Philips HR 8910 Service Manual
Vision Vacuum cleaner
HR 8910
Service
Information
!
Philips Domestic Appliances and Personal Care
Service
Information
!
Service Manual
PRODUCT INFORMATION
- Maximum air displacement : 34 l/sec.
- Maximum vacuum water column : 290 cm
- Power consumption (IEC) : 1400W
- Dust storage capacity : 4 litres
- Cord length : 8.3 metres
- Filter system (depends on version) : Paper dustbag
: Exhaust S-air fi lter
: Active carbon
protection fi lter
- Dimensions cleaner : 48 x 30 x 25 cm
- Weight without accessories : 6.4 kg
- Noise : 78 dB
- Colour : Blue / grey
OPTIONAL
Exhaust air fi lter - AFS HR 6932 (8836 932 01210)
Oslo cotton dustbag HR 6935 (8836 935 01010)
Oslo paper dustbag set HR 6938 (8836 938 06110) economy
Oslo paper dustbag set HR 6938 (8836 938 10110) hygiene
Oslo 3-M dustbag HR 6938 (8836 938 91010)
Active carbon inlet fi lter HR 6949 (8836 949 01010)
Active carbon fi lter set HR 6968 (items 41 + 42)
S-class fi lter HR 6992 (8836 992 01010)
S-class fi lter set HR 6993 (items 48 + 49)
Polishing nozzle HR 8040 (item 111)
Turbo brush HR 6988 (item 114)
SERVICE INFORMATION
- The infrared remote control can adjust the suction power with
5 speeds. When switched on, the appliance always starts
with the highest power, even without a connected hose.
Use LR03 batteries. Alkaline is advised.
- To open the appliance, fi rst remove the panel (item 13) with a big
screw driver (V) to disconnect the 4 snap locks (the 4 screws of
button panel item 39 can be loosed) and then remove the two
pedals (items 1 and 14) with a pin (W), max. diameter 2.5 mm.
- Power meter (8838 000 60300) is a commercial item with a fi xed
air displacement which measures the vacuum of the appliance.
- Component confi guration on exploded view may differ in case
of specifi c versions. However, the actual components are
distinguished by means of code numbers.
- The spare parts have been standarized as much as possible.
- Item 7A. This appliance is provided with ring 7A. For other parts
use item 6 or 7.
- Item 16 Cotton dustbag is used in those countries where paper
dustbags are not available.
- Item 21 is provided with the long cord-winder spring; both long
and short cords can be used in combination with this spring.
- To disassemble the cordwinder use TORX screw driver no T15,
which is one of a set consisting of T20, T15, T10, T9, T8, T7 and
T6 = 4822 395 50145.
- Item 43 air valve opens to cool the motor if the air displacement is
too low or if the air fl ow is blocked.
- Cordwinder spring has to be tensioned till maximum minus
approx. 1,5 revolution.
This product meets the requirements regarding interference suppression on radio and TV.
Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification
After the product has been repaired, it should
function properly and has to meet the safety
requirements as offi cially laid down at this
moment.
4322 277 00270
00/03
PCS 101 445
1 4322 003 10700 cord-winder pedal
2 4322 003 10690 accessory cover
3 4322 009 07090 acc. cover spring
4 4322 003 10740 lead lid
5 4322 005 06650 acc. cover lock
6 4322 001 72800 diaphragm valve
7 4322 009 06420 swivel connector
7A 4322 003 15820 ring
8 4322 001 71960 sealing rubber
9 4322 003 10650 dust cover
10 4322 000 03800 dust-cover spring
11 4322 003 10640 dust-cover snaplock
12 4322 003 10630 cord-winder lever
13 4322 005 11590 version panel
14 4322 003 10710 switch pedal
15 4322 006 22410 IR-RMC receiver
16 8836 938 10110 oslo paper dustbag hyg.
8836 935 01010 oslo cotton dustbag (opt.)
8836 938 91010 oslo 3M-dustbag (opt.)
17 4322 005 06610 hose + connectors
18 4322 009 06410 dustbag holder
20 4322 009 06390 dust chamber
21 4322 009 05350 reel half spring unit
22 4322 003 10470 connection piece
23 4322 001 72360 brake tyre
24 4322 009 04800 reel half contact unit
25 4322 009 05060 contact-ring plate
2
28 4322 006 01800 cordset UK 1 mm
29 4322 006 00550 cordset 1 mm
30 4322 006 01810 cordset Swiss 1 mm
31 4322 006 00540 cordset Italy 1 mm
L = 8.3 m
2
L = 8.3 m 4.8 mm pins
2
L = 8.3 m
2
L = 8.3 m
32 4322 003 16960 lower housing
33 4322 005 04700 caster assy
35 4322 000 03790 button spring
36 4322 001 98860 switch lever
37 4322 005 04750 parking hook
38 4322 006 50580 main switch
39 4322 003 10620 button panel
40 4322 003 16970 upper housing
41 4322 000 37300 safety fi lter Trio (opt.)
8836 949 01010 carbon fi lter
42 4322 009 07040 safety fi lter + grille (opt.)
4322 003 10950 grille for carbon fi lter
43 4322 005 04730 air inlet valve 220-240V
44 4322 006 22460 power module 230V
45 4322 005 07920 rear wheel
46 4322 003 17580 rear wheel cap
47 4322 003 17000 cord outlet
48 4322 003 16990 S-fi lter grille
4322 003 17700 back grille (opt.)
49 8836 992 01010 S-fi lter
8836 932 01210 AFS fi lter (opt.)
50 4322 009 07460 motor housing
51 4322 009 06450 silencers
52 4322 001 72790 back motor buffer
53 4322 003 09720 suspension bracket
54 4322 000 03700 PCB mounting spring
55 4322 009 06430 motor 1441 - 230V
56 4322 001 72780 front motor buffer
57 4322 003 09820 motor disc
101 4322 009 05400 tube clip assy 32 mm (opt.)
102 4322 004 22150 tube chr. active coupling (opt.)
103 4322 009 05410 tube clip assy 35 mm
104 4322 004 22180 telesc. tube + clamp
105 4322 004 22120 nozzle RD 262 act. coupl.
111 4322 004 22030 Polishing nozzle HR 8040
112 4322 005 11040 Polishing disc
113 8838 041 01010 Polishing brushes HR 8041
114 4322 004 22130 turbo nozzle HR 6988
115 9965 000 03349 coupling piece
116 4822 358 10205 drive belt
117 4822 479 20201 Brush assy
121 4322 001 99120 coupling bush
122 4322 007 45550 coupling spring
124 4322 007 16000 leafspring
125 4322 005 08690 hose + standard bend
126 4322 003 16030 bend RMC
128 4322 006 20590 IR-RMC send unit
129 4322 003 02070 crevice nozzle
130 4322 004 00650 small nozzle
131 4322 004 00590 brush nozzle
DFU 4222 000 47310 vacuum cleaner
DFU 4222 000 47280 polishing nozzle HR 8040
DFU 4222 000 45620 turbo brush HR 6988
M
PCS 101 446
PMT
MOTOR
POWER
MODULE
MAIN
SWITCH
CORD WINDER
IR-RECEIVER
+
CONTROL
IR
IR-TRANSMITTER
W
V
V
W
Loading...