Philips HR 8890 Service Manual
Vision Vacuum cleaner
HR 8890
Service
Information
!
Philips Domestic Appliances and Personal Care
Service Manual
PRODUCT INFORMATION
- Maximum air displacement : 37 l/sec.
- Maximum vacuum water column : 310 cm
- Power consumption (IEC) 225V : 1500W
- Dust storage capacity : 4 litres
- Cord length : 8.3 metres
- Filter system (depends on version) : Paper dustbag
: Exhaust air fi lter
: Motor inlet fi lter
- Dimensions cleaner : 48 x 30 x 25 cm
- Weight without accessories : 6.4 kg
- Noise : 78 dB
OPTIONAL
Exhaust air fi lter HR 6932 (8836 932 01210)
Oslo cotton dustbag HR 6935 (8836 935 01010)
Oslo paper dustbag set HR 6938 (8836 938 06110) economy
Oslo paper dustbag set HR 6938 (8836 938 10110) hygiene
Oslo 3-M dustbag HR 6938 (8836 938 91010)
Carbon inlet fi lter HR 6949 (8836 949 01010)
Carbon fi lter set HR 6968 (items 41 + 42)
S-class fi lter HR 6992 (8836 992 01010)
S-class fi lter set HR 6993 (items 48 + 49)
ADJUSTING THE PCB ON THE MOTOR TO 220V, 60Hz
1. Make sure that the potentiometer (item 58) is set at
min. position.
2. Adjust the potentiometer on the PCB (item 44) on the motor to
220V/60Hz. to allow the motor to run smootly.
Please note: * that the standard setting of the PCB is 230V, 50Hz.
* that there are open-circuit voltages on all wires.
SERVICE INFORMATION
- To open the appliance, fi rst remove the panel (item 13) with a big
screw driver (V) to disconnect the 4 snap locks (the 4 screws of
button panel item 39 can be loosed) and then remove the two
pedals (items 1 and 14) with a pin (W), max. diameter 2.5 mm.
- Power meter (8838 000 60300) is a commercial item with a fi xed
air displacement which measures the vacuum of the appliance.
- Component confi guration on exploded view may differ in case
of specifi c versions. However, the actual components are
distinguished by means of code numbers.
- The spare parts have been standarized as much as possible.
- Item 7A. This appliance is provided with ring 7A. For other parts
use item 6 or 7.
- Item 16 Cotton dustbag is used in those countries where paper
dustbags are not available.
- Item 21 is provided with the long cord-winder spring; both long
and short cords can be used in combination with this spring.
- To disassemble the cordwinder use TORX screw driver no T15,
which is one of a set consisting of T20, T15, T10, T9, T8, T7 and
T6 = 4822 395 50145.
- Item 43 air valve opens to cool the motor if the air displacement is
too low or if the air fl ow is blocked.
- Cordwinder spring has to be tensioned till maximum minus approx.
1,5 revolution.
This product meets the requirements regarding interference suppression on radio and TV.
After the product has been repaired, it should
function properly and has to meet the safety
requirements as offi cially laid down at this
moment.
Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification
4322 277 00268
00/03
PCS 101 430
1 4322 003 13180 cord-winder pedal
2 4322 005 07640 accessory cover (standard)
3 4322 009 07090 acc. cover spring
4 4322 003 13350 lead lid
5 4322 005 06650 acc. cover lock
6 4322 001 72800 diaphragm valve
7 4322 009 06420 swivel connector
7A 4322 003 15820 ring
8 4322 001 71960 sealing rubber
9 4322 003 13060 dust cover
10 4322 000 03800 dust-cover spring
11 4322 003 13580 dust-cover snaplock
12 4322 003 10630 cord-winder lever
13 4322 009 06830 version panel (standard)
14 4322 003 13220 switch pedal
16 8836 938 10110 oslo paper dustbag hyg.
8836 935 01010 oslo cotton dustbag (opt.)
8836 938 91010 oslo 3M-dustbag (opt.)
17 4322 005 04740 suction hose (460)
18 4322 009 06410 dustbag holder
20 4322 009 06390 dust chamber
21 4322 009 05350 reel half spring unit
22 4322 003 10470 connection piece
23 4322 001 72360 brake tyre
24 4322 009 04800 reel half contact unit
25 4322 009 05060 contact-ring plate
26 4322 007 11960 cordset Australia
27 4322 007 12150 cordset Japan (2 x 1.25 mm
4322 006 01620 cordset (2 x 0.75 mm
L = 6.3 m
2
)
2
)
28 4322 007 12190 cordset UK L = 6.3 m (opt.)
2
4322 006 01800 cordset UK 1 mm
29 4322 007 11930 cordset
L = 6.3 m 4.8 mm pins (opt.)
4322 006 00550 cordset 1 mm
L = 8.3 m
2
L = 8.3 m 4.8 mm pins
30 4322 007 12020 cordset Swiss L = 6.3 m (opt.)
2
4322 006 01810 cordset Swiss 1 mm
L = 8.3 m
31 4322 007 11950 cordset Italy L = 6.3 m (opt.)
2
4322 006 00540 cordset Italy 1 mm
L = 8.3 m
32 4322 003 16960 lower housing
33 4322 005 04700 caster assy
35 4322 000 03790 button spring
36 4322 001 98860 switch lever
37 4322 005 04750 parking hook
38 4322 006 50580 main switch
39 4322 003 13140 button panel
40 4322 003 16970 upper housing
41 4322 000 37300 safety fi lter Trio
42 4322 009 07040 safety fi lter + grille
43 4322 005 04730 air inlet valve 220-240V
44 4322 006 20720 power module dt 230V
45 4322 005 07920 rear wheel soft black
46 4322 003 13300 rear wheel cap
47 4322 003 17000 cord outlet grey
48 4322 003 17700 back grille grey
49 8836 932 01210 AFS fi lter
50 4322 009 07460 motor housing
51 4322 009 06450 silencers
52 4322 001 72790 back motor buffer
53 4322 003 09720 suspension bracket
54 4322 000 03700 PCB mounting spring
55 4322 009 06430 motor 1441 - 230V
56 4322 001 72780 front motor buffer
57 4322 003 09820 motor disc 1241-1441
58 4322 006 20760 potentiometer 220-240V
59 4322 005 04810 suction power indicator 220-240V
120 4322 009 05400 metal-tube clip
121 4322 002 22610 metal-tube
122 4322 009 05410 telesc. -tube clip (opt.)
123 4322 004 21050 telescopic tube (opt.)
125 4322 004 27440 eco bend + hose
126 4322 005 03770 eco bend
127 4322 004 21810 nozzle RD 262 con.
128 4822 479 20123 nozzle strips
129 4322 003 07620 crevice nozzle
130 4322 004 21160 small nozzle
131 4322 004 21170 brush nozzle
DFU 4222 000 47300 West Europe total
M
PCS 101 431
CONNECTOR
MOTOR
POWER
MODULE
MAIN SWITCH
MAX
MIN
CORD WINDER
W
V
V
W
Loading...