDENTIFICATION:

Regardless of special logo (not always indicated)

One must treat all sets from 1.1.2005 onwards, according next rules.

Important note be treated in this way as long as you avoid mixing solder-alloys (leaded/ lead-free). So best to always use SAC305 and the higher temperatures belong to this.

Due to lead-free technology some rules have to be respected by the workshop during a repair:

x Use only lead-free solder alloy Philips SAC305 with

order code 0622 149 00106. If lead-free solder-paste is

required, please contact the manufacturer of your

solder-equipment. In general use of solder-paste within

workshops should be avoided because paste is not easy

to store and to handle.

x Use only adequate solder tools applicable for lead-free

solder alloy. The solder tool must be able

x Adjust your solder tool so that a temperature around

360°C

joint. Heating-time of the solder-joint should not exceed

~ 4 sec. Avoid temperatures above 400°C otherwise

wear-out of tips will rise drastically and flux-fluid will be

destroyed. To avoid wear-out of tips switch off un-used

equipment, or reduce heat.

x Mix of lead-free solder alloy / parts with leaded solder

alloy / parts is possible but PHILIPS recommends

strongly to avoid mixed

solder alloy types (leaded and lead-free). If one cannot

avoid, clean carefully the

solder-joint from old solder alloy and re-solder with new

solder alloy (SAC305).

: In fact also products a little older can also

o To reach at least a solder-temperature of 400°C,

o To stabilize the adjusted temperature at the

solder-tip

o To exchange solder-tips for different applications.

– 380°C is reached and stabilized at the solder

x Use only original spare-parts listed in the

Service-Manuals. Not listed standard-material

(commodities) has to be purchased at external

companies.

x Special information for BGA-ICs:

- always use the 12nc-recognizable soldering

temperature profile of the specific BGA (for

de-soldering always use highest lead-free

temperature profile, in case of doubt)

- lead free BGA-ICs will be delivered in so-called

‘dry-packaging’ (sealed pack including a silica gel

pack) to protect the IC against moisture. After

opening, dependent of MSL-level seen on

indicator-label in the bag, the BGA-IC possibly

still has to be baked dry. This will be

communicated via AYS-website.

Do not re-use BGAs at all.

x For sets produced before 1.1.2005, containing

leaded soldering-tin and components, all needed

spare-parts will be available till the end of the

service-period. For repair of such sets nothing

changes.

x On our website:

www.atyourservice.ce.Philips.com

You find more information to:

BGA-de-/soldering (+ baking instructions)

Heating-profiles of BGAs and other ICs used in

Philips-sets

You will find this and more technical information

within the “magazine”, chapter “workshop news”.

For additional questions please contact your local

repair-helpdesk.

Brief Guide for HTS3582M2/98

EN Before using your product, read all accompanying safety

information

MS Sebelum menggunakan produk anda, baca semua

maklumat keselamatan yang disertakan

2-1

User manual

HDMI

EN Stand mount the speakers MS Dirikan dirian pembesar suara

2-2

2-3

EN Connect the home theater MS Sambungkan teater rumah

2-4

FRONT

RIGHT

FRONT

LEFT

FRONT

CENTER

REAR

RIGHT

REAR

LEFT

SUB-

WOOFER

SUB

WOOFER

REAR LEFT

FRONT

LEFT

FRONT

CENTER

FRONT RIGHT

REAR RIGHT

FRONT

RIGHT

FRONT

LEFT

FRONT

CENTER

REAR

RIGHT

REAR

LEFT

SUB

WOOFER

EN Connect to TV in one of these ways MS Sambung kepada TV dalam salah satu cara berikut

2-5

HDMI ARC

HDMI OUT (ARC)

HDMI + OPTICAL

HDMI OUT (ARC)

OPTICAL

HDMI IN

HDMI IN (ARC)

OPTICAL

OPTICAL OUT

HDMI + COAXIAL

2-6

COAXIAL

DIGITAL IN

COAXIAL

HDMI OUT (ARC)

HDMI + AUDIO L/R

AUDIO IN

HDMI OUT (ARC)

COAXIAL

HDMI IN

AUDIO OUT

AUDIO L/R

EN Switch on the home theater MS Hidupkan teater rumah

2-7

EN Complete the ﬁ rst time setup MS Lengkapkan persediaan kali pertama

2-8

HDMI

3 4

5 6

HOME THEATERHOME THEATER

3OHDVHVHOHFW\RXU

9LGHR

FRXQWU\DQGSUHVV2.

$XGLR

1HWZRUN

(DV\/LQN

3UHIHUHQFH

$GYDQFHG

0HQXODQJXDJH $XGLR

6XEWLWOH 'LVF0HQX 3DUHQWDO&RQWURO 6FUHHQ6DYHU $XWR6XEWLWOH6KLIW &KDQJH3DVVZRUG 'LVSOD\3DQHO $XWR6WDQGE\ 9&'3%&

$XVWULD

%HOJLXP

$XWR(1*

(QJOLVK

ɻʼᐥ᛽

0HOD\X

Å¥

ᇓ໗ࡩ฼

EN Use your home theater MS Gunakan teater rumah anda

2-9

2-10

3.5MM STEREO

MUSIC iLINK

2-11

LAN

Brief Guide for HTS3582/93 & HTS3582M2/93

EN Before using your product, read all accompanying safety

information

2-12

HDMI

MIC-IN Converter

User manual

EN Stand mount the speakers

2-13

+ 51 hidden pages